No signal on mixer on any channel?

Hi...
One minute my track was going fine the next minute there is no sound, no signal from any of the channels.
I have checked the audio output is correct. (itunes and other apps working)
I have loaded an earlier version of my project and this plays and the level are going.
I dont know what i did i think i must have hit my keyboard as i lent over to grab something...
Any ideas?

Hi thanks for the response.
nothing is muted. the levels actually go up and down even when muted. But there is no signal at all going to the mixer.
strange never had this before...

Similar Messages

WRT110 signal problems... change channel?

I have been having significant slowdown using my wireless router. Someone in a differfent post said he was told by comcast that his signal could be inconsistent because comcast uses the same channel, which causes interference. I too have comcast, so I want to try this. Unfortunately, the threads I've read only give directions up to accessing the Linksys administration tool and I cannot find any way to change channels once I get there.
When I get to the Wireless tab, I see manual and wi-fi protected options, and it is default filled to wi-fi protected. Option 1 [holding the wi-fi protected set-up button and hitting the button to the right] results in a failed attempt to contact the client device. Option 2 requires a PIN and I have no idea what that would be. Option 3 gives direction if my router asks for a client PIN number... no idea how to get to whatever point the router would ask for that info.
OTOH, if I click the manual setup radio button, I go to a page that only offers a few set-up options [Network Mode, Network Name (SSID), Radio Band, Wide Channel (only option is auto), Standard Channel (only option is auto), SSID Broadcast]. In other words, I can see no way to set to channels 1-6, 9, 11 as others have recommended.
What the heck am I doing wrong?
TIA

>Someone in a different post said he was told by comcast that his signal could be >inconsistent because comcast uses the same channel, which causes >interference.
First that is a bunch of crap. You WAN input is not on any 'channel'. Next don't ever hit the SES button (Secure Easy Setup) on the front of the router because you don't have the receiving hardware to take advantage of it. The wireless tab always defaults to WiFi Protected Setup but you always want Manual.
Never use the Linksys Admin Tool LELA. Always connect to your router via your wired computer to 192.168.1.1. Leave user name blank and input your password that you set (might be admin).
Under basic wireless settings:
Network Mode - BG Mixed (my setting)
SSID - your network name
Radio band - Standard 20Mhz
Wide channel - Auto
Standard channel - 1 (higher frequencies are not as reliable)
SSID - Enabled
Basic Setup Tab change MTU value to Manual 1492 if you have PPPoe, otherwise lower it to 1400.
Advanced wireless settings change Beacon Interval to 75, RTS and Fragmentation threshold to 2404.
Save settings and give it a try. Once your wireless is stable, go back and add security.
Message Edited by sabretooth on 12-01-2009 11:59 PM
Message Edited by sabretooth on 12-02-2009 12:01 AM

Equium A110-252: I can't get any channels with V-GEAR MobiDTV

Hi.
I have the Toshiba Equium A110-252 and i've just bought the V-GEAR MobiDTV but I can't get any channels. Do
es anyone know if this laptop has the correct software/hardware that is needed.
Hope someone can answer this for me.
Thanks

Hi
This is not a Toshiba device and in such cases the best way is to contact the device manufacture.
In your case I would recommend visiting this site:
http://vgear.com/products/list.asp?ProdID=AMVG1-016-002
However, I assume this tuner should receive the digital signals.
I dont know where you live but in my knowledge the digital TV is not available everywhere. The digital signals must be strong enough to receive the TV channels.

All of a sudden, I can no longer add any plugins to any channel strips? And when I click on an existing plugin to edit, it disappears off the channel strip?

I am running Logic express 9 on a 2008 Macbook, (non pro). Anyhow, logic has always seemed to work great for me. However, last week I opened up one of many existing projects, (I'm in sample editor). When I went to add a new plugin to one of the channel strips it would not allow me to. Also, if I click on any plugin that already exists on the channel strip it dissapears? The strange thing that also happens weather I click to add a new plugin or click on an already existing plugin, is both the "repeat section" and "crop", buttons from the above menu (in sample editor), the actual buttons become a faded image,(as far as the actual font and images of the buttons). As soon as I am done clicking to add a plugin on the channel strip, both buttons from the menu go back to looking normal like all of the other choices from that menu? I really don't get it? All I want to do is to be able to add plugins as well as edit or change plugins again. Any thoughts as to why I can no longer add any new plugins to any channel strips? And why any existing plugins disappear from the channel strip when I click on it? Why the "repeat section", and "Crop", buttons from the menu above fade in and out when I try clicking on the channel strip is very strange? I don't mind that I just want to be able to add or edit plugins again. I did do some document cleaning up last week as my memory was getting low. I then emptied out my trash bin. I'm hoping I didn't accidentally delete some kind of Logic component? Why can't I add or edit plugins anymore? Anyone ever run across this?
Thanks,
Mike.

Mike,
Are any of your other applications going wonky, or is it just Logic?
I'm afraid I've never heard of this particular problem before, but if it were happening to me the first thing I would do is delete my "com.apple.logic.express.plist" file in Library>Preferences, then repair permissions in Disc Utility, and finally restart my computer. Then I would launch Logic and see if the problem has been corrected. It's amazing how much these two steps can accomplish.
If that doesn't resolve the issue I would launch Logic and go to Preferences>Audio Units Manager to see if all my plug-ins are properly validated.

I could not configure a DAQ assitant for any channel

In the wizard after selecting the voltage input i am not able proceed forward i.e i could not find any channels to select in Mychannelsbox,so can any one tell me what should i do and what all the software i need to install to use DAQ.i have complete labview development suite version 7.0 ,i hope to get reply as early as possible,bharat

What version of NI-DAQ are you running? What DAQ card do you have? If you do not have a DAQ card installed, you will be able to start the DAQ Assistant but not complete it since you have no available channels (no card installed).
If you do have a DAQ card installed, is it functioning in MAX? Can you run a test panel on it?

Error when access instrument "Primary Error: (Hex 0xBFFA003D) Unable to find any channel or repeated capability strings"

Hi All,
I believe I have configured MAX correctly. I am trying to use the PXI-6229 device via. When I try initialized I receive the following error:
Primary Error: (Hex 0xBFFA003D) Unable to find any channel or repeated capability strings.
Any clues on what the error means?
Thanks
Minesh
Solved!
Go to Solution.

First of all you'll get more help in the correct forum. This seems like a DAQmx issue and their forum is here: http://forums.ni.com/t5/Multifunction-DAQ/bd-p/250
Secondly does this help: http://forums.ni.com/t5/Switch-Hardware-and-Software/NI-SwitchExec-with-3499-and-IVIDriver/td-p/1827...
Lastly: Can you communicate with the card from MAX? Or is the error happening in MAX? What language are you using to talk to the card with? Are you using IVI? If you are using LabVIEW or CVI then open the shipping examples and test them out with that card.
Regards,
jigg
CTA, CLA
teststandhelp.com
~Will work for kudos and/or BBQ~

Unplugged tv and now I don't have any channels?

I quickly unplugged my tv and set top box and then when I plugged it back in it showed that I couldn't get any channels. It would just say "[insert channel] is currently unavailable". I tried rebooting it multiple times but it still didn't do anything. Any suggestions?

If you have another room with a STB try swapping the boxes to determine if the box is good elsewhere and the tv works before contacting Verizon.

I seem to have very poor wifi signal strength,is there any way to boost my signal

I seem to have very poor wifi signal strength,is there any way to boost my signal

If you gave some information on what network equipment you are using (make, model, version) and where you are experiencing signal problems it would help in giving advice.

New customer, cant get any channels

Hi,
So i've set up my new vision+ box today and followed the instructions to the letter. Used all the cables provided and checked all the right lights and flashes are doing their thing. But...i can't get any channels at all! Nothing. I've unplugged everything and started again to no avail, i've rebooted my home hub and i've checked my tv works ok without vision.
Does anybody have any ideas? I have a freeview enabled tv in another room and it works fine.
If this doesn't get resolved soon then i think i may just have to go back to Sky.
Thanks in advanc for any advice

Hi AnnaP and welcome
Is the other TV supplied from the same aerial?
If it is, unplug it and then try this...
(The same goes for any other TV's, should they also be running off the same aerial)
Remove the main aerial lead from the rear of the vbox and scan for channels (it will never find any)
When it's finished scanning, leave the Vbox switched on and switch off the mains plug for the Vbox.
Insert the main aerial lead back into the Vbox, but remove the aerial lead that goes from the Vbox to the TV (if fitted).
Plug the box back in and repeat the scan for channels.
Does it find any channels?
(Don't forget to plug the other aerial lead into the other TV)
edit. If you're using a HDMI connection, unplug this and use a scart lead
-+-No longer a forum member-+-

"Up Mix" from 2-channel "Stereo" audio content to 5.1/7.1 Surround

Hello,
This is a feature that I had strongly hoped would make it to Media Center in Windows 8, but didn't. Please consider this for a future update and/or the next version of Windows...
Feature Request: "Ability to Configure Stereo Up-Mix Capability in Windows Media Center and/or Windows Media Player from 2-channel Stereo to 5.1/7.1 Surround so Stereo MP3/WMA audio files output to *all* speakers in my system, not just the left and
right main speakers."
More information:
My audio content (MP3s, WMAs, etc.) are of course all 2-channel stereo format (left channel, right channel). My home theater PC outputs to my home theater receiver (which is a 2012-model Sony 5.1/7.1 receiver) via HDMI. When I play
2-channel music (MP3s, WMAs, etc.) from Windows Media Player (WMP) and Windows Media Center (WMC) both in Windows 7 and Windows 8, I only hear music from the left and right main speakers, *not* the subwoofer not the rear surround speakers.
In order for this to happen, WMP/WMC would need to "up mix" the stereo signal to take full advantage of my physical speaker configuration (as specified in my Windows' Playback Devices configuration, which Windows is able to discern from the capabilities of
my receiver). Media Center even has an Audio setup in which the end user configures the audio configuration to either Stereo, 5.1, or 7.1 yet music is still output over only two channels!
I would like to see WMC/WMP either "automagically" perform the "up mix" or provide the user with an option to enable/disable it when 2-channel Stereo audio content is played.
Too difficult? Rhapsody.com already accomplishes this with its online audio player! Note that my audio equipment has the capability of forcing output to two channels between the PC and the receiver, which my receiver will then up-mix, but this
requires physically maintaining a dip switch and also several button presses on my receiver's remote... and this physical configuration must be updated each and every time I switch between audio and movies. Too much work when it could be accomplished
automatically by WMP/WMC!
Thank you for your consideration of this feature request!
-Tretchie

The ability of windows to better control audio channel output is definitely an issue that needs to be fixed. It's really basic in this day and age where everyone and there mother has more than two speakers (i.e. 5.1 or 7.1). I understand that certain media
players, or certain decoders/channel mixers can be a workaround for this problem. But that's not enough. Today, we have many different sources for audio that are not just files on a computers:
1) Video/Movie files on computers (played through media center, MPC-HD or other)
2) MP3s/audio (played through same)
But there is also:
HTML5, webpages, Netflix, Amazon TV, Flash players, silverlight, etc. etc.
Hence why windows needs an option at the level of windows audio decoder to better control channel outputs over LPCM-HDMI! Either Mirroring L/R outputs to rear/side speakers, or, formal upmixing algorithms like Dolby Pro Logic etc., applied before
outputting over HDMI (Note I am NOT talking about bitstreaming!)
This is a trivial problem using WASAPI or ASIO. Why has windows audio not been properly updated since Windows XP!!
Recently, HTPCs and Media Centers are becoming many households primary source of entertainment.
Examples of some issues:
1) With no bitstreaming at all:
- Configuring HDMI audio "Playback device" to 5.1/7.1, and,
- Using a software decoder/media player to decode Dolby Digital, DTS, DTS-True HD, or Dolby True HD, and sending the data in LPCM over HDMI to the receiver/soundbar
-> works totally fine for outputting 5.1/7.1 surround from those sources
-> windows (i.e. software) completely fails in any ability to upmix 2.0 stereo sources to 5.1 or 7.1, or even mirror L/R channels to rear/side L/R channel for more room filling sound. Both these options should be available - upmixing with Dolby or other
for videos and mirroring/doubling the channels for music/MP3s.
Instead, windows audio sends silent channels over LPCM/HDMI when playing a stereo source. This has the added awful effect of not even letting my receiver upmix/mirror the outputs.
Hence, we need the ability to duplicate (for audio) and upmix (for videos) the L/R channels in a stereo source to the Rear L/R and or Side L/R channels through windows audio "playback devices" configuration before outputting over HDMI-LPCM!
In the day and age of 5.1 and 7.1 speakers this seems like such a BASIC feature that is missing.Otherwise, so many of us with an HTPC in our living room as our main source of media can't play music mirrored
through all our speakers, or watch videos with upmixed audio.
HDMI is the new standard, so this should really become an option.
I've done a fair amount of research on this problem, and do not believe there is any solution short of switching to optical (which I do not want to do because it can only carry 5.1) or, buying a fancy receiver instead of a soundbar with discrete rears and
a subwoofer (which I have) to do the mirroring/upmixing for me.

Connecting more than one sensor cable to screw terminal to collect more than one signal in single DAQ board channel?

I don't know if this topic is being posted in the correct location. I am new to LabVIEW and the hardware associated with it. I am using an NI 9237 DAQ board for a senior design project in engineering and I was informed that I can make multiple connections to a single screw terminal which in turn will connect to one channel of the DAQ board. To give the specifics, I have two pressure transducers and would like to connect them to the same screw terminal and channel on the DAQ board yet separate them when acquiring data in the VI. Does anyone know how to do this? I know is is essentially knowing what pins do what on the screw terminal but I can't find this anywhere. I am currently doing the job with two screw terminals and two of everything else (RJ50 adapters, etc.). I would appreciate any input. Also, please let me know if I am posting in the wrong board and if possible, which board I should be posting to.
Thank You,
bsteinma

bsteinma,
What you may have heard is that you can measure multiple signals on the same task, not on the same channel. By tying both of these signals to the same channel, both signals will compete to drive the line. The channel on the card will only interpret this garbled signal and you will get no useful data. If you are new to wiring up hardware, I recommend configuring a task within Measurement and Automation Explorer and then clicking on the tab along the bottom of the page titled, Connection Diagram. This will show you what electrical connections to make. Then, in LabVIEW you can read multiple signals (channels) and manipulate each signal how you would like.
As far as boards go, you will generally find an answer where ever you post, but the Multifunction DAQ board is a great place to post when you have questions regarding hardware (like your 9237).
Cole R
Applications Engineer
ColeR
Field Engineer

WRT300N Not broadcasting on any channel

I've had my WRT300N v1 (firmware version 1.03.6) for about a month now (just long enough to not be able to return it to Best Buy). I got it to replace a Linksys wireless-B router that I had had for many years, but which stopped working altogether. Before dying, I had no problem getting strong signal anywhere in my apartment or even outside through multiple walls.
With the new router, my laptop (which has a wireless-b card built in and is running Win XP Pro) is currently sitting 3 feet from the router and is not detecting the network. I've tried setting the network mode to Mixed, BG-Mixed, and to B Only. I've tried all 11 channels. I've tried changing the beacon interval, fragmentation threshold, and RTS threshold as recommended elsewhere. I've tried turning off security (although when I first set it up, I didn't turn on the security and within a day there were two people leaching off of my connection).
If I power down the router and then power it back up, the computer detects the network for a few minutes before it goes away again. In addition, I've got a wireless appliance on my stereo (SlimServer Squeezebox) which has built in wireless-g which exhibits the same sort of behavior. When I power cycle, I can get 75% signal (less than what I had with my old router), but as soon as I connect, it loses the signal. The signal meter on the Squeezebox currently reads 0%.
The wired portion of the router is working just fine, and I have no problem connecting either my desktop or my laptop with an ethernet cable.
Is there anything else I can try, or should I just contact customer support to arrange for a return or refund?

Looks like the only carriers in the US will be Direct TV and Dish Network.
You could watch it on-line via www.willow.tv but it looks like a subscription to that will run about $130
====================================================================================
Error exists between keyboard and chair.

SAP audio language not working for *any* channels. Useless tech already came out!

Just got the FIOS service this Friday.
I'm very happy with the internet. Very fast!
The TV, I'm not so happy about.
Having come from AT&T U-Verse, and Time Warner Cable before that, I've gotten used to having the HBO channel lineup (or any premium channels like Showtime/Cinemax/etc) and being able to easily switch between English and Spanish audio. So far, between 6 calls to customer service (each one of them telling me it's possible), and one extremely clueless tech that just left my home after only 5 minutes, I've not been able to do this.
I can SEE the option for SAP! I KNOW HBO offers Spanish audio for its' non-HBO Latino channels. I also know that not all movies have Spanish audio, but the majority of new HBO movies do.
A guy on the phone on Saturday had me convinced that to watch HBO channels with Spanish audio, I had to purchase your Spanish package that comes with extra Spanish channels. I thought this was ridiculous -- since I've already got a PREMIUM package, why in the world would I need to get another package to listen to that premium one in Spanish?! Anyways, I got the package and still no Spanish HBO.
The tech that came and left in 5 minutes changed the channel to HBO Latino and said, "Here, it's working". I pointed out that HBO Latino is not what I meant - none of the other HBO channels have Spanish, althought we could see they said SAP.
What gives, Verizon? This, coupled with the fact that I can't set my main DVR to record a show we're watching on an HD receiver in another room without physically going to the DVR itself (or using a cellphone app!) and that apparently I can only record 1 show on the DVR at a time, has me pining for AT&T... which I never thought would happen.
Hell, even Time Warner Cable's HBO lineup has Spanish.
Sounds to me like your all-fiber network isn't up to snuff on some very basic things.

skohly wrote:
Chill man
On your remote push the option button. Then click on audio language and change to spanish. You will be all set
We've been through that appx. 50 times with tech support - not working. Tech guy that came out today said Verizon doesn't offer SAP ... so I don't know what to think now.

Bt vision box wont let me watch any channels while...

bt vision box while recordin 1 programme i go to another channel to watch it says no signal or weak signal, and the rest of the channels say the same thing. we have recently brought a new areil lead which is shielded,we stayed on a channel wid the blank screen and when the recordin finished the picture came up we have had problems before this its very annoyin all we do is try and fix this problems any1 know what could be wrong.

no signal or weak signal normally mean an aerial problem or you are in a poor reception area at the moment till the digital switch-over is completed in your area
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

No signal on bbc hd,itvhd,channel 4 hd????

Help needed please Iv recently moved into a flat and the flat has a communial arial which we plugged in. Weve been in here for 3 months. The signal has been fine but in the last week or so the signal has dropped from bbc hd , itv hd and channel 4 hd. All other hd channels work fine. I have checked the connections into the box and tv and also turned off and back on. Does anyone know what has happened or if there is something i can do?

ashley1047 wrote:
.......Does anyone know what has happened or if there is something i can do?All that's happened is that some PSB HD regionals have moved satellite in the last week or so, and I think they're now on an Astra 2G ( new satellite ) UK spot beam which means that if you're outside UK the chances are these will no longer be received without a larger dish. If you're in UK, and have fully rebooted the Sky+HD box at the mains, and still no joy, I suggest you follow Mark's advice and speak to whoever is responsible for getting the building's communal system looked at.

No signal on mixer on any channel?

Similar Messages

Maybe you are looking for