No signal with Airport express

I have been using Airport Express for almost a year so that I could use Airtunes. It has worked fine until just recently.
I have a PC in a home office that is connected to my router, a Powerbook next to it which connects via AE, as does another laptop downstairs. We lost internet connection on the 2 laptops a few days ago and since then I have Hard reset the AE a few times as I was able to establish connection for a few minutes then it would drop out again. Now however, I am unable to pick up the AE in Airport Utility at all. The light is green on AE but it just doesn't find it. As far as I am able to tell I am up to date on Firmware (assuming that is part of the software updates?)
Any suggestions would be much appreciated!

What neighbors do you have, how close?
I suggest you run iStumbler or something similar to find out if other WiFi routers are competing with your AX. Also there may be some other electronic device such as a wireless phone that is interfering. I don't know how you could detect the latter.
I found designating a channel worked for me. My AX would automatically stick to channel 1 and I had lousy reception. specified channel 8 in airport utility for the AX and problem is solved, for now at least.

Similar Messages

Boosting o2 Wifi signal with Airport Express

Dear all,
I had read that one could boost our o2 Wifi signal with the Airport Express. I don't seem to be able to do it! Can anyone help.
Detsky

It is possible if the wireless network is created by another AirPort Express (AX), an AirPort Extreme base station (AEBS), or a Time Capsule. Otherwise it is not possible.

How: Extend a non-Apple wifi signal with Airport Express

I have a Wifi modem provided by the ISP, Tiscali [Italy] unrelated to Apple. I want to use my AE to extend the signal to another part of the house. The Tiscali router was set up with WPA2. I have Airport Utility 5.6.1 [yah, I know, old; haven't moved up from OS 10.8.5 either, MBk Pro] and the Airport Express is MC414Z\A C86L9K02DV3R. Opening the A Util w the AE powered up [yellow light showing] I immediately saw the AE listed at the left, but now that I go back to the Utility and rescan, it doesn't find the AE, altho Airport is one and lists that AE showing a full signal, properly calling it "gatti.11n." Your advice would be most appreciated and likely will be helpful to many others saddled with a non-Apple wifi router.

Apple AirPorts cannot wirelessly "extend" a signal from a third party product. They can only wirelessly "extend" a signal from another Apple router. Another way of saying the same thing is that if you want to wirelessly extend a network using an Apple router, you need two Apple routers.
You have two options:
Option 1. Add another AirPort Express and install it close to the ISP modem/router using an Ethernet cable and configure the Express to 'create" a wireless network. Then, your other AirPort Express can wirelessly extend the signal from the first AirPort Express. The "extending" Express will need to be located where it can receive a strong signal from the first Express.
Option 2. If you cannot run the Ethernet cable....or....you do not want to add another AirPort Express, then a pair of Ethernet Over Powerline (EOP) adapters might be able to send the Ethernet signal over the existing AC powerlines in your home. These products are also sometimes called HomePlug adapters.
The theory with these devices is that you already have the wiring in place.....you just need the adapters. In practice though, things do not always work as well as the theory might suggest. So, if you decide to try a pair of these adapters, then it would be good idea to understand the store's return policies before you buy.
Any computer / electronics superstore will have a selection of EOP adapters. Ask the salesman what type and brand that he would recommend.

Boost Wireless Signal with Airport Express

I bought the new airport express to boost the signal from my time capsule (in my house) to my garage office.
I have the AX set up but I don't see any difference in the signal.
What am I doing wrong?

Mike, welcome to the discussions!
Check the settings for both devices using AirPort Utility as follows:
1) For the Time Capsule, click on Manual Setup and then click the Wireless tab below the row of icons to display the wireless settings for your TC. Make sure there is a check mark next to "allow this network to be extended"
2) For the Express, click Manual Setup and click the Wireless tab. Wireless Mode should be "extend a wireless network" (Users often choose "join" by mistake when they are trying to extend the network). Make sure there is a check mark next to "allow wireless clients".
Any improvement?

Extending the wifi signal with airport express

I tried to extend my network with a new apple express. My wireless internet service works from my older airport extreme base station, but the a window comes up that says "No base stations were found on "your network”. Choose a different network or go back.
Not sure why I can be connected wirelesslyto my network, but no base stations were found.

thanks for responding. I've turned all off, then back on. When I go to airport utility, this window comes up "
This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information.
Again, my computer is connected via wi-fi, yet the airport base station is not recognized. Certainly, when airport utility is opended we have the symbol for internet showing, as well and the airport extreme connection with the correct network name.
the model S/N of the airport extreme is SNH53340C3NW2 Not sure which number the model number is..
So, I tried this....
I took my laptop and airport express into the room where the wireless airport extreme modem is, and configured the airport express from there. Now the express shows on both computers. But, when I click on the extreme icon, it still says that airpot utility does not support this base station. Does this matter at all? Seems to me the system is not recognizing the express.
thanks for your input!

IPad and iPhone 4 and new 5s drop connection with airport express. This just started recently after working fine for a year. PC does not drop. Wifi signal fine. Help?

Streaming music with airport express and Apple TV to 2 different systems. No problem with Apple TV. iPad and iPhone 4 and new 5s keep dropping their connection to airport express. Airport express connection to wifi appears to be fine. No dropping by windows PC. This just started recently after working fine for a year. Help?

What does any of this have to do with the Apple TV?

Trying to set up wireless network on PC with Airport Express

I'm helping a friend set up his network with AirPort Express. He's got a modem attached to his PC, and currently has a router that sends a wireless signal to a receiver on the PC in the other room. Now he's added a Mac, and the old router/receiver doesn't work with Mac. So he bought an Airport Express.
I've turned on the Airport, and first I connected the ethernet cable from the modem to the AirPort. Per the AirPort utility I put on the PC, it couldn't find it (got the flashing amber light). So then I took out that ethernet, and I hooked up the ethernet directly from the CPU to the AirPort. Suddenly, it was found, and it took me step by step through the set up. It asked for password info from our internet provider (??why would I have that info??), so we just hit "enter". Then it couldn't set up the network, and said to check the "manage network settings". I've tried everything. Not only can I NOT manage to create a network, but now NEITHER ethernet cable will cause any recognition in the AirPort. All I get is the blinking amber light. I'm about to throw all the computers out the window...it really should not be this difficult. I've set up networks in my own home, before, with both PC and Mac, and never had these problems. So, now, I've had to relink up the old router/receiver in order to send out this call for help. Can anyone suggest anything else to try before I use these computers for target practice?
Thanks in advance,
Jennifer
P.S. The main PC w/modem is on Vista with service pack 2.0...since I can't even get that one working with AirPort, I hardly think it matters what the other computers are...

I had some initial problems too. Make sure that you have the latest Airport Utility in the utilities folder. I used that to correct the problems I had when I first got Time Machine. I recommend resetting everything through there to get it working right.
Mine is not set up to run an n network because my macs are all g and b compatible. Does the airport utility see the time machine? And if so, does it have a green light in the utility?

When adding WRE54G to wireless network incompatible with Airport Express

I added a Linksys WRE54G to expand my network to a Powerbook G4 laptop with a weak signal. When I connect the wireless expander, I no longer see the Airport express in the airport utility. I cannot access the printer or itunes speakers attached to the airport express. When I power off the expander and have a weaker signal, the airport express is available again. I don't know how to configure the wireless expander to work with airport express, and if I try to create a WDS network with the airport express (currently unsuccessful), then I believe I will lose itunes support (and maybe the printer?).
Does anyone know how to configure the WRE54G so that I can still see the airport express on my network?
Thanks,
Brigitte

I was having the same problems. Try this link, someone seems to have solved it.
http://discussions.apple.com/thread.jspa?threadID=1271648

Extending a time capsule with airport express twice

Hi,
I have been trying to extend my existing wireless network recently but it never ended up how I wished...
I have one 4th generation Time Capsule (A1409) and two Airport Express 802.11n (1st generation A1264).
All currently have MAC Address base authentication and no security in place for was of testing (security not relevant at this point in time).
When I extend my Time Capsule with either Airport Express this works like a charm, the LEDs are all green and connection works for client devices.
When I extend my Time Capsule with both Airport Express the same applies, everything works.
However what I have found not to works it extending my Time Capsule with one Airport Express and then extending this Airport Express with the second Airport Express. While all LEDs are green and the second Airport is seen in the Airport Utility, I find no client are ever able to connect to it and alway either connect to the first Airport Express or to the Time Capsule. This is an issue I the area I want to cover is pretty big and I need the second Airport Express for the additional reach.
I haven't found anything against this setup, it however appears you can't connect to the second Airport. The Airport Utility would even accurately depict the situation with Airport Express one dotted line to Time Capsule, and Airport Express two dotted line to Airport Express one.
However no connection seam possible to Airport Express two.
I have swapped Airport Express one and two, and in this case Airport Express gets the clients and Airport Express one now extending Airport Express two gets none.
Is this an expected behavior, i.e. should I give up or is there anything I can do about this ?

However what I have found not to works it extending my Time Capsule with one Airport Express and then extending this Airport Express with the second Airport Express.
Apple's "extend a wireless network" feature will only allow you to extend the signal one level, not two. It's possible to have more than one device extending the signal, but each extender must connect directly to the main base station.....not to another device that is already extending the signal.
The Airport Utility would even accurately depict the situation with Airport Express one dotted line to Time Capsule, and Airport Express two dotted line to Airport Express one.
This is an illusion. AirPort Express is "joining" the wireless network.....not extending it. When the Express "joins" a network, it can be used for AirPlay, or a remote printer could be connected to the USB port, but the Express will not provide any additional wireless signal coverage when it joins a network.
Is this an expected behavior
Yes. I can try to look up Apple's support document that explains this if you want more information, but you may likely already have all the information that you need. Let us know.

My two iMacs frequently go offline when I have our iPad and two iPhones-5 connected with Airport Express (2nd edition). If I disable WiFi on my three "i" devices no problem. Any thoughts on this?

My two iMacs frequently go offline when I have my iPad and two iPhones-5 connected with Airport Express (2nd edition). If I disable WiFi on my three "i" devices the offline problem stops. Any thoughts on this?

.....doesn't that seems to suggest the modem?
That is what I have suggested....twice now. From posts above:
My opinion would be that it is likely not the ISP, unless you have complete loss of Internet service for all devices at the same time......it is the Comtrend device....
and
I believe that the problem lies with the modem, and not the ISP signal.
Your ISP will likely have a different opinion, though. Please keep us posted on your progress.

Problem with Airport express N (2nd gen)

Problem with Airport express N (2nd gen)
Firmware 7.6.4
ISP - 20 Mbps ethernet cable
I have MacBook Air 13 mid 2013 os x 10.9.5, ipad 4 ios 8.0.2, ipad4 ios 7.1.2 , iphone 5 ios 7.1.1
When i try to use speedtest.net from my Macbook i got good results of download speed and incredible upload http://www.speedtest.net/my-result/3801286946 (connection 300 Mbps) , both ipads got terrible speedtest download result and incredible uploadhttp://www.speedtest.net/my-result/i/981631804 (connection 150 Mbps), iphone 5 got bad download and great uploadhttp://www.speedtest.net/my-result/i/981695357.
All these tests were done near airport express with really good signal and 5ghz. I tried to choose different channels, 802.11 mode, guest ssid, 5ghz ssid ...
I think that something is wrong with my new airport express. Can anyone help me to solve this problem?
ps sorry for my bad english

As a last resort, try a factory default reset on the AirPort Express as follows:
Power off the AirPort Express
Wait a minute
Hold in the reset button first, and keep holding it in for another 8-10 seconds while you simultaneously plug the Express back in to power
Release the reset button after the hold period and allow a full minute for the Express to restart to a slow, blinking amber light status
On an iPhone or iPad home screen....
Tap Settings
Tap WiFi
Look for a heading of Setup a New AirPort Base Station. If it appears.....
Tap on AirPort Express just below the heading to start the configuration process on the Express again
If you try several factory default resets, and the AirPort Express does not appear under the heading of Setup a New AirPort Base Station, the Express most likely is defective and will need to be replaced.

Mac OS X not working with Airport Express but Win XP is ok on the same iMac

Hello everyone,
as the message says I am having troubles with Airport Express.
To say it quickly, I live in a house share in London, and everyone in the house enjoys the wifi without troubles. I do as well with my macbook from every point of the house.
The troubles are with the big iMac: with mac os the internet signal won't just work at all, pages take minutes to load with both safari and firefox, and most of the times the loading times out.
I thought it was a signal power problem, but the weirdest thing of them all is that... when I switch to Windows XP on the same iMac (and right now I am writing from that!) the internet works perfectly!
Then I switch to mac os again... and slow internet again!
Anyone has an idea of what could this be?
Many thanks for the support

Yes, I just discovered this problem on my own machine.
I just wanted to check some settings and discovered that the behaviour of the GUI of Server Admin was somewhat "erratic": First this "no services are configured" message. Some of the configured servers were marked with the usual green "up and running" bullet, others dark grey - those were normally configured and running and clicking the appropriate line seemed to force Server Admin to check the actual state and then turned also green. But sometimes configuration pages were "greyed out", or while switching through the tabs Server Admin claimed that where were "unsaved changes" which should be saved (or discarded).
And then SMB: this was light grey, as usual when a service is not running and clicking on it I browsed through the configuration tabs - everything seemed ok (all my settings were correctly shown, configured as PDC with right domain name etc.) - and I started the service. Then suddenly the configuration settings changed to the default settings - no more PDC, but a "standalone server" with workgroup name "WORKGROUP"...
Looks for me, as if Server Admin lost it's "source" file for the configuration (the file in /var/db/smb.conf says, that it is automatically generated -- does somebody were the source file is stored?)...

Does airport extreme 802.11a/c work with airport express 802.11n

does airport extreme 802.11a/c work with airport express 802.11n

"You can use the AirPort Express to extend the signal provided by the new AirPort, but the Express will not extend "ac" wireless since it does not have that capability. The Express will extend an "n" wireless signal if that helps."
This is what I am trying to understand.
So AXTRM w/ sep SSID for 2.4 (b/g/n) - call it SSID1 - and 5GHz (ac) call it SSID2 - WiFi Explorer confirms AC mode on 5G.
Using an AXPRESS to extend - I have the option of SSID1 b/g/n *and* the 5GHz ac SSID2 in the pulldown (it sees both?) --> if I select SSID1, it also extends this same SSID in 5GHz (both showing b/g/n) >> so I now have 3 signals on SSID1 (XTRM 2.4G, XPRS 2.4G and XPRS 5G) b/g/n and one signal on SSID2 (XTRM 5G AC) ac
If I select the 5Ghz ac SSID2 to extend - it prompts me "do you also want to extend (the 2.4GHz SSID1)?" --> select yes and I now have 2 signals for SSID (XTRM 2.4G & XPRS 2.4G) b/g/n and 2 signals on SSID2 (XTRM 5G 802.11ac & XPRS 5G 802.11 a//n)
Is the 5G SSID2 actually being extended from the Airport Extreme to the Express?
The reason I bring this up is I am having a lot of issues since iOS8 came out (especially on iPhone 6). Everything I am reading is pointing to when people have 2 AP's set to use the same SSID. When you walk to a part of the house where 5G 802.11 ac signal marginalizes, the phone does not immediately hand over to the 5G 802.11 a/n Airport Express.
My thought was separate the SSID's but to me, if the Express can't extend 5Ghz from the Extreme, it's taking a step backwards. I am better off getting a more powerful router like an ASUS and going with one AP, drop the WiFi roaming altogether
Any thoughts?

Itouch with airport express?

Can you use the itouch with airport express. So you can play music from the itouch on your stereo?
That would be great!

Thanks for that!
Do I navigate to the Signal website via the Safari browser on my iTouch, and then install Signal onto the iTouch? Or do I install Signal onto my desktop Mac, open the app, and then navigate to the URL provided by Signal using Safari on the iTouch?
Kurt
*There is a cunning workaround!*
*Read this article:*
*http://lifehacker.com/software/hack-attack/remote-control-your-computer-with-you r-iphone-300762.php*
*Basically you run a web server application on your Mac (remember to open the ports in 'Sharing') it allows you to log in via Safari (on the iPhone or Touch or any browser) and remotely control iTunes, which of course can be connected to Airport Express.*
*I tried Signal last night and it's pretty impressive, I haven't tried the opensource application mentioned but will do later.*
*So you'll be remotely controlling iTunes, which will probably contain more music than your iPod.*

How do i use my time capsule and extend the network with airport express

I have a new iMac and Time Capsule, how do i extend the network with airport express. My time capsule does have a guest net work, and logins and passwords? I am no computer person. So for me it would have to be spelled out.

Use the search as this has been done to death ..
Bob Timmons is the expert on this.. look at his answers here.
https://discussions.apple.com/thread/4274187?start=0&tstart=0
https://discussions.apple.com/message/21856077#21856077
This has been automated in the v6 utility. I am used to doing it manually in v5 utility which is also fairly easy.
Apple doco is also good to read.
http://support.apple.com/kb/HT4145
http://support.apple.com/kb/HT4259
Note.
You cannot extend the guest network unless everything is up to date 7.6.3 firmware. And that is only with the TC as the main router in the network.
All apple routers can be configured as the main wireless or as the extend wireless.. so don't worry if a post uses express or extreme or TC.. they are for wireless, the same thing.

No signal with Airport express

Similar Messages

Maybe you are looking for