No sound after using Jensen iPad Dock

I used my new Jensen iPad dock with my iPhone 4S. After unplugging the iPhone it would no longer play music or allow text sounds when not connected to another device or though headphones. The volume control buttons on the side do not work properly, and the volume bar has completely disappeared from the music application. Also, when connected to a bluetooth device the options to choose music playback from the bluetooth device and iPhone speakers has changed. Instead if iPhone speakers it now says "Dock Connector". I know the iPad dock is the problem, but what is the solution?

had this a number of times to me even after using the charger it is dust or dirt in the charger plug of your phine or even in the earjack. depending on which you were using recently, use a photographes brush or i use an air ball for blowing the dust out do not blow in with your mouth the moisture corrodes things.
Essentially the dust gets pushed in there and the connectors think they are still connected, when using a dock especially if it hasnt been used for a while wipe the contact jack clean before using.

Similar Messages

IPhone5 has no sound after using bluetooth speaker?!

I have an iPhone 5 16gb with iOS 8.1.1 that I used last night with my LuguLake Portable Bluetooth Speaker to listen to music. I've used this particular bluetooth speaker for about 3 months.
I turned the bluetooth speaker off, like I always do, but the sound did not return to my phone. It has not made any sound since last night before I used it with the speaker.
I tried restarting the phone twice, using it with the bluetooth speaker again (works fine), tried it with headphones (works fine), but otherwise it acts like the mute switch is on - and its not. I've even tried restoring the phone and it didn't make any noise, so I restored my backup, still no noise... What do I do?!!!!!
I have an otterbox case on my phone and do not recall dropping it recently. I never use the headphone port so it's not dirty but I cleaned it with a q-tip just for good measure. I don't know what else to try.
It seems like the phone won't disconnect from the bluetooth speaker even with bluetooth off.
Please help!

Hey fashionablewife,
Great troubleshooting! I know how frustrating it may be if an iPhone doesn’t operate as expected. But, it sounds like you have almost exhausted all of the troubleshooting steps outlined in the following resource. If so, you can follow the link at the end to contact Apple Support. Otherwise, definitely give the steps another go:
If you hear no sound or distorted sound from your iPhone, iPad, or iPod touch speaker - Apple Support
http://support.apple.com/en-us/ts5180
Thanks,
Matt M.

No sound after using isquint

I've had a lot of success using isquint converting movies to ipod. But I converted a VCD movie somone gave me and it worked fine. I played in quicktime with no problems after converting it to MP4. But once I transfer it to my ipod I get no sound after the first 10 seconds. Also one other problem. I have an mpg movie I converted over to mp4 in isquint but it toally distorted the orientation to a vertical format. any ideas?

it's not software related the fact that it happened after ios7 is random
it's a hardware issue
read more here
https://discussions.apple.com/thread/1343532?start=315&tstart=0
read more here
https://www.google.dk/search?client=opera&q=iphone+stuck+in+headphone+mode&sourc eid=opera&ie=UTF-8&oe=UTF-8

Charging device fails after use on iPad mini

I have several apple devices that require the lightening charging cable. Every cord that I use on my mini fails shortly after use. These are OEM cords that have been used with no issues until plugged into the mini. It appears that it is the usb / lightening cable that fails as the wall charger will still work with other cables / devices. I've had 4 chargers fail so far and have now banned charging of the mini.... any suggestions?

You didn't mention which reset you tried that didn't work ...
Try this reset ...
Tap Settings > General > Reset > Reset All Settings
Then restart your iPad.
Try the iTunes Store.
No data is lost due to a reset.

Can I use my iPad dock with 3rd gen iPad?

I already have an iPad 2 dock. Can I use this for my 3rd gen iPad?

Hi Capp 543:
I don't really use it any more live, mainly because I use my iPad for reading music and don't want to switch around apps. I'm not part of the company, but I'll try.
IMO the iRig manual is way way too simplistic.
I am attaching some jpeg's of what helped me solve it, though it was tough. If it doesn't open, search Audio Midi Setup help for "sharing midi data over a network". You have to create a wireless session using Audio/Midi setup, OR create an "ad hoc" network using bluetooth if there's no wi-fi (another set of problems...). This may be your issue. There are a few things beyond getting the wireless network appearing that you have to do, that's why I'm suggesting this even though you did it, or a part of it.
In particular:
"Anyone" has to be set as who can connect to me in the lower left of the wireless midi setup screen, and
First get everything else ready, meaning the iPad connecting, THEN LiveRig has to be launched from closed, meaning do an icon hold and close in down iPad, then open it up for it to connect, when everything else is ready. for some reason that helped me.
In MainStage, you of course need to go to the MainStage #1 Setup screen, drag in sliders, then "learn" them to the LiveRig, which should now be seen when you click "learn" and move a Liverig slider. I have a vague recollection about not seeing iRig in the MainStage #1 top left device window, but then going into the drop-down menu there where the device shoudl be, selecting it, then learning the sliders. Then in the #2 Edit window you assign the sliders etc.
I would suggest first connecting it via midi wires and getting it to work, which will help you decide if a problem is in the wi-fi or somewhere else when you go to connect it up with wi-fi. You'd need the Apple Camera Connection kit adaptor. I myself would alway run it via midi if I'm playing live, too many unknowns with unknown networks.
Hope that helps.
Neil

Play music while charge using Apple iPad Dock

I connected the Apple iPad Dock to my Bose SoundDock through the dock's line out and it only plays music if the charger is not connected to the dock. when i connect the charger to the dock the music stops and start being played on iPad. is it right or my dock is damaged?
thx in advance.

Press the Music In ... to the left of "Albums" at the bottom of the Remote App and select a different library to show in the app. That seems to do it.

My ipad won't turn on. Have tried to reset by pressing the two button at the same time. It work. Why is this happening? For the first time it happened to me after using the ipad 4 running on ios 7, for almost a year and a halftime

My ipad won't turn on. Tried to reset and it work. I'm using ipad 4 with ios 7 and this is the first time that this happened to me.what is wrong with the ipad?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Centro has no sound after using headphones

Hi, all. I used a 2.5 mm jack (radio shack adapter) so I could used my good quality headphones and listen to mp3 music. After removing this, my Centro had no volume when making calls and people on other end couldn't hear me either. The common fix for this (wiggling a pin inside the 2.5 mm female jack of the phone) did correct this. But I won't do this every time I want to listen to mp 3.
So, why did this happen? Is there a specific type of 2.5 mm jack, or is this a phone defect (ie: a pin inside the female end of the jack sticking)? Is this a common issue? Is there a permanent fix?
Post relates to: Centro (AT&T)

This issue has been reported on Treo model phones. It sounds like the microswitch in the headset jack is sticking.
What you have done is similar to the procedure supplied in the kb.palm.com article regarding the headset jack issue.
Here are the steps for trying to resolve the issue.
Plug and unplug: Try plugging and unplugging the headset to the smartphone a couple of times. The smartphone might mistakenly be under the impression that a headset is plugged into the phone, which would make it route audio to a nonexistent headset.
Clean the jack: If there is contamination or debris stuck in the audio jack, the speaker, microphone or headset may not work properly. Visually inspect the jack for debris that could block the connection. Try inserting and removing the handsfree headset a couple of times to see if it clears the debris from the device. You can blow into the jack or use gentle compressed air to clear debris. Note: Be cautious in using foreign objects to clear the jack. Like your ear canal, the headset jack is a delicate space that can be damaged if you clean it improperly.
Where's the trouble? If the steps above didn't help, you may need to contact Palm for further troubleshooting. An agent can walk you through a process to determine whether a particular component is failing, and whether the device needs repair.
I would suggest using a non-conductive electrical contact cleaner (you can find this in the electrical dept. at Home depot or hardware stores), spray it on plug of your headphones, insert and remove the plug several times to try and clean the jack.
For reference purposes, click on the following link for the support page for your device on the kb.palm.com webpage.
http://kb.palm.com/wps/portal/kb/na/centro/centro/att/home/page_en.html
There are links on the page to the user guide, troubleshooting, how to's, downloads, etc.

No sound after using headphones to watch a netflix movie

I am looking for help to resolve my no sound issue. I can hear sound with headphones but not from computer speakers. Help????? I have tried going into itunes and using the headphones and unplugging them. I have gone to system preferences and I am getting a message that states the selected device has no output controls..... any ideas????

it's not software related the fact that it happened after ios7 is random
it's a hardware issue
read more here
https://discussions.apple.com/thread/1343532?start=315&tstart=0
read more here
https://www.google.dk/search?client=opera&q=iphone+stuck+in+headphone+mode&sourc eid=opera&ie=UTF-8&oe=UTF-8

I am after using my ipad for 2-3 hours to record video, it will be while traveling so I could do with being able to set it up so it just records while I drive. Is this possible?

Hello as stated I wondered if there is an app that I could use to record a journey that I will make, it will take aprox 3 hours I can charge my ipad up as I go so battery life is not a problem and I have quite a bit of room on my I pad. Is it possible?

Sure why not. The camera app will record videos and there are car chargers for the iPad that you can purchase. You will need some sort of stand to place the iPad into, but those are available as well. You might need to adapt the out of the box car stands to face in the direction that you want, but there are lots of them out there.
You should set the iPad to not go to sleep in Settings>General>Auto Lock>Never until you are done recording.
Car chargers
https://www.google.com/search?q=car%20charger%20for%20iPad%202
Car Stands
https://www.google.com/search?q=iPad%20car%20stands%20
Sorry, I just realized that you have a charger.
Message was edited by: Demo

No sound after using the ear phones

i was watching you tube video using the ear phone. when to to do something cam back no sound. with or without ear phones. i am not very technial so n idea what to do as i am in Fiji on holidays.

If there is a red light in the audio output port, insert the earphone plug a few time to see if you can trip the internal switch. If that fails, insert a cocktail stirrer or the like and jiggle inside in order to trip the switch. If that fails, go to a repair facility and have them trip the switch.
Ciao.

HT201205 no sound after using blue tooth with iphone 5

I have just purchased a 2014 Durango and the Blue Tooth works fine with my Iphone 5. However, after i leave the vehicle, i have no sound on my phone. Have tried to restart, turned the blue tooth off, tried playing both a song and a movie to no avail. Any suggestions?

It sounds like it is still connected.
Try disconnecting it here:
Settings > Bluetooth > Select the Durango and disconnect.
If that does not work:
Reset: Hold the Sleep/Wake and Home buttons and don’t let go until the screen goes dark and the Apple logo appears (no data will be lost)

No sound after using quicktime pro???

I converted a video and added it to itunes but it played with no sound. Please help i bet there is a stuipid mistake im making here im pretty mad that i just spent 30 dollars on quicktime pro only to have problems.

This is normal if your source file is a "muxed" audio/video data stream. Use an MPEG based converter for these type files.

No sound after using DVD Decrypter and Videora

Last night I used DVD decrypter to rip Fight Club and then used Videora to covert the .vob file to MPEG-4, following the directions on the Videora website. I loaded into iTunes, and then onto my iPod, but the sound doesn't work at all even though the video looks great. I have converted two .avi files with videora and I've had no problem watching them on my iPod. I did notice that the instructions on the videora site said to only select the top movie in the list that has all the 2 channel and 6 channel files. The movie plays in iTunes with no sound as well. Anyone have any ideas?

OK, I am an idiot. I only selected the video and forgot the 6 channel audio.
Note for future people with this problem:
Don't just select the first file in the list under stream processing like Videora's website says. You also need to select an audio file to rip and from what I'm hearing, to avoid problems, select the 6 CH audio.

4S (iOS7) lost its sound after using AirPlay :-(

Apretiate any suggestion.

Hello FHFM,
I'd suggest restarting your iPhone, and then a reset, should restarting fail to resolve the issue.
iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting
http://support.apple.com/kb/HT1430
If your sound still hasn't returned, I would recommend restoring the device.
iTunes: Restoring iOS software
http://support.apple.com/kb/HT1414
All the best,
Allen

No sound after using Jensen iPad Dock

Similar Messages

Maybe you are looking for