No sound from new soundcard

I have installed a new Diamond Xtreme Sound 7.1/ 24 bit sound card in my system. I get all of my regular computer sounds, and Windows Media Player works, but iTunes acts like it is working, but no sound is heard.

Hi warres1,
Try the general tips in this article: http://support.apple.com/kb/TS1362
-Jason

Similar Messages

  • No sound from new device

    hi
    just bought a new x-fi xtreme but i'm getting no sound from it at all.
    in device manager it sees it working and no problems.
    latest drivers are installed & old drivers uninstalled.
    under the windows sound mixer which sits on my taskbar, it has cross through the speaker, and if i click it to open the mixer, it says "no audio device is installed" even though if i hover over the icon, it will show SB X-Fi Xtreme Audio & volume at 0.
    if i open the creative volume panel, the volume control is at 0 and greyed out.
    when i run the diagnostics tests i get these results:
    LogCreative Diagnostics Test Log
    Detected device:
    SB X-Fi Xtreme Audio
    Tested device:SB X-Fi Xtreme Audio
    2/28/2009 08:25:04PM Drivers Tests Pass
    2/28/2009 08:25:05PM Windows Multimedia Tests Pass
    2/28/2009 08:25:05PM DirectSound Tests Fail.
    i have my speakers connected to line 2(green) & headphones connected to line 3.
    anyone know what could be causing this?

    never mind, i took it back and got my money back, bought a xonar instead...which works perfect
    thanks for the no help creative

  • Sound from new MSI R9 280X - coil whine? RMA?

    Hey all.
    Just trying to determine if the sounds coming from my new PC's video card are normal or not. Here is my build: au.pcpartpicker.com/p/1XKQb
    I hear this sound when running what I would consider low end graphics tests as well as when I booted up BF4 for the first time last night.  Graphics automatically set to high.
    I've recorded a few sounds of the 'squeals' that I hope are good enough for people to make a judgement. The sound seems to be coming from the part of the video card where the power connects. I have reseated the card and tried using a different power cable. It is not an issue with the fans.
    First is a capture from a test in Unigine Valley:
    soundcloud.com/angryeye/sounds-from-friday-evening
    Second is a sound from loading Team Fortress 2 and then moving the mouse a little bit.
    soundcloud.com/angryeye/sounds-from-friday-evening-1
    Interestingly, when I enable Vsync in Team Fortress 2 the sound disappears. If I enable Vysnc in the Unigine Valley test, it does not make a difference.
    I also ran a test in the 3D Mark(did not have the option to change anything as it is only a demo) and the Ice Storm made the worst sounds from the card:
    soundcloud.com/angryeye/ice-storm
    soundcloud.com/angryeye/ice-storm-2
    Considering buying 3DMark so I can muck around with the settings a bit and see which cases I hear the sound and which i don’t
    I also loaded up BF4 last night and got the noise with VSYNC enabled or disabled(can record if needed). Also the same issue in Deus Ex, makes sounds with Vysnc on and off.
    Can anyone with a MSI R9 280x confirm if this is normal? Is this coil whine? Reviews on newegg seem to indicate a lot of people are getting similar sounds and I’m not really thrilled with this considering it’s a brand new card and the first time I've built and i can hear this through the case and fans.
    Could it be something that can be fixed by modifying voltage settings (as it seems to come from the power connection)? Or does this require an RMA?
    Any advice appreciated.

    so your parts are:
    CPU: Intel Core i5-4670K 3.4GHz Quad-Core Processor
    Motherboard: MSI Z87-G45 Gaming ATX LGA1150 Motherboard
    Memory: G.Skill Ripjaws X Series 8GB (2 x 4GB) DDR3-1600 Memory
    Storage: Samsung 840 Series 250GB 2.5" Solid State Disk         
    Video Card: MSI Radeon R9 280X 3GB Video Card
    Case: Cooler Master HAF XM (Black) ATX Mid Tower Case                            
    Power Supply: Antec HCG M 750W 80 PLUS Bronze Certified ATX12V Power Supply
    Operating System: Microsoft Windows 8.1 Pro - OEM (64-bit)
    ok there are 2 causes of coil whine and odd noises so be totally sure its coming from the Graphics card itself by getting your mike directly over it and move it around and test other parts for noise as sometimes its The PSU (Power Supply Unit) that is doing it or it can cause it as yours is a split +12v unit (+12V1@40A, +12V2@40A) it may be the cause as Antec at times do not make reliable units (those rating is has for 2 rails look to me as being fake as they exceed its power limits combined (12v x 80A = 960W so it can probably do 40A on one but then the other will be terrible at 22.5A as it looks like there doing virtual +12v rails with 40A OCP fuses)) so its suspect as it may not be behaving well!

  • Capturing sound from the soundcard

    Hello,
    Does Audition make it possible to capture the sound from the sound card?
    I don't want to record a sound using a microphone, I want to save the sound which is played on the sound card.
    Regards

    Assumption: You are trying to record using the internal sound card in your computer.
    Right click on the speaker in the task bar (normally lower right of the screen).
    Select "Open Volume Control".
    In the "Volume Control" application in the menu select "Properties" from the "Options" menu.
    Click on the "Recording" radio button and hit "OK".
    This will bring you to the "Recording Control" dialog box. Check the
    "Stereo Mix" radio button.
    On most computers this will change input for Audition v3 to listen to the output of the sound card.
    Note1: Make sure you are using "ASIO4ALL" or "Audition 3.0 Windows Sound" or you won't hear or record anything because two applications can't use most standard ASIO sound drivers at the same time.
    Note2: Make sure you change it back to "Microphone" or you won't be able to record using the computers internal sound card.

  • No sound from new speakers

    We got a set of bose speakers, plugged everything in as instructed but there is no sound coming from the cable box.  Got a new cable box and hdmi cable, still no sound.  The bluray works great.  What gives?

    Since the Bose Cinemate Series II speaker system has only one usable active digital input.... the easiest way to have both the Blu-ray player and the cable box playing in the Bose without having to keep switching the optical cable back and forth between the two sources, is to have both of those devices hooked into the HDMI inputs on the TV and just have the Bose's optical cable running from the optical out on the TV into the optical input on the Bose.

  • No sound from new Viewsonic monitor

    I just got a new mini--hooked it up to the Viewsonic VA1930wm monitor and no sound comes from the monitor. When I go into the sound preferences--it doesn't seem to see it. The mini itself has sound--but I want it to come from the monitor. There are no drivers available..am I doing something wrong?--or should I get a different monitor--and if so--which one?
    Marilyn

    Welcome to Apple Discussions!
    Most monitors with audio have an audio in 1/8th inch input jack to run a cable between the monitor and the computer's sound output jack. Usually it comes supplied with a cable to go between the computer and the monitor that fits that jack. If your monitor was missing such a cable, you can buy it at Radio Shack. Look at the under side or back of the monitor for where the video cable comes in. Somewhere near there should be the audio jack. If there are multiple, you may need to split the channels coming out of the stereo built-in to the back of the Mac Mini. Which Mac Mini model do you have? Is it an Intel or PowerPC?

  • No sound from new computer

    I purchased a HP Pavillion a6700f  with Vista last month and tried to hook up my four year old self powered Boston Acoustic 735 digital speakers to it.  It uses a single analog line that I plugged into the green jack on the back of the computer as indicated in the instructions.  No joy.  I updated the Realtek driver and still no success.  I took the speakers into work and plugged them into the HP there (using xp) and they work fine.  After three hours of the India tech guys taking control of my system, I was informed that Vista does not support speakers that worked on the XP operating system and I would have to buy a new set (which he was only too happy to sell to me at that time).  Supposedly there is a tech report that speaks to this issue, but the tech guy could not provide me with a number or web address for it.  I have had no success finding it.  Does anyone know if this is true?  If not, any clues on what other options I have?

    OK. First make sure you those the kind of speakers that need to be powered via the power adapter and that you have a green audio plug. The orange connector used in older models don't have that port needed on any new pc anymore.
    I call bullcrap (excuse my language, but can't keep quite to a such a Tech's comments, being a technician myself) that you need to get "vista" speakers. There's no such thing as XP speakers or Vista speakers. Speakers don't need drivers and are not related to the Operating System any way way, shape or form. All you do is power them and plug them in depending on your configuration.
    Make sure they're plugged in the back of the computer via the greem front audio output color coated port and make sure they are turned on and that the volume isn't muted.
    Then in Vista, login the pc, look on the bottom right of the comuter screen next to your clock, there's a white speaker icon. Just go with the mouse over it and it should say this:
    Volume xxx
    Speakers
    Realtek Digital xxxxxxxxx
    If instead of speakers it says HDMI Output or Realtek Digital Output then it's set to the wrong playback device. So rightclick on that white speaker icon, choose Playback Devices and when the new windows comes up look in the middle. It should say Speakers, Enabled, Working. Also make sure it has the green check mark on it.
    If it doesn't rightclick on the grey speakers picture and choose Set as Default Device and then Apply or OK and restart the pc.
    Also on the top choose the Sounds tab and make sure it says Windows Default sound scheme and also check the voume and make sure it's not muted or low.
    Best of luck.

  • Muffled sound from new imported CD

    It started with cds with small scratches on them that were poor quality. Now even the brand new cds that get imported have parts of the song that are distorted. Its not all through the song , just sertain bits.

    Are you using AAC or MP3? And at what bit rate?
    Also, try burning a CD using a different codec like WMP or LAME. Then add folder to iTunes. Do you get the same result?
    HTH

  • Unable to get sound from new ATV installation using either HDMI or optical audio to Bose receiver.  Good video using HDMI.

    Need help setting up my Apple TV.  I have good video, but no audio using either the HDMI cable by itself or by connecting a optical video cable through the aux receiver for home theater.  I've replaced the Apple TV box, swapped out HDMI cables, reset the Apple TV box, all to no avail.  Any suggestions?  Thanks

    Connected only using HDMI to Onkyo Receiver and HDMI out to Samsung 1080p TV. So far so good.

  • When I select a sound email or video, decide I want to go to another video or email, the sound from the first video continues to completion before I can listen to my new selection. How can I stop this?

    How do I stop the sound from a video or email when I want I click out of the video. Presently, the sound continues and I have to escape out to home screen to stop it.

    Now as you may know there is some icons at the bottom of the mail app, at the top left conner you should have the inbox button and on the upper right conner you should have two arrows to shift between emails. If any of those options works try :
    Settings>General>Reset>Reset all Settings
    If that does not work try to re add the account
    Last but not least, restore as new.
    Hope that helps.

  • I recently got new mac air and transferred my old version garageband projects now when I open them in 10.0.2 I can add new tracks but then nothing can record, shows its receiving sound from software inst. but no sound. I checked audio preferences and

    i recently got new mac air and transferred my old version garageband projects now when I open them in 10.0.2 I can add new tracks but then nothing can record, shows its receiving sound from software inst. but no sound. I checked audio preferences and they are set as they should be. I tried it in all the other older projects and same issue anyone have any experience like this very frustrating.  Can one download old version still ? or can you run both versions on OS10.9.5 ?

    Ok, either my question was too long or nobody seems to have an answer. Sad, either way
    Here's something I found out in the meantime, maybe this is interesting for somebody or maybe - problem's not totally solved - enough info for any of you to give me further advice.
    When I start Logic Core Audio driver de-activated, I can open old songs. Then I save them in a new folder with all audio files and a new name. And I remove all EXS24 instruments as well as the Space Designer. I quit Logic, re-open with Core Audio activated and I can open the song.
    Problem no.1: EXS24 instruments don't find the appropriate samples, but EXSMananger Pro did help me with this. Same problem with Space Designer, which doesn't find the impulse responses, connected to a certain preset.
    Two questions, every idea would be great!
    - Is there any way to teach Space Designer Presets where to look for impulse respones. I can load IR samples directly and create a new preset, but I can't use my old ones.
    - Is it possible to install Logic from scratch over an existing version? Or how should I de-install everything connected with Logic and then install a fresh version from CD?
    Thank you again,
    Joern

  • I recently got new mac air and transfered my old version garageband projects now when I open them in 10.0.2 I can add new tracks but then nothing can record shows its recieving sound from software inst. but no sound. I checked audio preferences OK

    i recently got new mac air and transferred my old version garageband projects now when I open them in 10.0.2 I can add new tracks but then nothing can record, shows its receiving sound from software inst. but no sound. I checked audio preferences and they are set as they should be. I tried it in all the other older projects and same issue anyone have any experience like this very frustrating.  Can one download old version still ?
    thanks,

    Ok, either my question was too long or nobody seems to have an answer. Sad, either way
    Here's something I found out in the meantime, maybe this is interesting for somebody or maybe - problem's not totally solved - enough info for any of you to give me further advice.
    When I start Logic Core Audio driver de-activated, I can open old songs. Then I save them in a new folder with all audio files and a new name. And I remove all EXS24 instruments as well as the Space Designer. I quit Logic, re-open with Core Audio activated and I can open the song.
    Problem no.1: EXS24 instruments don't find the appropriate samples, but EXSMananger Pro did help me with this. Same problem with Space Designer, which doesn't find the impulse responses, connected to a certain preset.
    Two questions, every idea would be great!
    - Is there any way to teach Space Designer Presets where to look for impulse respones. I can load IR samples directly and create a new preset, but I can't use my old ones.
    - Is it possible to install Logic from scratch over an existing version? Or how should I de-install everything connected with Logic and then install a fresh version from CD?
    Thank you again,
    Joern

  • No sound from optical on NEW SkyHD+ box

    Hi all, I've read a few posts already about this issue and I like many others cannot get surround sound from the Sky box via OPTICAL cable to my Pioneer surround sound amp system. The SkyHD+ box is brand new so was forced to buy an optical cable to link to my Pioneer AXD 7305 system. The Pioneer plays the  5.1 sound via blu ray no problem using Coaxal but as try as I may I cannot get the Sky box to deliver surround sound using optical.  My set up is: Panasonic TXP42G20B TV linked to SkyHD box via HDMI cableSky box Sound Settings set to "Dolby D" for both Digital Audio AND Digital HDMISky Box connected to Pioneer AXD 7305 via NEW optical cable from OPTICAL OUT on Sky boxPioneer AXD 7305 set to "Video 1 OPTICAL input" I rang Sky Support & they just suggested the sound settings set to "Dolby D" which I have done. Please help if you can.

    You may have tried it but have you set the sound settings to NORMAL. Mine is connected by optical to a soundbar and works with both settings.

  • Re: New X230T: Weird sound from the fan when it accelerates

    http://forums.lenovo.com/t5/X-Series-Tablet-ThinkPad-Laptops/New-X230T-Weird-sound-from-the-fan-when...
    Dear moderator andyP,
    the above post was ment to be a standalone post so it could get some more attentions by the Lenovo associated guys so they would see my wish and maybe do bios update! So i don't thank you for moving!!! 
    Regards,
    achim1989
    Moderator Note; included link to relevant post
    Using x230t (i5-3320M, 8GB RAM, 256GB SSD, 80GB mSata-SSD) and loving it!
    "I may not own the world but I own my mind and therefore the world is at my feets." (me)

    Please re-read the forum guidelines, it states clearly;
    "Before creating a new thread, search the appropriate section of the forum first for any existing and related threads. It may be more constructive to all, to advance the knowledge of an existing thread than to create a possibly redundant one."
    Thread locked
    Andy  ______________________________________
    Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
    Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество
    PepperonI blog 

  • Only sound from my right internal speaker on my new hp stream X360 PC 11

    hi, just opend my new HP Stream X360 PC 11 and it´s only sound from my right internal speaker. the system is updated and ive done the soundtest and the sound comes thru the right speaker even when i push the left speker test button.... softwere or back to the shop...  

    Were you able to contact Apple, about this issue, while under warranty?
    If there is a hardware cause of the problem or other, they may fix it or
    at least diagnose the underlying cause...
    Your other post was changed into a new thread on its own, here:
    •Popping sound from right MacBook Pro speaker
    When posting in an old topic, your issue may not relate to the original
    cause of the problem someone had a year ago with different hardware
    and another build version of OS X.
    Good luck & happy computing!

Maybe you are looking for