No sound front panel audio with newest CMI 9880L driver

So basically I plugged in a headphone the other day on the front panel and noticed the audio jack randomly stopped working. They worked for about 3 years and the last changes I've made was updating the CMI 9880L driver to the newest one on the MSI website for my mainboard( 915P combo), about a month ago. So I thought the problem was the new driver, I went back to the CD that came with the board and installed the audio drivers I had before, It also didnt work!. I went to the hardware manager and clicked on the ROLL BACK driver button and it installed a microsoft driver, this time the front audio jacks DID work, this means is not a hardware problem. What is going on with the new C-MEDIA driver? what should I do to restore sound to the front jacks?
ps. I messed around with the BIOS options(switching between Azalia and AC97) and nothing happened.

Quote from: ivon on 26-September-06, 21:14:20
I am quite confused... would appreciate your help.
Well, so was I. A good explanation can be found at
http://www.intel.com/support/motherboards/desktop/sb/cs-015851.htm
The point is, that the same output can be used either for AC-97 front panel audio (what you have on your chassis) or for High Definition Audio (which I've never seen). The board seems to differentiate between these two by means of the PIN #4 (Presence), which you just leave disconnected in your case.
Microphone should use PINs 1, 2 and 3:
1 - Mic In, 2 - Ground, 3 - Mic Power
Audio output should use PINs 5, 6, 9 and 10:
5 - R-Out, 6 - R-RET, 9 - L-Out, 10 - L-RET.
After you'll have connected the PINs to the audio connectors, do not forget to turn off the jack detection in the "Realtek HD Audio Manager" as I described before.

Similar Messages

P35 Platinum front panel audio with Antec P180 case?

God I have a headache after reading all those "front panel audio" threads. Why can't mb's all use the same freaking pinouts!!!!
The case doesn't have a HD front panel.
MB pinouts are:
1. Mic_L (MIC Left Channel)
2. GND
3. MIC_R (MIC Right Channel)
4. PRESENCE#
5. LINEout_R (analog port right channel)
6. MIC_JD (MIC jack detect)
7. Front_JD
8. NC (empty)
9. LINEout_L (analog port left channel)
10. LINEout_JD
Case Front Panel connector is a preconfigured block with pigtails hanging off in case it doesn't match up.
1. MIC Signal
2. MIC Power (MIC BIAS)
3. Ground
4. FPOUT-R (front right)
5. FPOUT-L (front left)
6. RET-R (rear right)
7. RET-R (rear left)
glaring differences are the ground and the MIC connectors.
How do I connect these? I don't want to fry anything.
Thanks.

They do have the same pinouts. There are two standards is the reason for two different pinouts. It's just that your MB is Intel HD and your case is AC-97.
For Intel® High Definition Front Panel Audio
Pin Signal Name Description
1 PORT 1L Analog Port 1 - left channel (Microphone)
2 GND Ground
3 PORT 1R Analog Port 1 - right channel (Microphone)
4 PRESENCE# Active low signal that signals BIOS that an Intel® HD Audio dongle is connected to the analog header. PRESENCE# = 0 when an Intel® HD Audio dongle is connected
5 PORT 2R Analog Port 2 - right channel (Headphone)
6 SENSE1_RETURN Jack detection return for front panel (JACK1)
7 SENSE_SEND Jack detection sense line from the Intel® HD Audio CODEC jack detection resistor network
8 KEY Connector key
9 PORT 2L Analog Port 2 - left channel (Headphone)
10 SENSE2_RETURN Jack detection return for front panel (JACK2)
For AC-97 Front Panel Audio
Pin Signal Name Description
1 MIC Front panel microphone input signal (biased when supporting stereo microphone)
2 AUD_GND Ground used by analog
3 MIC_BIAS Microphone power / additional MIC input for stereo microphone support
4 AUD_GND Ground used by analog audio circuits
5 FP_OUT_R Right channel audio signal to front panel (headphone drive capable)
6 FP_RETURN_R Right channel audio signal return from front panel (when headphones unplugged)
7 AUD_5V Filtered +5 V used by analog audio circuits
8 KEY No pin
9 FP_OUT_L Left channel audio signal to front panel (headphone drive capable)
10 FP_RETURN_L Left channel audio signal return from front panel (when headphones unplugged)

Using Front Panel Audio with Fatality Professional

I have a query regarding connections on the Titanium Fatality PCIe.
I have an XFi XtremeMusic PCI card and am considering replacing it with the Titanium Fatality XFi card. A couple of reasons, I like the shrouded enclosure, I like the little XFi LED logo, I want to move away from PCI cards in my system.
But one of the main reasons is to allow me to connect my Intel HD Audio connector to the card so I can use the Headphone/Mic socket on my case. So if anyone has these cards can they confirm that they have an Intel HD Audio connector on them. If so does connecting the headphone to the case socket mute the speakers?
Cheers

Well, I don't personally have one, but I was under the impression that every X-Fi had one. I know my X-Fi Fatal1ty (original PCI version) included it, and my Recon3D definitely does.
Plus if you check their shop website for the Titanium Fatal1ty Professional than the specs page lists a 2x 5-pin connector for "Intel HD Audio Compatible Front Panel Header" so it most likely does.
I would assume it would mute the speakers only if your case is fully Azalia compliant. By that, I mean the standard (as dictated by Intel) involves the use of two normally-open switches - one each on the headphone and microphone jack - which are closed as a result of plugging something into them. Some cases have these jacks which means it can detect when you plug something in and respond accordingly, but others use cheaper (we're talking differences in cents - not exactly substantial savings, but when you do it thousands of times over it adds up) switchless jacks and simply report them as always plugged in.
Just remember to set up the X-Fi panels to mute the speakers when you plug headphones in, as well as switch the output to headphone mode. You can actually set those two options separately on X-Fis.

Front panel audio jack is not working on K9N Neo V2

My front panel audio jack is not working on K9N Neo V2. I check the JAUD1 cable and it appears to be connected to the front panel audio jack. My soundcard driver cannot detect any gadgets when I plug it in the front panel. My audio drivers and BIOS are up to date. Is there any known solution to this? My computer is only a few months old and I have not tried the front audio jack until recently. I'm on Vista home premium btw.
Also, I've got another problem, my processor is AMD 64x2 4400+ overclocked to 2.63Ghz. I've been using that clock value ever since I built this computer and stress tested the processor and found that it would not cause any problems like hanging or overheating. However, I recently decided the need for AMD's Cool & Quiet technology and enabled it. It caused BSODs every few days or per week that didn't happen before. I tried it with the default clock value and it still causes BSODs. Can someone help me?

Quote
Thanks. Its ironic that disabling it actually enables it.
It has to day with the front panel audio wiring of your case. How many wires are there that can be connected to the board's pin header?
Quote
Sound quality isn't very good
Can you be more descriptive? Is the quality better if you plug the headphone into one of the jack at the back panel? (Also, make sure you tell the Realtek HD Audio Manager, that a headphone is connected (and not regular speakers).

Does Front Panel Audio Work When Using RCA Outputs from the X-Fi Titanium HD PCIe Sound Card?

I see that the rear panel headphone output is disabled when the soundcard RCA jacks are used.
But is it possible to have the front panel audio output work at the same time that the RCA jacks are in use or is it also disabled?
I am willing to tolerate inferior quality audio feeding my monitor and use the RCA jacks for my headphone amp.

I was able to construct a work around for this problem. A Y splitter from the RCA outputs is an option but can degrade the sound because of the uneven load presented to the soundcard.
Ten eleven inch Apevia CVTAUDIOE25 HD Audio extension cables were connected together in series to a SilverStone FP32 3.5 audio front panel bay. The extension cables were connected to the front panel audio connectors on the Titanium HD sound card and then the cables were run out of the computer case and up to the area near my keyboard. I connected the front panel audio bay to the extension cable and the bay sits next to the keyboard. When no 3.5 mm stereo cable is connected to the front bay near the keyboard the sound is normal out of the rear outputs. But when a 3.5 mm audio cable is plugged into the front panel bay audio there is sound out of the SilverStone front panel bay. The sound is still muted out of the rear RCA jacks when the plug is put in the front bay but it is only used when the main audio outputs are not required.
The function for me is that the front bay serves the same purpose that the previous front panel 3.5 mm audio extension cable did.
There are photos of this under a different user name on Audio Asylum PC Audio.

Help with front panel audio on K9N board.

Okay, I admit I'm a bit of a moron with front panel audio but I just can't figure out how to configure this board with my case. Here are the pins:
Case:
Mic In
Mic Bias
SpeakOut L
Return L
SpeakOut R
Return R
Ground
Motherboard:
PIN    SIGNAL      DESCRIPTION
1    PORT 1L      Analog Port 1 -Left channel
2    GND      Ground
3    PORT 1R      Analog Port 1 -Right channel
4    PRESENCE#     Active low signal -signals BIOS that a High Definition Audio dongle is connected to the analog header. PRESENCE# = 0 when a High Definition Audio dongle is connected.
5    PORT 2R      Analog Port 2 -Right channel
6    SENSE1_RETIRN     Jack detection return from frontpanel JACK1
7    SENSE_SEND     Jack detectionsenselinefrom the High Definition Audio CODEC jack detection resistor network
8    KEY      ConnectorKey
9    PORT 2L      Analog Port 2 -Left channel
10    SENSE2_RETIRN     Jack detection return from frontpanel JACK2
I haven't been able to make any sense of the two, so if anyone here can help, I would appreciate it very much.

Quote from: crazy on 09-June-06, 15:51:46
You may tell us more information about your mainboard, please give us the detailed name of your mainboard. :D Then there will be more users could give some suggestions.
Sorry, there aren't that many K9N boards out there, but mine is the K9N Platinum MS7250 Version 1.0. It's the AM2 non-SLI nVidia nForce 570 Chipset model.
Thanks for any help.

Sound Blaster X-Fi XtremeGamer Fatal1ty Professional and front panel audio compatabai

I recently purchased a XtremeGamer Fatalty Professional and was wondering if i could connect the front panel audio from my thermaltake case to it

Well, I don't believe that to be possible. I don't think Creative has ever put out pinouts for the cards. And I have a hunch that none of the pins carry analog audio through them (correct me if I'm wrong though).

Help RE:Front Panel Audio and Sound Blaster Live! 24 Bit C

I own Soundblaster Li've! 24-bit card.
I would like to make use of the front panel audio jacks on my case but i have no idea where on the card to connect the pins on the card ( the pins are:Mic In, Mic Power, Ear R, Ear R, Ear L, Ear L, GND)
Anyone know where exactly do each of these pins go?

Maybe this site can give some light on this matter - http://audigy2zshowto.blogspot.com/
jutapa

MSI P965 Platinum - Front Panel Audio u/s

Finally after managing to get XP Pro SP1 CD to install, I have a stable system, and thanks to those whom freely gave advice.
But we hit the next issue with this motherboard, the front panel audio.
Firstly the Realtek detection software doesn't detect anything plugged into the front panel.
Connected the cables as follows from my Coolermaster Stacker case;
mobo = case wires/colour
pin1 aud-mic = mic-in - yellow
pin2 aug-gnd = gnd - black
pin3 aud-mc-bas = mic-pwr - red
pin4 aud-vcc = empty
pin5 aud-fpout-R = R out - green
pin6 aud-ret-R = R ret - green
pin7 hp-on = empty
pin8 key
pin9 aud-fpout-L = L out - white
pin0 aud-ret-L = L ret - white
The above pin out gives nothing at all, but audio from rear ports on the computer motherboard is fine.
I also tried the following,
where the microphone wires were left disconnected, therefore just the speakers plugged into the front panel audio header
mobo = case wires/colour
pin1 aud-mic =
pin2 aug-gnd = gnd - black
pin3 aud-mc-bas =
pin4 aud-vcc = empty
pin5 aud-fpout-R = R out - green
pin6 aud-ret-R = R ret - green
pin7 hp-on = empty
pin8 key
pin9 aud-fpout-L = L out - white
pin0 aud-ret-L = L ret - white
The above still gave me no audio out from the front panel.
Intrestingly if I leave the front panel audio header blank, I still get rear audio fine, where I would have expected to have put jumpers across the L and R outputs as is the norm.
I have removed the front panel from the computer to ensure that the wires terminate OK, and have not been pulled out/off.
Have I plugged in the wires correctly?
Is there some hidden setting that I have missed, I admit that I do not like the Realtek audio software?
I cannot find any way to boost the microphone input since Realtek audio software has been installed.
One day case/mobo manufactures will use a standard for the front panel headers and front panel audio headers, and we will have a simple single plug to insert, rather than a group of single fiddly connectors that have to be attached to a header that was at the last minute attached to the motherboard as far away from the front of the case, and in the darkest most fiddle corner.
Oh well......
Cheers

AaronYuri - you're are so right there my friend. I just pity Joe User whom might attempt such a move themselves.
In the end my entire issue was software related, and that has to be blamed on Realteks software, far too many options approached from far too many different angles. Audio is really simple, plug your cables in, and it should just work, certainly in the simple case of 2-1 speakers and a microphone. Why exactly it took a couple of hours to figure out how to get the front panel microphone to be seen in the first place, let alone any signal, is beyond me.
So my cables were all connected correctly as per the MSI manual, confirmed by my Abit manual and other post here and on other forums.
In the Realtek MSI audio software, on the I/O Audio tab, connector settings, I had to select 'disable front panel jack detection' and 'mute rear panel output when front headphones plugged in'. The other option here 'enable auto pop up...' is unchecked.
After this the Realtek software mentioned something about a new profile had been set up?
I then went to Windows Control Panel, Sounds and Audio devices, and selected the voice tab, on this page I selected 'mic IN at front panel [pink]' from the drop down list for Voice Recording'. Proceeded to 'test hardware' and the microphone is now working. This option to select the input in the drop down list was not available before.
All a bit of POKE and HOPE.
But we seem to be there.

Connecting the chassis-mounted front panel audio I/O module to the X-Fi Extreme Mu

Hello to everybody.
Many pc chassis provide two audio connectors on the front side, usually for the headphones with microphone.
I need to know if I can connect the chassis-mounted front panel audio I/O module to the Sound Blaster X-Fi Extreme Music.
I saw that the X-Fi Extreme Music has the internal connector (named AD_EXT) to connect . Is there a pin mapping of the AD_EXT connector? Is it possible to connect the chassis-mounted front panel I/O module cable to the proper pin of the AD_EXT connector?
Thank you.

Hi and thank you for your response.
Unfortunatelly I actually haven't got a X-Fi card, because I need to know if I can connect the chassis-mounted front panel audio I/O module to the card before buying it.
For this reason I don't know what is the J you're talking about. Is it an internal connector avaiable in the X-Fi Extreme Music card? Can I use this J to connect the chassis-mounted front panel audio I/O module to the card?
Thank you.

MSI K9A2-CF front panel audio problem

Just rebuilt a computer using the board. Please note, I have not updated the BIOS at all and I am using XP Pro. Anywho, I've tried everything under the sun, so far, aside from previously stated, to get this sucker to work. I have it connected properly, I've installed every audio driver on the motherboard CD. I can't find a setting in the BIOS to turn on front panel audio either. Everything else works fine though. USB's, HD audio connections in the back, etc. The program in windows will detect all inputs except for the front audio in and out.
I'm a bit stumped. Any suggestions?

Quote from: Bas on 17-August-09, 22:22:14
You have to check the wires on the plug, looks like they are wrong or the case-module is broken somewhere.
You have to start checking and measuring with an Ohm-meter.
Remember, neither case front worked. I'm not saying it couldn't be the case, but I'll try to get my hands on an Ohm-meter. Where can I find out what values I'm looking for? I know next to nothing about testing to that extent.
Also, what if it's the motherboard itself? Isn't there somewhere in the bios and/or windows device manager that I can confirm whether or not the device itself is working, or not working, properly?
Thanks for your replies so far.
Mike,
I honestly don't know, but the case only has one audio cable, and the MB only has one audio plug-in for the front panel. I have both drivers installed. The on-board audio plug-in on the rear of the computer works fine. I can get sound, etc, no problem from the rear. Front panel only is not working.

Front panel audio wont mute rear audio when headphones are in.

Hello,
As the title says my sound isn't muted on the rear speakers when I plug in my headphones. The front panel audio didn't work at first, it said in the manual to disable front panel jack detection. Once I did this the audio came through the front panel, but is not muted at the rear, so I have sound from both the headphones that are plugged into the front and the speakers that are in the rear. The option to mute the rear output when headphones are plugged in is enabled, the speakers are plugged into the green jack, the rear speakers are set to stereo line out and the front is set to headphones.
Can anyone help, at the moment I have to keep unplugging the speakers to listen through the headphones without disturbing anyone else, which with the placement of my computer is not convenient.

Hello,
I have used the link, but the drivers just install the same one I already had (both the rar and the exe do this), even if I remove the previous drivers via programs and features. Unfortunately the problem still persists, I am really stumped as to what is causing it. I am not sure if I have AC'97 or HD Audio connectors on the front of the case, as the case came with absolutely no documentation. I have provided a link to the manufacturers website if that could help in anyway.
http://www.xionusa.com/Product-case-Xion2.asp

Front Panel audio headers

Hey all... I bought a case recently that has spaces for front panel audio + usb. Problem is, the case only came with the headers for the USB side of it.. I'm wondering if anyone knows where i can get the little device that i screw onto the inside of the front of the case so i can use the case to it's potential.. it's just 2 usb plugs (on top of each other) and to the right of it, the microphone and headphone plugs. I've seen it in other cases.. why they molded the case with it, but didn't put it on there... i don't know..
this is a Fudin case from Fry's Electronics ATX-208USB.
Any help would be MUUCH appreciated..
Thanks!!
CZ

I'm using nForce4 (with Realtek AL850) - thus audio chip a bit newer or the same as yours, yet I have to use dmix (although dmix is said not to be needed to be configured in newer alsa, I had less problems playing more sounds at once with my previous VIA 82xx, probably due to its DXS).

Front Panel Audio - P7N Sli Platinum Question

I am having trouble getting the front panel audio working - I want it set up so that when I plug my headphones in the speakers mute and the headphones take over.
I have the following:
Case - ThermalTake Armor VA8003BWS - http://www.thermaltake.com/product/Chassis/fulltower/armor/va8003bws.asp
MB - P7N SLi Platinum
Sound Card - Create Labs Xfi Gamer
I have done the following:
1. Disabled onboard audio in Bios (should I turn this back on?)
2. Went into Creative Console Launcher and checked the 2 options that I want it to automatically enable headphone settings and mute speakers when headphone jack is connected.
3. Connected 10 pin wire in case labeled (Azalia) to the motherboards Jaud1 (my MB manual says it is Azalia 1.0 compliant). The case also has an AC'97 connection (on the same wire as Azalia but I didn't use this because of what I read in MB manual about Azalia 1.0 compliant).
4. The case also came with this 10 pin black block that has all the Azalia descriptions on the side (Port 1 L, Port1 R, Port2 R, Sense_Send, etc. - I tried plugging the Azalia connector into this and then this into the Jaud1 but still nothing).
Not sure if it matters but my headphones are Plantronics Gaming Audio 770 (not USB).
Any suggestions?

Quote from: [LT]Eternalbliss on 21-June-08, 03:43:49
I've just recently had this similar problem. I think the issue in your case is step 3. I believe you should connect the Azalia 10pin wire to your X-fi card, not the mobo.
My problem was that i had connected AC97 10pin wire to my X-fi, after which plugging in my headphones didn't mute my speakers.
That was the problem - works great now! Thanks

Front Panel Audio is

Hi!
You'll have to excuse my english but it's not my nati've language.
I'm trying to install a front panel audio, and I figured out that the cables must be conected to the soundcard (Audigy 2ZS). I have a Termaltake Xaser Tsunami.
Can you help me, please?

Quote
Thanks. Its ironic that disabling it actually enables it.
It has to day with the front panel audio wiring of your case. How many wires are there that can be connected to the board's pin header?
Quote
Sound quality isn't very good
Can you be more descriptive? Is the quality better if you plug the headphone into one of the jack at the back panel? (Also, make sure you tell the Realtek HD Audio Manager, that a headphone is connected (and not regular speakers).

No sound front panel audio with newest CMI 9880L driver

Similar Messages

Maybe you are looking for