No Sound Heard

I am hearing no sound from jingles or my podcast recordings in Garage Band, any suggestions?

No sound from the Jingles means you probably need to install them from one of the install DVDs that came with the computer, usually Disc 2.
Are you saying you've recorded a Podcast and now can't hear it?

Similar Messages

When using webcam for movie making no sound heard

i am trying to use the web cam to make a movie, but when i play back what i rerecorded no sound heard at all
i checked the mic settings and it seems working OK. if you have any ideas it would be greatly appreciated

Hi,
We do not know your machine and its OS therefore can't help.
Regards,
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Startup sound heard continuously

Hi All
I have a Macbook Pro A1226 .
When I push the power key , the Startup sound heard continuously , but ther is no picture on the screen . help me to solve this problem.

I am having the same issue.
When I try to start my Macbook Pro, I get an endless loop (well at least 5 minutes before I give up and power it down) of the start up chime. It just keeps repeating over and over. THe screen stays black and never lights up. THe chime varies a slight bit, occasionally sounding like it cuts out half way before it finishes, but then a full chime will happen again.
I have tried the PRAM zap, Systems Management Controller reset (disconnect power and battery, hold down power button for 5 sec, reconnect to power and try again, as well as the Cmd-Option-Power hold down that is recommended for the newer Macbook Pros), tried safe start up (holding shift) even tried to boot in Target disk mode just to see if I could get info from the hard drive.
I have tried reseating the ram.
I have tried it with only battery (which does seem to be charging fine), with only ac power, with both.
Not sure if it anything but When it is plugged in and the battery is fully charged, the green light goes out on the charger and no light comes on.
Any help is greatly appreciated.

No sound heard in Audio Preview

Hello when I speak on the mic, the green bar in audio preview goes up and down however no sound is heard. How do I hear the sound from the mic during preview? Thanks.

As far as I know you can't hear the sound, just see the bars move. As long as the preview bars are high but remain green you know that your sound is being captured an the appropriate level. If you are unsure that your sound is coming through you could "listen" to the stream by opening it from the server, just to confirm that it is being captured.

Sound heard through headphones, but not with internal speakers

Recently, my computer stopped producing sound from the speakers. However, I plug in headphones and everything can be heard. I've already checked Sound in System Preferences. Nothing is muted and all sliders are in the correct position. In the Output Pane, my only option for the output source is headphones, no internal speakers. What happened? What should I do?

I recently got the same problem. Its not that bad but confused me at first. If that is the worst problem you get with your computer consider yourself lucky. You could bring it by an apple store genius and see what they say but its most likely a switch problem like tteuer said. If my memory serves me right that switch is connected to the logic board, if you have it still under warranty, great, if not, you might as well get another laptop if it really bothers you.
Tip: I have made it work by either slowly removing the headphone from the jack or rotating it. If that did not work the first time I repeated it.

C1-02 Sound heard from Earpiece and Speaker both e...

I recently bought C1-02 with FW 3.40, later I updated to FW 5.40. The problem is that the sound from Earpiece is being heard from back speaker also, without turning the speaker ON.
If I turn ON the speaker, there is no difference. When I play music from Speaker, its even heard from the earpiece.
Is this a flaw in the c1-02 model or firmware or just my phone?
If the flaw is in the model, Will there be a firmware update to fix this issue or is this a hardware flaw?

Sounds like a problem in your phone, it's definitely not a model issue.
Have your phone checked in a Nokia Care Point.

Click sound heard when clip audio is at 0

I am using iMovie 9.0.4. I have several video clips in my movie, with audio from a .aiff file througout. The video clips I am using have audio, but I don't want to hear it, so it set it to zero for each one. But with video clips with especially loud audio, even when set to zero, I hear a click sound when they start, as it it is late by 5ms in attenutating the audio to zero.

I am using iMovie 9.0.4. I have several video clips in my movie, with audio from a .aiff file througout. The video clips I am using have audio, but I don't want to hear it, so it set it to zero for each one. But with video clips with especially loud audio, even when set to zero, I hear a click sound when they start, as it it is late by 5ms in attenutating the audio to zero.

'Whoosh' sound heard when sending an email, immediately...

When I send an email with a particulary large attachment (I have a slow internet connection) I often hear the 'whoosh' sound played immediately, even though it's quite clear the email coulnd't have possibly been sent so quickly.
I think this has led to me sending an email, hearing the 'whoosh' sound and immediatley shutting my Macbook lid, putting it to sleep. Subsequently, the email never gets sent until I open Mail on my Macbook again.
This is annoying because I've 'sent' an important email recently, and then found it never reached its recipient and was sitting in the Mail outbox when I used my Macbook a few hours later.
Any ideas?
Thanks, in advance
*This issue didn't seem to occur when my Macbook was running OS X Lion.

How is this iPhone related?

Beep sound heard during startup

Am hearing a beep tone every 5 seconds when I startup my iMac computer. It is on macosx.
The last time I used it was when I was playing starcraftII and I shut down without removing the CD like I usually do. But this time when I startup the iMac does not boot up. I have tried resetting the SMC and it didn't work. I pressed down the mouse while startup and the CD didn't come out but I started to hear these beep tones, when I startup now. Thought it might be the memory card so removed them and tried starting up without them and then tried one by one and I still getting the beep tones, will I lose my hardisk as well if I keep rebooting too many times like this? How to get the CD out and startup the iMac properly?

Check this out:
Power On Self-Test Beep Definition - Part 2
Is it one of those beep patterns?

Headphone noise (pop sound) heard when switching to audio.

Has anyone encountered a popping noise when the start listening to audio (MP3s, starting a call, etc.) through their headphones? I am wondering whether this may be a design flaw, a setup issue, a hardware problem with my BB Curve 8830 or with the headphones themselves. I am using the headphones that came with the unit. I have had this problem from day one and it's really irritating. Thanks, Dan.

I have the same problem, actually two different pops. The first is a loud pop when using any kind of headphone or speaker, right when the music is about to start, almost identical to the old pop when one placed a needle down on a vinyl LP. (Anyone here young enough to remember those?)
The second is a softer but clearly audible pop between songs - however - this one is only audible using certain headphones and particularly speakers (like PC speakers). What is with this? Surely this is fixable - hello RIM ??
Any hints appreciated. My Curve is new, from Verizon, and appears to be using system 4.3. Will look into updates on that.
Not to hijack the thread, but perhaps I can toss out my other Media Player problem. I had trouble downloading with WMP and Roxio so I am using MediaMonkey - I can get songs, album art, and even playlist names but when I check the playlists on the Curve, they are empty. Anyone run into this? I have MMS enabled, USB support, etc. Thanks !

5g ipod nano earphone jack doesn't work, but earphones are OK. Sound of music comes from ipod heard w/o earphone jack plugged in . How, where to fix jack?

6th g ipod nano earphone jack doesn't produce sound with earphones that work on another 6th ipod. fairly loud music sound heard from ipod w/ no earphone plugged in. Hoe and where to get it fixed?

I fixed my nano sound problem. Went to settings, hit center button, scrolled down to reset settings, hit center button, scrolled up to reset and hit center button. Walah, Now earphone jack delivers sound to ear buds like before. AND yes the jack was always plugged in all the way. Simple problem, simple solution.

No sound when pressing numbers when dialing on keypad

When pressing the numbers to make a clall, there is no sound heard when typing each number. The sound works for everything else but this.

I am having the same problem: any luck finding a solution?

No Sound at

MY Sound card is Sound Blaster Li've! 24bit...
I have Windows XP
What I Tried:
Channeling each jack.....No Sound Heard
Clean booting.....No Sound Still
Check the Digitial Output Only.....Checked (No Sound Still), Unchecked (No Sound Still)
Check if my plug is plugged in the right jack.....Plugged in right jack
Restart my computer (normally).....No Sound Still
Replugging my whole speakers.....No Sound Still
Reading The "Sound Blaster FAQ" Sticky.....Didnt Help At All
Reading The "KnowledgeBase".....Didnt Help At All
Reading The "Windows Troubleshooter".....Didnt Help At All
What I Dont Want to Try:
Reinstalling The Dri've..... I dont know how to install it when i uninstall it
Call the Tech Support..... Im only 5
Opening my Computer..... I have no idea what to do once i open it
Anything that risks breaking my computer
Plz help me some, dont post any suggestions that could risk damaging or slowing down my computer.... Thank YouMessage Edited by jdm-ae86 on -04-2006:25 PM
Message Edited by jdm-ae86 on -04-2006:26 PM
Message Edited by jdm-ae86 on -04-2006:26 PM

bump

Thinkpad X201i wierd sound

I have test the system health check but no hardware error found. I had a problem with one weird 'tak' sound. System running Windows 7 is running as usual but I left it for about an hour and I touch it by lift it up or move it then I heard 'tak' sound. It appear only once. Later I move it again there is no 'tak' sound appear unless I keep it idle for about hour or half. Anyone experience the same behavior with me? if yes then I consider this is normal. Thank for any reply and helps

I did some test just now. I try to disable the Active Protection and leave the laptop on for half hour...after that I lift up the laptop and there is no tak or click sound heard....
then i enable back the active protection and straight away lift up the laptop and I heard the tak or click sound once, then i lift up again and again no more tak or click sound...but i will hear it again when it kept for half hour of idle...
any opinion?

Looping a single track of sleep sounds

I have made a recording of nighttime sounds heard during a recent visit to the Puerto Rican rain forest.    The recording is about 8 minutes long.   I wish to somehow "loop" it, so that I have a seamless recording that is an hour or so long, so that I can burn it to a CD and play it in my alarm radio (which can play a CD, but has no capability to handle an iOS or USB device), for "falling asleep" use.
The radio can be set to "repeat play" the one 8 minute track, but there is a distracting break in the sound when that happens.   I tried creating an iTunes playlist consisting of seven instances of the one track, and burning a CD while specifying "0 sec" break between tracks.   But even that created a distinct glitch (not due to the recorded sounds themselves not transitioning gracefully from the end of one instance of the track to the beginning of the next).
I seek advice on how to accomplish this.   I fear it is not doable in iTunes.   Perhaps there is some freeware that can accomplish the task relatively painlessly ?

I don't know if this is the best solution but if I were doing this I would take the sound file and paste it together in AIFF format using Garageband or a free editor such as Audacity and burn that to CD. You might even get some sort of crossfade to work to make it completely seamless.

No Sound Heard

Similar Messages

Maybe you are looking for