No sound out of Logic but audio is recognized
I bought an Oxygen 8 and I'm trying to use it with logic. I can see an imput signal when I hit a key but no sound comes out of logic at all.
The Oxygen 8 is running into an audio interface and then into my macbook via usb.
This set-up works fine in Ableton but not in logic.
Make sure you have a software instrument instanced in your track and make sure that track is being routed to the output. Then, check your levels, etc.
Similar Messages
-
I have just purchased a Korg Monotron and am very pleased with it!
I am trying to send sound out from Logic into the Monotron, and then filter the audio in the Monotron and record this back into Logic, however I have a problem.
The audio I want to send out of Logic is routed to outputs '1 & 2' on my Edirol UA-25 interface.
I take a mono output from one of these outputs on the rear of the interface, and feed this into the Monotron headphone socket.
The issue is that when the sound is fed back into Logic, I can't hear the filtering effects because it is drowned out by the audio track I am sending out.
How can I mute the sound of the outputted audio so that I can only hear the subtleties of the filtering effect in Logic.
Can anyone explain a workaround for this, or is there no solution as the audio always need to be audible to in order leave Logic, or else no sound would be sent.
Any advice welcome!
Cheers,
Mr RockHi Dat Stream Studio,
This sounds very promising!
Can you please confirm when in 'Audio Midi Setup', do I go to 'Audio Devices'.
If I select 'Audio Devices' then I have two setting- 'Default Output' and 'System Outputs'.
At present both are set to 'Edirol'.
Can you please suggest which ones I need to configure as 'Mac Internal'.
When this has been set up is all sound outputted through 'Mac internal' audio, and do I connect a lead from the iMac headphone socket into the Monotron?
To get sound back into Logic, should I connect the Monotron into say Input 1 on the Edirol, and then set up an audio track with the 'I/O' plug in set to audio 'Input 1 (and leave the 'output' blank)?
I look forward to your response.
Cheers,
Mr Rock -
Have had Logic Pro 8 for about five years. Suddenly could get no sound out of it. VU meters show there is signal on tracks, and I can record audio, but can't hear anything. Ran extensive diagnostics - all point to the problem being in Logic itself. Downloading the latest Logic 8 update made no difference. Help!
What result do you get when you bounce the project to- and start playback from- the Finder?
Have a nice day! -
NO SOUND! I can't get any sound out of logic express....
Very recently, sound stopped coming out of my Logic Express.
There is a level (on the master) going out, and the master volume of the program is up, but nothing is coming through the speakers!
All other sounds are coming out (itunes etc), just not logic. Has previously been working fine!
I must have clicked something by accident, any suggestions please?!?
AlexThe first time I synced with the ipad I did go through "restore" from iTunes. The other options on the screen were "restore from iCloud" and "new ipad".
How do I do a restore now? With the ipad attached? Everytime I connect and disconnect the ipad to the cable, even with reboot, it takes me back to the same grey iPad configuration screen. Do I need to do a hard reset? -
I want to plg my apple tv in to a projector but i want to break the sound out to a seperate audio solution. Is there a lead that I can use? The sound system has 2 x phono connections?
The sound can already be "broken out" by using the optiocal cable jack. That, of course, assumes your audio input is capable of optical inputs. If not, you might have alook into something like this: https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=opt ical+to+rca+converter&tbm=shop
-
I have just purchased a Korg Monotron and am trying to send sound out from Logic into the Monotron, and then filter the audio in the Monotron and record this back into Logic, however I have a problem.
The audio I want to send out of Logic is routed to the only 2 outputs '1 & 2' on my Edirol UA-25 interface.
I take a mono output from one of these outputs on the rear of the interface, and feed this into the Monotron headphone socket.
The issue is that when the sound is fed back into Logic, I can't hear the filtering effects because it is drowned out by the audio track I am sending out.
How can I mute the sound of the outputted audio so that I can only hear the subtleties of the filtering effect in Logic.
Can anyone explain a workaround for this.
I have tried to set up an aggregate device (can I record audio from my iMac instead?) and use the I/O plug in but with no success- any suggestions welcome!
Cheers,
Mr RockSorry- that was a typo- I take the output from Logic into the aux-in of the Monotron and then feed the output from the headhone out of the Monotron.
The issue is I cannot just hear the subtlety of the filtered Monotron signal back in Logic as the Logic output is playing at the same time.
Any solutions appreciated!
Mr Rock -
HELP!! No sound while recording thrugh M-Audio firewire 410
I am using Logic express 7 with an M-Audio firewire 410. I have my guitar plugged into the mbox and Logic is picking up the signal from my guitar, but I cannot monitor the sound while recording OR hear anything else at all. When I unplug the mbox, however, I can hear everything that i just recorded along with everything else in the song fine. I just need some help figuring out how to monitor the sound, PLEASE!!!!
Logic always uses the same audio interface for input AND output, so I suppose your problem is that you do not have any speakers connected to you M-Audio interface. Try adding a pair of speakers to it. If there's still no sound, go to Logic's audio settings and see if "software monitoring" is active or not.
Björn -
How do I use my M Audio M track Plus with the logic pro 9 software? It works with garageband, but I am not getting anything out of Logic. It does show up on list as option and I have done all of the sound preferences to M audio, etc. etc. Please help
I got to that page but clicking on the Subscribe Free had no effect.
Nothing showed in the Podcasts nor the iTunes U.
In fact I also subscribed to Stanford's lectures and despite actually managing to DL them there is still no subscription in iTunes U, just the Intro to Computer Science belatedly.
Peter
I'd like to attach the screen grab of the out of order and randomly DLed selection of Harvard's course, but the forum won't let me attach it even though it is only 456k. Correction, close post and retry and now it lets me. NB how intermittent the DLs are and in no particular order. -
In logic Pro, when I open up an audio track or software track and load an audio file/loop or software file loop, there is no sound. I will finally get a sound out of one of the audio or software tracks after opening at least 5 of them alternately. Is anyone familiar with this kind of bug? It's really frustrating as this takes much time to complete work.
os x, Mac OS X (10.6)I'm not sure I follow your words Fuzzynormal. You've helped by offering the insight that my issue in Logic Pro 9 is not a bug but a feature. But fell short of enlightenment by being a judge of character and of how one should interact in this forum. You insinuate that I haven't tried to solve the issue on my own when in fact I have. These forums are always my last resort. You further suggest that I am complaining. This is not a complaint. It is a genuine issue that I cannot figure out. Then you think that Brazeca is holding my hand and being a nice guy. Brazeca is helping people like me who might not be as adept at using Logic Pro as probably you are.This community forum was established to raise questions, answers and dicussion to help Apple's customers better undertand their operating systems and related issues. You are doing a disservice by not contributing positively and by trying to make this forum what you want it to be. You may have all the time in the world to try figuring out stuff but we are not all like you. We all have different schedules and different levels of understanding. And that is what this forum is for - to help people move forward. If you can't contribute positively then keep silent. And by the way, you say to "read the words that are printed down to explain to you how that works" what words are you talking about? Why don't you be of some help instead of trying to own this forum.
-
Sound is out of sync in iMovie and video freezes at a part but audio continues. How do i fix this???
Can someone please help me. I have even tried the youtube videos and can't seem to get the sound to sync up on my videos in Imovie. Also, one part just stalls and stays on the same frame but the audio continues on fine.
I NEED HELP!!! This is for school and I can't hand this in all wacked out44100 Hz is fine and the audio codec is fine. Most camcorders record at 48000 Hz, but audio CDs are recorded are 44100 Hz, and iMovie handles them well.
However, your video frame rate is an odd number. A camcorder in the US will usually record at 29.97 frames per second. In Europe, the standard is 25 fps. On some cameras, you also have the option of 24 fps (same as a Hollywood movie).
Your camera is recording at 14.89, which is about half of the 29.97 standard. I am guessing that the video is from a webcam or maybe a cell phone or still camera. It is difficult to sync audio over long periods of time if your video is not conforming to the standards. Cameras like this may record at varioable rates, so sometimes you get more than 14.89 and sometimes less. Your best bet would be to make an iMovie project at 29.97 fps, so that it will basically repeat each frame of your video twice to get up to 29.78 fps. Even so, it will drift out of sync over time.
If you had Final Cut Pro X, you could use the tools in FCP to conform your video and audio to a 29.97 timeline and probably keep it synced better. Long term, your best bet is to use a camcorder that can shoot 29.97 (or 30) fps.
Short term, I would suggest keeping your clips in your project short. For your 15 minute clip, drag in the first minute, then the 2nd minute, etc. untill you have it all. Even so, it may drift. Detaching audio is probably not necessary. -
No Sound out- test one, two- Sound bars are lighting up but nothing coming out built in audio
For some reason I can't get any sound out of premier pro. I haven't used it many times before but I'm sure I ahd audio when I did.
I switched from doing compositing in After Effects to PPro because AE was chooking on a simple luma track matte using one video to matte/key another... so I find myself in PPro.
Is there anything simple I could be missing which would explain why I'm not getting audio out of my Built-in speakers from Premier? iTunes kicking out the jams no probs.\ as was AE
Strangly every time I start SoundFlowerBed it quits as soon as I leave it. Normally keeps a little flower icon in the menu bar (OS X) to access it and route it's audio bus (SoundFlower itself is a low-letency audio routing system extension) to various outputs.
With SoundFlowerBed I can access OS X Audio Setup (as opposed to Sound Control panel)I found an uninstaller in Utilities and it has a cross thru it indicating not OS compatible. I dounble clicked and tells me it's a PPC app that can't be run (since I'm on 10.7.5 no rosetta for PPC). I'm not certain that relates to the actual SoundFlower that is running, it may just be a relic of auto-migration from a PPC MacPro.
Are you taking guess Jim or do you know there are issues b/w the two softwares?
I'm going to the Cycling74.com | Soundflower website now to investigate further. -
i recently got new mac air and transferred my old version garageband projects now when I open them in 10.0.2 I can add new tracks but then nothing can record, shows its receiving sound from software inst. but no sound. I checked audio preferences and they are set as they should be. I tried it in all the other older projects and same issue anyone have any experience like this very frustrating. Can one download old version still ? or can you run both versions on OS10.9.5 ?
Ok, either my question was too long or nobody seems to have an answer. Sad, either way
Here's something I found out in the meantime, maybe this is interesting for somebody or maybe - problem's not totally solved - enough info for any of you to give me further advice.
When I start Logic Core Audio driver de-activated, I can open old songs. Then I save them in a new folder with all audio files and a new name. And I remove all EXS24 instruments as well as the Space Designer. I quit Logic, re-open with Core Audio activated and I can open the song.
Problem no.1: EXS24 instruments don't find the appropriate samples, but EXSMananger Pro did help me with this. Same problem with Space Designer, which doesn't find the impulse responses, connected to a certain preset.
Two questions, every idea would be great!
- Is there any way to teach Space Designer Presets where to look for impulse respones. I can load IR samples directly and create a new preset, but I can't use my old ones.
- Is it possible to install Logic from scratch over an existing version? Or how should I de-install everything connected with Logic and then install a fresh version from CD?
Thank you again,
Joern -
i recently got new mac air and transferred my old version garageband projects now when I open them in 10.0.2 I can add new tracks but then nothing can record, shows its receiving sound from software inst. but no sound. I checked audio preferences and they are set as they should be. I tried it in all the other older projects and same issue anyone have any experience like this very frustrating. Can one download old version still ?
thanks,Ok, either my question was too long or nobody seems to have an answer. Sad, either way
Here's something I found out in the meantime, maybe this is interesting for somebody or maybe - problem's not totally solved - enough info for any of you to give me further advice.
When I start Logic Core Audio driver de-activated, I can open old songs. Then I save them in a new folder with all audio files and a new name. And I remove all EXS24 instruments as well as the Space Designer. I quit Logic, re-open with Core Audio activated and I can open the song.
Problem no.1: EXS24 instruments don't find the appropriate samples, but EXSMananger Pro did help me with this. Same problem with Space Designer, which doesn't find the impulse responses, connected to a certain preset.
Two questions, every idea would be great!
- Is there any way to teach Space Designer Presets where to look for impulse respones. I can load IR samples directly and create a new preset, but I can't use my old ones.
- Is it possible to install Logic from scratch over an existing version? Or how should I de-install everything connected with Logic and then install a fresh version from CD?
Thank you again,
Joern -
Trouble Sending Audio Out of Logic
Hello,
I'm having trouble sending audio out of Logic through outputs other than to my monitors. I am trying to reamp a guitar sound and send vocals to a reel to reel using a MOTU ultralite. Also, even though the audio tracks are mono, it only allows the output to be through stereo pairs. Thanks!Ok I figure out how to set my outputs to mono but I tried using one of the monitor outs to send audio out and it won't work, I can't even listen on headphones. When I plug my monitor back in, however, it works fine. What isn't working?
-
No sound out of my Tascam 1884 with Logic 8
Hi there,
I recently picked up a Tascam 1884 to use with Logic 8. I have my 1/4" jacks hooked up to my monitors and the 1/L and 2/R outputs on my 1884. I have the "MON MIX" button pushed and "Both" on as well. I've got nothing. I've read other forum posts stating that the MON MIX button is the fix, but it didn't work for me. Is there something in Logic 8 I am missing? Nothing is coming out of the headphones output either. Of course I get sound out of the computer, just nada from my Tascam / monitors. POO!!! Any ideas?
Thanks,
SethageYes. I turned on the "Direct TDM" under the audio preferences, it all worked after that. Thanks.
-Seth
Maybe you are looking for
-
Print a report to a printer (server-side printing) Error
<p>Hi ran into some hiccups following a sample from crxi_r2_jrc_desktop_samples</p><p>JRCPrintReport</p><p>I am attempting to send a report for printing on a Thick Client Application.</p><p>This is the error.</p><p align="left">- All configurations c
-
How to start managed server from admin server both running on separate machines
I have an admin server on one machine and created a managed server on different machine, I am not able to start managed server from either machine. When I used the admin server machine to start the managed server remotel
-
Function not executing in oracle 10g
Hi ALL, I have a problem executing below Function in oracle 10g. Pls do help me solve the prblm it wud be a great help. Thanks in advance. Here is a below function and the error i am getting: create or replace FUNCTION UnpackArray Source IN VARCHAR2
-
Problem accessing Document object UDF
Hey All, I am trying to build a custom application for a company that us using SBO patch level 21. Unfortunately they cannot upgrade to a newer patch level at this time. I use the following code to check the existence of a UDF field: if(myDocument.L
-
I am more than a little bit angry when I plug a Lightning cable or wall charger into my new iPhone 6 and it tells me that either or both are 'unsupported devices.' I'm not talking about those cheap, Chinese knockoffs. I expect Apple to 'protect and s