No sound with Audigy 2 ZS and WinFast PVR softwa

Hi! I run Windows Vista build 5744 and WinFast PVR software with WinFast PVR 2000 tv tuner, the problem is, when I run li've tv I can`t get li've sound just when I record, it`s recording with sound. In Vista Media Center it`s all ok.
Help please!

Still no reply? I d like to make it straight. My SB Audigy 2 ZS is connected through analog to creative 5. speaker system. The speakers are calibrated so I can hear surround music in media players or in All games which supports EAX. (e.g. Doom3, Half-Life 2). The only problem I have with good-old Diablo 2. The game supports Dolby Surround ( Pro-logic?) and EAX2. I enabled 3D sound and environmental Effects but I hear sound only from front speakers (L+F, center, subw). The rear speakers are quiet. Do you have any expirience with this issue? Do I need an external decoder through SPDIF for DD surround? The cinematics are encoded in dolby surround so Audigy might not to recognize it's Too many questions...
The Blizzard support is not replying..

Similar Messages

No rear speaker sound with Audigy 4 and Vista x64

I recently upgraded to Vista x64. I downloaded the 6.0..24 driver for x64. I also loaded MediaSource for x64. I am using analog 5. surround speakers from Dell. This setup works fine when I boot into XP pro (with the XP drivers), but I only get front, center and Sub in Vista x64. Does anyone have any ideas for this?

Not sure what to tell you, hopefully someone will be able to help. One curious thing though is that according to my Sound properties in Control Panel SPDIF is working on my Audigy 4,
<center>
http://i0.photobucket.com/albums/a7/stormy352/th_spdif.jpg">
</center>
unfortunately I don't have anything that uses SPDIF to be able to test it.
Also have you tried installing the X-Fi drivers yet? Download, extract with Winrar (or whatever you use) and navigate to the Drivers sub-folder and run the Setup.exe there.

No sound with Audigy 1 and Vista Ultim

Ok.. so I know you cannot use the SPDIF output on the x64 version... so I installed the reg x86 version and I still cannot get the sound to work on my Audigy with my old DTT2500 5. creative speakers..... Is there some setting that I am missing?... While playing an MP3 I am able to see the green bar move up and down on both the Speaker output and SPDIF output but neither of them produce and sound... speaker test works perfect as does my normal XP boot.. please help.. thanks in advance.

Not sure what to tell you, hopefully someone will be able to help. One curious thing though is that according to my Sound properties in Control Panel SPDIF is working on my Audigy 4,
<center>
http://i0.photobucket.com/albums/a7/stormy352/th_spdif.jpg">
</center>
unfortunately I don't have anything that uses SPDIF to be able to test it.
Also have you tried installing the X-Fi drivers yet? Download, extract with Winrar (or whatever you use) and navigate to the Drivers sub-folder and run the Setup.exe there.

Help! Sound Blaster Audigy - bass and tre

Hello! I had a Sound Blaster Audigy. There are any problems in the control with the Creative Surround Mixer. It cannot to set the bass and treble. Why and what is problem with it's Thank you!?Problem with the Sound Blaster Audigy - bass and treblehttp://icq299885550.mysinamail.com/Photo/Creative.jpghttp://icq299885550.mysinamail.com/Photo/Creative2.jpg?Message Edited by mrchan2002 on -7-20062:27 AM

What's the model number of your soundcard? Certain series of Sound Blaster doesn't support adjusting bass and treble so you have to use the Graphic Equalizer software instead to adjust it.
Jason

Sound Blaster Audigy Drivers and Applications CD-Rom

Does anyone know where I can get or download?the "Sound Blaster Audigy" "Drivers and applications" CD-rom?
I have included a pic below:
<img alt="cd-rom" src="http://www.geocities.com/pershingbpa/soundblastercd.jpg" align="left[/img] width="70" height="705">

jay23,
First extract the RAR file you downloaded using WinRar. During the extraction, WinRar will create an ISO file which is an image of the installation CD. If you don't want to burn that ISO file to a CD, then download and install MagicDisc from the link I gave above. MagicDisc lets you mount an ISO file as a virtual hard dri've. You should be able to install from that virtual CD just as if it were a real hard copy CD, but I've never tried that so can't say for certain.

No sound with Flash 15 and Windows 8

No sound with Flashplayer 15 and Windows 8. I have followed the steps to enable the program and to disable Active X filtering and still no sound. Sound works on all other applications.
The Adobe website instructions refer to a way to troubleshoot sound that cannot be followed -- see the inserted text below -- it refers to an application below and there is no application shown on the page.
Can someone please help?
How do I test my speakers?
Click Test Speaker in the application shown below to hear a sample sound. Adjust your speakers or headset so the sound is at a comfortable level.
How can I display this panel again?
You may want to display this panel again if, for example, you want Flash Player to use a different microphone. To display the Microphone panel:
Right-click (Windows) or Control-click (Macintosh) the application image while it is playing.
From the context menu, select Settings, and then click the Microphone tab.
I don't see the Microphone tab, so I can't display this panel.
If your computer or device doesn't support audio recording using Flash Player, you cannot select a microphone to use, and this panel doesn't appear.

Hi
Is the sound card recognized properly in device manager or can you see yellow exclamation marks there?
I have founded an interesting article on the Toshiba website regarding no sound:
http://aps2.toshiba-tro.de/kb0/TSB7C021B0001R01.htm
By the way: You can also mute/unmute the sound if you press FN+Esc. Check this!!!

SOUND BLASTER AUDIGY SE AND VISTA DRIVERS WITH FULL FUNCTIONALITY- WOOOOO

(ONLY DRAWBACK IS THAT YOULL HAVE TO FIND ANOTHER MEDIA PLAYER BESIDES WINDOWS MEDIA PLAYER FOR YOUR SAVED AUDIO FILES: I WENT WITH WINAMP)
CONTINUE ON-
Download RAR file with ISO inside and install if you don't have the installation CD
installation cd with EQ download: http://files.filefront.com//;689430;;/
If you do or after you finish downloading goto step A.
A) Take your Creative Driver/Install CD, copy it to your hard dri've.
B) Goto Setup.exe right click, goto properties, goto the Compatibility tab.
C) Set it for Windows XP SP2.
D) Run install the Creative Audigy and if you need MediaSource *WMP Will pop and hiss while multitasking I reccomend MediaSource as it does not although the "Sources" is glitchy.
E) Restart when told to
F) Part ) Right click on the speaker icon by the clock, click Audio Devices... Right Click on Playback Control, goto properties click Configuration Set it to Stereo hit apply.
F) Part 2) Goto Speaker Settings, Set the configuration to 5./7. depending on what you need, then make sure Sync with Control Panel is UNCHECKED I found that is the critical element! Enjoy your multichannel!
G) Part ) Right click on the speaker icon by the clock, click Audio Devices... Right Click on Playback Control, goto properties click Configuration Set it to Stereo hit apply.
G) Part 2) Goto Speaker Settings, Set the configuration to 5./7. depending on what you need, then make sure Sync with Control Panel is UNCHECKED I found that is the critical element! Enjoy your multichannel!Message Edited by jeepbme on 03-08-200708:49 PM
Message Edited by jeepbme on 03-08-200708:50 PM

estebandit wrote:
Is there a known issue for this
Yes it is called trying to install the wrong driver for your card. Will work much better if you try installing the correct one,
SBAX_PCDRV_LB_2_8_000.exe
Also helps if you click on the "Show Details" link on the download page, then you would see that the one you tried to install doesn't support your card,
Requirements:
Microsoft Windows Vista 64-bit, Windows Vista 32-bit, Windows XP Professional x64 Edition, Windows XP Service Pack 2, Windows XP Media Center Edition 2005 or Windows XP Media Center Edition 2004
Sound Blaster Audigy Value/SE/LS, or Sound Blaster Li've! 24-bit audio devices
whereas the correct driver shows the following,
This download supports the following audio devices only:
Creative Sound Blaster Audigy including Platinum and Platinum eX series
Creative Sound Blaster Audigy 2 including Platinum, Platinum eX, and Value series
Creative Sound Blaster Audigy 2 ZS including Platinum and Platinum Pro series
Creative Sound Blaster Audigy 4 Pro and Sound Blaster Audigy 4
Creative Sound Blaster Audigy 2 ZS Notebook PCMCIA

Distorted / choppy recorded sound with Audigy 2 ZS and Vista 64-bit

Hi, I wonder if anybody has any idea of why this issue is happening. First let me give you my PC specs:
CPU: AMD Phenom II X4 940 @ 3.0 GHz
Mobo: Gigabyte GA-M57SLI-S4 rev. 2.0
Graphics: 2 x BFG GeForce 8800 GT 52MB
RAM: 4 x GB G.Skill PC6400 @ 800 MHz
Sound: Creative SB Audigy 2 ZS
TV Tuner:? Hauppauge WinTV PVC PCI II (26xxx)
OS: Windows Vista Ultimate 64-bit SP
?So here's the deal. I have no problems whatsoever with audio playback with this sound card. The issue I am having is while recording sound with it. When I record my voice via a Microphone with the Windows Sound Recorder and then play it back, my voice sounds very choppy. It sounds as if I was talking in front of a fan. The same happens with any program I try to use. If I use Audacity to record sound, the playback is also distorted / choppy. The main problem is with Skype, as I cannot use it to talk to people because they cannot understand what I'm saying because of the issue. Does anybody has any ideas why this happens? My PC is a dual boot PC with Vista 64-bit and XP 32-bit, and this issue only happens with Vista. Sound recorded plays back fine under Windows XP.
I am using the latest drivers available for this card from the Creative site.
I'd appreciate your help,
Daniel

StormPetrel wrote:
A little bit off topic here, but 64bit does not mean more performance at all lol.
Sure, but there are in some cases drastic performence diferences. Under a fresh installed Vista X64 i have less CPU usage, as under 32 bit. But of course X64 uses more RAM (some tasks are double 32 and 64 bit).But the main reason I have more performence is, that the games I often play, get almost a boost. Dont ask me why, but under 64 bit EAW and FOC have the same FPS as under 32 bit. But under X64 I use a bit more Details and a higher resolution. (both are 32 bit games, so its a bit funy )?______________________?Sure there are other ways to install the drivers. But if some Setup dosent work, the first thing I try is to get it via Divice Management. And as this worked for me, I dont waste time to try other methods (Had bad experience, you can break the driver faster than install it *G*)?______________________?Some Questions I have left (after a few hours undr X64 with Creative Drivers):?Could it be, that the driver causes sometimes havy CPU usage?Could it also be, that the driver causes some lags, after you copy a file (the end sound, copy is finihed, but takes more time for "final finish", than without the drivers) - I know that Vista has some problems, on some PCs with copy, and that MS has an inoficial Patch (but dosent help for my PC so far)

Creative Sound Blaster Audigy ZS And Vista Driver installation prob

HI!
I encounter Installation problems with that file:
Creative Sound Blaster Audigy Value/SE/LS and Sound Blaster Li've! 24-bit XP and Windows Vista Pack .04.0077
I Use Vista 64Bit Ultimate and when I try to install this package I have an error message after my language selection. Is there a known issue for this
Thanks!
Julien

estebandit wrote:
Is there a known issue for this
Yes it is called trying to install the wrong driver for your card. Will work much better if you try installing the correct one,
SBAX_PCDRV_LB_2_8_000.exe
Also helps if you click on the "Show Details" link on the download page, then you would see that the one you tried to install doesn't support your card,
Requirements:
Microsoft Windows Vista 64-bit, Windows Vista 32-bit, Windows XP Professional x64 Edition, Windows XP Service Pack 2, Windows XP Media Center Edition 2005 or Windows XP Media Center Edition 2004
Sound Blaster Audigy Value/SE/LS, or Sound Blaster Li've! 24-bit audio devices
whereas the correct driver shows the following,
This download supports the following audio devices only:
Creative Sound Blaster Audigy including Platinum and Platinum eX series
Creative Sound Blaster Audigy 2 including Platinum, Platinum eX, and Value series
Creative Sound Blaster Audigy 2 ZS including Platinum and Platinum Pro series
Creative Sound Blaster Audigy 4 Pro and Sound Blaster Audigy 4
Creative Sound Blaster Audigy 2 ZS Notebook PCMCIA

"Sound Blaster Audigy Fx" and stereo mix availability

If I buy/install the "Sound Blaster Audigy Fx" will it add the stereo mix option to my sound properties, also
does this card work on windows 8?
http://www.bestbuy.com/site/creative...&skuId=3287009

Re: Sound Blaster Xtreme Audio missing Stereo MixK I think I'm having a similar problem with my Windows 7 Professional system.
I'm am getting sound out of my card.
When I right click on the "speaker" icon in the task bar I see the following list of 5 options
Volume Mixer
Playback Devices
Recording Devices
Sounds
Volume Control Options
However when I click on "playback devices", "Recording Devices" and "sounds" nothing comes up.
What I did do is completely uninstall all traces of any installed Creative software and in the device manager did an uninstall for the SB Xtreme Audio Card.
My recording device is the integrated microphone in the Logitech Quickcam/IM that I have installed. If I go to accessories and click on "sound recorder" it doesn't start up either.
The other issue that I see is that when I go into Control Panel and click on Sounds, nothing happens.
Something is definitely going on but I can't seem to track down the cause.

I can't adjust the sound with the f11 and f12 key

Hey folks,
after the installation i can't adjust the sound of my macbook with the f11 and f12 keys.... first i think it doesn't work with the keys ONLY but then i check the sound settings .... diffrent way same problem ... so i'm looking for help

Resetting the PRAM worked for me.

Choppy sound with Leadtek DV2000 and Sound Blaster X-FI SB

hy, i have a Sound Blaster X-Fi SB460, and i have trobule with sound on my tv tuner.....with another sound card, the sound is OK, but with this card the sound is verry strange, and i more loud and choppy and distorsioned....please help me.....
sorry for my bad english.....

So with your 65 whopping posts, what exactly do you think you are contributing to this forum? The user has a Sound Blaster-branded sound card, so in my opinion, he is in the "correct" section.
Originally Posted by Octopuss
You win imbecile award of the month for ignoring forum sections.

"A How-To" on the steps to FIX the Problem of NO Sound Card DETECTION with AUDIGY 2 and Win XP

Note#: When restarting the PC each time, shut off the main power switch on the Power Supply then back on.
Note#2: You will need the Windows XP CD WITH the SP2 on it or have the download SP2 Install file from MS on your PC. I have it on CD.
. Remove the sound Card
2. Use the Removal/Un-installation Procedures for the drivers in Knowledge Base Under Windows XP Step by step. Restart to get all the files deleted in the Creative folder if necessary.
Here is the (Solution ID#) for the Uninstallaion found in the Creative.com Knowledge Base: SID72 "How to uninstall Sound Blaster drivers and applications?"
Alternati'vely, Click on the Sound Blaster Picture Box under the Knowledge Base Main Search Page and the article should be in the resulting list.
3. Use the DCProSetup_.exe from http://files.trunetworks.com/utilities/
Use it carefully Selecting [Creative] then Check the box for Muntiple Cleaning Filters, and remove the Creative Audio Drivers by Clicking on Start.
4. Go into the Registry by Typing Regedit in the Start>Run.. Menu
Navigate and remove the Entry for CTCMSGo.exe, it is running in the back ground otherwise and i believe it interrupts the re-installation of MediaSource Files.
HKEY_CURRENT USER\SOFTWARE\Microsoft\Windows\CurrentVersion\Run
The file link/tag, it will be on the right half of the screen, Delete it. CTCMSGo.exe=(Creative Technologies Media Source Go)
5. Restart the PC, dont forget to switch Power Supply to off while powered down and on before powering back up.
6.Go to the Win XP SP2 CD or the file downloaded, select re-install but choose UPDATE, not New Installation. Let the Install run and update your pc, this procedure has no data loss or settings changes in Windows.
7. Restart PC
8. Turn off PC and install the Audigy 2 Card. Then turn on the PC. At this point you might get a plxcore.plx Error of file missing. Not to worry.. copy the file from within the Creative Drivers CD and paste it into the Creative Folder In C:\Program Files\Creative
The Knowledge base Article on the steps is: SID287 "Error: Program could not load because Plxcore.plx cannot be found"
9. Power up and see if you get PCI Device, and Audio Controller Detetion. If you dont then do the following:
A) Remove the Sound Card and Re-install the Win XP SP2 Update a number of times ( I did this about 5 times until detection) Each time restart and install the Sound Card into any of the empty PCI Ports until detection.
If that does not work after a number of times try the following:
B)Power off and switch the PCI slot of the Sound Card (to all the PCI slots if necessary with complete power off each time) Without Re-installing XP SP2 Update.
0. After you get Detection, The Windows Auto Installer for Drivers will pop up..select Find Drivers Automatically, then Install then install the drivers it finds. It will put in some basic Audigy Drivers from the CD or online i'm not sure where it gets them from. Keep your Driver CD in the CD Dri've.
.Restart the PC, then install the Drivers and Media Source Files from the CD (it may not all get installed and may give an error and you have to shut down and re-install the drivers and Media Source over again and over again so it fills in the gap of missing files/drivers until it all works without deleting the previously installed parts).
2. Only install this update from the File/ Downloads Section on the Creative website: EAX4DRV_AUDIGY2__84_50.exe Dated 29 July 04. The new beta one that was released is what started all my troubles, so plz i urge you to wait for it to be official.. unless you really want to test it out at your risk.
And there you have it.. in 8 Hours and some ideas from friends and relati'ves concerning detection problems of other hard ware they have had i decided to play Roulette all night and this combo works. I had to play Roulette switching the PCI slots (5 of them), and then towards the end play Roulette with the Creative Driver CD install... until they all work perfectly. WHEW!!!
Notice: I hope if you are really ticked off at having no sounds and want to try this at your own risk and responsiblity go ahead, and I wish you luck. None of the proedures are too out of the ordinary. I dont know if it will work for you but it worked for me and maybe it will possibly for other similar Sound Cards as well.. like ZS or Li've! etc. with similar problems. Happy Sound Blasting!!!
My Specs: P4 3.2Ghz Prescott on Intel D875PBZ MB, pqi GB PC3200 Dual Channel RAM, Win XP SP2, Plextor CD-R and DVD Dri'ves, BFG 6600GT OC 28MB and the Audigy 2 Sound CardMessage Edited by Flying_Ghost on 05-04-2005 09:38 PM

Thanks for pointing that out, it was not apparent on the day i used them and wrote the How-To. The links have been replaced with the SID# (Solution ID #) and the title given for the Article.
Have fun

Problem with Audigy 4 and Asus m

I own an Asus A8V motherboard, and just purchased the audigy 4 non-pro. While playing the game F.E.A.R. (main reason I bought the soundcard) with acceleration to the max, I will receive a BSOD (blue screen of death) with the 0x0000007F error code. When I turn the acceleration down 2 notches ( above the lowest) I am able to play the game without getting a bluescreen, but I will hear sounds a second or 2 after an event so this is a big problem, and have screeching problems on some ma
ps.
I've heard that some Asus mobo's and the newer Creative cards have issues, any way to fix? I'm using the latest drivers for both my mobo and my sound card.

Please can someone help?

Digital Connection with Audigy 4 and DTS5

Hallo Everybody
I have the same Problem with the nice man in this post. (Felix2)
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=46632&vie w=by_date_ascending&page=
Exactly same problems! I emaild the Support and they replied me just trash.
So my base problem and thats in the linked thread above is to get a standard audigy 4 not a pro! optical connected to the dts 5500 er Station.
Please do not tell something of 5channel sound and ac3 and ac3 and ac3 its useless.
Please do not ask me about my system config, all works fine, the audigy4 works fine, my dts works fine and the speaker too. (Ive testet it with the 3 pole minijack connecters of my audigy 4).
So all works, but the opticalDigital connection not. (And i dont want to get 5. sound, i just want to get some sound, at the moment no sound comes out)
se give a statement why optical/digital connections not work on your products.
-Please give a statement why this is that difficult/confused to connect.
And a big bravo to Felix2. I wouldn't stay that cool like you if I get some horrible and wrong answers, especially of a "professional". Maybe you have a solution do get the DTS 5500 and audigy 4 get optical connected?
Greetings
Lex

Lex,
The information I gave Felix2 is not "horrible" or wrong, they are the truth. There is no need to start attacking again, if you are not clear on the information I gave in his thread, ask for more clarification, but do not attack.
If you are having problems getting it set up, it's best to provide some detail on what settings you have changed, how everything is configured, and someone will probably be able to help you.
The start of your post isn't very clear, do you have a standard Audigy 4 or an Audigy 4 Pro? The Audigy 4 Pro does have an optical output on the external dri'vebay, the standard Audigy 4 (just a card) does not have an optical output. You would need to connect through a coaxial input (minijack to RCA, then RCA-RCA).
Cat

No sound with Audigy 2 ZS and WinFast PVR softwa

Similar Messages

Maybe you are looking for