No Startup After System Software Update

I updated my software last night from the Software Update that the system automatically runs. When I shut down my computer, it gave me 2 choices: "Shut Down" and "update and Shut Down". I chose the latter. This seems to have been a big mistake.
This morning my computer won't boot up. It runs the gray apple screen with the spinning disc of lines for a few moments then shuts off. I've tried starting it up pressing the Shift, X, C and CMD-S keys (at different times of course). Same thing. I managed to get the Leopard Install CD into the CD drive. Same thing. It spins for a bit then stops. A couple minutes later the computer shuts off while still on the gray screen.
I've tried resetting the PMU reset button.
I've unplugged all peripherals. I even unplugged my second hard drive. No change. Gray screen for a few minutes then shut off. I even tried booting it with nothing but the CPU running. I unplugged the monitor and it still runs for the same amount of time then shuts off.
Can someone tell me what the heck the software update did to my computer?
More importantly, HOW CAN I GET IT TO WORK AGAIN?
Please help! I'm lost without the use of my computer!

Now, the fact that it shuts down after a few minutes indicates that there is something that the system does not like.
Have you tried "verbose mode"? This will replace the Apple screen (which is the pretty logo that hides what is actually going on under the bonnet) with rows and rows of writing (UNIX script). It will tell you things such as "invalid" "error" "fails" amongst the lines:
http://support.apple.com/kb/HT1492
You may have to try this a couple of times.
NB: You have reset the S MU, only ONCE have you? (opened up your machine):
http://support.apple.com/kb/HT1436 (do not press it twice)
NB 2: You could try an NVRAM reset:
To reset the NVRAM
Boot holding "option + apple + o + f" until you get a white screen with black text. Upon releasing the keys you are presented with a command prompt.
1. type "reset-nvram" at prompt and press return (will say OK if successful)
2. type "reset-all" at prompt and press return (you will see a quick flash of commands and screen will blank)

Similar Messages

IBook G4 will not restart after system software update

After updating the system software, via software update, the system will not get past the initial gray screen with the spinning dial.
This is my daugthers computer and she is out of town working and does not have any of the system disks with her.
Any suggestions are much appreciated.
Thank you!
iBook G4 Mac OS X (10.4.7)
Yikes! Mac OS X (10.4.3)

George
Boot your computer from the install DVD, insert the DVD and shutdown the computer. Boot up while holding down the C key. Just before the install sequence you will see options in the menubar, select utilites, go to disk utility, select your target disk, verify and repair disk. You might want to verify and repair disk permissions as well. To answer your question it's not a virus as there are no viruses for MacOSX. It could be the updates did not install properly. Try that and follow with a post to let us know if that worked for you. What software update were you running when this happened?
Joseph

Computer does not startup after canceled software update

I was installing the newest version of leopard. It seems as though leopard installs the update while the computer is starting up (?), as opposed to tiger, which downloaded the update while the computer was still on.
anyway, i was feeling impatient and decided that the update was taking to slowly and that i should just cancel it and update it later.
however i made the stupid decision of forcing my computer to turn off (by holding down the power button)
now whenever i try to turn on the computer, it will get to the screen with the apple and the rotating circle-thing below it
however, it won't get past that part, i left the computer for an hour and when i got back, it was on the same startup screen
i'd appreciate any help anyone can give me

You damaged your OS when you did a force-quit.
Restart your machine with your original Leopard disk in the drive while holding down the "C" key until you see the Apple.
Then you can re-install your OS. You should back up your data to an external hard drive by doing an "archive and install" which is one of the options you will have when you begin.
If you don't have a hard drive, you can just re-install the OS and then update again.
Installing with first backing up is not recommended since there is always the possibility of some problem installing new software that could result in data loss.
If you are going from Leopard 10.5 up to 10.5.2, use Apple's combo updater which should appear in Software Update.

White Screen, Apple Logo, Spinner on startup after failed software update.

Hi, so my Macbook was performing poorly this morning and I decided I would try to install updates. The updates started normally, but around halfway through the bar stopped moving and the text underneath it said, "Running Installer Script." I left it alone for about three hours, came back, and saw that it was still doing the same thing. I decided it was time to try to reboot, and foolishly held the power button down for several seconds until it turned off. Upon turning it back on, I discovered that it would only go as far as the white screen with the apple logo and the thing spinning under it for about 20-30 seconds, then the screen will go black and it will try to start up again. I started it in verbose mode and it gives the following errors before crashing:
disk0s2 i/o error 0 [level 3] [readuid 0] [facility com.apple.system.fs] [errtype io] [errno 5] [iotype read] [pblknum 233675120] [lblknum 540]
disk0s2 i/o error 0 [level 3] [readuid 0] [facility com.apple.system.fs] [errtype io] [errno 5] [iotype read] [pblknum 233674536] [lblknum 467]
disk0s2 i/o error 0 [level 3] [readuid 0] [facility com.apple.system.fs] [errtype io] [errno 5] [iotype read] [pblknum 233674640] [lblknum 480]
I haven't tried booting from the disk because my disk drive has been broken for a while and needs to be replaced. I assume this problem is my fault, but I would very much appreciate anyone's input on how to resolve it.

Hello and welcome to Apple Discussions...
You would be better off posting in the Leopard v10.5 forum here.
Using Mac OS X Leopard
This is the Safari forum. Just copy/paste the same post over there.
While you are waiting for a response there, try the help here.
Resolve startup issues and perform disk maintenance with Disk Utility and fsck
You can get replacement system disc(s)...
Call Apple's Customer Support - in the US, (800) 767-2775 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.
Carolyn

Transferring data from my time machine after system software update, but my computer seems to be stuck on "create your account"

Have just been uploading snow leopard as the pre step to getting lion and have been transferring data from my time machine, but my computer seems to be stuck on "create your account"

I found a solution!
Perhaps this is just temporary, but I have my display up and working again.
Although the symptoms are different were a bit different, the solution here worked:
http://apple.stackexchange.com/questions/120259/grey-screen-after-login-blue-scr een-of-death-from-cmdr
As I was able to connect to my HD via an external monitor, in the finder, I went to:
1. Macintosh HD --> System --> Library --> Extensions
2. From there I moved all of the files that started with ADM and ATI (19 in total for me) to a folder on my desktop. (You will need to enter your admin password for this)
3. Next was a restart.
4. Then my display started working again.
5. After that, I transferred the files back into my Extensions folder.
6. I then did another restart with my fingers crossed and breath held. It worked.
Also... During the last few days of trying to find a fix, I restored a Mavericks backup to my computer away from Yosemite.
I'm very sure this problem occurred when I put my MBP to sleep, disconnected the power in its sleep, while something was connected to a USB port and unplugging the USB device (for me an iPhone charger) while the MBP was closed.
I hope this helps the next person.

Macbook Pro Retina display says "No batteries available" after legitimate system software update

Issue Description
On July 26, 2012 I placed an order with Apple store for the 15-inch MacBook Pro with Retina display with the following configuration (Order # W269108641 Serial# C02J52S9DKQ5):
Processor 2.6GHz Quad-core Intel Core i7, Memory 16GB 1600MHz DDR3L SDRAM, Flash Storage 512GB Flash Storage
It was delivered August 8, 2012. It cost me $3,265.16
I have since equipped it with accessories like a wireless apple keyboard ($69), wireless mouse ($69), USB super drive ($79), VGA display adapter ($29), Ethernet Adapter ($29) and the excellent sleeve/pouch from Pack & Smooch GmbH (GBP60))
It's so heavily configured because it’s my main workstation. I additionally bought and installed Parallels 8 so I can run Windows 8 in a Virtual Machine because I have a few things on Windows that I need to be productive. This setup has been a dream machine until a little over a week ago.
In the one year since I bought it, I have had only 2 issues;
• A case of display flickering that resulted after a system software update on August 28, 2013
(Case ID 498560320 - not much help came from Apple Support but fortunately the problem went away a week later after another system software update)
• A case of battery failure that resulted after a system software update on October 11, 2013
(Case ID 516534003 - I have gone through all recommendations from Apple support as I will detail below)
Symptoms after system software update
• Battery Icon on status bar disabled with a message "No batteries available"
• Battery not charging
• LED on the Magsafe power adapter no longer show
• Keyboard backlights no longer show
• Notebook fan loud/noisy and permanently at high speed
• Date and time reset to a date in the past at each restart
• Notebook starts up the moment the Magsafe adapter is connected without waiting for power button to be pressed
• An update for "MacBook Pro Retina Display SMC Update 1.2" keeps appearing in Software Update
Recommendations from Apple Support
• Perform SMC Reset (http://support.apple.com/kb/HT3964)
(Done - no change in status)
• Run Disk Utility
(Done - no errors found)
• Run Apple Hardware test (http://support.apple.com/kb/HT1509)
(Done - no errors found, no change in status)
• Visit Apple Store
(Done - they confirmed no issue with Magsafe adapter. For a fee they are happy to change the battery if confirmed faulty and re-install the OS if the battery is not the issue but am uncertain that the OS re-install will resolve the issue because I have read online about a similar case where a re-install did not resolve the issue)
• Check System Report/Hardware/Power
(Done - Health Information/Cycle count:0, Battery installed: No)
• Perform NVRAM Reset (http://support.apple.com/kb/HT1379?viewlocale=en_US)
(Done - no change in status)
Comments and additional Observations
Please note the following;
• All of the symptoms above appeared after a system software update on October 11, 2013
• This update first appeared on October 10, 2013 but I was too busy to apply it especially because it required a system restart
• The battery was fully charged when I decided to apply the update on October 11 morning after I got to work
• Normally on full charge, the battery will typically deliver 3 - 4 hours depending on usage and up to 6 hours when idle
• The said update was not interrupted or anything of the sort
• On the day the symptoms were first observed when I first logged the case with apple, the system ran on battery while it performed the Apple Hardware Test while I was driving to the Apple support store on my way home even though the status bar was indicating "No battery available"
I make the following deductions solely based on my observations
• An apple authorized system software update broke the system
• The nature of the failure is communication related - the battery charging circuit and related systems are not getting the necessary instructions to function as they should (It's a known fact that rechargeable batteries do NOT die instantaneously, the total hours they run on full charge will gradually reduce over time as they degrade on use)
• It’s possible the update is not being applied correctly because the item “MacBook Pro Retina Display SMC Update 1.2” is still in Software update after subsequent attempts to apply it
• The high fan speed is nothing to do with high temperature or high processor load, according to the Activity Monitor utility the highest CPU utilization 1.9 – 4.7% is by kernel_task (PID 0) followed by activitymonitord at 1.8 – 2.2% (PID 481)
• The symptoms match what an SMC reset should resolve according to Apple documentation
• This is a known problem within Apple based on the documentation provided and the numerous similar cases reported online
Summary;
The system is running OS X 10.8.5
I have provided this detailed documentation in the hope that someone who understands this system can say exactly what is going on. It's meant to be a dream machine but now you can hear the fan from across a large room, the battery doesn't charge and is in fact not recognized so I lose data if the Magsafe adapter gets unplugged, and I have to reset the system date each time I restart the notebook.
I've used this notebook with utmost care for a little more than a year, this investment of over $3,500 could have bought 3 high end notebooks from DELL or HP but I chose Apple.
I have suffered untold loss in productivity in the last 10 days since this issue occurred, I respectfully request Apple to fix my notebook.

Issue Description
On July 26, 2012 I placed an order with Apple store for the 15-inch MacBook Pro with Retina display with the following configuration (Order # W269108641 Serial# C02J52S9DKQ5):
Processor 2.6GHz Quad-core Intel Core i7, Memory 16GB 1600MHz DDR3L SDRAM, Flash Storage 512GB Flash Storage
It was delivered August 8, 2012. It cost me $3,265.16
I have since equipped it with accessories like a wireless apple keyboard ($69), wireless mouse ($69), USB super drive ($79), VGA display adapter ($29), Ethernet Adapter ($29) and the excellent sleeve/pouch from Pack & Smooch GmbH (GBP60))
It's so heavily configured because it’s my main workstation. I additionally bought and installed Parallels 8 so I can run Windows 8 in a Virtual Machine because I have a few things on Windows that I need to be productive. This setup has been a dream machine until a little over a week ago.
In the one year since I bought it, I have had only 2 issues;
• A case of display flickering that resulted after a system software update on August 28, 2013
(Case ID 498560320 - not much help came from Apple Support but fortunately the problem went away a week later after another system software update)
• A case of battery failure that resulted after a system software update on October 11, 2013
(Case ID 516534003 - I have gone through all recommendations from Apple support as I will detail below)
Symptoms after system software update
• Battery Icon on status bar disabled with a message "No batteries available"
• Battery not charging
• LED on the Magsafe power adapter no longer show
• Keyboard backlights no longer show
• Notebook fan loud/noisy and permanently at high speed
• Date and time reset to a date in the past at each restart
• Notebook starts up the moment the Magsafe adapter is connected without waiting for power button to be pressed
• An update for "MacBook Pro Retina Display SMC Update 1.2" keeps appearing in Software Update
Recommendations from Apple Support
• Perform SMC Reset (http://support.apple.com/kb/HT3964)
(Done - no change in status)
• Run Disk Utility
(Done - no errors found)
• Run Apple Hardware test (http://support.apple.com/kb/HT1509)
(Done - no errors found, no change in status)
• Visit Apple Store
(Done - they confirmed no issue with Magsafe adapter. For a fee they are happy to change the battery if confirmed faulty and re-install the OS if the battery is not the issue but am uncertain that the OS re-install will resolve the issue because I have read online about a similar case where a re-install did not resolve the issue)
• Check System Report/Hardware/Power
(Done - Health Information/Cycle count:0, Battery installed: No)
• Perform NVRAM Reset (http://support.apple.com/kb/HT1379?viewlocale=en_US)
(Done - no change in status)
Comments and additional Observations
Please note the following;
• All of the symptoms above appeared after a system software update on October 11, 2013
• This update first appeared on October 10, 2013 but I was too busy to apply it especially because it required a system restart
• The battery was fully charged when I decided to apply the update on October 11 morning after I got to work
• Normally on full charge, the battery will typically deliver 3 - 4 hours depending on usage and up to 6 hours when idle
• The said update was not interrupted or anything of the sort
• On the day the symptoms were first observed when I first logged the case with apple, the system ran on battery while it performed the Apple Hardware Test while I was driving to the Apple support store on my way home even though the status bar was indicating "No battery available"
I make the following deductions solely based on my observations
• An apple authorized system software update broke the system
• The nature of the failure is communication related - the battery charging circuit and related systems are not getting the necessary instructions to function as they should (It's a known fact that rechargeable batteries do NOT die instantaneously, the total hours they run on full charge will gradually reduce over time as they degrade on use)
• It’s possible the update is not being applied correctly because the item “MacBook Pro Retina Display SMC Update 1.2” is still in Software update after subsequent attempts to apply it
• The high fan speed is nothing to do with high temperature or high processor load, according to the Activity Monitor utility the highest CPU utilization 1.9 – 4.7% is by kernel_task (PID 0) followed by activitymonitord at 1.8 – 2.2% (PID 481)
• The symptoms match what an SMC reset should resolve according to Apple documentation
• This is a known problem within Apple based on the documentation provided and the numerous similar cases reported online
Summary;
The system is running OS X 10.8.5
I have provided this detailed documentation in the hope that someone who understands this system can say exactly what is going on. It's meant to be a dream machine but now you can hear the fan from across a large room, the battery doesn't charge and is in fact not recognized so I lose data if the Magsafe adapter gets unplugged, and I have to reset the system date each time I restart the notebook.
I've used this notebook with utmost care for a little more than a year, this investment of over $3,500 could have bought 3 high end notebooks from DELL or HP but I chose Apple.
I have suffered untold loss in productivity in the last 10 days since this issue occurred, I respectfully request Apple to fix my notebook.

System 10.3.9 freezes at startup after installing Security Update 2006-007

I installed the security update 2006-007 this morning and upon restart everything froze once the words "login window starting" appeared.
I tried a bunch of troubleshooting suggestions from the support pages ("Your Mac won't startup in OS X - 10.3.9 or earlier") including starting in safe mode, single user mode and dumping login preferences, network prefs, reset certain priveleges. None of these solved the problem.
Is the only work around for this to re-install the system?
PowerMac g4 dual proc. Mac OS X (10.3.9)

Ed,
I admit to being somewhat perplexed by your experience. But let me ramble a bit here anyway.
My opinion is that problems of the sort that you are experiencing (freeze after a software update) are almost always due to some software problem. (I base this opinion to a large extent on the experiences of other people in these forums.) The fact that your system works okay with Tiger is consistent with this idea.
But, if it is a software problem, why did it not go way when you re-installed Panther? I am wondering how you did the re-install. Was it an Archive and Install? That is the easiest approach and the first one to try, but there are some things it cannot fix. For one, if user settings and preferences are maintained during the A&I and the problem is related to these settings or preferences, then the problem will remain. In that case, an Erase and Install would be needed to clear out everything. Of course, this also deletes all of your data, so it is something you do not want to do unless you have a backup (which you said that you have).
Another thing that an A&I cannot solve is corruption of the filesystem (computer loses track of where some files start and stop on the hard drive). This problem can usually be detected and often repaired by booting off your install CD and using Disk Utility to repair the disk. You said that you used Disk Utility but gave no other details. I take that to imply that you detected no problems. If there are problems and Disk Utility is unable to fix them, a more powerful utility can sometimes do the job, and sometimes there is no solution except to reformat the hard drive and re-install the operating system. This of course destroys all data on the drive.
If there were a hardware problem behind this, the most likely thing in my view would be some bad blocks on the hard drive. I am pretty sure that Disk Utility, as used above, will look for bad blocks and mask them out if any are found. You mentioned something about 1 Gig of RAM. I think that RAM is unlikely to be the culprit. Problems with RAM usually are manifested as more erratic behavior that what you are experiencing.
You have already exhausted many of usual tricks, so what are your options? It sounds like you do not want to buy a copy of Tiger just to fix this and I can understand that. So, you could go to more and more extreme versions of re-installing your software. By this I mean using your Panther install disks to do an Archive and Install, then to do an Erase and Install if the first did not work, then to reformat and do an install if the Erase and Install did not work. Before doing either of these last two step,s you want to be sure that you have backup that you know works. You have said that "re-installing Panther does not fix the problem" and also that you "haven't done a system restore". It is not really clear to me what you mean by re-installing Panther. Was this from a backup or from your install CD?
If you want to avoid a re-install from your install CD as long as possible, then my suggestion is to attempt to troubleshoot the problem further by booting into Single User mode (which I think you have done). Once you get the disk mounted, I would suggest looking in the system.log file for an error message. Once you have mounted the disk, you can look at the end of the system.log file with the command
tail /var/log/system.log
Look to see if any of the messages look like they might be indicative of a problem. If you see nothing, you can print out more lines by doing this:
tail -40 /var/log/system.log
which will cause the last 40 lines to be printed. If you see any message that might be hinting at a problem, post it back here and perhaps someone will get a clue. I should say at the outset that this way of doing things takes a lot of patience and is not guaranteed to provide a solution.
I hope this ramble helps a bit. I know your are frustrated and I hope you get a solution soon.
Rich

IPhoto won't open after most recent system software update

I have just installed the most recent system software update for iPhoto and now iPhoto will not open. I get an error message - see attached screen shot - and I have tried cmd + alt to get the option to rebuild which just re-opens the error report again. Really need help as can't afford to lose all my photo's!

Some people have fixed that by redownloading the 10.7.4 update and rerunning it.
Others have reinstalled the OS
Regards
TD

Macbook will not boot up after running Software Update (Couldn't fix it)

Hi there,
I also have been experiencing some problems after running Software Update (Security update + Java) a couple of days ago. Similarly to Jandaf (http://discussions.apple.com/thread.jspa?messageID=9000023) I have only the gray start up screen + Apple logo + gear wheel constantly rotating. Based on the information provided in this forum I have tried some procedures which didn't solved my problem so far. Below I describe I have tried:
1) I have booted using the installation DVD and run the disk utility. When performing the First Aid/Verify Disk I found some errors ('Invalid node structure'). But I couldn't fix the problem using disk repair (same problem 'Invalid node structure' 'Volume check failed'.
2) I also tried to boot in single user mode (command + s) to run fsck -fy. It didn't work. I got the following message (last 4 lines):
CSRHIDTTransitionDriver::probe: -s
CSRHIDTTransitionDriver::probe: booting in single user .. do not match
Extension "com.apple.driver.AppleUSBTCKeyboard" has no kernel dependency.
Extension "com.apple.driver.AppleUSBTCEventDriver" has no kernel dependency.
3) When trying to boot in safe mode. I got a grey screen with the following message:
'You need to restart your computer. Hold down the power button for several seconds or press the Restart button".
4) I also tried to 'Archieve & Instal'. Again no success. After reading the DVD the action is terminated because some errors (does not specify).
5) I also tried the 'German Medicine' (http://discussions.apple.com/message.jspa?messageID=8728797#8728797) (i.e. Connect the 'problematic MacBook' to my old G4 via firewire and reinstall the 2009-001 update). Again no success. The G4 cannot mount the MacBook hardrive.
I don't know what to do any more.
A) Can I resuscitate my old system? If yes how?
B) If not, can I at least save the data I have in my old HD?
C) Is it possible to format and reinstall the OS or is this this computer doomed?
Apologies for writing so many questions but I'm really freaking out!
Thank you.
B.

Hi BDAqua,
I did as you said and got a firewire backup drive (Seagate - FreeAgent Desk 500GB). I tried to make a carbon copy of HD but it seems that the copy had some problems. Below I report both the CCC and console logs:
1) "Cloning method: Backup everything
Delete items on target that aren't on the source: No
18:23:39 Enabling ownership on the target volume...
18:23:50 The target volume has ownership enabled.
18:23:50 The target volume has Access Control Lists enabled.
18:23:50 Authenticating...
18:23:50 Initiating synchronization engine...
18:23:51 Cloning...
18:31:20 rsync: readdir("/Applications/Utilities/Audio MIDI Setup.app/Contents/Resources/French.lproj"): Input/output error (5)
19:04:41 rsync: readdir("/System/Library/Components/AudioCodecs.component/Contents/Resources/Fr ench.lproj"): Input/output error (5)
19:05:41 rsync: readdir("/System/Library/CoreServices/Menu Extras/IrDA.menu/Contents/Resources/French.lproj"): Input/output error (5)
19:06:01 rsync: readdir("/System/Library/CoreServices/Menu Extras/User.menu/Contents/Resources/French.lproj"): Input/output error (5)
19:07:05 rsync: readdir("/System/Library/Extensions/IOUSBFamily.kext/Contents/PlugIns/AppleUSBC DCECMData.kext/Contents/Resources/French.lproj"): Input/output error (5)
19:10:13 rsync: readdir("/System/Library/PrivateFrameworks/Assistant.framework/Versions/A/Resou rces/French.lproj"): Input/output error (5)
19:50:10 rsync error: some files/attrs were not transferred (see previous errors) (code 23) at /Volumes/Home/Users/bombich/Development/Bombich_Software/rsync-3.0.5pre2/main.c (1047) [sender=3.0.5pre2] (51)
19:50:11 rsync: Some errors were encountered during the backup., Error code: 51
19:50:14 Sync Engine warnings: (
"rsync: readdir(\"/Applications/Utilities/Audio MIDI Setup.app/Contents/Resources/French.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/Components/AudioCodecs.component/Contents/Resources/F rench.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/CoreServices/Menu Extras/IrDA.menu/Contents/Resources/French.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/CoreServices/Menu Extras/User.menu/Contents/Resources/French.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/Extensions/IOUSBFamily.kext/Contents/PlugIns/AppleUSB CDCECMData.kext/Contents/Resources/French.lproj\"): Input/output error (5)",
"rsync: readdir(\"/System/Library/PrivateFrameworks/Assistant.framework/Versions/A/Reso urces/French.lproj\"): Input/output error (5)",
"rsync error: some files/attrs were not transferred (see previous errors) (code 23) at /Volumes/Home/Users/bombich/Development/Bombich_Software/rsync-3.0.5pre2/main.c (1047) [sender=3.0.5pre2]"
2) "Mac OS X Version 10.4.11 (Build 8S2167)
2009-03-01 10:30:14 +0100
2009-03-01 10:30:21.962 SystemUIServer[213] lang is:en
Mar 1 11:20:32 Bs-Home-Mac /usr/sbin/ocspd: starting
Mar 1 11:38:25 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 12:46:40 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 13:54:55 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 15:03:13 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 16:11:31 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 17:19:46 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Main starting
2009-03-01 17:47:20.393 Skype[313] SkypeApplication::init called
2009-03-01 17:47:21.554 Skype[313] SKInitDebugLogging
2009-03-01 17:47:46.169 Skype[313] SkypeSound::setAudioDeviceUID: cannot find audio device with UID (null), trying to use default system output device instead
2009-03-01 17:47:47.208 Skype[313] SkypeSound::setAudioDeviceUID: cannot find audio device with UID (null), trying to use default system output device instead
Starting the process...
2009-03-01 17:48:36.186 Skype[313] MacVideo getDimensions rc == NO, width 0, height 0
2009-03-01 17:48:36.367 Skype[313] MacVideo getDimensions rc == NO, width 0, height 0
2009-03-01 17:48:37.367 Skype[313] MacVideo getDimensions rc == NO, width 0, height 0
2009-03-01 17:48:37.369 Skype[313] MacVideo getDimensions rc == NO, width 0, height 0
2009-03-01 17:59:16.450 Skype[313] SkypeSound::setAudioDeviceUID: cannot find audio device with UID (null), trying to use default system output device instead
Mar 1 17:59:19 Bs-Home-Mac crashdump[355]: Skype crashed
Mar 1 17:59:20 Bs-Home-Mac crashdump[355]: crash report written to: /Users/bernardolima/Library/Logs/CrashReporter/Skype.crash.log
Mar 1 18:23:50 Bs-Home-Mac authexec: executing /Applications/Carbon Copy Cloner.app/Contents/Resources/helper_tool
Mar 1 18:28:01 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Main starting
2009-03-01 18:41:03.154 Skype[393] SkypeApplication::init called
2009-03-01 18:41:12.433 Skype[393] SKInitDebugLogging
Mar 1 19:36:16 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 19:55:54 Bs-Home-Mac mdimportserver[480]: -[ABAddressBook sharedAddressBook] Can't ABACQUIREFILELOCK Framework/AddressBook/ABAddressBook.m:2746
Mar 1 19:57:12 Bs-Home-Mac mdimportserver[480]: * +[NSUnarchiver unarchiveObjectWithData:]: extra data discarded
Mar 1 19:57:12 Bs-Home-Mac mdimportserver[480]: * +[NSUnarchiver unarchiveObjectWithData:]: extra data discarded
Mar 1 20:44:34 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 21:52:51 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor
Mar 1 23:01:07 Bs-Home-Mac ntpd[191]: sendto(17.72.255.12): Bad file descriptor"
Due to my lack of knowledge I can't judge how bad this is. But I can tell you that every time I read the word bad in the log it scares the s*** out me.

ITunes won't open after downloading software update. Macbook Pro OSX10.6.8 Simple solution?

iTunes won't open after downloading software update. Macbook Pro OSX10.6.8 Simple solution? And by the way, this is apparently a common problem and Apple has completely failed to warn in advance or offer a quick straightforward solution - used to be a good company, but it's becoming just another crappy screw-the-consumer corporation.

It would help to know versions here. I'm guessing your update put an older version of something into a place where a newer version of something iTunes put in there existed. Updating an earlier OSX version to 10.6.8 is still only updating to system software that was issued several years ago. If you are running some slightly newer version of iTunes issued subsequent to 10.6.8 and you just updated to 10.6.8 you may have put in an older version of something iTunes uses. Anyway, I'm guessing here until we know exactly what you did.

After running Software update, I can no longer run, open, sync or use iTunes in any way. PLEASE what happened??

I was running the newest version of Snow Leopard, and after running Software update, I can no longer run, open, sync or use iTunes in any way. PLEASE what happened?
I really regret that I said "OK" to Software Update message... after Software Update of these updates on 7-26-11:
Migration Assistant Update for Mac
Mac OSX 10.6.8 Supplemental Update
Safari
iTunes
Remote Desktop Client Update
Now I get a message:
iTunes cannot be opened because of a problem
Check with developer to make sure iTunes works with this version of Mac OSX. You may need to reinstall the application. Be sure to install any available updates for the application and Mac OSX.
Process:         iTunes [5092]
Path:            /Applications/iTunes.app/Contents/MacOS/iTunes
Identifier:      com.apple.iTunes
Version:         ??? (???)
Build Info:      iTunes-10315501~1
Code Type:       X86 (Native)
Parent Process: launchd [111]
Date/Time:       2011-07-26 12:08:18.568 -0500
OS Version:      Mac OS X 10.6.8 (10K540)
Report Version: 6
Interval Since Last Report:          504736 sec
Crashes Since Last Report:           20
Per-App Crashes Since Last Report:   13
Anonymous UUID:                      B8B5EE28-970A-4E79-949B-EA2DD6E6DAA2
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Crashed Thread: 0
Dyld Error Message:
Library not loaded: @loader_path/libgnsdk_musicid.1.8.2.dylib
Referenced from: /Applications/iTunes.app/Contents/MacOS/iTunes
Reason: image not found
Binary Images:
0x8fe00000 - 0x8fe4162b dyld 132.1 (???) <A4F6ADCC-6448-37B4-ED6C-ABB2CD06F448> /usr/lib/dyld
Model: Macmini3,1, BootROM MM31.00AD.B00, 2 processors, Intel Core 2 Duo, 2.26 GHz, 2 GB, SMC 1.35f1
Graphics: NVIDIA GeForce 9400, NVIDIA GeForce 9400, PCI, 256 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x90), Broadcom BCM43xx 1.0 (5.10.131.42.4)
Bluetooth: Version 2.4.5f3, 2 service, 19 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Serial ATA Device: Hitachi HTS543216L9SA02, 149.05 GB
Serial ATA Device: OPTIARC DVD RW AD-5680H
USB Device: External HDD, 0x1058 (Western Digital Technologies, Inc.), 0x0704, 0x24100000 / 2
USB Device: Hub, 0x0424 (SMSC), 0x2507, 0x26400000 / 2
USB Device: iMic USB audio system, 0x077d, 0x07af, 0x26440000 / 4
USB Device: Hub, 0x0424 (SMSC), 0x2502, 0x26470000 / 3
USB Device: Deskjet D4300 series, 0x03f0 (Hewlett Packard), 0x1f04, 0x26471000 / 5
USB Device: GD-0608-U, 0x056a (WACOM Co., Ltd.), 0x0021, 0x04700000 / 4
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0x04500000 / 3
USB Device: Hub in Apple Pro Keyboard, 0x05ac (Apple Inc.), 0x1003, 0x04300000 / 2
USB Device: Apple Optical USB Mouse, 0x05ac (Apple Inc.), 0x0307, 0x04310000 / 6
USB Device: Apple Pro Keyboard, 0x05ac (Apple Inc.), 0x020b, 0x04330000 / 5
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x06100000 / 2
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8216, 0x06110000 / 5
FireWire Device: unknown_device, Unknown
FireWire Device: d2 DVDRW FW, LaCie, Up to 400 Mb/sec

Same thing happened to me and I get the same error message. These are the programs that don't work
mail
keynote
pages
all Office 2011 programs
safari

Macbook will not boot up after running Software Update

My MacBook will not boot up after running Software Update (Security update + Java?) earlier today. I have only the gray start up screen + Apple logo + gear wheel constantly rotating. I have tried restarts several times and tried to start up from my original system DVD - this makes no difference.
I called Apple support, tried resetting the power and PRAM - still no difference. He had no knowledge of other problems reported; although I note recent post may have same issue.
I cannot get an appointment at my Apple Store before Monday.
Any suggestions?

Still no success. When I hold down the option key when powering up I get the hard disk icon plus arrowhead (only). When clicking the arrowhead it goes to the gray screen + apple logo+ rotating gearwheel.
This happens both with DVD in slot and without DVD. the DVD image is not coming up on screen. When I start up without DVD the hard disk icon appears promptly. When I start with DVD in the DVD is spinning for a short period before the hard disk icon appears. On clicking the arrowhead to hard disk icon the DVD spins again for a while then stops. Apart from the DVD spinning, both situations result in gray screen + apple logo+ rotating gearwheel.

Time capsule stopped working after installing software update, no lights and reset did nothing. What do I do?

I can't get my time capsule to turn on after a software update. Reset button does nothing and it is pluged in to a live outlet. Is my time capsule dead?

Welcome to Apple Discussions, Freepisces
I have all the latest updates on my Macs, and I have no problem at all.
If you applied the latest (7.4.1) QT update, your problem may be due to the fact that the System Requirements for QuickTime 7.4.1 for Tiger include Mac OS X 10.4.9 or later, and you show that you are using Mac OS X (10.4.3). You can check which QT version you have installed using the QuickTime Player > About QuickTime Player menu command.
If your QT version is an older one that is compatible with your Mac OS, and if you have not done so since you applied the QT update, repairing permissions may help you.
If the problem is somehow related to your iSight rather than to your QT software, Apple's How to Troubleshoot iSight may help you identify and fix your problem.
Unless you have a compelling reason for not doing so, you should consider updating to the latest version of Tiger (10.4.11). To find out what improvements you are missing by staying with 10.4.3, see some of the "About the Mac OS X 10.4.xx Update" documents for updates later than 10.4.3. A couple of examples are:
• About the Mac OS X 10.4.6 Update (combo) and
• About the Mac OS X 10.4.11 Update
If you are interested, other "About..." documents are linked in this search list.
Because System Requirements for the latest combo applicable to your MacBook, Mac OS X 10.4.11 Combo Update (Intel), are for Mac OS X 10.4.4 or later, you will need at least two steps to upgrade from your Mac OS X (10.4.3), so pay careful attention to the System Requirements of any updates you plan to apply.
EZ Jim
PowerBook 1.67 GHz w/Mac OS X (10.4.11) G5 DP 1.8 w/Mac OS X (10.5.1) External iSight

IPad mini will not let me access mail after latest software update, 6.1.2, seems to want me to sign in, but whenever I type my Id ad password it just says that the mail account already exists.. Still can't open my mail!

iPad mini will not let me access mail after latest software update, 6.1.2, seems to want me to sign in, but whenever I type my Id ad password it just says that the mail account already exists.. Still can't open my mail!
Help would be appreciated.

PhotogYogi wrote:
I Have the same issue on a brand new iPad mini 2. My battery is only lasting up to 5 hours. I went on chat with Apple last night and they said my battery is fine and its a Safari issue. I'm literally losing 1% every 3-4 minutes. I tried recalibrating my battery, signing out of iCloud, shutting off all locations, turning off background app refresh, restoring network settings, restoring all, and finally restoring from iTunes with no luck. This is just awful. I got this iPad so I could use it on my long flight for a trip I have coming up, and unfortunately, it's not going to last that long, plus I'm concerned about how many times i will be recharging my battery because of this since battery's do have a life cycle dependent on the number of charges. This is frustrating and needs to be fixed ASAP and addressed by Apple.
By the way, Apple told me to bring my device to the Apple Store because it's still under warranty. That's great and all, but I'm going to waste my time if there is no fix for this issue.
Ok so you want Apple to address the problem, but yet you don't want to take it to them just in case they can't fix it? What if they can fix it? Complaining here certainly won't fix it.

My ipod 4th gen can't be recognized by itunes after itouch software update

my ipod 4th gen can't be recognized by itunes after itouch software update. I have reset both PC and itouch to no avail

http://support.apple.com/kb/TS1538

No Startup After System Software Update

Similar Messages

Maybe you are looking for