No Time Capsule connection after 10.6.1 update

Updated to Snow Leopard 10.6.1 last night on my iMac. It no longer sees my time capsule as a shared server nor does it see it as an airport for internet connection. The TC is working, my MacBook (which I have not updated) works flawlessly with the TC.

You are not alone:
http://discussions.apple.com/thread.jspa?threadID=2149690&tstart=0

Similar Messages

Time Capsule down after 7.4.1 update

After sucesssfully updating to 7.4.1, Time Capsule goes down after roughly 20 hours.
The light stay green, airport net is still seen by computers, but you can't join it. You can't connect either through Ethernet. No ping
No reset possible either !
Only solution is pluging out the power and rebooting
My Macpro has a 802.11 n card
I have also a slimdevice and a wifi canon printer
All 3 are connected in 802.11b/g , which seems odd to me

FYI- I figured out how to download old firmware versions. I figured I would post it here in case someone else is having the same problem.
From the menu bar, while holding the Option key down, select Airport Utility -> Check for Updates… You’ll see a list of all the old and new firmwares which are available. Select the version you want for your Airport (note different Airports have different firmwares.) After downloading 7.3.2 for your Time Capsule/Airport. After the download is complete, select the device you want to upgrade (or in this case, downgrade) and click Base Station, then Upload Firmware. The version(s) that you download should be in the drop down menu.

Back up is very slow on 2 tb time capsule. After 2 days only 60 gb of 320 gb completed. Have connected ethernet cable. Any suggestions?

Back up is very slow on 2 tb time capsule. After 2 days only 60 gb of 320 gb completed. Have connected ethernet cable. Any suggestions?

Yes, that's terribly slow. You should get somewhere in the neighborhood of 20-24 GB/hour via Ethernet, assuming there isn't a lot of conflicting network traffic or your Mac's CPU is under very heavy load.
Are you sure you're actually using the Ethernet connection, instead of WIFI? To check, turn Airport off. If the backup fails, it's on WIFI. In that case, you need to set Ethernet as the "preferred" network, via System Preferences > Network. Click the "gear" icon at the bottom of the sidebar and select Set Service order. Then drag Ethernet above Airport. When both Airport and Ethernet are on, that will make OSX select Ethernet over Airport.
If that doesn't help, see #D2 in Time Machine - Troubleshooting.

External hard drive is not working on airport time capsule even after 7.7.2 firmware update.

External hard drive is not working on airport time capsule even after 7.7.2 firmware update.
I have the latest Airpor Time capsule 2gb. I specifically bought it so that I could have an external hardrive set up to wirelessly house my itunes library and movies. When i connect the drive, all i get is that the disk needs to be repaired.
the drive can works fine when connected to the macbook pro and I have run the verify and repair features in disk utility. I have also reset the airport timecapsule as well following these changes and still no change.
The 7.7.2 update says that it addressed the usb issue of not showing the drives but there are still problems as I cannot get it to appear.
Please help.
Thanks

How is the hard drive formatted?
Have you tried using a powered USB hub with the drive when it is connected to the Time Capsule?
(The USB port on the Time Capsule is borderline as far as power is concerned....you may need to use a powered hub.....even if the hard drive has its own power supply)
If the drive is formatted correctly....and....it has ample power, it will "show up" when you open AirPort Utility, click Edit, then click the Disks tab at the top of the next window.
In the example below, my Time Capsule drive is named "Backups" and another drive named "WD Drive" is connected to the USB port on the Time Capsule.
You should see the name of your Time Capsule drive (named "Data" unless you have changed the name) and the name of the USB drive if you perform the same check.
What do you see?

Time capsule problems after OS reinstall

After getting a blue screen on restart I had to do an archive/OS reinstall today. The reinstall worked fine but I am now having problems accessing my Time Capsule.
At first my computer didn't even recognize my time capsule. After restarting my time capsule, my computer recognized it. However, when I tried to open time machine to access the files, it stalled on "connecting to backup volume" for about 45 minutes and never connected. Similarly, the backup stalls on "preparing backup." I tried to stop backing up but it is currently stalled on "stopping backup." Finally, time capsule has disappeared from the menu at the top of my screen.
Any thoughts on addressing these issues would be greatly appreciated.

I have the same problem as well. I did an archive and install with OSX, then updated to 10.5.5 and now all the TC does is spin and say preparing. A sample from the console is
Nov 12 09:46:11 Macintosh /System/Library/CoreServices/backupd[204]: Waiting 60 seconds and trying again.
Nov 12 09:47:27 Macintosh /System/Library/CoreServices/backupd[204]: Network volume mounted at: /Volumes/Erik Elie's Time Capsule
Nov 12 16:01:05 Macintosh /System/Library/CoreServices/backupd[204]: Failed to mount disk image /Volumes/Erik Elie's Time Capsule/Erik Elie’s Computer_0017f2ccba9f.sparsebundle (DIHLDiskImageAttach returned: 109)
Nov 12 16:01:05 Macintosh /System/Library/CoreServices/backupd[204]: Waiting 60 seconds and trying again.
Nov 12 16:01:06 Macintosh /System/Library/CoreServices/backupd[204]: Ejected Time Machine network volume.
Nov 12 16:02:08 Macintosh /System/Library/CoreServices/backupd[204]: Network volume mounted at: /Volumes/Erik Elie's Time Capsule
Nov 12 16:04:10 Macintosh /System/Library/CoreServices/backupd[204]: Failed to mount disk image /Volumes/Erik Elie's Time Capsule/Erik Elie’s Computer_0017f2ccba9f.sparsebundle (DIHLDiskImageAttach returned: 60)
Nov 12 16:04:10 Macintosh /System/Library/CoreServices/backupd[204]: Giving up after 3 retries.
Nov 12 16:04:16 Macintosh /System/Library/CoreServices/backupd[204]: Backup failed with error: 21
Nov 12 16:43:53 Macintosh /System/Library/CoreServices/backupd[204]: Starting standard backup
Nov 12 16:43:53 Macintosh /System/Library/CoreServices/backupd[204]: Network volume mounted at: /Volumes/Erik Elie's Time Capsule
Nov 12 16:44:08 Macintosh /System/Library/CoreServices/backupd[204]: Failed to mount disk image /Volumes/Erik Elie's Time Capsule/Erik Elie’s Computer_0017f2ccba9f.sparsebundle (DIHLDiskImageAttach returned: 109)
Nov 12 16:44:08 Macintosh /System/Library/CoreServices/backupd[204]: Waiting 60 seconds and trying again.
Nov 12 16:44:09 Macintosh /System/Library/CoreServices/backupd[204]: Ejected Time Machine network volume.
Nov 12 16:45:10 Macintosh /System/Library/CoreServices/backupd[204]: Network volume mounted at: /Volumes/Erik Elie's Time Capsule
Nov 12 22:09:24 Macintosh /System/Library/CoreServices/backupd[204]: Failed to mount disk image /Volumes/Erik Elie's Time Capsule/Erik Elie’s Computer_0017f2ccba9f.sparsebundle (DIHLDiskImageAttach returned: 109)
Nov 12 22:09:24 Macintosh /System/Library/CoreServices/backupd[204]: Waiting 60 seconds and trying again.
Nov 12 22:09:25 Macintosh /System/Library/CoreServices/backupd[204]: Ejected Time Machine network volume.
Nov 12 22:10:26 Macintosh /System/Library/CoreServices/backupd[204]: Network volume mounted at: /Volumes/Erik Elie's Time Capsule
Any suggestions out there??

Time Capsule Connection Help Needed (Flashing Amber)

Guys,
I've been trying to troubleshoot my Time Capsule connection for a week now and I have had zero luck.
I have a Imac with OSX 10.6.8 that uses AirPort v 5.6.1. I have a Cat-5 (ethernet cable) plugged from my Time Capsule port (looks like this <-->) into an available port in my cable mode/router. My Imac is also plugged into this router. The two cat-5 (ethernet) cables are side by side.
So....
Every time I plug in the Time Capsule I get the following prompt via AirPort.
AirPort Utility found a Time Capsule 802.11n (4th Generation) that is
reporting problems.
Time Capsule's Name : My Capsule
          IP Address: 10.0.1.1
          Versino: 7.6.1
          AirPort ID: 12:88:93:CC:FF:72
If this is not the AirPort wireless devise you want to setup you can select another from the list on the left. If you don't see it make sure.... Blah blah blah....
To make a long story tollerable I do see my Time Capsule on the left at the top. Its the only one and its selected by default. So I do the next logical thing right? I click "Continue" and AirPort reads the Time Capsule's configuration.... and then...... I get the error
An error occurred while reading the configuration.
Make sure your Apple Wi-Fi base station is plugged
in and in range of your computer or connected via
Ethernet and try again. (-6753)
Can anyone help me understand why I can grab the Time Capsule's IP Address but AirPort can not read the hardware's (Time Capsule) config?
I'm at a loss.
Could my ethernet cable be the issue?

Hackintosh,
Thanks man... Yes, I plugged it into the circle symbol with no joy. I also went to Wal Mart and baught a new seven foot cat-5 for $10. Again I still have the flashing amber light.
After plugging in the ethernet cable into the circle icon port AirPort returns the following prompt.
I reset the TC (ball point pen to the reset hole untill fast blinking amber light occurs) and entered the needed params and it returns this error.
An error occured close the configuation window and try again.
It must be a config parameter that I'm setting incorrectly. There's a bunch so who knows what I'm doing wrong.
I just need the to talk to my Imac so i can get a backup executed. A wireless connection will take too long.
FYI: The cat-5 is brand new and is 100% functional (green light on the TC and router.)

I did a backup from all my files saved in old external hd to time capsule. After that double checked and recover one file from TC to mac air and it worked just perfect. Today went through TC to recover another file and none of them were there?

I did a backup from all my files saved in old external hd to time capsule. After that double checked and recover one file from TC to mac air and it worked just perfect. Today went through TC to recover another file and none of them were there?Anybody has a clue what happened?

renatocremonese wrote:
I want to use it for backing up my Mac.
It's good for that . . .
But also I don't keep all my stuff in my Mac.
But not for that.
This older and not day-by-day usage files I want to store in the time machine.
You can do that (see below), but how are you going to back them up? If your only copies are on the TC, when (not if) it fails, you risk losing your only copy of the data.
Is it possible to split TC in two partitions.
No, but there are some workarounds, including making a fixed-size disk image on it to "reserve" some space. See #Q3 in Using Time Machine with a Time Capsule.
But you still won't have backups of the stuff you put there.
You don't say what kind of Mac you have. If it's a desktop model, just keep the external HD connected to it, and let Time Machine back it up along with your internal HD.
However, it sounds like you may have a laptop, where that's not going to be convenient. In that case, your best bet might be to copy the external HD to a disk image on the TC as above, then keep the HD in a safe place.
To finish, when i enter the TC and go through the Time line how can I get a file from there and move it back to Mac hd.
Via the "Star Wars" display, per #15 in Time Machine - Frequently Asked Questions.
You might also want to review the Time Machine Tutorial, and perhaps browse the rest of the FAQ.

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260

How to improve quality of time capsule connection signal?

how to improve quality of time capsule connection signal?
i have one time capsule in Ground floor but the signal is very weak in the first floor? how can i improve the Quality internet signal???

wassimfrombeirut wrote:
Dear LaPastenague
Thank you for your reply
i just need to ask you a question; i am a new system admin using mac.
i need a software that can manage my internet bandwidth; qouta; and restriction to facebook; youtube and other web
could you guide me to a software i can use????
note that my environment is fully mac laptop; and using Time capsule as Wi Fi source to connect to enternet.
thank you;
best regards
wassim;
The best software to do what you want, is not on a Mac. It is a router.. gargoyle.
You can keep using the TC as wifi source but get a router that can can take gargoyle firmware.. the best in my testing is netgear WNDR3700. Gargoyle itself is a free download.
http://www.gargoyle-router.com/download.php
There are other routers and router boards it will work on.. but make sure you pick something compatible. I have used several different routers and the one above is the best so far.

HT1178 My time capsule wants to down load an update (1st update) and error 6727 comes up and it won't download the update. What is the problem and how do I fix it?

My Time capsule wants to down load an update (1st update) and an error of 6727 shows up and it won't down load the update. What is the problem and how do I fix it?

I have done it before.. but other than saying it worked there was no other indication.
https://discussions.apple.com/message/22042667#22042667

No connection to Time Capsule router after restoring backup

I had a hard disk failure in Macbook Pro and the disk was replaced with fresh Yosemite 10.10. The Macbook Pro had Mavericks before the crash. I use a Time Capsule as router for several laptops, Ipads and mobile phones and for Time Machine backups and it works fine. Restoring the system from Time Machine backup to the Mackbook Pro by WiFi went fine. Took some 7-8 hours overnight. The problem with the Macbook Pro is now that it cannot locate the Time Capsule either with WiFi or Ethernet connection and cannot connect to internet. I can detect the restored Macbook Pro using the Airport Utility of a Macbook Air with OS 10.7.5. I can detect the Time Capsule and even modify its settings using the Airport Utility of the Macbook Pro by using the Time Capsule address. But the Airport Utility of the Macbook Pro still keeps on searching the configured base station, that is the Time Capsule. So, this is not a hardware problem, but some settings in the Macbook Pro. Any ideas?

What are you using to connect to it?
Do a full factory reset and plug in by ethernet to do the setup.
Reset instructions here.
http://support.apple.com/kb/HT3728

Can't connect to old Time Capsule data after installing Lion

I recently installed Lion, and when I set up Time Machine to my old Time Capsule I've been using since TCs were released, and the software only shows data as if I've never backed up before, as well as saying "Oldest Backup" and "Latest Backup" as "none." I have used this TC through Leopard and Snow Leopard, and there is lots of old backups on the drive. The TC storage amount shows 91 of 500 GB available, so I know my data is still there. I need TM to recognize the old backup data on the TC so I can access some old backups I have. Please help if anyone knows what to do here!

Mount the "Data" volume of the Time Capsule and look at the dates of the "sparsebundle" files there. If there seem to be two there for your MacBook Pro, then your old data is still there in the older backup. To see that data, click-and-hold or control-click on the Time Machine icon and select "Browse Other Time Machine Disks".

I have a time capsule connected directly to fiber connection. I have connected a windows server directly to TC and configured it for remote desktop connection. From my interanet I can access srvr but not from my home. What config I need on TC?

I have a time capsule directly connected to fibre optic point out. All pcs and macs are connected wirelessly to the internet. I have connected a windows server pc to TC. When configured for Remote desktop connection, I can access windows server from within interanet but don't know how to access it from internet. I guess I need to change some settings in TC to get some ip adress for the remote desktop connection from my home. Anyone who can help me out? Appreciate it.
Narmin

I am a little lost now.. I have read again your title and your first post.. and they seem inconsistent.
In the title you state.
From my interanet I can access srvr but not from my home.
Interanet is not a word I know.. I assumed intranet...are you talking about internet or intranet? And just to be clear say WAN or LAN.. !! Is your home part of the interanet??
In the first post you state,
I can access windows server from within interanet but don't know how to access it from internet.
Now this is more normal.. the issue is not in the home at all, it is accessible from there but fails from internet. If this is correct, then you can do a few obvious things to determine where the problem is.
But first I need to know are you actually testing from a different internet connection to your home lan.. you are not just trying the public IP from inside the LAN as that will fail due to the TC not doing NAT Loopback.
I am also assuming the TC is the only router in the network, and has the public IP on the WAN interface.
And I am also assuming you have turned on the ping responder and you can actually ping your public ip from the internet and get a response. This helps no end in figuring out where there are issues. Strange but I have no idea if there is a ping responder in the TC WAN so you might need to forward that as well. Also if you have a dynamic public ip address are you using dyndns or no-ip or some other service to connect.
1. Test bypassing the TC.. plug the internet connection straight into the windows server,, and test if you have access. If yes, the TC is the problem.. if not, your setup on the windows server is wrong.. look at firewall in particular.
2. Assuming from test 1 the TC is the problem, Post the screen shots of the port forwarding setup for us to look at.. that is by far the easiest way to check it out.
There are lots of references to port forwarding in the TC.. eg
http://must-know-mac.blogspot.com/2008/07/how-to-port-forward-time-capsule.html
The things that generally go wrong are firewall on the computer that is accepting the port.
The ISP doesn't allow connections on a particular port. (not likely in your case)
The router is behind another router.. double NAT will kill any port forward.
Upnp has already allocated a port.. not an issue as TC doesn't use upnp although a reboot of everything after you set port forwards is well worth it.. amazing how things don't stick properly without a reboot.
IP on the receiving device is not static and so changes.
Not enough or right type of ports are opened. This is always messier than it looks as one port is often not enough for two way communications.

Time capsule problems after installing Lion

After installing Lion, I need to regularly shut down iMac(Intel) in order to have Time capsule do the next backup. This method allows me to manually back up the automatic function to back up no longer exists. Also unable to connect to the backup disk.

Mine needs backing up immediately after its just backed up!! Its crazy!! IOS5 was supposed to be free but as a result I had to pay to upgrade to Lion then I had to pay to upgrade to iPhoto 11 just to be able to transfer photos from my iphone!! On top of this, Lion runs as slow as a PC, asks to backup constantly, I'm losing iDisk and iWeb next year and they've removed the bounce facility from Mail. Blinding. Well done Apple - who's brainwave was Lion and IOS5? Bill Gates?

Time capsule -connecting, backup, file transfer

hello,
i am very new to time capsule, and have the following issue i would like to get solved/understand:
1. when i want to access my time capsule disk through the normal finder window, clicking on the time capsule icon to the left, it appears that finder tries to connect, but then i get a connection failed message. only when i access it through go>connect to server> etc, it appears as a disk. Now I would like to know, if the connection established that way (through connect to server) is actually connecting via internet, instead of using the direct wireless connection to the disk (I'm sitting right next to my time capsule)?? In the case it is using the internet to connect my time capsule, for sure my connection to the disk should speed up, as soon as i get the connection through wireless, isn't it? For the rest everything works just fine, internet connection wirelessly with airport, etc.
2. I am transferring data from an old backup disk to my new timecapsule. i have this old disk connected to mac my through usb, and drag n dropped the files on the time capsule. the copying process is fairly slow, but still faster than connecting the old disk directly to the usb slot on time capsule. Is there any way of directly transferring data through the usb slots from my old disk to my time capsule? it would be so much faster.....
thanks in advance...

Welcome to Apple Discussions!
majajaja wrote:
hello,
i am very new to time capsule, and have the following issue i would like to get solved/understand:
1. when i want to access my time capsule disk through the normal finder window, clicking on the time capsule icon to the left, it appears that finder tries to connect, but then i get a connection failed message. only when i access it through go>connect to server> etc, it appears as a disk. Now I would like to know, if the connection established that way (through connect to server) is actually connecting via internet, instead of using the direct wireless connection to the disk (I'm sitting right next to my time capsule)?? In the case it is using the internet to connect my time capsule, for sure my connection to the disk should speed up, as soon as i get the connection through wireless, isn't it? For the rest everything works just fine, internet connection wirelessly with airport, etc.
Hmmm... my Time Capsule folder resides in my Shared Folder under Finder. It mounts a few seconds after I click on it. I've never had to +connect to server+.
2. I am transferring data from an old backup disk to my new timecapsule. i have this old disk connected to mac my through usb, and drag n dropped the files on the time capsule. the copying process is fairly slow, but still faster than connecting the old disk directly to the usb slot on time capsule. Is there any way of directly transferring data through the usb slots from my old disk to my time capsule? it would be so much faster.....
Unfortunately, you will not be able to continue to use this Time Machine backup in this manner. TM utilizes a sparsebundle when backing up to a NAS (Time Capsule) which is very different from a backup into a folder structure if the HDD is connected directly to your Mac (USB HDD). Your TM back ups will still be available on your USB HDD, but you are better off starting an entirely new backup on TC.
Good luck!

No Time Capsule connection after 10.6.1 update

Similar Messages

Maybe you are looking for