No vga new viedo card,mother board,power supply and cable

persario sr550r no vga signal on monitor,new cable,new power supply,new viedo card,new mother board,still no vga signal,I have tested monitor it is good?Do you need to remove any viedo chip when installing new viedo card?I can rebuild a car from ground up!This computer is kicking my butt! help!!!

Terkemoma, welcome to the forum.
Don't let the computer KYB! We'll solve the problem.
First, however, I believe that there is another number in the model of the computer. Once I have the full model I will see what I can do to help you.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Similar Messages

LEOPARD, BATTERIES, POWER SUPPLY and other power issues

Hello ALL!
Happy New Year!
In fact I feel a bit scary last two days. Never had this kind of feeling since LB replaced :-D My scare related to the topics i've read here about batteries and leopard. Later below i will write my questions specific.
I just summarise my problem:
1. With battery installed unplug from mains leads to instant shutdown like it is some desktop.
2. The battery now does not have LED indication at all even in system it comes up as 100 charged and System Profiler reads information from battery.
3. When In unplug the laptop from mains first time, the battery did not give any indication of level of charge before i plug it in mains, after that it started charging and system indicator was trying to calculate remaining time till the end of charge endless...
4. This battery was working fine since 3 years without significant reduction in capacity. Before yesterday it was enough power to watch 2-2.5 hours DVD.
5. Battery seem to be dead. Mind that it was no slow reduction in capacity (keeping charge)
6. I was making calibration with some regularity.
7. While sleep mode with leopard seems battery drains faster even for me seems general operation after upgrade became longer.
So my questions are:
1. Is my battery really dead and needs replacement?
2. If yes, what are the symptoms of normal dying of battery?
3. Regarding all the posts which incline to Leopard as main cause of dying batteries should I run to buy a new one ....
4.... or it is hardware problem which lays in DC in board (heard also about battery board) which was discussed here but nobody directly gave indication that it was real cause of the problem?
5. Is it possible that even the battery will be brand new when i plug it in laptop it will die if it something related to hardware?
Thank you very much even for some smallest but helpful suggestion.
Ivan
PS: I am not in USA and not in any closest distance to Apple Store genius, most of my friends now on MB or MBP or iMac so even have nobody to try battery on exchange or even power adapter.

You didn't answer Illaass question, the newer minis have an internal power supply and should be connected directly to your mains, older ones have an external "brick". Since you mention the internal power supply, I guess your mini is one of the former, 120-240 V mains connected directly to the computer. If so, it should not be a problem using the tv power cord, if you actually have one of the older minis I don't see how you could connect the tv power cord, the contacts are really different.
So, if you have a new mini without power brick between the mains outlet and your computer, there should be no problem using any other mains cord, provided the contacts are the same. These power cords are massmanufactured by several manufacturers according to intnational standards and freely exchangeable.
Mikael

New power supply and sleep light question

I just got my iMac back with a new power supply and logic board installed under the Apple repair extension program. I had diagnosed the problem using the Apple troubleshooting assistant online. When I did this I also reset the SMU (system management unit) per the instructions with the troubleshooting assistant.
My computer is now working correctly but when I run Software Update I am prompted to install the iMac G5 Sleep Light Update version 1.0. I had previously installed version 2.0.0 back in July/05. I don't have the ambient light sensor iMac. I am a little nervous about installing this version or reinstalling the version I alreay have in my utilities. I realize this is a firmware update and cannot be reversed.
Anyone else experience this with 2 different versions of the Sleep Light Update, I don't seem to be able to find any info on the Apple site.
Thanks for any info
Scott

"reinstalling the version I alreay have in my utilities"
Please correct me if I'm wrong, but if you have it in your utilities folder, I believe that means that the installer folder has been downloaded, but the install was not done. I am thinking that once installed, it disappears from the Utilities folder.
I see no reason why you would need to do that firmware update if you don't want it. In the future, if you or someone else wants to do the update, it'll still be available on the Apple website.

Just got a new IPAD3, straight out of the box, but I cant charge it, I have tried with the power plug and cable out of the box but no joy, i have tried resetting the iPad but still no joy, have tried different plug sockets, different plugs/cables, help

Just got a new IPAD3, straight out of the box, but I cant charge it, I have tried with the power plug and cable out of the box that came with it but no joy, i have tried resetting the iPad but still no joy, have tried different mains plug sockets around the house with no joy, I have tried different USB mains plugs but again no joy, I tried using my new iPad cable into the USB port of my MacBook Pro laptop but still no joy, then, I tried using my old iPod classic cable into my MacBook Pro and that worked, so I have a way of charging my new iPad3 but its not practical as i have to take my MacBook Pro everywhere if I want to charge it which kind of defeats the object of having an iPad, has anybody experienced anything similar and how was it fixed? can anybody help me please...

Grumpy Gator,
Please note it did say at the store's discretion, but people have actually been able to return it to the on-line store. (I only saw a couple who tried.)
And given the outcry, I would think Apple might have other Apple stores join in. Just in case, though, if you can, you might bring it in today.
If it's an ARS, my guess is they can stick to their 14 day return. Apple cannot force them to do it. SO if it's not bought directly from Apple, and it's past the 14 day deal, I'd bring it in to the store today if you have one. When I gave people the cnet.com site, I gave it so people could read it and know only Apple had made the decision for Apple. And I suggested to some that an Apple reseller would probably stick with their own return policy.
Because Arnie had just bought his, he should be able to return it to Apple or an ARS because an ARS has to have some kind of full refund or at least return for credit within 7 or 14 days of purchase.
Hope this helps.

Ive tried 2 new download cards from PC world now and they both say card number is invalid

ive tried 2 new download cards from PC world now and they both say card number is invalid

You need to contact Adobe directly using the link below. Use the dropdown menu for boxes (1) & (2) to scroll down the list and choose:
1. Adobe Photoshop Elements
2. Adobe ID, and signing-in
3. Click on the blue button: Still need help? Contact us – then click the area marked chat 24/7, then click “start chat ”
It’s usually possible to start a live chat, if an Adobe agent is free, and often to get the problem fixed right away. Have your serial number available. The agent can directly troubleshoot your system if you agree to activate the Adobe Connect add-on.
Click here to get help now Contact Customer Care

Adding USB card that needs power supply H520S

Just bought a 4 port USB 3.0 card for my H520S. I plugged it in and nothing. Then I read on the card manufacturer's website that I need to the connect the card to the PSU in order for it to work (there's an internal USB port on the card).
So I opened the PC and looked for an additional power source to connect the card to...but I'm not sure what I'm supposed to be looking for.
Is this doable on this model?
If so, what cables do I need and where do I connect the cable to?
Thanks in advance

hi,
This Device Will need a 4 pin peripheral Power Cable (Molex)
Like the one to the left on this photo
Since the unit is pre configured by Lenovo all Connectors on the PSU may just be enough for all what's preinstalled inside the unit.
Still Check the power Supply of your unit check inside if there is one available This cable is directly from the power supply, so once you open the computer case Look for the power supply and check the cables coming out from it and look for this connector here is a closer look
http://upload.wikimedia.org/wikipedia/commons/3/31/Molex_female_connector.jpg
If you cannot find out you might need to Upgrade the Power Supply.
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

MDD power supply and fan upgrade kit question.

Hello, Its been a few years since I posted anything here and I'm getting ready to (possibly) trade in my mirror drive door 1GHZ dual processor machine on one of the current imac-s.
I'm not real hopeful that putting much work into my current machine is worth it. Here's why:
1) crazy levels of noise - I wear woodworking hearing protectors when I surf the web. Listening to music on itunes is fine so long as you like a background of low level blow dryer noise!
2) I'm still running OSX version 10.2.8, I have been too cheap to buy the latest OS. I'm tempted to go out and spend the $119 on 10.5 but I only have the original 256mb of ram installed and since the min requirement of ram is 512, I know I'll need to spend an extra ~50$ on a 512mb PC2700 ram chip. My price tag to do a minimal update is rising...
3) I would love to neutralize the noise and install the Apple provided MDD power supply and fan retrofit kit that they sent me at no charge several years ago while I was still under warranty. But I never did because the tech at my local (Dayton Ohio) reseller told me that the kit only addressed high noise levels when rebooting in OS9. So I never bothered. Looking on ebay, I see where power supplies for G4's could fetch 75 or 100$ or so.
In summary, here are my questions.
1) Has anything come along recently to tame MDD G4 fan noise that is easy to install, cost-effective and most of all, something that actually works to decrease the noise?
2) To get the quietest, quickest performance with the current OS 10.5 should I cut my losses now and trade (or sell on ebay) my MDD, sell the new power supply and just purchase a new machine with the OS already installed?
Thanks a bunch in advance for any assistance...
from Bill.

Bill,
Carl has some pretty good points that I'd agree with - trying the replacement PSU and fans should quiet it down somewhat and replacing the stock main fan with a newer, quieter unit will also help. But I'm going to disagree with him on running Leopard on the G4's with a few reservations.
As you might notice from my profile, I'm running Leopard on my dual-867 MDD and find the performance acceptable; perhaps a little slower than Tiger in some respects but it does run well enough within the limitations of the G4's capabilities. The reservation I have about recommending Leopard on a G4 is the graphics card - without Core Image support (which you won't have unless you upgrade the video card) Leopard is going to tax the CPU more and may bog down in some tasks like Quick Look and Cover Flow.
In the end, whether to continue upgrading the G4 is a matter of use and economics. Tiger would be a fine upgrade with minimal cost and squeeze a few more years out of your G4 if you're not requiring software that needs an Intel CPU (like certain iLife '08 apps).
-Douggo

Solution for monitor power supply and raid 5 on x4150 server

Hi everybody,
a simple question :
my compagny have some server SunFire x4150 in some Datacenter, and there is a thing that we cannot really monitored remotly : the status of the 2 power supply and the status of the raid 5 of the server.
(i want to know if a power is down or if a disk is "dead")
We are using Nagios, cacti and munin actually, so can we use these interfaces for that?
if the answer is no, a script can be developed , if only i knew the command that can be used to take informations from the state of the raid5, i'll comunicate later the type of the raid card.
what are the best solutions availables for monitor those things?
thanks by advance

We have some x4150s but they're running Linux. There are separate solutions for each of the 2 problems.
1. For the power supplies, you can use the ELOM/ILOM system management interface (also used for monitoring the fans and temperature). If you've got it configured and connected to the network, you can set it up to email you about any events. We have the older ELOM firmware running, which includes the ability to add some actions to take in response to specific events. The new and supposedly better ILOM firmware doesn't seem to include this. Since this is IPMI compatible you can probably also hook into this using ipmitool or SNMP tools.
2. For the RAID card, assuming it's the standard Adaptec (rebranded as StorageTek) controller, you can install and use StorMan software (it's on the tools & drivers CD if not pre-installed). Once again you can configure email notification from the StorMan GUI, but this time it relies on OS host services to do the mail forwarding via the host NIC.
I'm not familiar with the details of your network system admin tools, but hopefully these tips will provide pointers on what hooks are available for these tools to tie into. Presumably there's also Sun N1 management software which can probably do this in a more built-in way, but it sounds like you've already got more than enough management tools.

NX6800GT-T2D256E, Power supply and 6-pin connector

My NX6800GT-T2D256E came with a power adapter: 2x 4-pin Molex to a 6-pin connector that goes into the VGA-Card.
I've noticed that I have an identical 6-pin connector directly on my power supply (a Cieftec GPS-400AA-101A)
According to the power supply's manual, it is a PCI power connector, seemingly for powering PCI-express VGA cards.
Of course I want to use that connector, as it seems to be the ideal way of powering the card, but first I compared the pin configuration to make sure it is the same thing - and found a slight difference.
On the Adapter supplied with the card, 1 of the pins is empty (not connected) while on the connector from my power supply it is connected to +12V
Basically the pin configuration looks like this:
1 4
2 5
3 6
On the adapter supplied with the card they are:
1: +12V
2: NOT CONNECTED
3: +12V
4: Ground
5: Ground
6: Ground
On the power supply they are:
1: +12V
2: +12V
3: +12V
4: Ground
5: Ground
6: Ground
Can I safely use the connector from my power supply or could the additional +12V damage my VGA card?

Your PC has a standard ATX power supply and physical sizes will vary slightly. You might want to measure the dimensions of your power supply. Normally the standard ATX PSU will measure 5.9" by 5.5" by 3.4". You don't want to get too far away from the dimensions of your PSU since the HP mini-tower cabinets are very tight inside. I prefer the modular model PSUs to help with excess cabling issues. www.newegg.com has many good brands. Not all PSUs are created equal. Look at the warranty period, amperage on the 12+ volt bus, specification level, i7 support, efficiency rating etc..
OCZ, Enermax, Corsair and Rosewill are all good brands as is Thermaltake.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

How do I use LabVIEW to control and vary the voltage on my Agilent Power Supply and simultaneously record temp from 1 DMM and voltage from another DMM?

I am using an Agilent Power Supply to apply a voltage to a
thermistor to heat an Al chassis. I want to use LabVIEW to tell
the power supply to apply 5V for 10 minutes, then step to 7V for 10
minutes, etc. I am completely new to LabVIEW, so any help would be greatly appreciated!
In addition to that, I want to place a type J thermocouple onto the Al
surface and use a Keithley 2000 DMM to monitor the temperature (it has
a built in conversion from V to Temp for type J). I will also be
using another Kelthley 2000 DMM to record the output voltage of a new
uncalibrated thermocouple. I would like to collect the output
voltage for this uncalibrated thermocouple and the temperature reading
from the type J simultaneously. How should I go about doing this
in LabVIEW? I will be using version 6.1. The power supply
and DMMs will be connected to a PC using GPIB.
Again any suggestions would be greatly appreciated- I have no idea
where to begin on such a project. I have taught myself how to
make a basic VI- converting temp in oC to oF, but that is as far
as my knowledge goes.

What you want to do should be fairly straightward and a good way to learn labview.
First off, if you haven't already, I would download the drivers for the Keithley and Agilent instruments. I found the keithley drivers at the link below. You will need to find the labview drivers for the Agilent PS at their website. Drivers are the VI's you will use in your program to control the insturments.
http://sine.ni.com/apps/we/niid_web_display.download_page?p_id_guid=E3B19B3E90B0659CE034080020E74861
If you open Labview and go to the help menu and click on Labview bookshelf there is alot of information on getting you started coding labview. This should get you started, if you have anymore questions just ask in this same thread and I am sure you will get all the help you need.
Brian
Message Edited by BrianPack on 09-14-2005 05:21 PM
Message Edited by BrianPack on 09-14-2005 05:21 PM

Severe Incompatibility between Mac Pro 2012 power supply and Tripp Lite 2400 watt Line Conditioner [switching transformer].

Severe Incompatibility between Mac Pro 2012 power supply and Tripp Lite LC2400 [switching transformer].
The Mac Pro will not power on when connected to the Tripp Lite LC2400. The Power Supply makes continuous clicking noises and repeatedly resets the Mac Pro every 3 seconds.
The same Mac Pro connected to an outlet with no Tripp Lite starts up with no problem.

Hi,
I've the same notebook. I've not had any hardlocks so far, but I've not seen so much flash movies yet. Anyway, I just tried closing running youtube-video tab on Kde4 + enabled desktop effects -> Everything's fine.
Anyway, perhaps we can collect some issues and solutions in this thread. Here are problems, that I encounter:
- restart does not work
- errors during boot:
[ 2.399277] pnp 00:0b: [irq 23]
[ 2.399308] pnp 00:0b: Plug and Play ACPI device, IDs SMO8800 (active)
[ 2.932179] pnp 00:0c: can't evaluate _CRS: 12311
[ 14.616662] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 14.616771] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 14.616792] iTCO_wdt: cannot register miscdev on minor=130 (err=-16)
[ 14.616904] iTCO_wdt: probe of iTCO_wdt failed with error -16
[ 9.262898] sdhci-pci 0000:0b:00.1: SDHCI controller found [1217:8321] (rev 5)
[ 9.262920] sdhci-pci 0000:0b:00.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 9.262966] sdhci-pci 0000:0b:00.1: Invalid iomem size. You may experience problems.
[ 9.263176] sdhci-pci 0000:0b:00.1: setting latency timer to 64
Issued solved:
- in order to make nvidia graphics working you have to disable Optimius in BIOS.
- Battery not recognized -- fixed after recend updates
- grub2 does not work. As soon as grub2 loads, the laptop reboots. -> stick to grub1 -- works now (either I did sth wrong the first time or a new version of grub2 fixes this issue)
- in order to make the touchpad work properly install psmouse-elantech from AUR
update: this is only a half-solution. vertical scrolling on the right edge works but graphical tools which rely on x11-input-synpatics still don't work. However, everything works fine with kernel 3.3. Once this in the main arch repos you won't need psmouse-elantech anymore.
Last edited by knue (2012-03-06 23:26:26)

An ATX P4 power supply and a MSI-6119 motherboard. Does it work?

I am reparing my computer. (Power supply broke down)
I found a cheap ATX 350W P4 power supply.
It is intended for P4 motherboards, and has the same connectors as my old PSU, except one more: the ATX 12V connector (4 pin , 2 yellow 12V and 2 black earth), that you normally have to plug in a 4 PIN connector called JPW1.
On a PII/III board such as the MSI-6119, there is no JPW1.
Apparently the PSU doesn't start up if the ATX12V connector iis not plugged in.
How can I make it work?

Thanks for the manual.
No beep when booting without RAM. No sound at all. power supply does not start.
I did the following:
1. Disconnect PSU from everything - do not plug ATX connector, but short circuit pin 14 (green) and 15 (black) of the 20 pin ATX connector - put in external power cable. The PSU starts humming.
Apparently, when pin 14C is pulled low, the ATX PSU jumpstarts. ( see http://www.duxcw.com/faq/ps/ps4.htm ).
2. disconnect all drives ( HDD, CD, FDD ) (power supply and ATA66 cable) - plug 20 pin ATX connector in motherboard - connect power cable - no boot;
CONCLUSION 1: Pin 14 is not pulled low by the circuits of the motherboard, which it should. why?
3. connect all drives ( HDD, CD, FDD ) with power supply cables to PSU and ATA66 cable to motherboard.
PSU not connected to motherbord
short circuit green and 15 of the 20 pin ATX connector.
Power supply starts, HDD and CD however not ( FDD starts ).
CONCLUSION 2: connection of ATA66 cable disables power supply to HDD and CD/RW
4. connect only power supply cables to HDD/CD /FDD and not the ATA66 cables.
No connection of PSU with mothetboard
short circuit green and black of the ATX connector. ( So Motherboard not implicated )
- Power supply starts, HDD / CD and FDD start also.
CONCLUSION 3: my HDD etc and internal power cables are OK.
And I am no step further.

Power supply and multpile hard drives.

I am planning on ordering the Mac Pro, and removing the included 320 GB drive. I have four Seagate 500 GB disks that I want to install.
My main question is this: If I order the Mac Pro with only one 320 GB HD, will the computers power supply be the same as if I ordered four HDs? If I order the RAID card, is the power supply still the same?
Does anyone anticipate me having a power problem (not enough of it) to support four drives using the PS included with the single disk configuration?
Can power up delay on the disks be controlled by the Mac Pro? If so, how would I do that?
Thanks!
Message was edited by: DCIFRTHS

All Mac pros have a power supply capable of running four hard drives. Apple expects customers will add drives, so they provide the mounting sleds for the empty slots. It can handle them all starting at once.

Monitoring 3750x and 3560x Redundant Power Supply and Fans

I need help for monitoring the redundant power supply of my switches (3750x and 3560x)
I have configured my snmp on my switches and is able to monitor interfaces, temperature and etc.
The problem is when I am monitoring the redundant power supply and fans.
I am using two Cisco C3KX-PWR-350WAC Modular Power Supply per switch.
The OID I use to monitor the PSU are the following:
Power Supply 1
.1.3.6.1.4.1.9.9.13.1.5.1.3 Instance: 1003
Power Supply 2
.1.3.6.1.4.1.9.9.13.1.5.1.3 Instance: 1004
When I do an SNMP walk, the value is showing (1) which means normal.
When I simulate a power outage on power supply 1 or 2 by unplugging the power source, the value doesn't change and is still (1).
Values: normal(1), warning(2), critical(3), shutdown(4), notPresent(5)
As for the Fans:
When I remove the fan module, I am able to get a notification that the fans are down, but when I plug back the fan module it is now using a different instance.
Below is my config for SNMP:
snmp-server community XXXXXXXXXXXXXX RO
snmp-server location XXXXXX
snmp-server contact XXXXXX
snmp-server chassis-id Cisco3560X
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps transceiver all
snmp-server enable traps tty
snmp-server enable traps license
snmp-server enable traps cpu threshold
snmp-server enable traps syslog
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps port-security
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps errdisable
snmp-server enable traps vlan-membership
snmp-server host X.X.X.X version 2c XXXXXXXXXXXXXX
Note: This problem is the same for all of my 3560X switches and 3750X switches. I am not sure if I am monitoring the wrong OID.
Thanks in advance

Hi ,
You are running an old IOS code , definitely you are hitting a BUG .
there is no workaround or I would say unfirtunetely you will not be able to get the correct power supply status via SNMP.
you need to use command line for this.
I mean "show env all "
**** if you want to know the Excat BUG that your code is hitting ,please contact TAC.
Thanks-
Afroz
**Ratings Encourages Contributors ****

Macbook Pro power supply and grounding.

Hey Apple people. I noticed something disconcerting with the power supply on my MacBook Pro 13" (non-retina)
I have a stainless steel metal table in my kitchen. It is the same type of stainless steel table you find in restaurants.
I have my 13" MacBook Pro in a Speck See-thru case.
The MacBook Pro in it's case is sitting on a Rain Design "M Stand".
The Rain Design "M Stand" is sitting on the stainless steel table.
I am wearing a short sleeve shirt.
I am sitting on a fabric covered chair at the table.
The battery was getting low so I got out my power supply, which is the power brick with the two prong plug adapter.
I plugged this into a power strip and the other end into the computer.
While touching the case of the computer with one hand and leaning on the stainless steel table with my other bare arm. I felt a vibration through the fingers that were in contact with the MacBook Pro. I knew what was going on, and I got really concerned.
I tried an experiment.
I got out the extension cord that came with the MacBook Pro power supply and I changed out the two prong plug on the power supply for the extension cord. The extension cord has a grounding post.
When I plugged the power supply back into the power strip and connected the power supply to the MacBook Pro. I no longer felt a vibrating sensation when I was in contact with the stainless steel table and the computer.
I have other MacBook Pro power supplies and I always use the grounded extension cable with them, because it is located at my regular workstation area. This stainless steel table is located in my kitchen, and I was eating dinner and watching YouTube videos.
Just thought you would like to all know that when you don't use the grounded cable on your MacBook Pro. you become the ground.
Never using this power supply anywhere again without the grounded cable.
Thank you for your time.
Matthew Sievert

It depends on what you are doing. Yes, the power supply can get hot. This is normal.

No vga new viedo card,mother board,power supply and cable

Similar Messages

Maybe you are looking for