No video signal to monitor

Running WinXP Pro on MSI mainboard (6330 v.5). Just purchased a new ATI 9250 256MB AGP video card. No matter what I do, monitor (LCD) shows no signal. I've tried reseating the card dozens of times and still no go. The fan comes on but that is all. Put in my old ATI card and it works fine. I put the new card into my wifes computer (ECS mainboard) and it works great. My wife now has a new video card! Any ideas?

Quote from: Bornloser on 13-December-05, 10:14:19
The system does start, I'm sure. I'll get a long beep and then a short beep (I think) at post. That's when I know the card isn't working, along with no video message on screen. If I let it continue to run for a minute then hit the power button to shut it off, I put in my old card and then boot. I get the screen telling me that Windows didn't fully load with the option to start normally. That's because I shut the system down prematurely. I've tried everything suggested here and other forums that I visit. I guess I just have to bite the bullet and say that it is a compatibility issue and let my wife keep the new card.
Hmmm.... 9200 = PCI and 9250 = AGP ? if so i might have a solution.

Similar Messages

How do I get a video signal to an external monitor via the mini-display port on my Mac Book Air?

I can't get a video signal out through my mini-display port on my Mac Book Air (version 1). Thus I can't feed BBC iPlayer to an external monitor. There is some connectivity - the MAC wallpaper is broadcast, the mouse pointer is visible and sound is transferred. Is it likely to be a cable connection problem (though the cable works with a Windows operating laptop)?

First, what you said is contradictory. You say "can't get a video signal", then say"the Mac wallpaper is broadcast, the mouse pointer is visible". "No video signal" means an absolutely black,blank screen. It sounds like you have plenty of signal.
I am supposing what you are seeing is actually a blank desktop, which is to be expected if your settings are such that you are extending the desktop, instead of mirroring it.
Within the preference panes is a setting that allows you to change this. Open System Preferences, click Displays, and then click Arrangement. You will see that you are extending the desktop. Change that setting.

HP w2207 Monitor - "No Video Signal" After Power Outage

My mother has a Mac Mini - 2009 model - that I bought her. It is connected to an HP w2207 monitor I used to have with a mini-display port to DVI [I think, either that or VGA] adaptor. She lives 2 1/2 hours away.
Last week there was a power outage and ever since she cannot get her system to work. Her monitor says "No Video Signal" and then goes to sleep.
I worked with her for over an hour on the phone trying to fix this problem (oh what fun). Tried every combination of things I know to fix it. It seems from her description that the Mac Mini is not actually booting. When I have her turn the computer off by (press the power button, wait, press it again), she reports that she will here the disk drive spin up for 10 seconds but then no more activity. The green light is on, but that is it.
I had her reset the SCM, but that didn't work.
Any help would be greatly appreciated.
Bryan

See if the Mini will boot from the install disk. If it does, have your mom use Disk Utility to repair her internal hard drive. Repeat running repair until Disk Utility gives the disk a clean bill of health. Then repair permissions.
Disk Warrior can sometimes repair things Disk Utility can't. However, it's possible the internal directory is beyond help. In that case, erasing the internal disk and reinstalling the system will be necessary. It's also possible that the disk itself or electronic components in the Mini have been damaged which would require repair at the Mac hospital.
You might want to consider buying your mom a UPC.

Monitor no longer recieves video signal [Solved... w/ Fire.]

Greetings and thanks in advance for reading. I'm thinking the problem is either Video or Processor but second opinions are always appreciated:
The problem started about a week ago when I was playing Wizardry 8 via Cedega (OpenGL accelerated Game.) The screen mysteriously went black, the monitor turned to low power mode and the sound looped once or twice before just going dead altogether -- yet the computer was still on. I rebooted and things worked again.
2 days ago the game thing happend while playing Unreal Tournament 2004. Montior went black, sound looped once or twice from the past few seconds, then power stayed on but there was no video signal. I tried rebooting this time only to find nothing happening and it's still doing nothing since. The power turns on, no beeps or anything occur and it goes thru the same familiar clicks when checking the hard drives and CD Rom. (The spinning still occurs as well, the keyboard blinks once and I can turn on / off the numlock. The fans turn on inside the case, and the network adapter is recieving a current.)
I tried taking out the RAM, unplugging the hard drives and such systematicallyh only to have it do the same thing. It boots up, doesn't beep, doesn't proceed and the monitor remains blank. I tried swapping the monitors with no avail. I even cleared the BIOS via popping the battery and waiting a bit (yes it was unplugged) The only thing that produced a notable difference was when I unplugged the video card and powered it up without one. It beeped once long, waited, beeped again long, waited, and kept doing this ad infinitum. I should also mention the red LED indicating that the HD is being accessed is constantly on but there is no HD activity discinerable to the human ear.
My hard ware is a Gigabyte 64 Bit AMD Board (Tryton K8 I believe), GF6 6600 GT, PCIE Model 1 gig of RAM and the rest are minute details but I'll include them upon request.
I've had this machine little under a year now (actually 2 weeks from now it'l be ja year) I haven't swapped out the video or processor since I do not have a spare one to replace it with to test it, neither do any of my friends.
Any further questions or such, let me know. Thanks in advance again.
(Meant PCIE, not EIDE, sorry for the confusion)

Something similar happened to a friend of mine. His laptop (under windows) bsoded twice while playing cube. the second time, it didnt boot up again, and refused to power on, there was no sound from the hard drive, the laptop didnt boot at all.
It turned out he had busted up ram... *shrug* it's hard to say though, such symptoms could highlight a lot of things.
Make sure all the connectors in your case are fine, everything's plugged in, and if you can, test out the ram in another compy
James

Firmware 2.0 Video Signal Monitor Issues

This is a story of woe regarding my issues with the histogram "video signal monitor"Everything described below is using CineEI Since purchasing the camera, I was never able to get the VSM to display consistently. There seemed to be little rhyme or reason to when it displayed and when it didn't. As with any other issue, I put my faith in the second coming, firmware 2.0. Today, I excitedly downloaded and installed 2.0. So far, only disappointment. Initially, I was able to get the VSM to display in every 23.98 recording format (I didn't try other framerates)I even tried turning on all the outputs, and was happy to find that my VSM stuck around. - Everything that follows is XAVC-L 1080 @ 23.98 - Then I tried turning on a LUT and everything went to ****** in a hand-basket. After turning on a Viewfinder LUT, I ony got that lovely "cannot proceed" message every time I tried to enable the VSM. I tried turing off all the outputs, turning off output displays, nothing helped. Frustrating, needless to say. But, because the VSM would be sampling the post-LUT image anyway, I wasn't heartbroken...yet. Defeated, I turned OFF the viewfinder LUT. Got excited to see my new friend the VSM. But now, even with the LUT off, I get the "cannot proceed" message. I've switched every related setting in the camera, outputs, output display, output formats, other LUT settings. Nothing helps. Now I can't do anything to get the VSM to display on my camera. I've tweeked every setting imaginable. I've tried restarting multiple times, even switching between Cine EI and custom. the VSM won't even display in custom mode now... The only fix I've found is to do an All Rest. Doing so allows the VSM to display without a LUT. But, once I turn on a LUT, the VSM disappears for good, even after I switch the LUT back off. I wouldn't wih this frustration on my enemies but has anyone else experienced this after upgrading to 2.0? Sony, is there a matrix somewhere that can educate us on when the VSM can and cannot be displayed? It's hard to discern when I'm experiencing nominal behaviour without knowing what to expect from normal operation.

ok, I found an output combination that I must have missed earlier which narrows my issue. My VSM won't display unless an SDI output is enabled. HDMI output setting makes no difference. So, after enabling SDI in "Output On/Off": SDI 2048x1080Psf HDMI --- VSM: YESSDI 1920x1080Psf HDMI --- VSM: YESSDI --- HDMI 1920x1080P VSM: NOSDI 1920x1080i (2-3pd) HDMI 1920x1080i (2-3pd) VSM: YES The same concept holds true for UHD and QHD. Without an SDI output enabled, no VSM. Erik, I suspect that if you enable an SDI output, you'll be able to display the VSM in all recording formats.

When i on the pc message i get in monitor no video signal please tell me the solution

Pls help me to solve my desktop when I do on the pc I get message in monitor no video input and nothing is appearing in the screen of the montior only message i got it But i think that pc is working(fan is on).
Thank you Best regards
PriyankaJeeva

Hello PriyankaJeeva,
When turning on your computer you receive a message stating “no video signal”, is that correct? I will be happy to help you.
Can you please provide the full model of the computer you have, If you are unsure where to locate that information have a look at this link for help if needed.
Also what model monitor do you have, it should be located on the bottom right or left corner of the monitor if its an HP monitor.
Please respond back at your earliest convenience.
Thanks
Clicking the White Kudos star on the left is a way to say Thanks!
Clicking the 'Accept as Solution' button is a way to let others know which steps helped solve the problem!

K9N Platinum, 7600GTOC, SLI, No Video Signal

Just built up my new system, specs as follows
MSI K9N Platinum
AMD 5200X2 AM2 CPU
2 Gigs Corsair XMS2 DDR800
2 BFG Tech 7600GT OC's in SLI
Thermaltake TR2-500 Watt PSU +12V(1) 14A +12V(2)15A
1 Maxtor 120 GB SATA 150
1 Maxtor 160 GB SATA 160
When i turned the computer on for the first time, the system boots up and there is one small beep, sounds like it is posting, but I get no video signal from my monitor, which I checked on my other computer and is working fine, I tried both video cards in the 1st slot, in non-sli mode and I get the same result each time, so I get no video signal with all ways tried? Do I not have enough power in this PSU to run what I have? The video manufacturer suggests a 450W PSU, which I meet, but do I not have enough juice the 12V rails? And would this cause the no signal? Any help would be much appreciated.

Hello, welcome to forum.
"When i turned the computer on for the first time, the system boots up and there is one small beep, sounds like it is posting, but I get no video signal from my monitor, which I checked on my other computer and is working fine, I tried both video cards in the 1st slot, in non-sli mode and I get the same result each time, so I get no video signal with all ways tried?"
have you tried with one of them only into 1st PCI-E? use 1st DVI output, when using SLI, ensure SLI bridge is configured property, connect monitor to VGA onto 1st PCI-E slot. also check monitor output is configured property(etc: Input 1, Input 2).
power down PC, remove power cord from the PSU and Clear CMOS Guide
re-test.
ensure all power cables are connected property. try to boot with one memory stick only into slot close to CPU socket.
what D-bracket shows?
"Do I not have enough power in this PSU to run what I have? The video manufacturer suggests a 450W PSU, which I meet, but do I not have enough juice the 12V rails? And would this cause the no signal?"
yes, think is too weak for your system
its recommended to get single rail with high amperes on +12V (over 30A)
read here:
PSU's---2 x 12v---The Dual Rail Myth
Is your problem caused by your PSU?
good suggestion can be found here:
https://forum-en.msi.com/index.php?topic=105635.msg783148#msg783148
https://forum-en.msi.com/index.php?topic=103299.msg757739#msg757739

Solutions for displaying s-video signal on Macbook Pro? (2006 model)

I looking around for ways to display an s-video signal on my Macbook Pro, but i've no idea the best way to this.
I'm not really after capturing or recording the signal, but I just need a means that I can view the signal, and to be able to switch to another program running on the Macbook. (switch back and forth from Mac app to viewing s-video signal)
Ive seen a few products but they look overblown for what I really need to do like the Elgato video capture, and the xlr8 provideo usb devices.
Is there a way that I could use the DVI socket on the Macbook? I have seem its possible to display the Macbook signal on an external display using this socket, but can it be used to take an input signal?
Message was edited by: jauqq
Technical note of what I exactly need this for: I have an old Roland sampler which can be used with an external monitor to aid in its editing. The outputs on the sampler are s-video and digital RGB. So that I dont have to buy an old bulky monitor I want to use my Macbook display for this while I also am running Logic Pro 8 at the same time. And to switch from Logic, to the displayed signal from the sampler.

The DVI out on your MacBookPro cannot be used for input. In order to see the s-video signal on your MBP display you will need an analog-digital converter like the Canopus ADVC-55, plus you will need to run software. You may be able to use iChat A/V, although I haven't tried it for this purpose. It will cost you more than the Elgato eyeTV device, however.
You will find it much easier & cheaper if you just get an inexpensive LCD display to use with your Roland sampler.

Video signaling problem caused by 1.9, 2.0 BIOS (pointing out a BIOS problem)

Hi, i have a problem with the video signal. At random times when i boot up my computer, the computer would power up but there is no signal to the monitor. there is no hdd activity (via the hdd led) and nothing seems to be happening just that the fans are whirring. i have to unplug the computer then plug it again then turn it up again which sometimes repeats the problem. This is very irritating! So i did a little bit of troubleshooting:
1. I changed video cards. I used a SAPPHIRE ati radeon 9600XT fireblade and a LEADTEK GF4 ti4200. Both cards were causing the same problem and when i used both cards to another computer, there is no problem. = NOT A video card problem
2. used differnt kinds of drivers Cat 3.10, 4.10, 4.20 (omega and official) does not seem to do anything (which also i believe the drivers are OS dependent and its the bios of the vid card that starts up the vid card)
3. upgraded from 1.9 to 2.0 BIOS. still the same problem
4. reverted from 2.0 to 1.7 BIOS. the problem ended.
BTW, the board is 865PE-Neo2 - S. on a Intel 2.6Ghz C, 512MB TwinMos ram with m-tec chips, 80gb hdd, enermax 300w psu
so ive' solved the problem, and i just wanted to point out that there is a problem with 1.9, 2.0 BIOS. (havnt tried the 1.8 tho)

Wish I had seen this thread 2 weeks ago, but you did save me from buying a new graphics card. That was the last step (before chucking this mobo completely) in my attempts to fix the same problem. It didn't bother me too much, except I also couldn't get any DVD player (tried 3) to work. Would boot sometimes and at others gave a blue screen video error.
Flashing to bios 1.7 was the only thing that fixed it. Tried different memory, updating software, various combinations of drives, etc. For the record I tried bios 1.8, 1.9, 2.0, and 2.1. Not sure what about those updates causes problems but there definitely is something wrong.
Thanks.

No video signal? help please

Just built new system. MSI neo 2 ls, 2.8 p4, 1g ddr400, ati 9700 pro vid card, using on board sound for now. Everything was working great for about 8 hours. Was playing ut 2003 and system froze. Then on reboot got "monitor working- no output signal". Have tried all I can think of including switching video cards and monitor but no luck. Did the board fail?

Thanks for the effort. The d-bracket leds are showing the top 2(initializing hdd controller). It gets thier very quickly on boot and stays there. What do ya think?

No video signal in

I am using FCP 4.5 HD, I have a G5, tiger, using a DSR-80 going into the AJA lo la using component, I am firewire into the mac. I get video on my NTSC monitor through the aja but no video into FCP, my device control is aja lo la rs-422, capture input aja lo al composite 10 bit. I get nothing in the preview and when I go to capture now. it tells me "no video signal" any ideas what I am doing wrong?

am using FCP 4.5 HD, I have a G5, tiger, using a DSR-80 going into the AJA lo la using component, I am firewire into the mac. I get video on my NTSC monitor through the aja but no video into FCP
So what is it Charisa, Final Cut PRO or EXPRESS?
http://discussions.apple.com/thread.jspa?messageID=7308988&tstart=0#7308988
If you are using PRO then what else do you have plugged into your Firewire bus? AJA's external boxes do not play well with others on the same bus. They have to have one all to their self.
Also, do you have the latest AJA drivers?
K

46SL412U Sudden No Video Signal for all HDMI Ports

My daughters and I were playing the Wii U tonight on our Toshiba 46SL412U LED TV when suddenly the picture when black and the No Video Signal message came up. I changed out the HDMI cable thinking the cable went bad, but still no picture. I power cycled the TV, still nothing. I am also not getting any picture with any of my other devices that are hooked up via HDMI port (BluRay player, Chromecast). Oddly, the REGZA-LINK still recognized that the BluRay and Chromecast are plugged in and switches to the correct input when I power either of them on, but i'm still getting the No Video Signal message.
Is there a setting I've missed that suddenly changed, or did all of my HDMI inputs suddenly go bad? What can I do to fix this issue?

To check the Graphics card's funtionality you may go to BIOS menu and see if is it listed or not; if yes, then it's working, and you may have to check the video/HDMI cables.
Try to boot the PC without connecting any device other than monitor, power cable, mouse and keyboard.
To check the warranty, you may use the below link:
http://www11.itrc.hp.com/service/ewarranty/warrantyInput.do?admit=109447626+1275645640303+28353475
If you have any doubt regarding the warranty, contact HP support.

Unsupported Video Signal

Have a 47TL515 3D tv. Plugged in a VHS player and it shows the picture fine, but there is an error message on the bottom in a big grey box that reads "Unsupported Video Signal". How do I get rid of the box? It won't go away.

So is this forum to post our issues with new Toshiba products? Do Toshiba support employees even monitor or use this site? Or is it just a place for digruntled users to cry on each others shoulders?
I may have found a temporary fix to my problem. Was trying to watch another VHS tape with this annoying "Unsupported Video Signal" box on the screen and decided I couldn't take it anymore. I switched the RCA adapter I had plugged into Video 2 with the adapter plugged into Video 1. Switched input so now I was viewing VHS playback on Video 1. Same problem. Big gray Unsupported Video Signal box still there. So I switched them back, so VHS is now plugged into RCA plug adapter in Video 2 slot. All of a sudden the big gray box is gone! And it stayed that way! Was able to enjoy a whole movie without it coming back. And now, a day later, after shutting everything down last night and turning it back on tonight, the big gray box is still missing. Yay!
Thanks for nothing Toshiba.

Sending video signal to television

Is there a wireless solution to send a video signal from my mac pro to a tv monitor?

http://www.apple.com/appletv/

Keynote video signal drops out

Keynote 4 video signal drops out during presentations where we are switching between two different Apple Computers (one G4 and one Intel). Both machines had previous versions of Keynote on them and over a period of time never had a signal drop out condition. Sounds like new version problem.
Any input appreciated.

I have two laptops each with their video out adapter connected and then cabled to a switch box where the big monitors project the signal of the laptop that the swtich box is set to. Like channel selection. Previous versions of Keynote were never a problem and I mean never. The signal came right through but now with Keynote 4 the signal drops out even tho the laptop is still active and apparently sending a signal through its video out connection. I have to hit escape and get out of keynote and then go back to PLAY for keynote to once again send that signal.

No video signal to monitor

Similar Messages

Maybe you are looking for