No webcam, and Settings greyed out

Hi all,
When opening my movie in Flash Player (latest version) the webcam doesnt work. I dont see the dialog at the start (the 'Do you allow to use...' dialog) at all. Also, the settings accessed from the right click menu is permanently greyed out. However, when opening the same SWF in Flash itself, it works fine in both respects.
Other movies have Settings enabled just fine in Player, too.
Any ideas what might be going on? I can't see anything that matches anywhere on the web. Thanks very much in advance!
Gerred

Take each of the following steps that you haven't already tried.
1. If anything is plugged into the audio-out (headphone) port, unplug it.
2. Select  ▹ System Preferences ▹ Sound ▹ Output. Check the settings. The internal speakers should be selected as the output device, the Mute box should not be checked, and the volume slider should be at least halfway to the right.
3. You may need to darken the room for this step. Look inside the headphone port. If a red light is coming from the port, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a headphone mini-stereo jack of the proper size. Inserting any kind of tool in the port may cause damage that won't be covered by your warranty.
4. Boot in safe mode by holding down the shift, or if the boot volume is a software RAID key at the startup chime. It will take much longer than usual. You don't have to log in; just reboot as usual (without holding any keys) when the login screen appears. (Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode.)
5. Reset the PRAM and NVRAM.
6. Reset the SMC.
7. Make a "Genius" appointment at an Apple Store.
Back up all data on the internal drive(s) before you hand over your computer to anyone. If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to bare metal from any of them.) Don’t erase the recovery partition, if present.
*An SSD doesn't need to be zeroed.

Similar Messages

After upgrading to IOS 5.1.1 the Wi-Fi selection in settings greyed out and now says No Wi-Fi. Have tried restting and restoring both from te phone and from Itunes but this does not solve the problem.

I recently upgraded my Iphone 4s to 5.1.1 and founf the Wi-Fi button in settings greyed out saying No Wi-Fi. I have tried Reset network Settings, Rest All Settings and restore in Itunes but to no avail. I understand this is a comon occurence but I cant find a solution to it. Can anybody help?

See this tip --> http://support.apple.com/kb/TS1559
If this doesn't resolve it you most likely have a hardware failure. Fortunately, your phone is in warranty, so if you take it to an Apple store they will replace it.

I updated my iPhone and now none of the music on it will play. When I sync, I can change teh music selections on it, but they all won't play and are greyed out. Only the Playlists, Artists, Albums are black font, but all songs are grey and won't play

I recently updated my iPhone 3G to 5.0 (9A334) and it was somehow interrupted during restoration, or at least that is what it tells me. But it keeps making a new restore and adding it to a list, but never gets through without getting interrupted. anyways, I kind of got through all that, but now all the music on the iPhone won't play and is greyed out. I had some APPs greyed out, but they are not as important. Music is a huge investment in my life and this part of it has gone silent. I SYNC with my iMac. Resyncing doesn't help. I can change the selections, but can never get them to play on the iPhone.
Any ideas?

I'm having the same issue, i restored my phone to Factory settings, even tried restoring it to my backup, half of my music bought from itunes won't play on my iphone and i'm super annoyed, this only happened once i updated to ios 7.2 so i assume its another glitch to go with my imessages not sending, getting sick of this.

Linux Flashplayer10 settings greyed out

Hello,
since the update to Version 10 (I think) I can not access the settings when I right click on a flash. The settings greyed out. What can I do to access the settings again?
My system: Ubuntu Hardy with FF 3.0.15 and FlashPlayer 10,0,32,18
Thanks for help.

Hi, You can use this test site and it will also display what version of Flash Player Installed. The version you listed is very old.
http://www.adobe.com/software/flash/about/
If Flash Player is Installed correctly you should also see the Flash logo aninmate(spin).
eidnolb

After upgrading to ios8 my 4s text dictation microphone does not work and is "greyed" out

After upgrading to ios8 my 4s text dictation microphone does not work and is "greyed" out. There is no function at all.

Ok I fixed the issue, turns out a couple of weeks ago, I downloaded a program that was suppose to help shrink some of your stuff to use less data, it was called Onavo. It was suppose to show you how much data you use to help keep you within your limits. If you have downloaded this, go through your settings and delete it and it will fix the problem. At least it did for me. I can now send photo's to non Iphone users via text no problem.

My internal hard drive wont show on the desktop and is greyed out in the finder

My Internal drive will not show up on the desktop, and appears greyed out in the finder.
it shows up fine in disk utility and i have tried to repair permissions. This runs normally, there does not seem to be any problems with the drive itself.
if i unhide the hidden system folders using terminal, it appears on my desktop again, but greyed out.
any ideas how i can fix this?

Try deleting the Finder .plists. You need to look in your user Library/Preferences for the .plist. Hold down the option key while using the Finder “Go To Folder” command. Enter ~/Library/Preferences. Move the .plist(s) to your desktop.
Relaunch Finder and test. If it works okay, delete the plist(s) from the desktop.
If the Finder is the same, return the .plist(s) to where you got them from, overwriting the newer ones.
If you prefer to make your user library permanently visible, use the Terminal command found below.
http://osxdaily.com/2011/07/04/show-library-directory-in-mac-os-x-lion/
You might want to bookmark the command. I had to use it again after I installed 10.8.2. I have also been informed that if you drag the user library to Finder it will remain visible.
If that doesn't work, try setting up another admin user account to see if the same problem continues. If Back-to-My Mac is selected in System Preferences, the Guest account will not work. The intent is to see if it is specific to one account or a system wide problem. This account can be deleted later.
Isolating an issue by using another user account
If the problem is still there, try booting into the Safe Mode. Shut down the computer and then power it back up. Immediately after hearing the startup chime, hold down the shift key and continue to hold it until the gray Apple icon and a progress bar appear. The boot up is significantly slower than normal. This will reset some caches, forces a directory check, and disables all startup and login items, among other things. If the system operates normally, there may be 3rd party applications which are causing a problem. Try deleting/disabling the third party applications after a restart by using the application unistaller. For each disable/delete, you will need to restart if you don't do them all at once.
Safe Mode
Safe Mode - About
General information.
Isolating issues in Mac OS X
Troubleshooting Permission Issues
Step by Step to Fix Your Mac

Sometimes, when I click on a link, I see in the address bar the words: "Search bookmarks and history" (greyed out) just before I am taken to the link. Should I be worried? Is someone searching my personal data? Is this just a FireFox error msg?

Sometimes, when I click a link on a web page, I see in the address bar the words: "Search bookmarks and history" (greyed out) just before I am taken to the link I clicked. A moment later, when I'm at the link, its address appears in the address bar, and all is normal. It seems that this happens only from some particular sites. Is FireFox reporting that my bookmarks and history are being searched?
Should I be worried? Is someone searching my personal data? Is this just a FireFox error msg when it has trouble finding the website I requested?

That is OK. Firefox will only display the link in the location bar after the DNS look up has succeeded and a connection to the server has been established. Until that has been done you see the default setting for the location bar: Tools > Options > Privacy > Location Bar: When using the location bar, suggest

I cannot access Content Library in iMovie - Content Library doesn't show on the iMovie screen and is greyed out when accessed through "windows" tab at the top. Also unable to update the projects/events (a suggested solution for a similar question).

I cannot access Content Library in iMovie - Content Library doesn't show on the iMovie screen and is greyed out when accessed through "windows" tab at the top. Also unable to update the projects/events (a suggested solution for a similar question). I haven't had this issue before, I have always used the content library on the screen but haven't used this for about a month. How can I make the Content Library available?

Thanks so much! I am backing up the entire computer now with an external hard drive - this should be fine right? And surely if I am backing up the whole computer these projects/videos will be backed up too? I wasn't sure how to do this any other way and I am clearly not great with tech issues. Once this is done and I am sure my projects/videos are safe I will do the delete and reinstall bit. Thanks for taking the time to help

My ipad2 safari is not responding and has greyed out

safari on my ipad2 is not responding and has greyed out... is there a way i can sort it out ?

If you follow Bob's instructions.. allow it to cool down.. maybe leave it off overnight.. if the disk fails to start when you power on.. or listen carefully and hear if the disk is failing to spin up properly then you have either dead drive or dead supply.
Is it in warranty or applecare, let apple replace it?
If it is out of applecare even, open it and replace the disk.
How old is the TC? What model from the rubber mat A1xxx? What size disk?
Certain drives are becoming unreliable.. The WD black in Gen2, The Samsung Spinpoint in Gen3 and WD green in Gen3 and Gen4 are none of them great drives.
Out of warranty do the job yourself.. there is plenty of stuff about drive upgrades for the TC.
Excellent instructions here.
http://www.ifixit.com/Device/Apple_Time_Capsule

Imessage on Mac has my wifes phone number and its greyed out and i cant change it to my number (on the beta version of iMessage for the mac)

hey-- so iMessage on ONE computer has my wifes phone number in under iMessage and its greyed out and i cant change it to my number. any ideas? ive done what people have suggested on these forums, e.g., check your apple id make sure your number is associated with it etc. how do i change the iMessage number from my wifes to my actual number? thanks! R

HI,
This can depend on the the Apple ID that is used.
I was under the impression that the invididual parts of an iCloud ID could be "registered" separately for iMessages but this may not be correct.
I have an Apple ID that is based on a email from a source external to Apple. (an old Dial-up account email)
I registered this for iCloud and at the time got an @me.com name as well.
I also have two iPhones so I decided to use the @me.com name on one iPhone and the older Dial-up on the other.
This seemed to work up to the OS X10.8.2 and iOS 6 updates.
AT this points I did the OS X one first then the iPhones
I got alerts in Messages on the Mac to add the Dial-up ID iPhone's number to Messages which I accepted.
The Messages Menu > Accounts > iMessages showed the iPhone Number as an alternative Receive ID and offered itself in the Drop as the Send from ID.
I then set up the second iPhone and got an alert in Messages to add the Apple ID and the iPhone number to Messages.
I said no to this.
At iOS 6 this did not get added to the Messages > Preferences > Accounts > iMessage panel.
However at iOS 6.0.2 the iPhones are showing their own Numbers as Greyed out and even though I refused again the @me.com ID and second iPhone's Number they have been added to the Message Menu > Preferences > Accounts > iMessages pane although they are not ticked.
The only link these two Apple ID Names have is that they are both associated with the iCloud Account.
(I Can log in to the same iTunes account with either name, and post here, and access iCloud in a web browser - the password is the same).
I have successfully managed to get one iPhone to have it's greyed out Number ticked so it can accept iMessages sent to the Number.
This involved removing the Apple ID on that iPhone, Closing iMessages, restarting iMessages and then re-adding the Apple ID
I did get an alert to say the ID would not work anywhere in iMessages when removing it.
It was 24 hours before I got an alert in Messages again to add the iPhone Number and Apple ID (I said no and they are not active but do show in the iMessage account on the Mac)
I am a little confused by this bit:-
...ONE computer has my wife's phone number in under iMessage and its greyed out ...
I can see the iPhone Numbers in Messages Menu > Preferences > Accounts >iMessages Account pane but they are not greyed out even when not active
They are only greyed out on the iPhone's themselves.
I would also make sure the Apple IDs used on each computer and it's related iPhone are separate from each other.
9:52 PM Tuesday; November 27, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.2)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Color and Color Management boxes in Print Settings greyed out. Using PS CS5.1 with Mac OSX 10.9.5.

For some reason, the above boxes are now greyed out when I go to Print Settings and I am getting prints that are badly distorted. Was working perfectly a few days ago and can't understand why this has suddenly happened ? Am now confused as to what settings I should have in the Color Management dialogue box in order to get back to the correct operation.

I've also been having this problem. My computer now consistently shuts down between 10 seconds and 2 minutes of startup. This only happens if my computer is not plugged in. (my battery has been between 70-90% the entire time.) If I keep it plugged in...no problems.
13-inch, Mid 2013 MacBook Air
1.3 Ghz Intel Core i5, 8 GB 1600 Mhz DDr3).

Redirected Printer Settings Greyed out and Missing Finisher & Trays

Hi,
I have added a new local printer . The printer has 2 additional trays and a finisher added.
When I log onto the terminal server (server 2008 R2), the printer is redirected, but without the extra 2 trays and finisher. Most options are greyed out within the properties of the printer driver.
Same as this issue here:
http://social.technet.microsoft.com/Forums/windowsserver/en-US/2eeeb270-9cbb-4628-ad22-0ef3df6549d6/printers-not-redirecting-properties-and-preferences
The driver is installed on the server and I have tried disabling the 2 GPO settings 'Use Terminal Services Easy Print printer driver first' and 'Use Remote Desktop Easy Print printer driver first'.
Does anyone know a solution to this??

Done a bit more digging and this is done 'by design' by Microsoft (I guess it's a limitation of their printing model, shame they haven't addressed this as the problem goes back to Server 2003 and still unresolved!).
This KB explains the problem: http://support.microsoft.com/default.aspx?scid=KB;EN-US;243942
I can now change the device settings for the redirected printer driver (as per KB article above), but after logging off the terminal server and logging back on, the redirected printer reverts back to the default settings.
This is a massive problem for my customer as they are unable to use most of the features on their new copier (they work within a terminal server environment).
Anyone else had this problem and been able to save changes to the redirected printer settings??
Thanks in advance.

My macbook pro's sound is not working properly. It flashes from normal to grey in the menu bar up top, and when greyed out I cannot do anything with it, and it sits at max.

In system preferences > sound > output, it will switch from normal internal speakers > built-in, to headphones > built-in, to digital out > built-in, to headphones > headphone port, to digital out > headphone port- it's nuts! This is all without having anything actually plugged into the headphone jack. While it is greyed out (which happens randomly and on any of the settings), there is no sound whatsoever and it says, "The selected device has no output controls.". Also coinciding with this, my computer has begun to suddenly run extremely slow and lags a lot. Is there a way to fix this? I already tried updating my computer, and restarting it, and it didn't help. I'm wondering if maybe the headphone jack somehow was shorted while I had some speakers plugged in for gaming...? Or is this something I need to send my computer in to be repaired for?
It was custom-ordered a few years ago, and unfortunately the warranty has expired. :/ Perfect timing.

I have this same issue and have been struggling with it for a while. I really just need to get it into Apple Store to be fixed most likely - but avoiding the hassle and time needed to do so.
Things I've come across:
Something inside of the headphone jack is not right, such that it randomly thinks headphones or some other type of optical audio device are plugged in. you will see a red light inside the jack occasionally when it happens.
You might try doing PRAM and/or SMC reset ( http://support.apple.com/kb/HT3964 )

IPad wifi and Bluetooth greyed out after iOS5 update

After updating to iOS5 on my iPad my WiFi and Bluetooth were greyed out like the update has caused a hardware failure on the radio side. My SIM and 3G still work (not that I use it) but I can not even choose wifi or bluetooth in settings app as they are greyed out.
In Wifi it says "No Wi-Fi" and Bluetooth it says "Unavailable"
I wasn't using it a lot so just forgot about it for a while as it sat gathering dust being an expensive paperweight thinking that the next software (5.0.1) update would sort it all out. It doesn't. I have a 64GB iPad 3G with no wifi and as I am living abroad the 3G is useless to me (though only use the ipad at home on my wirless network anyway, or not as the case is now!!)
I have restored, factory restored, cleaned installed new software, everything I can think of but still there is no wifi and no bluetooth.
Has anyone else had this issue? My (very expensive) iPad is now next to useless!!
ANY help is VERY much appreciated.

thank you for fast response and sharing the link but i've tried everything including downgrade but it seems that theres a serious problem with MC497LL model and trying to reach to the support for any updates about it at least trying to inform them

IOS 7 and the 'greyed out' WiFi problem

Hi,
Looking for any solutions to this:
I upgraded to iOS 7 with no problems initially
After about 24-36 hrs I noticed I could no longer access websites via the WiFi connection, so I restarted the phone (a 4S on the Bell Canada network).
Since then, the WiFi slider has been greyed out and I can't access WiFi networks - with the exception of about an hour or two coincidentally around the time of the 7.0.2 release.
The WiFi button on the control centre appears to work, but of course doesn't actually function as designed.
So far I've tried the following:
Power on & off
Reset the phone (home & power buttons until Apple logo shows)
Reset network settings
Various versions of having the phone in or not-in airplane mode while doing the above
Renaming the phone without appostrophies.
Reinstalling iTunes & re sync
Upgrading to 7.0.2
Completely wiping the phone and reinstalling everything from iTunes (painful, I know)
Going into the store that sold me the phone (I won't say here, but they weren't very nice about Apple)
None of the above have worked.
Some reading suggests it could be the phone's chipset, but I'd argue that as it's connected to WiFi just fine a couple if times.
The only idea I've read and not yet got round to trying involves freezing the handset.
Anyone else with any other ideas?
Thanks!

Tony,
I've been reading up on this 4S wifi greyed out topic for the past several days too. I have a 5 and I don't have the wifi greyed out problem (knock on wood).
There's been quite a huge volume of discussion on this issue, with some people suggesting that there is a hardware defect, while others finding it just too coincidental that so many people would have this same problem on the same occassion, ie upgrade to iOS7 or 7.0.1 or 7.0.2.
The strangest thing about this: there's a user, carolinelewis, who is on her second new replacement 4S from Apple but they still show wifi greyed out after a while!
https://discussions.apple.com/thread/4638071?start=300&tstart=0
(page 21 of the thread).
Some people swear by the freezer method, some say the hot dryer method worked for them. Some say using either methods would get it fixed, some say the problem returns after some days.
My thoughts is that both freezer and hot dryer methods are actually taking the phone out of its operational temperature range.
Environmental requirements of 4S:
Operating temperature: 32° to 95° F (0° to 35° C)
Nonoperating temperature: -4° to 113° F (-20° to 45° C)
Relative humidity: 5% to 95% noncondensing
This action may have cause the 4S to do a complete initialization when returned to normal temperature, but these 2 methods appear to be last ditch efforts.
What I'd favor is power cycling the 4S, which can be achieved by running it completely out of battery, as shown in this Youtube video: http://youtu.be/o_ws5srnVVM
then plug in power and just may work for you.
I've also come across this person's workaround: http://www.youtube.com/watch?v=vzb5LNB9nIA
which may work for the 4S on iOS7 (it was posted for iOS6).
The steps this gentleman proposed appears to be worth a try. His strategy is to put the iphone into airplane mode, then do a hard reset.
Now, I have had my Thinkpad (Windows7) laptop's wifi freeze up akin to the behavior of 4S on iOS, ie can't turn on wifi radio via software, just simply refuses to see SSID of wifi router, won't join, etc. I've always been able to get things back to normal by power cycling the laptop. In some freak instances, even shutdown won't work, I would pull the battery out of the laptop to get eveything back to normal.
So my thoughts on this 4S wifi button grey out is that there is something in the iOS7 upgrade process that caused the wifi circuitry to freeze up and need a complete restart from powered down state.
The fact that the iphone doesn't have an easily removed battery makes it harder, and I suspect the freezer and dryer technics are an indirect way of acheiving total power off (battery not supplying power due to extreme high or low temperatures).
Furthermore, I've read that some people fixed their wifi greyed out problem by deleting older apps that may not be fully compatible with iOS7 and thus locking it up. Well, if that were true, then it may explain why the problem returns for some people. We won't know who upgraded which app.
And of course, there are instances where the wifi hardware that happen to be in a marginal state. Kind of like a PC working fine, installing updates, then stalling on reboot because the boot sector failed or some driver got stuck during initialization stage. This may explain why for some people the 4S had been working just fine but got broken wifi after the upgrade.
Best of luck to you in your efforts to get this problem fixed.

No webcam, and Settings greyed out

Similar Messages

Maybe you are looking for