Nokia 500 unable to connect to Netgear WGR614

I have installed the Router "Netgear WGR614" and i connected it to 3 systems and one of them is a Wireless Laptop, when i am able to browsing through laptop then why i am unable to browse through my Nokia 500 Phone?
I have also given the Password but it is keep on saying "Connection failed" why?
just not when i was at office i was able to connect to another Netgear router, but that router doesnt have a security password.
thank you.
Reddy.
Solved!
Go to Solution.

Hey bgautham,
Welcome to the discussion board!
As you are able to connect with your device when you are at the office it looks more like a router issue. 
Have you tried creating a new access point as shown is this video, also make sure that you are inputting the right characters, respecting lower and upper cases.
You can try resetting your router as some may need a reset to accept a new device connection.
Hope this helps! 
BaptisteJu

Similar Messages

  • HTTP Response :500 unable to connect to remote system.

    Hi,
    I am doing proxy-xi-file scenario, where i am getting this error in sxmb_moni in R/3.
    The error reads with red flag:
    HTTP Response :500 unable to connect to remote system.
    Please  tell me what can be the reason.

    Snehal,
    Error: The error message 503 Service unavailable Application stopped! is displayed.
    Description: The server is currently unable to handle the request due to a temporary overloading or maintenance of the server. The implication is that this is a temporary condition which will be alleviated after some delay. If known, the length of the delay MAY be indicated in a Retry-After header. If no Retry-After is given, the client SHOULD handle the response as it would for a 500 response.
    Note: The existence of the 503 status code does not imply that a server must use it when becoming overloaded. Some servers may wish to simply refuse the connection.
    Possible Tips: Because of J2EE application com.sap.aii.af.ms.app not active
    • Try to (re)start the application using the Visual Administrator Choose Server --> Services --> Deploy --> View on Application or restart the J2EE engine
    • The problem is that not all J2EE services can be started by the J2EE. i.e Start the Visual Administrator and select Server->Services->Deploy in the tree on the left. On the right-hand side, choose the Runtime tab page. You see a tree in the right window with all applications if you select the APPLICATION radio button. Check if they are running, otherwise choose Start. Usually the J2EE engine starts all services automatically.
    • Refer SAP Note 803145,807000,791655
    You can have a look on this blog for the same.
    /people/krishna.moorthyp/blog/2006/07/23/http-errors-in-xi
    Regards,
    Sarvesh

  • Nokia Mail 'Unable to connect with information pro...

    Hi,
    I've just obtained a Nokia 5800 and am trying to set up e-mail using Nokia Messaging 2.10. When I get to the set-up section it asks for an e-mail address, and when I enter my address it searches for a while then gives the error message 'unable to connect with the information provided. Please try again'.
    What am I doing wrong?
    Thanks

    NM can't find info about your e-mail settings (POP/IMAP, SMTP). You have to set this manually.
    ‡Thank you for hitting the Blue/Green Star button‡
    N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

  • E63 unable to connect to Netgear WGR614v7: invalid...

    Just bought a Nokia E63 and keen to try connecting via my wireless router.
    Sees the network immediately. Easy to setup. However, as soon as I try to connect to the internet (e.g. Google) it says WLAN:
    Unable to connect:
    Invalid WPA pre-shared key.
    I assume it is referring to the network or passphrase key. Well, just to be sure I changed it and then went in on my laptop and had to change that so it could reconnect. Laptop works fine (again); phone still a no go.
    Wireless router setup as:
    Region: Europe
    Channel 11
    Mode g and b
    Wireless AP: ON
    Broadcast: ON
    Security options: WPA-PSK [TKIP] + WPA2-PSK [AES]
    Enable WMM: DISABLE
    No wireless card access setup.
    WAN Setup  
    Connect Automatically, as Required   = yes
    Disable SPI Firewall   = unticked
    Default DMZ Server ...   = unticked
    Respond to Ping on Internet Port = unticked   
    MTU Size (in bytes)    = 1500
    NAT Filtering Secured Open = unticked
    Disable SIP ALG = SECURED
    Ideas anyone?
    Cheers,
    J
    Solved!
    Go to Solution.

    jceh wrote:
    Originally I just followed the auto-setup and entered responses as required. Since then I've been trying different combinations trying to get it to work. Currently I go in through: menu > tools > settings > connection  > access points and then select my router SSID.
    Data bearer: wireless LAN
    Network status: public
    WLAN network mode: infrastructure
    Security mode: WPA/WPA2
    WPA/WPA2: pre-shared key
    Pre-shared key:  = router pass key (note this contains odd characters such as £ and % and commas.)
    WPA2 only mode: off
    All advanced settings (IPv4 etc) are automatic.
    J
    Looks allright to me. Use another key without the special characters or spaces. Check the router for MAC filtering. If you're using DNS servers you have to define them in the IPv4 section, if not leave it automatic (DHCP). Turn off the powersaving in the WLAN settings. Tools-> settings-> connection-> WLAN-> options-> advanced settings->yes-> powersaving-> off.
    ‡Thank you for hitting the Blue/Green Star button‡
    N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

  • Nokia 5800 - Unable to connect WLAN

    Im trying to connect my Nokia 5800 to my network at home via the WLAN. I'm using a netgear DG834PN with Security Option WPA-PSK (Wi-Fi Protected Access Pre-Shared Key). I have already disabled the security code once but i got the same error message. Any tips?
    Unable to connect
    No WLAN network find

    ok i also have the same problem before to but now to connect your phone to the computer by using the usb cable you must first go to "setting"--"connectivity"--then change the mode to "mass storage" or "data storage" after that your will be fine...i hope it work for you all  

  • Nokia N97 -- Unable to connect to Wifi?

    Hi,
    Ever since I got my Nokia N97 (Software vers: 12.1.024), I have been unable to connect it to Wifi. Under connectivity, it only gives me the option to add a 'packet data' access point, nothing else.
    Any reason why/way to remedy this?
    It also is unable to connect to my provider's 3G network -- my friend who has a N97 and is on the same network as I am has no problem doing so.

    Do you have the RM-506 China version? This version has no WLAN or 3g.
    http://www.forum.nokia.com/devices/N97/
    ‡Thank you for hitting the Blue/Green Star button‡
    N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

  • Nokia 500 Error in Connection

    I have nokia 500 which am using but i have some problem on it. I can't enter to ovi,email and to the store whenever i could try it tells me error in connection i thought was a problem to the network operator and try to change several operator but still am experiencing same problem please anyone help me
    Moderator's Note: A more appropriate subject was provided.

    Most applications use whatever access point is Priority 1 in Menu > Settings > Connectivity > Settings > Network destinations > Internet.
    Also worth checking to open browser > tap three horizontal line icon at bottom right of screen > Settings > General > Access point - temporarly change to "Ask when needed".
    If you change SIM required network access point may be found in 'Uncategorised" and need to be moved to "Internet" by longpress to reveal further menu options.
    Happy to have helped forum in a small way with a Support Ratio = 37.0

  • Cisco RV042 VPN unable to connect to Netgear PS FVS318

    Hello,
    We recently replaced one of two Netgear ProSafe VPN FVS318 with a Cisco RV042 VPN. Both Netgear were configured site-site and was working fine until one of them failed. We copied as much configuration settings from the failed Netgear PS to the RV042 but were unsuccessful in establishing a connection between the two sites.
    The logs on the Cisco router shows this:
    VPN Log packet from 1.1.1.1:500: received Vendor ID payload [RFC 3947]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n]  
    VPN Log packet from 1.1.1.1:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n]  
    VPN Log packet from 1.1.1.1:500: [Tunnel Negotiation Info] <<< Responder Received Main Mode 1st packet  
    VPN Log packet from 1.1.1.1:500: [Tunnel Negotiation Info] <<< Responder Received Main Mode 1st packet  
    VPN Log packet from 1.1.1.1:500: initial Main Mode message received on 2.2.2.2:500 but no connection has been authorized with policy=PSK  
    Each time we select a tunnel test connect, that last message appears with "but no connection has been authorized with policy=PSK"
    *replaced actual IP with sample IP.
    Any ideas why this is happening?
    Thank you!

    Hello,
    It looks as RV042 receive phase 1 configuration from Netgear, but due to mismatch with it's phase 1 settings does not reply back.
    I can't be more specific as this could be anything in phase 1 - aggressive/main mode; the WAN IP addresses, encryption or SA lifetime. As well if any of the devices is behind NAT, the option NAT traversal should be checked.
    Regards,
    Kremena

  • Nokia c5 unable to connect with pc in pc suite mod...

    nokia c5 is unable to connect with computer via pc suite mode but it get connected via mass storage mode . So i am unable to connect internet in my pc through my mobile. Whenever i m connecting my mobile , hardware installer of computer can't install my mobile due to code 39 shown in Computer.

    is your pc with ovisuite? Try with pcsuite

  • NOKIA N8 - Unable to connect - WLAN Network not fo...

    also for NOKIA N8 THE SAME PROBLEM: Unable to connect - WLAN Network not found;I see my network in the wlan list (Tthe state is "knowed") but when i try to connect to it,i read: Unable to connect-wlan network not found;i tryed with: mac filter on/off,dhcp on/of,wep protection on/off,firewall router on/off,power saving in the phone on/off, but the problem is the same ever!..Niklas Savander,..where you are?..nokia is back?..but with the same problems!

    Well, I seem to have issues with WLAN as well.
    When I am approx. 10metres away from my Router, the N8 doesn't connect. However, I can connect to WLAN using my Nokia N900, Nokia E52 and my Netbook (Asus EEE1005HA). This is a N-router with standard settings. I have tried changing, the channels etc. but it doesn't resolve the problem.
    So is this a problem with the Nokia N8? I mean, all my other wireless devices work fine. I even tried changing the Wireless Interface type from N/B/G, to B/G but as I said before, the problem is still there.
    Hopefully this problem can be sorted with a software update, that is if the N8 finds it difficult to connect to Wireless Internet.
    P.S.: Tthere is another thread reporting similar problems. Here is the link.

  • Nokia 3230 unable to connect to internet via USB c...

    when i use CA-53 cable to connect to internet using nokia pc suite7.0.8.2 (one touch access) an error message pops up "unable to connect to the speified device make sure the modem is configured properly" but i can easily connect to internet via bluetooth   other functions like file manager , contacts , messages and back up can be accessed by using the CA-53 cable

    I called a vw dealership (in South Australia) today because I have an iphone5 and a Tiguan and experienced the same thing (after i had purchased the lightening/30pin adapter).
    I was advised that the media interface software is not compatible with iphone5.  VW will eventually update the software according to ol'mate at the dealership, but it will be at an expense to the consumer allegedly.
    I know that there is a iphone/vw media cable one can purchase from VW however, I believe this to only work with iphone4 or older?
    Maybe try an older generation ipod to use for the car if all ur music is in itunes?
    if anyone can correct me, I'd be more than happy to know... going to try my older generation ipad and see if there is any truth to the tale.... eventually.  Until then i'll stream via bluetooth :-)
    Sheree

  • Nokia N85 unable to connect to Ovi Suite

    I am unable to connect my nokia n85 through usb for Ovi suite and also the Nokia Download program. Whenever i connect the cable, it tells me
    "your device is in file transfer connection mode and cannot be used with NOkia Ovi Suite. Quit file tranfer mode from the device if you want to use the device with Nokia Ovi Suite"
    The problem is i have no idea how to do this, and whenever i connect my usb cable my phone asks me which type of transfer method and i always select pc suite, so it shouldnt give me this error.

    plese help me for fixing this issue: Mine is nokia n85 smart phone. After installing ovi suite in my PC with windows 7, and updating all the software from nokia support, I am unable to connect my mobile to ovi suite through USB. It says," device does not support (though in phone it shows connected in PC suite mode). Please suggest me with 2 alternative methods so I can use one in failure default. Thank you

  • Suddenly stopped connecting to Netgear WGR614 v8

    Forgive me if this has been asked before, but as I was scrolling through posts, I found similar problems that didn't quite apply, but nothing identical.
    I bought a MacBook 1.5-2 months ago. Had some initial troubles connecting to my home network, but once I switched protection from WEP to WPA everything has been running fine. Yesterday morning I had to reboot my cable modem, which runs into a Netgear WGR614 v8. That night, when I went to connect via the new MacBook, I got the error that airport could not connect to my network, please try again.
    My hardwired G5 Tower connects via the router no problem, and my wife's iBook connects wirelessly no problem. The MacBook was able to connect to someone else's unprotected network no problem, so I know the card in it is still good, as is the router. I checked and the right password was still being remembered.
    Any ideas?

    Hello,
    The files that lead nowhere bother me most I think. Can you explain that in more detail?

  • Nokia 500 unable to get to ring through car kit

    Hi can anyone help,
    I have just got a nokia 500 and although states it is connected to in car Bluetooth system, It wont ring through the system or on the phone, am I missing hitting a button or switching something over. Please help if you can.
    Cheers

    Which car kit are you using , did you also check whether the nokia 500 compatible  with your car system.
    If this post answers your question, you can help others by clicking the green accepted solution' button.
    Please ask your questions to the main board and not to my mailbox. Thank you.

  • Unable to obtain ip with wireless connection to Netgear WGR614 router

    Pardon my ignorance, I'm relatively new to the Mac world.
    I recently purchased an iMac and at the same time purchased a Netgear wireless router.
    When hardwired to the Netgear, I have no issues. I tried connecting via wireless, and keep getting the self-assigned ip address. My wireless network is detected and the Airport card connects...full strength. I also have a laptop running windowsXP, and it connects with no issues.
    I have tried some of the suggestions mentioned in the discussions. Power cycled the Netgear. Changed channels...from 11 to 10. That didn't help so I went back to channel 11. I have security disabled...trying to keep the configuration as simple as possible until I can get this working.
    If anyone can share some thoughts/ideas, it would be greatly appreciated.
    Thanks.
    -Tim

    I had to go into /Library/Preferences and dragged SystemConfiguration to my desktop. I restarted the iMac.
    After it booted up, I went into System Preferences => Network; created a new Location and used the "Assist Me" tab at the bottom. It walked me through setting up the Airport again and this time it worked.
    For anyone that does this, once you confirm your wireless connection is working, take the SystemConfiguration on the desktop and drag it to the Trash.

Maybe you are looking for