Nokia 5800 Screen Problems After Firmware Update V...

Hi all,
I have the Nokia 5800 navigation edition. I just updated the firmwareon it from V40. to the latest available 51.2.007. Doing so has turned the phone's screen into a huge mess - the lower half of the screen is all white and the upper half has some weired flickering and the icons(the ones that are visible) are all messed up too and some of them are not responding at all.
Heres what I've done to resolve the problem:
- remove the battery, memory and sim cards for a few hours.
- reboot the phone without the memory card(eliminating any corrupt setup files).
- reinstalled the V51.2.007 update several times using bothe the Ovi Suite and the older Nokia PC Suite updater.
- tried running the updates on all XP, Vista and Windows 7.
Can you please advise me of any other possible solutions I can try. Is there any way to revert back to the older firmware. The phone was working just fine before the update.
Thank you all for your help.

There is another way to hard reset your phone and it is as follows.
With your phone powered off, press and hold Green  + Red + Camera Keys. Then power on phone using the on/off button whilst keeping the three keys depressed until you see the Nokia Shaking Hands Logo.
Always remember to backup your phone before performing resets as your data may be lost.
This reset will revert the phone to its out of the box state, so it will revert back to the original version of Maps that came with the phone. However, this should be an issue as you can easily redownload and reinstall the latest again.

Similar Messages

  • Nokia 5800 XM: Problems after firmware upgrade

    Hello all,
    I upgraded my firmware to V 50.0.005, cause that's what Ovi store told me to do in order to download ovi maps.
    However, now, when I open my internet browser it automatically opens full screen which is really not my preference. But when I click "options" it just shuts down.
    Also when I enter Ovi store now, at first it seems fine but after loading an app page it crashes saying no more than "Something went wrong".
    Thanks in advance for your help.

    Hello, I'm afraid I don't have an anser to this, but I too appear to have the same problem. After upgrading to v 50.0.005 I get the following problems relating to web browsing. 1. If I attempt to download anything I get the following error :- Script alert: A critical internal service has failed. after which I click on OK and the browser/application shuts down (and the connection closes). This happens when web browsing e.g. when attempting to download a BBC podcast or using the Ovi Store application to download something. Also it happens whether I'm using my provider's 3G network or a wireless network. 2. If in the browser I click on "options" the browser shuts down. I admit that in order to get Ovi Maps I have previously debranded my phone in order to get the necessary firmware updates, but I haven't had this problem with any of the previous ones. FWIW the Ovi Maps application appears to work well and manage to keep the internet connection up for a long period when online. Does anyone else have this problem? Can anyone suggest anything or will we simply have to hape that the next firmware update comes quickly and cures the problem? Thanks in advance.

  • Nokia N82 wifi problem after firmware update

    Phone is restarting while connecting with WAP
    and invalid server name while putting wep key

    23-Nov-2006
    03:11 PM
    mobile_maniac wrote:
    Ishvin, I'm sure I've read somewhere that the firmware on your phone can't be downgraded.
    One question though... if the old 100% used to hurt your ears, do you really need the old volume levels back?! That may even be the reason it has changed if Nokia thought the same thing... I'm sure they wouldn't want you sending them a bill to get your hearing fixed! :-)
    yes this is true but stil i want it loud enough so i can't hear it outside. i just hope they put the volume back up on the next firmware

  • Problems after firmware update 52.0.007

    Hi,
    I got my phone back after the shop fixed a problem and updated the firmware to the latest version 52.0.007.
    But now I have following problems:
    I can't get the calendar anymore to show up on the homescreen, even after checking the checkbox to do so
    The Radio app. is gone
    Does anyone has a solution for this?
    Iwan

    It may sound crazy but sometimes you need to "hard reset" device after firmware update (beware all data erased) by keying in *#7370# followed by 12345 (default Nokia lock code unless altered by yourself). Sometimes UDP = User Data Prersevation feature of 5800XM can carry over corrupt entries when updating.
    Happy to have helped forum with a Support Ratio = 42.5

  • 5800 problem after firmware update

    hi!
    I updated my nokia 5800 yesterday to  the new firmware v50. But today the whole touchscreen does not work at all. Only the three physical buttons and the unlock button on the side works. I have tried to turn it of but it did not help. I took out the battery and the memory card but i have still the same problem. Does anyone of you know what is wrong?

    /t5/Nseries-and-S60-Smartphones/5800XM-hard-reset-after-upgrade/m-p/462564#M137151
    So.. might have to go for a Hard Reset.. but Take a Back-up before doing...
    --------------------------------------------------​--------------------------------------------------​--------------------------------------------------​--If you find this helpful, pl. hit the White Star in Green Box...

  • Internet problems after firmware update 5800

    Hi there,
    I own a nokia 5800 since about 4 months ago. I am very happy with it, but when I updated the firmware three days ago, problems occured.
    At first everything seemed fine untill I wanted to look something up on the internet. The device makes a connection and then when (I presume) it established one, it just shuts down the webbrowser again. Also when I try to go to the "Download!" section I get an "unrecoverable error. application shut down".
    I have set up the internet settings again to check if that was the problem but the problem wasn't solved.
    Any idea on what this might be?
    Thanks in advance 

    Try doing a factry reset on the handset.  Failing that, you could do a firmware reinstall.  A lot of people suggest a hard reset/wipe but I personally think that's seriously last resort if everything else doesn't work.
    Nokia N8 on O2-UK
    Firmware 022.014

  • Nokia 5800 screen problems when unlocking

    When I unlock my phone, I get horizontal and/or vertical lines - I can't use the phone during this time, because the display is so badly affected!
    After about 5-10 seconds, the home screen will show perfectly normal.  When I either lock the phone, or lock it manually, then unlock it a few minutes later the lines come back again!
    Is this a hardware or software fault? If it is a software fault, how can I resolve this annoying problem?
    5800 v20.0.012 -- 6500s v9.40 -- 6233 v5.43 -- 5140 v3.13

    I have exactly the same fault on my 5800 to the point where the phone is completely unusable.
    Used the "Contact Us" facility 5 days ago - still waiting for a reply/acknowledgment.
    I bought the phone in mid February so it was quite an early release model, V11 frimware, but the screen fault was there early on but only very occassionally. Had the phone updated to V20 but the problem was still there. However it got progressively worse until the phone became unusable. The screen can only be restored by powering off and on again but once the screen has gone into saver mode it cannot be restored via the unlock button, or any other means other than a power down.
    Sent the phone to the Nokia "Anovo" repair centre only to have it returned 10days later with exactly the same fault as I sent it in with. The return advice note stated that details of the repair would be found on the enclosed letter - there was no enclosed letter. The return form states that all phones sent in would be automatically updated to the latest firmware - mine wasn't, even though Nokia notified me 2 weeks previously to inform me that there was an update for my phone.
    Rang Nokia Care last week, (Thursday) to be told that someone would contact me by phone, (borrowed phone obviously, as I had stated my 5800 was unusable). Friday and I had not been contacted. Rang again Friday morning 10.30am only to be told someone would contact me. Left a contact phone number again. Friday afternoon - still no contact so rang again. This time I was informed that someone should have told me that I wouldn't be contacted until Monday as thet were all "Very Busy" - I wonder why. Today, Monday afternoon stil no one has been in contact so I suppose I am going to have to go through the whole routine again.
    I am very close to the point where I am going to give up and demand a refund for an item that is clearly "Not of Merchantable Quality" or "Fit for Purpose" which would be a shame as when it worked I was really pleased with it. I bought the phone outright so I have no contract redress so am completely in the hands of Nokia. I know that Nokia is a very large company and I am but a single customer but from all the forums I have lookes at since this saga started I am driven to believe that the 5800 is causing Nokia some serious problems.
    If I do finally get some acknowledge from Nokia I will inform this forum.

  • C3-01 Problems After Firmware Update

    After updating the firmware from v5.65 to v6.0 the phone lost some features -namely:
    Chat
    Media Player
    Ovi Store
    "Favorite Contacts" on homescreen
    default wallpapers
    Solved!
    Go to Solution.

    Finally, I've fixed the problem!
    Going back, I updated the phone from 5.65 to 6.0 via OTA(over-the-air) update -in other words, I updated the firmware using the phone while connected to my home wi-fi network.
    In desperation to find a solution, I hesitantly re-updated the phone... But this time via PC.
    I opened Ovi Suite and updated the phone -again, expecting it would reinstall version 6.0 .
    After the update, all the apps that I've lost came back.
    I then checked to confirm if it was indeed version 6.0 -alas, it was not... It was version 6.05.
    Now, everything is working as it should be; mail, chat, ovistore, calculator, favorite contacts on homescreen -everything!
    It feels good to figure it out all by myself.  Hehehehe!!

  • Dual screen problems after last updates

    Hello everyone,
         it was long time since our Arch gave me some problems, but then now I'm fighting furiously with dual screen configuration with new gnome. Let me explain.
    I upgraded the home PC that I hadn't update for months, so I updated more or less everything ... kernel, nvidia drivers, gnome, etc..
    The PC has always been dual screen (no twin view, without xinerama), two screens (one on a LCD monitor and one on a TV) where I could run separate applications independent.
    Now, after the update, when I launch any application in the second screen (the TV) it starts on the first (screen).
    Obviously I have't made any changes to xorg.conf before and after the upgrade. I also tried to recreate one with the nvidia-tools but nothing ...
    Can you help me? Someone had the same problem?
    I post my xorg.conf, I hope that someone has a hint. I can no longer watching movies on TV and it is very annoying!
    # nvidia-settings: X configuration file generated by nvidia-settings
    # nvidia-settings: version 1.0 (buildmeister@builder63) Wed Oct 1 15:10:25 PDT 2008
    # Auto-generated by Archie mkxcfg
    # Auto-generated by Archie mkxcfg
    #Section "DRI"
    # Mode 0666
    #EndSection
    Section "ServerLayout"
    # PS/2 Mouse not detected
    # Serial Mouse not detected
    Identifier "Xorg Configured"
    Screen 0 "Screen0" 1024 0
    Screen 1 "Screen1" LeftOf "Screen0"
    InputDevice "Keyboard0" "CoreKeyboard"
    InputDevice "USB Mouse" "CorePointer"
    EndSection
    Section "Files"
    # Additional fonts: Locale, Gimp, TTF...
    # FontPath "/usr/share/lib/X11/fonts/latin2/75dpi"
    # FontPath "/usr/share/lib/X11/fonts/latin2/100dpi"
    # True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
    RgbPath "/usr/share/X11/rgb"
    ModulePath "/usr/lib/xorg/modules"
    FontPath "/usr/share/fonts/misc:unscaled"
    FontPath "/usr/share/fonts/misc"
    FontPath "/usr/share/fonts/75dpi:unscaled"
    FontPath "/usr/share/fonts/75dpi"
    FontPath "/usr/share/fonts/100dpi:unscaled"
    FontPath "/usr/share/fonts/100dpi"
    FontPath "/usr/share/fonts/PEX"
    FontPath "/usr/share/fonts/cyrillic"
    FontPath "/usr/share/fonts/Type1"
    FontPath "/usr/share/fonts/ttf/western"
    FontPath "/usr/share/fonts/ttf/decoratives"
    FontPath "/usr/share/fonts/truetype"
    FontPath "/usr/share/fonts/truetype/openoffice"
    FontPath "/usr/share/fonts/truetype/ttf-bitstream-vera"
    FontPath "/usr/share/fonts/latex-ttf-fonts"
    FontPath "/usr/share/fonts/defoma/CID"
    FontPath "/usr/share/fonts/defoma/TrueType"
    EndSection
    Section "Module"
    # Load "type1"
    Load "ddc" # ddc probing of monitor
    Load "dbe"
    # Load "dri"
    Load "extmod"
    Load "glx"
    Load "bitmap" # bitmap-fonts
    Load "freetype"
    Load "record"
    # Load "synaptics"
    EndSection
    Section "ServerFlags"
    Option "AllowMouseOpenFail" "true"
    Option "Xinerama" "0"
    EndSection
    Section "InputDevice"
    Identifier "Keyboard0"
    Driver "keyboard"
    Option "CoreKeyboard"
    Option "XkbRules" "xorg"
    Option "XkbModel" "pc105"
    Option "XkbLayout" "it"
    Option "XkbVariant" ""
    EndSection
    Section "InputDevice"
    Identifier "Serial Mouse"
    Driver "mouse"
    Option "Protocol" "Microsoft"
    Option "Device" "/dev/ttyS0"
    Option "Emulate3Buttons" "true"
    Option "Emulate3Timeout" "70"
    Option "SendCoreEvents" "true"
    EndSection
    Section "InputDevice"
    Identifier "PS/2 Mouse"
    Driver "mouse"
    Option "Protocol" "auto"
    Option "ZAxisMapping" "4 5"
    Option "Device" "/dev/psaux"
    Option "Emulate3Buttons" "true"
    Option "Emulate3Timeout" "70"
    Option "SendCoreEvents" "true"
    EndSection
    Section "InputDevice"
    Identifier "USB Mouse"
    Driver "mouse"
    Option "Device" "/dev/input/mice"
    Option "SendCoreEvents" "true"
    Option "Protocol" "IMPS/2"
    Option "ZAxisMapping" "4 5"
    Option "Buttons" "5"
    EndSection
    Section "Monitor"
    # Warning: This may fry old Monitors
    # Very conservative. May flicker.
    # VertRefresh 50.0 - 62.0 # Extreme conservative. Will flicker. TFT default.
    # Default modes distilled from
    # "VESA and Industry Standards and Guide for Computer Display Monitor
    # Timing", version 1.0, revision 0.8, adopted September 17, 1998.
    # $XFree86: xc/programs/Xserver/hw/xfree86/etc/vesamodes,v 1.4 1999/11/18 16:52:17 tsi Exp $
    # 640x350 @ 85Hz (VESA) hsync: 37.9kHz
    Identifier "Monitor0"
    VendorName "Unknown"
    ModelName "Samsung SyncMaster"
    HorizSync 30.0 - 81.0
    VertRefresh 56.0 - 75.0
    ModeLine "640x350" 31.5 640 672 736 832 350 382 385 445 +hsync -vsync
    ModeLine "640x400" 31.5 640 672 736 832 400 401 404 445 -hsync +vsync
    ModeLine "720x400" 35.5 720 756 828 936 400 401 404 446 -hsync +vsync
    ModeLine "640x480" 25.2 640 656 752 800 480 490 492 525 -hsync -vsync
    ModeLine "640x480" 31.5 640 664 704 832 480 489 491 520 -hsync -vsync
    ModeLine "640x480" 31.5 640 656 720 840 480 481 484 500 -hsync -vsync
    ModeLine "640x480" 36.0 640 696 752 832 480 481 484 509 -hsync -vsync
    ModeLine "800x600" 36.0 800 824 896 1024 600 601 603 625 +hsync +vsync
    ModeLine "800x600" 40.0 800 840 968 1056 600 601 605 628 +hsync +vsync
    ModeLine "800x600" 50.0 800 856 976 1040 600 637 643 666 +hsync +vsync
    ModeLine "800x600" 49.5 800 816 896 1056 600 601 604 625 +hsync +vsync
    ModeLine "800x600" 56.3 800 832 896 1048 600 601 604 631 +hsync +vsync
    ModeLine "1024x768" 44.9 1024 1032 1208 1264 768 768 776 817 +hsync +vsync interlace
    ModeLine "1024x768" 65.0 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
    ModeLine "1024x768" 75.0 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
    ModeLine "1024x768" 78.8 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
    ModeLine "1024x768" 94.5 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
    ModeLine "1152x864" 108.0 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
    ModeLine "1280x960" 108.0 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync
    ModeLine "1280x960" 148.5 1280 1344 1504 1728 960 961 964 1011 +hsync +vsync
    ModeLine "1280x1024" 108.0 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
    ModeLine "1280x1024" 135.0 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
    ModeLine "1280x1024" 157.5 1280 1344 1504 1728 1024 1025 1028 1072 +hsync +vsync
    ModeLine "1600x1200" 162.0 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
    ModeLine "1600x1200" 175.5 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
    ModeLine "1600x1200" 189.0 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
    ModeLine "1600x1200" 202.5 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
    ModeLine "1600x1200" 229.5 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
    ModeLine "1792x1344" 204.8 1792 1920 2120 2448 1344 1345 1348 1394 -hsync +vsync
    ModeLine "1792x1344" 261.0 1792 1888 2104 2456 1344 1345 1348 1417 -hsync +vsync
    ModeLine "1856x1392" 218.3 1856 1952 2176 2528 1392 1393 1396 1439 -hsync +vsync
    ModeLine "1856x1392" 288.0 1856 1984 2208 2560 1392 1393 1396 1500 -hsync +vsync
    ModeLine "1920x1440" 234.0 1920 2048 2256 2600 1440 1441 1444 1500 -hsync +vsync
    ModeLine "1920x1440" 297.0 1920 2064 2288 2640 1440 1441 1444 1500 -hsync +vsync
    ModeLine "1800x1440" 230.0 1800 1896 2088 2392 1440 1441 1444 1490 +hsync +vsync
    ModeLine "1800x1440" 250.0 1800 1896 2088 2392 1440 1441 1444 1490 +hsync +vsync
    ModeLine "640x480" 43.2 640 680 744 848 480 481 484 509 -hsync +vsync
    ModeLine "768x576" 35.0 768 792 872 976 576 577 580 597 -hsync +vsync
    ModeLine "768x576" 42.9 768 800 880 992 576 577 580 601 -hsync +vsync
    ModeLine "768x576" 45.5 768 808 888 1008 576 577 580 602 -hsync +vsync
    ModeLine "768x576" 51.8 768 808 888 1008 576 577 580 605 -hsync +vsync
    ModeLine "768x576" 62.6 768 816 896 1024 576 577 580 611 -hsync +vsync
    ModeLine "800x600" 68.2 800 848 936 1072 600 601 604 636 -hsync +vsync
    ModeLine "1024x768" 113.3 1024 1096 1208 1392 768 769 772 814 -hsync +vsync
    ModeLine "1152x864" 81.6 1152 1216 1336 1520 864 865 868 895 -hsync +vsync
    ModeLine "1152x864" 119.7 1152 1224 1352 1552 864 865 868 907 -hsync +vsync
    ModeLine "1152x864" 143.5 1152 1232 1360 1568 864 865 868 915 -hsync +vsync
    ModeLine "1280x960" 124.5 1280 1368 1504 1728 960 961 964 1001 -hsync +vsync
    ModeLine "1280x960" 129.9 1280 1368 1504 1728 960 961 964 1002 -hsync +vsync
    ModeLine "1280x960" 179.0 1280 1376 1520 1760 960 961 964 1017 -hsync +vsync
    ModeLine "1280x1024" 191.0 1280 1376 1520 1760 1024 1025 1028 1085 -hsync +vsync
    ModeLine "1400x1050" 122.6 1400 1488 1640 1880 1050 1051 1054 1087 -hsync +vsync
    ModeLine "1400x1050" 149.3 1400 1496 1648 1896 1050 1051 1054 1094 -hsync +vsync
    ModeLine "1400x1050" 155.8 1400 1496 1648 1896 1050 1051 1054 1096 -hsync +vsync
    ModeLine "1400x1050" 179.3 1400 1504 1656 1912 1050 1051 1054 1103 -hsync +vsync
    ModeLine "1400x1050" 214.4 1400 1512 1664 1928 1050 1051 1054 1112 -hsync +vsync
    ModeLine "1600x1200" 280.6 1600 1728 1904 2208 1200 1201 1204 1271 -hsync +vsync
    Option "DPMS" "true"
    # HorizSync 28.0 - 78.0 # Warning: This may fry very old Monitors
    EndSection
    Section "Monitor"
    Identifier "Monitor1"
    VendorName "Unknown"
    ModelName "TV-0"
    HorizSync 28.0 - 33.0
    VertRefresh 43.0 - 72.0
    EndSection
    Section "Device"
    Identifier "Card0"
    Driver "nvidia"
    VendorName "All"
    BoardName "All"
    EndSection
    Section "Device"
    Identifier "Videocard0"
    Driver "nvidia"
    VendorName "NVIDIA Corporation"
    BoardName "GeForce 7300 LE"
    BusID "PCI:4:0:0"
    Screen 0
    EndSection
    Section "Device"
    Identifier "Videocard1"
    Driver "nvidia"
    VendorName "NVIDIA Corporation"
    BoardName "GeForce 7300 LE"
    BusID "PCI:4:0:0"
    Screen 1
    EndSection
    Section "Device"
    Identifier "Device0"
    Driver "nvidia"
    VendorName "NVIDIA Corporation"
    BoardName "GeForce 7300 LE"
    BusID "PCI:4:0:0"
    Screen 0
    EndSection
    Section "Device"
    Identifier "Device1"
    Driver "nvidia"
    VendorName "NVIDIA Corporation"
    BoardName "GeForce 7300 LE"
    BusID "PCI:4:0:0"
    Screen 1
    EndSection
    Section "Screen"
    Identifier "Screen0"
    Device "Device0"
    Monitor "Monitor0"
    DefaultDepth 24
    Option "TwinView" "0"
    Option "TwinViewXineramaInfoOrder" "CRT-0"
    Option "metamodes" "CRT: 1280x1024 +0+0; CRT: 1024x768 +0+0; CRT: 800x600 +0+0; CRT: 640x480 +0+0"
    SubSection "Display"
    Depth 24
    EndSubSection
    EndSection
    Section "Screen"
    # Removed Option "metamodes" "TV: nvidia-auto-select +0+0"
    Identifier "Screen1"
    Device "Device1"
    Monitor "Monitor1"
    DefaultDepth 24
    Option "TwinView" "0"
    Option "TwinViewXineramaInfoOrder" "TV-0"
    Option "metamodes" "TV: 1024x768 +0+0"
    SubSection "Display"
    Depth 24
    EndSubSection
    EndSection
    Writing the post a tried to install fluxbox, and then... all ok. In fluxbox all works fine. I think this is a problem related to the new gnome screen configurer.
    I post an image of gnome screen configurer vs nvidia-tools.
    Googling around I found that new gnome screen configuration (using xrandr) is not compatible with nvidia drivers. Could be this the source of the problem?
    Help please
    Last edited by frullino (2008-10-25 13:17:29)

    Hi,
    Does your Mac go to the sleep status when you close the cover? If so, the remote session can be terminated due to time out and the time out value may be redesigned in the latest versions.
    Thanks.
    Jeremy Wu
    TechNet Community Support

  • Audio in problem after firmware update

    hey all,
    I've recently started using garageband to record and play around with my music, and I love it. Unfortunately, after installing the recent firmware update, my computer's audio in jack doesn't work anymore. It recognizes that there's something plugged in, but instead of having an signal, I get this clicking that clips the audio input at almost any input volume. I have tried it both with my bass and just the cable, and I have also just plugged some headphones into the jack- same results for everything. Is there anything i can do about it or do I just have to wait for another firmware update before I can use garageband again?
    2.2Ghz Macbook Pro   Mac OS X (10.4.10)  

    well what happened was I was updating iTunes (7.3.1) and the updater said a quicktime update and a firmware update were both available so I downloaded and installed and now the problem. It's like a really fast click track when I plug in and it's not just in garageband, I'm getting it in the audio-in option in the system preferences menu. Do you think doing a system restore would solve this problem?
    PS- I believe the update was something along the lines of a "kmbp firmware update" I think that's what it was called... :/

  • Overheating problem after firmware update

    Hi,
    A friend of mine noticed a CPU temperature increase in between 10 and 15 per cent, after the MacBook EFI Firmware Update 1.1. Has anyone else noticed a similar behavior? Any ideas or suggestions?
    Thanks in advance,
    Gonzalo

    Originally Posted by ketter
    HP DL380 G7
    OES 11 SP1 / SLES 11 SP2
    patched up to March 29, 2013
    HP LTO-5 Ultrium 3000 tape drive
    Arkeia backup software
    Everything was running fine. I updated the server firmware using the
    HP Proliant Service Pack on Apr 10, 2013 and haven't been able to get
    a good backup since. Arkeia support says problem with the hardware.
    But testing with the HP diagnostics says the hardware is fine. I
    checked with HP support and they agree that the hardware is fine but
    there are some communication issues. They recommended that I upgrade
    the driver. They sent me here:
    HP Smart Array P212 Controller*-* * RECOMMENDED * HP ProLiant Smart Array Controller (x86/AMD32) Driver for SUSE LINUX Enterprise Server 11 (x86) - HP Business Support Center
    I attempted to install that, but it failed due to dependencies. So
    before I go any further and risk messing something up. Does anyone
    have suggestions for this? If I do need to update the driver, is
    there another way I am supposed to do it vs using the driver from the
    HP website? Or how do I deal with the dependency issues...the only
    patching I have done with SLES so far is through the channel.
    Ken
    may i ask what kind of dependency issues you're facing? i've installed the SP2 (kernel 3.0.x) based package last weekend without any issues on a default kernel. are you sure that you've grabbed the rpm matching your kernel version?

  • N78 problems after firmware update

    I have recently updated my N78 (RM235) firmware to 13.052.231.6.
    Before the update the internal GPS worked very well, finding satellites quickly and holding a strong lock. After the update the GPS is very poor, taking a long time to find satellites and loosing signal very easily.
    Can anyone help with this problem or tell me how to re-install the previous firmware?

    Has everything else stayed the same and only the GPS antenna reception got worse?
    If that is the case you are right, but maybe the update made other improvements and for some reason one of them worsened the GPS antenna...just guessing...  
    By clicking the "Kudos!" or the "Solution?" button on the right you can say "Thank You" and you´ll show the author and others that the post is useful.
    The day we stop improving is the day we stop being good.

  • Problems after Firmware update

    I have a big problem with my ipod nano, @ the firmware update it disconnects from pc and now it didn't work anymore because of a mistake in the firmware what can i do? please help me

    If you have symptons stated on this thread, try the steps there.
    http://discussions.apple.com/thread.jspa?threadID=544840&tstart=0

  • E3000 problems after firmware update

    It seems internet browsing doesn't work after the firmware update.  Everything else works , aim steam msn, bittorent but anything http related will not work.

    on both computers i have run some tests
    ping 127.0.0.1 -fine
    ping 192.168.2.1 - fine (gateway)
    ping 192.168.2.3 (another computer) fine
    ping 192.168.2.254 dsl modem (fine)
    ping www.comcast.net fail
    I have thought it could be the DSL modem but it works  just fine when i use my Belkin pre-n router and the Belkin never needs a power cycle.
    I can get HTTP functions when i reboot the router. 
    I have also set up a DYNDNS to see if a friend could ping me and connect to  a server for me thru my IP address and it was successful its just websites and this is happening on all the computers and playstations (theres 2)

  • Sony SBH50 Multipoint problem after firmware update

    I recently updated the firmware on Sony SBH50 bluetooth headset and now, I cannot use Multipoint anymore.  I have to switch off and pair individual devices while Multipoint was working well before the firmware update.  Please advise what to do

    I just purchase it and I cannot connect to my Z3 in same time as my Z3 tablet compact.  it is last version of soft and on firmware

Maybe you are looking for