Nokia 603 cannot turn on , problem with ON button

Hi, I'd appreciate if anyone could help me
My nokia603 ON button works fine when the phone is already on, meaning i can press it to switch the phone off, but when the phone is off, and try to turn it on again by pressing the on button, it doesnt respond. any reason for that?
currently my phone is off, so i m having a lot of problem turning it on. any ideas on how to turn it on? i've tried connecting it to the charger and computer but it just doesnt respond
also as a last resort, is there any way i can transfer data from my dead phone to my computer without turning on the phone?
I really appreciate any help for my questions, thanks a lot for reading
Solved!
Go to Solution.

Hello Hans, thank you for your advice
I managed to get my phone started after hours of pressing the on button and hoping for a response. Now it's already turned on and I plan not to turn it off again or else I will have to go thru the same process of trying to get it back up. It works fine when it is already on
I think unplugging and plugging in multiple times serves the same function as pressing the on button many times. I've tried that too, but it just happened that I got lucky while pressing the on button instead of while plugging it in
Yes my phone definitely has hit the ground a few times, but definitely not from a dangerous height. Maybe 2 feet off the ground? And yes also liquid damage but also a bit, like when I use it during a drizzle?
I've brought it to get checked , its not a battery problem they said. but they cannot do anything because its an old model.
Thank you for your helpful ideas. I guess the best way is to just buy a new phone and move on

Similar Messages

Problems with home button on iPhone 4

problems with home button on iphone 4

If its due to sensitivity issues, these self help guides might help.
http://www.youtube.com/watch?v=zNwr_mxgs9Q
http://www.youtube.com/watch?v=lSqPC1V0PPg&feature=related
By the way, alcohol based hand sanitisers work too.
Don't overapply it in one go though. You'll have to allow the alcohol to evaporate.
One final tip, after its dried, I'd recommend you to leave your iPhone's home button facing a laptop's vent just to bake it a little drier.

Grey screen with message "turn off computer with power button until switch off then press again power button"

Dear all,
I'm very hungry with my iMac and my Time Capsule :
I try for two weeks to restore my iMac without any success...
I wait 80 hours to finally have the message again and again : "to restart your computer : turn off computer with power button until switch off then press again power button".
But my iMac do not work !
Could you help me?

Hello, that's a kernel panic...
http://thexlab.com/faqs/kernelpanics.html
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X 10.6 Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.

Problems with parameter button in Crystal Report Server 2008

Dear all,
I have problems with parameter button in Crystal Report Server 2008.
when I created some parameters and groups in Crystal Report 2008, they showed both parameters in 'Parameter button' and group in 'Group button' on the left, so I can choose or type without clicking 'Refresh button' But when I added it to Crystal Report Server 2008 and I click parameter button , it doesn't show any parameter. Only click refresh button to choose them. On the other hand, for 'Group Tree' is ok. When go to Default Setting-> Parameter, all parameters are in 'Unused parameter' First time I think I had problems with my installation, but when I reinstalled it again, it was like before.
Could any one help me with this?
I appreciate looking forward to your reply
Ketya

Try posting your questionin the correct forum, this is for SAP Business One, not Crystal reports Server

Problem with Information button in WAD

Dear Mates,
I have a problem with Information button in WAD template.
I have two queries in web template. those two queries are in two tabs( i used Tabstrip ) respectively.
if i press first tab it shows query1 and if i press second tab it shows query2 absolutely.
problem
when i am in first tab, if i click information it will show information about query1, but when i am in second tab,
if i click information it will show information about query1 only..
i need it to show information about second tab.
Please help. Its urgent. Full Reward points will be given.
Thanks in advance.
Regards,
Ranganath

check out this link
http://www.mhprofessional.com/downloads/products/0071640266/0071640266_chap01.pdf

A really annoying problem with a button/movie clip

I am having a problem with a button! its driving me insane
because i managed to do it last week, but that was by chance and
now i can't remember how i did it!
I can get the button (i'm using gelright from the common
libraries panel) and convert it to a movie clip(by pressing F8) and
even attach a behaviour but when i play the movie it doen't work!
when i move the curser over the button it changes into a hand, but
will not act like a button, even though i have set the behaviour to
'on release, go to and play keyframe 2'.
Please help me, for the sake of my laptop goin through the
wall!

virgosam20 wrote:
> first, i found the button i wanted in the common
libraries (gelright) and
> added it to the stage. I resized it and converted it
into a symbol as a movie
> clip. Then it got added to my library.
> Then i deleted it from the stage and replaced it with
the movie cip version i
> had just converted it to. so now i have the same object
on the stage, but now
> its a movie clip and not a button.
ok - you are running yourself around in circles - why did you
delete it to the stage only to add it
again? once you converted it to a movie clip, you had what
you wanted on the stage - but then you
deleted it and dragged another instance of the same symbol
back onto the stage - there's no reason
to do that.
> Then i double clicked on it to bring up the movie clip
timeline, but instead
> of saying 'top, down, over, hit' (or whatever it says),
it jsut said 'layer 1'
> (but this was not my original stage as i have a number
of layers on that one).
Right - this is expected because yoyu are now inside the
movie clip timeline - not the button timeline.
> When i double clicked on it again, it brought up the
right headings (top, down,
> over, etc),
Right - because by double clicking the button symbol you were
then brought to "edit mode" for the
button symbol.
but there were about 5 layers that showed the different
layers for
> the original button.
Huh? What "5 layers"? What do you mean "original" button -
per your description there has only ever
been 1 button you have been working with.
> I think i have to add the button to each of the
headings, bt there is no room,
Lost you completely now - what do you mean add the button to
each heading? I have no clue what you mean.
> as when i did it before, there was only one layer for it
and i had to insert
> the key frames myself.
Still losing you here.
> I then added a behaviour to it using the Behaviours
pannel, (selected
> movieclip, then 'go to and play....') and it appears in
the behaviours pannel.
> But when i got to Play Movie, although the curser
changes into a hand, the
> button does not work.
That's because you are applying a behavior for a button to a
movie clip instead.
I think you went wrong when you converted the button to a
movie clip - i have no idea why you did
that or why to think your button needs to be in a movie clip.
>
> Hope that can help you with what i've done and you can
tell me where i've gone
> wrong.
>
I just think you don't understand how timelines, symbols or
buttons work yet in flash.
1. drag a button to the stage.
2. select it and open the Behaviors panel (dont double click
it to edit it).
3. add your actions.
4. test movie.
(no need for a movie clip here.
-chris

Problem with the button

Hi my name is Lior Sassi from Israel. I bought an iPhone 5 in Amsterdam. Now I have a problem with the button on the iPhone and I still have a guarantee. Where can I fix the problem?

The Warranty is only valid in the Original Country of Purchase.
For Troubleshooting your button issue... See Buttons and Switches here...
http://support.apple.com/kb/TS2802

Problem with sleep button

I have problem with sleep button on my hp pavilion dv6-1354us When i press FN + F5 nothing happend. I reinstalled drivers for hp quick lunch buttons but the same problem.. Any solutions ? Thanks.

The operations of FN functions mainly based on the intrinsic working between the drivers and System BIOS.
If you already upgraded the Quick Lanuch Driver, then you may want to upgrade your System BIOS to the latest one in HP website to see if it can resolve the problem for you.
However, you need to be careful while upgrading your System BIOS.

Hey everyone I am haveing problems with Flash Button

Hello everyone I am new here so I am haveing problems with
Flash Button because of the html address it wont go to the address
that i put into it it keep going to
http://www.faithdesigner.net/www.faithdesigner.net/pricing.html/www.faithdesigner.net
why does it do that? this is a link problem issue with flash
button in macromedia dreamweaver 8?
someone please help me?
Jeremy

>
http://www.faithdesigner.net/www.faithdesigner.net/pricing.html/www.faithdesig
> ne
> r.net
In the dialog box for the Flash Button, in the link box, put
the full
absolute path if an external page. Including the
http:// part.
http://www.example.com/page.html
for pages inside your site- use the browse to file icon, and
use a relative
path.
Alan
Adobe Community Expert, dreamweaver
http://www.adobe.com/communities/experts/

Problem with Masked Buttons

As it stands i have a button called Start, when this button is hovered over, three more buttons appear at its side (all masked)
I'm having trouble actionscripting the buttons, ive tried putting the AS on the button
on(release){
gotoAndStop(2);
seen as everything so far is done on the first frame on various layers i just need it to go to frame 2. but this doesn't work.
the code that's on the start button is
on(rollOver){
Startmenu.play();
Start menu is the invisible movieclip which has the masks and rollout buttons in.
anyone got any ideas?

start button does overlay the other buttons and it is on the main timeline. as is the movieclip which activated the 3 buttons when the start button is rolled over with the mouse.
Date: Fri, 26 Mar 2010 08:39:42 -0600
From: [email protected]
To: [email protected]
Subject: Problem with Masked Buttons
does your start button overlay the other buttons?
is your start button on the main timeline?
is the movieclip with the 3 buttons on your main timeline?
does that movieclip respond to the mouse (and thereby intercept mouse events intended for the buttons it contains)?
>

Problem with the buttons

Recently I have problems with some buttons on my 8800.
When I hit the trackball the BB writes "Uo". When I hit the 'back' button it writes "Hl". Also the menu button does not what he has to do. Anyone the same problem or even better a solutions for this problem?
Bye, Ben

You are not alone. the same thing happened to me today with my 8820.
it worked fine for one call then i hung up and tried looking up a number. Track ball dosn't work at all, their isnt even a backlight on the trackball. the back button types in hl. i also think my e button is enter but i dunno. that one seems on and off.
Edit. I found this:
http://www.blackberryforums.com/general-8800-series-discussion/114752-blackberry-button-problem.html
Message Edited by jasgud on 07-27-2008 08:25 PM

Problem with option buttons

Hi!
We have a problem with Option buttons.
Example: We create a new document , then we add a group of Option buttons, so far no problem, but we can't have different description on each button. Say we create four option buttons, option 1, option 2, option 3 and option 4. They are now grouped together so that we can only choose one option, but we also want to have different descriptions on the tooltip when the user hovers over. But when we set for example "Option 1" as a description on the first button, all buttons get the same description, what is wrong!
Dan

A field's Tooltip entry is a "child" of the field's Name (in the General tab of the field's Properties dialog).
So, all fields of the same Name will have the same Tooltip.
Perhaps this is the problem?
Be well...

A problem with the buttons

We are making a video game at school. and we are having
problems with the buttons. We are having problems with the action
codes. like gotoandstop. and things like that. it comes up that we
have errors do you have any possible solutions.
Thank you,
Blevins EAST

trx 450 wrote:
> We are making a video game at school. and we are having
problems with the
> buttons. We are having problems with the action codes.
like gotoandstop. and
> things like that. it comes up that we have errors do you
have any possible
> solutions.
> Thank you,
> Blevins EAST
Need more info or file source for us to check.
"My car does not work, what's up with that" is way too
general to even try to
suggest something.
Best Regards
Urami
!!!!!!! Merry Christmas !!!!!!!
Happy New Year
<urami>
If you want to mail me - DO NOT LAUGH AT MY ADDRESS
</urami>

A problem with rollover button

i have a problem with rollover button in the menus when i upload my site to the hosting server. When i preview in browser with Dreamweaver before upload , there are no problems.
Thank you!

You have not uploaded the images on the server which is why rollover is not working. When we put the url - http://modano.1gb.bg/button4a.gif in browser it takes the user to the home page of the hosting company. I think you need to check to make sure that the images are uploaded properly.
Regards.
Barbara Long

Problems with custom buttons

I have problems with custom buttons in Captivate 5. The button is not switching from the _up stage to _over stage, but when I click on it the _down stage works fine. It is not a problem with the naming of the buttons. They are all with the same name and in lower case. I have tried with various custom buttons and the problem is the same. There is no problems with the standard buttons from the Adobe Gallery, so it is a bit strange, also strange that it is only the _over stage that causes problems.
The buttons I have made in Adobe Illustrator. Have tried both exporting in png and bmp format. It is the same problem.
Hope someone has some idea as to what can be wrong.

Hi Manish,
I have uploaded the zip file with the button files to Acrobat and mailed you the link.
Look forward to hear if you find a reason or more importantly a solution :-)
Kind regards
Rene

Nokia 603 cannot turn on , problem with ON button

Similar Messages

Maybe you are looking for