Nokia 6101,camera won't work

Hi,
I am experiencing some problem capturing photograph with my Nokia 6101.Whenever I attempt to capture an object I keep getting "Operation failed" then " Camera on Standby'.
Can someone please assist me in restoring the original setting?
RegardsMessage Edited by satabee on 13-Mar-2006
11:55 PM

That happened to mine as well, but then I realized it was because of memory issues. Check out the memory card to see if it's full or if your main memory is the phone itself, check to see if it's full. If either one is full, just go into settings and change the memory use to the one that has room. If you're using the memory card and it isn't full, it may be because your phone isn't reading the memory card (this happened to me), my mem card was messed up. I just saved all the preinstalled data and reformatted my card. Hope this helps

Similar Messages

  • My Ipod 4th generations Camera won't work, how do I fix it?

    My Ipod 4th generations Camera won't work, how do I fix it?

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up                                                                
    - Restore to factory settings/new iOS device.             
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar                                      

  • Icon of camera won't work to send pic with text

    icon of camera won't work to send pic with text

    Howdy Mitzymom,
    Welcome to Apple Support Communities.
    It sounds like there is an issue sending texts with photos from the Messages app on your iPhone. If the issue only occurs in when tapping the icon in the Messages app, not when texting pictures from other apps like the photo app, try the general app troubleshooting suggestions below on the Messages app.
    iOS: An app you installed unexpectedly quits, stops responding, or won’t open - Apple Support
    Restart the app
    Close the app and open it again.
    Restart your device
    Turn the device off and on.
    Update your device software and your apps
    Update your device to the latest version of iOS.
    If the issue occurs when trying to send texts with photos from any app, try the MMS and iMessage troubleshooting suggestions here:
    iOS: Troubleshooting Messages - Apple Support
    Take care,
    -Jason

  • Front face camera won't work for pictures. But it works perfectly on FaceTime, any way of fixing this?

    Front face camera won't work for pictures. But it works perfectly on FaceTime, any way of fixing this?
    When I try and change the camera to face front it acts like it's going to change then kind of freezes and won't let me change back to the back camera for several minutes.
    Any ways of fixing this?

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up                             
    - Restore to factory settings/new iOS device.
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar                       

  • Camera won't work. Newbie here.

    Hi guys I have just joined this forum and I wonder if you could help sort out my camera that say's .. "Could not start the camera. Close other applications and try opening the camera again."
    I've already tried wiping all my applications on Blackberry Curve 8520 still the same. Then I tried, putting my fone on safe mode same same. Then lastly I tried the 'Alt key + lglg" to see the event logs after I choose 'Clear Logs' and this what entails..
    Min Log Level is in 'Warning'
    a System - JVM: INFOp=286e737e,a='5.0.0.681',o='5.2.0.67',h=8c000f03 and when I clicked this..
    Name: System
    Severity: Always Logged
    GUID: 97c9f5f641d25e5f
    Time: Nov 14, 2013 12;28:07
    JVM: INFOp=286e737e,a='5.0.0.681',o='5.2.0.67',h=8c000f03
    Next is ..
    W System - Overlay released (deleted) at index: 5
    Name: System
    Severity: Warning
    GUID: 97c9f5f641d25e5f
    Time: Nov 14, 2013 12;27:53
    Overlay released (deleted) at index: 5
    w System - New overlay at index:5
    Name: System
    Severity: Warning
    GUID: 97c9f5f641d25e5f
    Time: Nov 14, 2013 12;27:53
    New overlay at index: 5
    W System - PMEU 1037
    Name: System
    Severity: Warning
    GUID: 97c9f5f641d25e5f
    Time: Nov 14, 2013 12;27:53
    PMEU 1037
    a net.rim.memclean - FrmF
    Name: net.rim.memclean
    Severity: Always Logged
    GUID: cb039f26e560f62d
    Time: Nov 14, 2013 12;27:53
    FrmF
    a net.rim.memclean - FrmF
    Name: net.rim.memclean
    Severity: Always Logged
    GUID: cb039f26e560f62d
    Time: Nov 14, 2013 12;27:53
    a System - JVM: INFOp=286e737e,a='5.0.0.681',o='5.2.0.67',h=8c000f03
    Name: System
    Severity: Always Logged
    GUID: 97c9f5f641d25e5f
    Time: Nov 14, 2013 12;28:07
    JVM: INFOp=286e737e,a='5.0.0.681',o='5.2.0.67',h=8c000f03
    All of these are on my event logs and still my cam won't work. Please help me with this.

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up           
    - Restore to factory settings/new iOS device.
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar          

  • My iPod camera won't work. The shutter doesn't open at all. I backed up and restored my iPod but it didn't make it work. Now I'm so mad and confused. Please help.

    My iPod camera won't work. The shutter doesn't open at all. I backed up and restored my iPod but it didn't make it work. Now I'm so mad and confused. Please help.

    If you restored to factory settings/new iPod via iTunes (Not via Settings>General>Reset>Erase all Content and Setting) and still have the problem that indicates a hardware problem.
    Make an appointment at the Genius Bar of an Apple store..
    Apple Retail Store - Genius Bar

  • My camera won't work on my Iphone 5

    My camera won't work! It comes up with a black sceen/ closed shutter! I've forced closed it, restarted my phone but nothing is working! I use my camera daily so  this is a huge issue!
    Could someone please help me solve this problem!?
    Thanks

    Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new).  Try each of these in order until the issue is resolved.

  • After last update, flash won't run, camera won't work, slow slow slow!

    After the recent update, my camera won't work, can't do facetime or video in ichat.  Also shockwave and silverlight plug ins won't work so can't watch youtube or netflix.  On reboot my laptop is EXTREMELY Slow!
    help?

    Hi hadleyoil, and a warm welcome to the forums!
    Thanks for the report(s).
    That is generally the best cure, just be sure to Repair Permissions before & after any update!
    The combo update for PowerPC-based Macs...
    http://www.apple.com/support/downloads/macosx10411comboupdateppc.html
    The combo update for Intel-based Macs...
    http://www.apple.com/support/downloads/macosx10411comboupdateintel.html
    Repair Permissions before & after re-install, then reboot again each time.

  • Torch won't turn off and back camera won't work after dropping it in a pool. What can I do?

    I put it in rice as soon as I got back, and left it for 36 hours as instructed by a website and friends. Ever since dropping it the torch hasn't turned off and the bac camera won't work.

    Water and electronics do not mix well.  Your device may not ever work properly again, and probably needs to be replaced.  Unless you have the AppleCare Protection Plan Plus, then it will cost $199 USD to replace an iPhone 4S.
    The rice trick works best if you leave it for at least 4-5 days, not 1.5 days.  But even that is no guarantee.

  • Nokia 6101 - camera on standby?

    hi,
    I wonder if anyone could possibly advise me what to do with my phone (nokia 6101). I tried to use the camera recently only for it to come up with "operation failed" after a couple of seconds, and then "camera on standby". After pressing continue it again came up with "operation failed" and it goes on and on etc...
    I've had problems with the phone before (dead pixels after 1 day) and had it replaced in around Jan/Feb, so I was wondering if the warranty with nokia is still valid on this 2nd phone (if there even is one), and if the above problem could be fixed!
    Thanks
    x

    Same problem on my 6101 (3 weeks old). Removing both the battery and SIMM for serveral minutes worked once but the fault has returned. Looks like I'll have to send it away for repair or replacement under warranty.

  • Problem with Nokia N73 -- Camera is not working

    Recently i have purched Nokia N73.
    Some times my camera is not working ,means it's stuck.
    but after some time or after a day it's working fine.
    what is the reason ?
    is there any setting?
    Plz let me know the same.
    Wating for your positive reply ASAP.

    try to upgrade your software
    see this link-> http://europe.nokia.com/softwareupdate

  • N82 Camera won't work

    Hello, I've had my N82 for about 6 months, Every time I try to turn on the camera the symbol that shows the flash is charging comes up but the camera never comes up. All I see is a black screen. Could it be the battery? I got this from Dubai and I live in the United States. Please help! I have the most recent firmware. And my battery is full.
    Message Edited by hotice on 07-Jun-2008 11:13 PM
    Message Edited by hotice on 07-Jun-2008 11:16 PM

    check your battery via nokia energy profiler.if its work fine.
    you should reset your phone:
    1.backup your phone
    2.press and hold these three keys(call,3,*)
    3.press power key while holding three keys.
    4.nokia logo or whatever shows phone living(like time setting) is shown.
    5.release keys.
    -your problem should be solved
    Have a good time.
    if i was helpful,check the below box.
    NOKIA means:Night Of King In Alone

  • My camera won't work with IMAQ vision builder

    I have a Hitachi camera , and a PCI 1407 frame grabber
    the camera works well in MAX under devices , but when I open the IMAQ vision builder , it not visible in the devices , and I can't open MAX from the vision builder. It's gets me that error "1074397163" at the end it has bad interface
    it's not the power supply of the camera since it works well at MAX , so its like the camera's name is img0 in MAX , and another thing in IMAQ vision builder, I tried updating my softwares but nothing happened, can anyone help please ??
    thanks

    Dalia, 
    I think I may need some clarification on what exact program and function you are using. Are you getting this error with the Vision Builder for Automated Inspection (VBAI)? Or are you using LabVIEW and are receiving this error from the IMAQ Init.vi?
    If it is in VBAI, and you are trying to acquire an image, the Devices should auto-populate in the Main tab of the Acquire Image setup. Simply select the camera and press Grab or Snap. 
    If it is in LabVIEW, right-click on the interface input of the IMAQ Init.vi to create either a constant or a control. If it does not auto-populate with the correct camera name as it is in MAX, "img0". Or you can change the interface name in MAX by simply right-clicking on the camera and selecting "Rename"
    Can you elaborate on what you are referring to when you say "the MAX explorer won't work in IMAQ"?
    Huntington W
    National Instruments
    Applications Engineer
    ***Don't forget to give Kudos and Accepted as Solution where it is deserved***

  • IPad2 camera won't work and it takes 5 1/2 hrs to charge battery

    My ipad2 is about 2 and a half months old and everything was working fine until a few days ago.
    First my iPad froze in the middle of one app and I couldn't restart the device. I tried to press the home button but it didn't work. I then tried to restart the iPad by holding down the sleep button but nothing happened either... So I left the iPad alone for about 5 mins and the apple logo appeared out of nowhere and  took me to the lock screen (where u have to slide the bar to load the home screen). After that everything went back to normal.
    Second, my camera stopped working. Every time I press on the camera, it goes to the shutter screen and stays there. I restarted my iPad but the camera app still won't work. FaceTime and photo booth works fine though.
    Third, now my iPad takes over 5 and 1/2 hrs to charge from 0% to 100%. When I first got my iPad, it only took it 4 and 1/2 hrs to charge from 1% to 100%. I have heard that over time, it should take less hrs to charge the iPad (not more).
    Any suggestions on how to fix this?
    Thanks u

    Try a reset, which is done by pressing and holding the home button and the sleep/wake or on/off button simultaneously until you see the Apple logo and then release. A reset does not affect any data or settings.
    The time it takes to charge the battery will not improve over time.
    http://www.apple.com/batteries/

  • Casio Camera won't work with SL

    My Casio EXZ850 camera doesn’t work with Snow Leopard.
    Used it with Windows XP & then with Leopard just fine. When connect to USB ports not recognized by Mac. I checked System Profiler.app & under USB it is not listed. Casio Support is no help. They say it won’t work with anything above OS X 10.4 which is incorrect as I used it with 10.5 for over 1 year with no problems.

    I take it that you ahve the IP set to static, or have a MAC address DHCP reservation for the camera, network settings OK.
    WHat was the wireless authentication on the old router and what are you using on the new 4200?
    Is it possible the camera does not support the encryption used by the 4200, i.e. wpa2-personal?
    Have you tried WEP to see if the camera will work then? 

Maybe you are looking for

  • Problem connecting an external display or projector to Retina Macbook Pro

    I have a problem with my rMBP (MAC OS:10.8.2) and i'm not sure if it is just an easy fix or if there is a serious hardware issue. I connect my rMBP to an external projector Hitachi CPX3011 (max resolution 1600x1200) very often for my presentation. I

  • Tag name: "embed" not found.... ?

    Every time i insert a swf file into my html file with DwCS3 generate this code: <embed src="flash/topheader.swf" quality="high" pluginspage=" http://www.adobe.com/shockwave/download/download.cgi?P1_Prod_Version=ShockwaveFlash" type="application/x-sho

  • Burning and Song Quality

    Hi, i've been having this problem for a while. I am burning mp3 tracks onto a CD-RW through iTunes. That seems to work fine and i import the songs of the CD but when i listen to the tracks then on my iPod i notice they are now often of bad quality in

  • SCCM 2007 to SCCM 2012 client migration via Powershell

    Hi I'm looking for a controlled way to migrate a SCCM 2007 server client to SCCM 2012. A push of SCCM Console is no option. I 'll do all the testing but hoped to gain some time by having these questions answered: *can an install of SCCM 2012 client b

  • Favicon keeps disappearing???

    Even though my favicon 32 x 32.png is loaded into each page site and added to upload files it often doesn't display, any ideas why?