Nokia C5 won't start

I have a recently purchased Nokia C5 that in mid conversation just died. No warningsignals or anything, it just died. Every time I start the phone it buzzez (vibrates) but not like it usually does, just a sort of warningbuzz or something and nothing happens. I tried charging it, thinking it may be the battery, but an hour later nothing has changed. It doesn't even show that it is recharging. I've tried taking out the battery, taking out the simcard, taking out the microsd and all at the same time - Nothing!
What the h*ll is wrong with my phone?!

Next thing to try is a Hard Reset:
Press and hold these three buttons * + 3 + Green call button. now push the power on. keep those buttons pressed, until you see timezone selection screen.
(Buttons to hold are STAR, THREE, GREEN CALL BUTTON)
After doing this unfortunately you'll loose you data from phone memory, and it'll be in out of box condition.
And if Hard Reset fails, next thing is to visit your local Nokia Care point and let them fix it for you.
http://europe.nokia.com/support/repair-and-recycle/repair/care-points
Previous Phones: 6600, 7610, 6230, 6230i, 1100, 1112, N70, N73, N95, N95 8GB, 5800XM, 5230, C5, iPhone 3GS, SE Xperia X10, N900, N8, SE Xperia Arc
Current Phones: Nokia N9, iPhone 4

Similar Messages

Nokia 6288 won't start

Hello,
During updating my phones software by using NSU i got a warning the connection between phone and pc was lost so te update was not finished. Now my 6288 won't start anymore. Does anybody know how to solve this?

This is true, the phone has completely crashed and only an engineer can now get this working.
You can find the nearest NCP to you at the Store Locator
My posts are my opinion and in no way the direct views of Nokia.
If my posts are helpful, please give me some KUDOS using the green star on the left.

Nokia 301 won't start up

When I switch my Nokia 301 off, it won't start up again.
To get it to start, I have to remove the battery for more than 10 minutes, plug it into a charger for an hour or so, and then it will start up.
If I try to turn it on soon after plugging the charger in, the screen flashes brightly and then switches off, and I have to start again by taking the battery out.
Could this be solved with a new battery, or resetting or reflashing the phone, or is there something more serious wrong with the electronics?

Welcome to Nokia Discussions, glastounok.
This might be a hardware issue. You may send it to a Nokia Care Centre for further device diagnostics.
Nokia Care Point locator can be found at http://www.nokia.com/global/support
Good luck

Nokia 700 - won't start after FP1 update (112.some...

Just checked for updates today and I had a new OTA update available, yay! So I thought, "Finally, FP1 is here!" Here's what happened afterwards:
I charged my 700, created a back-up (never forget this step chaps), restarted it, took a deep breath, enabled Wi-Fi and let it update itself.
So first step went fine, it downloaded the update. Second, it rebooted and started loading the update files while displaying "Updating..." Next, it switched the label to a coups of gears and continued filling the progress bar. And then - the moment of truth - reboot.
Started initialising normally, then showed NOKIA logo, started the "Loading" animation with the five dots and... that was it. It keeps resetting while at the dots animation. After several tries it just gave up and remained blank. Waited some time and decided to wake it up - same scenario: starts init, several reboots, goes back to off.
Is it that the OTA SW updated screwed up my device? Really hope not!
Any words of advice from the community here before I go yell at somebody at one of my carrier's offices tomorrow morning?
Cheers!

Brief update - turns the phone is not "bricked" at all, problem is my SIM card.
It's ancient honestly but should that render the phone useless?
In short - tried booting without SIM at all - works OK. Tried with relatively recent SIM - OK. When tried with my old SIM (think I got it as a replacement to an even older price back in 1999 or 2000) - boom! Won't power up (keeps rebooting till it gives up at some point).
Although I'll easily remedy it by getting a new chip in the morning, I was wondering - is Belle FP1 not supporting old SIM cards?

Nokia 5800 won't start up three weeks after slight...

okay, here's kind of a long one.. I bought my nokia 5800 xpressmusic on a £5 a month contract with the catalogue 'Very'.. Apparently this does not include insurance.. Anyway.. the phone worked perfectly for a year.. until i went to the beach and dropped it in a shallow puddle face down.. slowly everything went off... so i took the battery, sim and memory card out.. a day later it came back on.. it's worked fine for three weeks (apart from the lights on the buttons and the secondary camera on the front).. but last night.. i was on my normal apps when the screen closed down, went black and the backlight was on low.. i tried taking the battery, sim and memory card out and put them back in.. but to no avail.. also I've tried it on charge and tried with a sim without, with memory card without etc.. but nothing seems to be working... this kind of thing has happened before but it came on after a few hours.. but it's been 12 hours.. and i haven't had any luck with it.. i could really use the help because i'm not even half way through my contract with 'Very' and they won't let me cancel it and they won't replace it... Also no message came up after the phone turned off..
The fact it crashed while i was on apps after it had worked for three weeks after the water accident makes me think it's probably not due to the slight water damage... can you help please?

serebro_ru wrote:
The fact it crashed while i was on apps after it had worked for three weeks after the water accident makes me think it's probably not due to the slight water damage... can you help please?
Don't know why you assume this especially due to corrosive nature of saline as opposed to fresh water; it takes a while for faults to start showing up after such immersion unfortunately.
Happy to have helped forum with a Support Ratio = 42.5

Nokia C7 won't start anymore

Hi all!
To briefly describe the problem:
- bought the phone 5 days ago; tried it to see how it works- installed PR1.2 as an update throgh phone's update function to have the latest software available;
- 3 days ago it suddenly stopped; It started again after five minutes (meanwhile I couldn't make it start whatsoever);
- yesterday while transfering a picture through OVI to the computer, the phone closed; I couldn't make it work again; I searched the internet and the only thing that worked was to leave the phone in the fridge for 5 minutes and then turn it on but it only works for some time then closes again;
From what I see in the other threads, this is a common problem. Is there any proper workaround available or the only solution is to get it back to the the store I bought it and hope they'll replace the motherboard? Is there anywhere any information regarding the source of the problem? (I read it's probable to be a sensor of heat)

Hello,
Regardless the reason what’s causing this issue and whether your phone
temporarily wakes up after being in fridge, the fact is that your new phone
isn’t working as it should. For that phone needs to be either checked by Nokia
Care point and then repaired or swapped by the retailer. As phone is brand new,
warranty naturally covers the costs.
Putting the phone into fridge for a while obviously isn’t a solution and if
done frequently, may even damage the phone more, as rapid temperature changes
cause air humidity condensing inside the device. Also opening the phone and
trying to repair according to some instructions found from internet causes the
warranty to expire, so I definitely wouldn’t recommend that either.

C3-01 won't start after charging

I'm so angry right now but I will try and be cool about this!
I bought C3-01 mobile phone about four months ago and it is already causing me problems.
The mobile phone simply won’t start after charging. Last time i charged it, it miraculously came to life only, and only after annoying me for about hour and a half. Now I fear it is completely dead!
Battery was not completely empty so the phone should still start even if the wall socket is broken. Which is not, wall socket works perfectly.
Nothing helps! I tried removing the battery and then restart. Removing the battery then removing the sim card, memory card and that piece of “advanced technology” simply won’t start!
I didn’t buy my new phone so that I can use my old Motorola mobile, which btw., still works after 4 years of intense usage.
I will never buy Nokia again!

Hi,
Sorry to hear that your phone is not starting after charging.
I would suggest one more thing, which maybe helps. If you have another battery, please try.
If not, i would recommend to visit Nokia Care Point in your area.
To find your nearest Nokia Care Point, visit http://www.nokia.com/support and select the Repair page.
Br
Mahayv

N97 Camera won't start

Hello everybody,
We I open the lenscover of my n97, the screen turns black (sometimes I see the buttons on the side, but not the option button) and the camera won't start. Also via the menu it doesn't work. The screen stays black and the only way to turn the camaera-application off is to turn the phone off.
I haven't done a hard reset yet, because I hope someone has got the same problem and could solve it easier.
Greetz,
John

if your phone updated to the latest firmware? and you just might have to consider the first two options. make sure you take your battery card out and back up all your data. the first option will restore default settings but you will not lose any data. try that and see what happens.
1. *#7780# - Restore factory settings - resets all the settings to the default ( you will not lose any data)
Make sure you back up your data as you will lose all of it when you perform option 2 or 3 on this list. The default code for ALL operations listed here is 12345
2. *#7370# - Reformat your phone (out of the box, tho keep in mind that most newer nokia phones at least n series, e series and s60 based phones have udp - user data preservation so not ALL data may be lost. still it is a good idea to always do a back up of your stuff.)
3. This you perform as a last resort. Nothing else is working.If the phone is not showing any activity, proceed with hard formatting , turn off your phone, hold the following buttons while pressing the power button. (the default code is 12345)
hard reset - hold the following buttons *, 3 (number button) and talk/green key. turn on the phone and do not release those buttons until you see the Nokia boot up screen. once you feel the phone power up you can let go off the power button while still holding all three buttons ( for Nokia 5800XM - use the following buttons to do a hard reset, GREEN/RED/CAMERA keys pressed all at once on power up. this will only work on 5800's that have firmware version 20... and up. )
If these codes are not working the only thing for you to do is contact your Nokia Care Center/Service for assistance.
You know what I love about you the most, the fact that you are not me ! In love with technology and all that it can offer. Join me in discovery....

E5 won't start after multitasking freeze

hi,
my E5 is shut itself afer using Opera Web + music + Palringo
i can't turn it on after, i need to wait for about 4 hours or more before starting it = it as soft reseted alone but how can i accelerate the process if i can't even turn it back on !
ps : nokia review advice for nokia E5 don't buy it ... go to Blackberry if you can !

December 21, 2010
To whom it may concern:
/t5/Eseries-and-Communicators/E5-won-t-start-after-multitasking-freeze/m-p/840827
The thread looks familiar to me. I just came from Nokia Care Center a while ago and left my Nokia E5-00 phone there with the same problem as everyone else on the thread.
I am from the Philippines and my Nokia E5-00 was made in Korea, sent to Hong Kong, and then sold here in the Philippines. That is a lot of cost saving activities to do.
I previously had my first Nokia E5-00 a week ago, Monday. It felt like I am the happiest man in the Philippines. You know, the "I have a Smartphone!" proud feeling of a young man.
But all excitements turned into saddening experience. My contacts are not accessible from theMenu and the Shortcut (default: right selection key) making it inconvenient to create a message or call a contact.
That was a different issue. So I made my phone replaced and last Sunday, 2 days ago, I had my new Nokia E5-00 unit.
Yey!
The contacts were good as all other applications were.
Then, I started having problems as everyone else in the thread experienced. The phone had a bad restart habit and it was, in fact, irritating. It was tolerable at first. Not bad for a replacement phone. I was not much bothered with the restarts.
Then, I was able to start utilizing GPS, like I would get lost. It was an amazing experience for someone here in the Philippines. I was proud to have a good working GPS in my phone!
But, unluckily, 30 minutes after the fun. I set my phone to go back to work and WALAH! My phone shuts down after transferring some files. Good thing my Nokia E5-00 finished all transfers before dying out.
It was not quite the Nokia Smartphone I expected. And, that was really disappointing. Thank you im_mobile for the term.
I did not expect to see these much people complaining problem with Nokia E5-00. Same as everyone else experienced.
How should Nokia fix this? I am not in the position to say this, but Nokia should (1) recall these defective Nokia E5-00 products (Thanks magnum_jon) and (2) replace all defective units from unsatisfied customers.
I think Nokia will not get hurt from returned phones. In fact, they will have the benefit of immediately finding out what the problem is and they will be able to fix this immediately if they get all of our defective Nokia E5-00 units. They can (1) isolate the problem, (2) test as many phones as they want, (3) find out the problem and (4) make a happy customer.
These much claims is not tolerable. This is degrading Nokia. I believe Nokia has seen much already, and I am hoping that by the time they read my post, it would be the last.
And the next reply to this thread would be a happy customer with a newly replaced, non-defective, Nokia device.
Thanks,
Eljun Pacomios.
Philippines

XM5800, Phone won't start up properly, doesn't loa...

XM5800, Phone won't start up properly, doesn't load after the Nokia Screen. Basicall I turn it on and it goes the Nokia screen and then my background pops up but then nothing else happens, if I try to press button, the "Use keyguard switch to unlock screen and keys" message pops up, and nothing happens if I try to unlock it.

Levoh wrote:
Right new problem, its turned on but I have no contacts now. Was that meant to happen?
If you want to thank someone, just click on the blue star at the bottom of their post

N97 camera won't start(just a black screen)

My N97 camera won't start just a black screen this issue since the update to the new firmware

ooooooooops so sorry about this, here it goes and start with the first code.
With all these operations I recommend you TAKE OUT MEMORY CARD and DO A BACK UP OF YOUR STUFF!!!
1. *#7780# - Restore factory settings - resets all the settings to the default ( you will not lose any data)
Make sure you back up your data as you will lose all of it when you perform option 2 or 3 on this list. The default code for ALL operations listed here is 12345
2. *#7370# - Reformat your phone (out of the box, tho keep in mind that most newer nokia phones at least n series, e series and s60 based phones have udp - user data preservation so not ALL data may be lost. still it is a good idea to always do a back up of your stuff.)
3. This you perform as a last resort. Nothing else is working.If the phone is not showing any activity, proceed with hard formatting , turn off your phone, hold the following buttons while pressing the power button. (the default code is 12345)
hard reset - hold the following buttons *, 3 (number button) and talk/green key. turn on the phone and do not release those buttons until you see the Nokia boot up screen. once you feel the phone power up you can let go off the power button while still holding all three buttons ( for Nokia 5800XM - use the following buttons to do a hard reset, GREEN/RED/CAMERA keys pressed all at once on power up. this will only work on 5800's that have firmware version 20... and up. ) For Nokia N97 (unofficial version but works) is SHIFT /SPACE BAR / BACKSPACE while holding the power button. Again do not let go until you see the handshake screen.
If these codes are not working the only thing for you to do is contact your Nokia Care Center/Service for assistance.
You know what I love about you the most, the fact that you are not me ! In love with technology and all that it can offer. Join me in discovery....

Nokia XpressMusic 5130c-2 start up problem?

I have Nokia XpressMusic 5130c-2.When I try to switch the phone it starts,shows the "Nokia boot screen"and then the screen is white and Nokia won't start.Possibly the start up files are missing or it has a virus.I don't know.
Can anyone tell me how to format the phone or how to boot normally.Thankyou.

Adding to Farby's answer, also try booting it up without the Memory Card and the SIM Card. If it doesn't then it might need its firmware to be re-flashed. Just as farby said, you'll be needed to visit a Nokia Care Center in that case.

My 6151 won't start up anymore!!

my 6151 won't start up anymore.. i turned it off once and now it won't start up!! first it asks for my pin code and it goes along smoothly.. then it's on but the keypad's locked so i unlock it and it asks for my security code (since i put it on automatic keyguard with code) then when i enter my code, it freezes and either shuts down, restarts or freezes!!
can anyone please help me with this? i'm really lost on what to do.. please and thank you..

seems software only you need to get the unit updated.take it to nokia care centre
tongue is too confused on what to speak

My n900 won't start up

i got a problem...
a month ago, my n900 won't start up.
the battery getting flat, so i bought a new one.
but that doesn't help at all.
everytime i try to charge, or turn on, nothing happen. no changing on the light, and i didn't have nokia logo appear on it too if i press the turn on button.
i go to the nokia care, but they told me to replace the phone machine, and it cost me Rp. 1.900.000,- (if it's only Rp. 500.000,- i will pay, but the price is ridiculous)
could anybody in here can help me??
i want my n900 back to life without paying so much money.

@eijlk
Could only suggest you look at this resource:http://wiki.maemo.org/Updating_the_tablet_firmware with instructions "While holding the u key, connect the N900 to your computer via USB. Wait until you see a dim screen on your N900 with a Nokia logo in the middle of your screen with an USB icon in the top right corner" and specifically note"If the USB logo does not appear, and the device turns off - ensure the battery is charged by connecting to the wall charger for an hour and try again. Bear in mind that neither the wall charger nor the USB cable will charge the N900 battery if the N900 cannot boot the OS".
Unfortunately if device is dead to this procedure there is nothing left that you can do.
Happy to have helped forum with a Support Ratio = 42.5

SAP won't start after recabeling sap system

Hi, 
 
I have recently recabled my sap system (from wireless to wired) and now my sap instance won't start anymore. The weird thing is that nothing major was changed. When i read the logs from the work directory it seems it cannot load dbsdbslib.dll. I have updated to the latest version of the kernel and maxdb (kernel=7.00 patch 221, maxdb=7.6.06.07) and i made very sure i got the right kernel (NT AMD64). I also checked the environment settings for the <sid>adm user. The weird part is that it seems SAP cannot connect to the database, but the databse starts just fine and r3trans -d also returns no errors. Does anyone have an idea what could be wrong? 
 
Kind regards, 
Bas 
 
 
trc file: "dev_disp", trc level: 2, release: "700" 
 
 
command line arg 0: D:\usr\sap\IDE\DVEBMGS00\exe\disp+work.EXE 
command line arg 1: pf=D:\usr\sap\IDE\SYS\profile\IDE_DVEBMGS00_sap 
 
ERROR => DlLoadLib()==DLENOACCESS - LoadLibrary("D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll") 
Error 126 = "The specified module could not be found." [dlnt.c 255] 
sysno 00 
sid IDE 
systemid 562 (PC with Windows NT) 
relno 7000 
patchlevel 0 
patchno 221 
intno 20050900 
make: multithreaded, Unicode, 64 bit, optimized 
pid 3252 
 
kernel runs with dp version 243000(ext=110000) (@(#) DPLIB-INT-VERSION-243000-UC) 
length of sys_adm_ext is 576 bytes 
SWITCH TRC-HIDE on *** 
***LOG Q00=> DpSapEnvInit, DPStart (00 3252) [dpxxdisp.c 1287] 
ShmProtect( 5, 3 ) 
SigIInit: ok (whoami=1) 
Thread handle for mainthread created 
SigIRegisterRoutine: handler for signal 11 installed (SigISegv) 
Pipe created:
.\pipe\SAP3252 
SigIInit: Create Message Thread 
SigIRegisterExitRoutine: exithandler installed (DpHalt) 
SigIRegisterTerminateRoutine: terminatehandler installed (DpHalt) 
 shared lib "dw_xml.dll" version 221 successfully loaded 
 shared lib "dw_xtc.dll" version 221 successfully loaded 
 shared lib "dw_stl.dll" version 221 successfully loaded 
 shared lib "dw_gui.dll" version 221 successfully loaded 
 shared lib "dw_mdm.dll" version 221 successfully loaded 
dp_loc_queue_max_blk: 40000 
mshost: >sap< 
DpSetCancelStrat: set timeout 0 at level 0 
DpSetCancelStrat: set timeout 5 at level 1 
DpSetCancelStrat: set timeout -1 at level 2 
DpSetCancelStrat: set timeout -1 at level 3 
rdisp/softcancel_sequence : -> 0,5,-1 
softcancel_sequence: >0,5,-1< 
use internal message server connection to port 3900 
msserv: >3900< 
dp_bufreftime: 120 sec 
dp_btctime: 60 sec 
dp_autoabaptime: 300 sec 
dp_autothtime: 60 sec 
dp_autojavatime: 300 sec 
dp_vm_alarm_time: 100 msec 
dp_calldelayed_time: 60 sec 
dp_startup_time: 20 
dp_noptime: 0 sec 
dp_keepalive: 1200 sec 
dp_keepalive_timeout: 60 sec 
dp_ms_keepalive: 60 sec 
dp_ms_keepalive_timeout: 300 sec 
switch off dp-keep-alive for old temus 
dp_gui_auto_logout: 0 sec 
dp_spoolalrm: 60 sec 
dp_softcancel_timeout: 5 sec 
rdisp/wp_restart_interval : 300 sec 
DpISetTrcLog: trc logging active, max size = 20971520 bytes 
dp_rfc_check_active: 1 
dp_rfc_check_all_rfcs: 0 
dp_http_check: 1 
check_master_slave: 0 
NiHsLGetServNo: got service name 'sapdp00' from operating system 
NiIGetServNo: servicename 'sapdp00' = port 0C.80/3200 
NiHsLGetServNo: got service name 'sapgw00' from operating system 
NiIGetServNo: servicename 'sapgw00' = port 0C.E4/3300 
NiIMyHostName: hostname = 'sap' 
NiHsLGetNodeAddr: got hostname 'sap' from operating system 
NiIGetNodeAddr: hostname 'sap' = addr 192.168.2.250 
NiHsLGetHostName: found address 192.168.2.250 in cache 
NiIGetHostName: addr 192.168.2.250 = hostname 'sap' (fq) 
Mon Oct 26 16:14:29 2009 
NiHsLGetNodeAddr: hostname 'www.doesnotexist0190.qqq.nxst' not found by operating system 
WARNING => DpNetCheck: NiHostToAddr(www.doesnotexist0190.qqq.nxst) took 12 seconds 
Mon Oct 26 16:14:45 2009 
NiHsLGetHostName: address 1.0.0.1 not found by operating system 
WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 16 seconds 
NiHsLGetServNo: got service name 'http' from operating system 
NiIGetServNo: servicename 'http' = port 00.50/0080 
NiHsLGetServName: port 1F.90/8080 not found by operating system 
NiHsLGetServName: port FC.2B/64555 not found by operating system 
NiHsLGetServNo: service name 'sapdp9988' not found by operating system 
***LOG GZZ=> 2 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5521] 
SigIRegisterRoutine: handler for signal 16 installed (DpTrcOnOff) 
SigIRegisterRoutine: handler for signal 17 installed (DpTrcOnOff) 
SigIRegisterRoutine: alarm handler installed (DpSigAlrm) 
SigIRegisterRoutine: handler for signal 2 installed (DpSigInt) 
SigIRegisterRoutine: handler for signal 15 installed (DpSigInt) 
SigIRegisterRoutine: handler for signal 3 installed (DpSigQuit) 
MtxInit: 30000 0 0 
DpInitMtx: MtxInit o.k. 
PPID environment not found 
Thread handle for mainthread created 
SigIRegisterRoutine: handler for signal 19 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 18 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 24 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 0 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 21 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 22 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 23 installed (DpSigPrivDisp) 
SigIRegisterRoutine: handler for signal 25 installed (DpSigPrivDisp) 
 
 
trc file: "dev_w0", trc level: 2, release: "700" 
 
* 
ACTIVE TRACE LEVEL 2
ACTIVE TRACE COMPONENTS all, MJ
M
M command line arg 0: D:\usr\sap\IDE\DVEBMGS00\exe\disp+work.EXE
M command line arg 1: pf=D:\usr\sap\IDE\SYS\profile\IDE_DVEBMGS00_sap
M command line arg 2: wp_id=0
M
B create_con (con_name=R/3)
B Loading DB library 'D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll' ...
M *** ERROR => DlLoadLib()==DLENOACCESS - LoadLibrary("D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll")
Error 126 = "The specified module could not be found." [dlnt.c 255]
B *** ERROR => Couldn't load library 'D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll'
[dbcon.c 4905]
M sysno 00
M sid IDE
M systemid 562 (PC with Windows NT)
M relno 7000
M patchlevel 0
M patchno 221
M intno 20050900
M make: multithreaded, Unicode, 64 bit, optimized
M pid 4000
M
M kernel runs with dp version 243000(ext=110000) (@(#) DPLIB-INT-VERSION-243000-UC)
M length of sys_adm_ext is 576 bytes
M ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 4000) [dpxxdisp.c 1349]
M Mon Oct 26 16:14:47 2009
M SigIInit: ok (whoami=2)
M Thread handle for mainthread created
M SigIRegisterRoutine: handler for signal 11 installed (SigISegv)
M Pipe created:
.\pipe\SAP4000
M SigIInit: Create Message Thread
M SigIRegisterExitRoutine: exithandler installed (wp_halt)
M SigIRegisterTerminateRoutine: terminatehandler installed (wp_halt)
M SigIRegisterRoutine: handler for signal 16 installed (DpTrcOnOff)
M SigIRegisterRoutine: handler for signal 17 installed (DpTrcOnOff)
M SigIRegisterRoutine: alarm handler installed (DpSigAlrm)
M SigIRegisterRoutine: handler for signal 2 installed (DpSigInt)
M SigIRegisterRoutine: handler for signal 15 installed (DpSigInt)
M SigIRegisterRoutine: handler for signal 3 installed (DpSigQuit)
I MtxInit: 30000 0 0
M DpInitMtx: MtxInit o.k.
M WaitParent Thread 3252 start
M WaitParent Thread 3252 created
M Thread handle for mainthread created
M SigIRegisterRoutine: handler for signal 19 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 18 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 24 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 0 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 21 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 22 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 23 installed (DpSigPrivDisp)
M SigIRegisterRoutine: handler for signal 25 installed (DpSigPrivDisp)
 
 
trc file: "trans.log" 
 
 
4 ETW000 r3trans version 6.14 (release 700 - 12.06.09 - 15:20:00).
4 ETW000 unicode enabled version
4 ETW000 ===============================================
4 ETW000
4 ETW000 date&time : 21.10.2009 - 15:06:04
4 ETW000 control file: <no ctrlfile>
4 ETW000 R3trans was called as follows: r3trans -d
4 ETW000 trace at level 2 opened for a given file pointer
4 ETW000 [dev trc ,00000] Wed Oct 21 15:06:06 2009 0 0.000000
4 ETW000 [dev trc ,00000] db_con_init called 0 0.000000
4 ETW000 [dev trc ,00000] create_con (con_name=R/3) 0 0.000000
4 ETW000 [dev trc ,00000] Loading DB library 'dbsdbslib.dll' ... 0 0.000000
4 ETW000 [dev trc ,00000] DlLoadLib success: LoadLibrary("dbsdbslib.dll"), hdl 0, addr 0000000188C00000
4 ETW000 7580 0.007580
4 ETW000 [dev trc ,00000] using "D:\usr\sap\IDE\SYS\exe\uc\NTAMD64\dbsdbslib.dll" 16 0.007596
4 ETW000 [dev trc ,00000] Library 'dbsdbslib.dll' loaded 19 0.007615
4 ETW000 [dev trc ,00000] function DbSlExpFuns loaded from library dbsdbslib.dll 38 0.007653
4 ETW000 [dev trc ,00000] Version of 'dbsdbslib.dll' is "700.08", patchlevel (0.211) 307 0.007960
4 ETW000 [dev trc ,00000] function dsql_db_init loaded from library dbsdbslib.dll 26 0.007986
4 ETW000 [dev trc ,00000] function dbdd_exp_funs loaded from library dbsdbslib.dll 24 0.008010
4 ETW000 [dev trc ,00000] } DbSlSdbControl(rc=0) 46 0.008056
4 ETW000 [dev trc ,00000] { DbSlSdbControl(con_hdl=-1,command=39,arg_p=0000000000000000) 21 0.008077
4 ETW000 [dev trc ,00000] } DbSlSdbControl(rc=0) 15 0.008092
4 ETW000 [dev trc ,00000] { DbSlSdbControl(con_hdl=-1,command=10,arg_p=0000000003B4F920) 20 0.008112
4 ETW000 [dev trc ,00000] } DbSlSdbControl(rc=0) 15 0.008127
4 ETW000 [dev trc ,00000] New connection 0 created 17 0.008144
4 ETW000 [dev trc ,00000] 000: name = R/3, con_id = -000000001, state = DISCONNECTED, tx = NO , hc = NO , perm = YES,
4 ETW000 reco = NO , frco = NO , timeout = 000, con_max = 255, con_opt = 255, occ = NO
4 ETW000 50 0.008194
4 ETW000 [dev trc ,00000] { DbSlSdbControl(con_hdl=-1,command=10,arg_p=0000000001A01768) 31 0.008225
4 ETW000 [dev trc ,00000] } DbSlSdbControl(rc=0) 17 0.008242
4 ETW000 [dev trc ,00000] db_con_connect (con_name=R/3) 13 0.008255
4 ETW000 [dev trc ,00000] find_con_by_name found the following connection for reuse: 16 0.008271
4 ETW000 [dev trc ,00000] 000: name = R/3, con_id = 000000000, state = DISCONNECTED, tx = NO , hc = NO , perm = YES,
4 ETW000 reco = NO , frco = NO , timeout = 000, con_max = 255, con_opt = 255, occ = NO

Edited by: B. v. d. Lienden on Oct 26, 2009 5:18 PM

<div class=Section1>
Natalia,
 
To answer your questions:
1. Did you create the SAP ticket, where this problem is
reported?
I didn't report it to SAP because it is just an IDES test
system. I can easily do a reinstall, but i would like to know the cause and
solution to this problem.
 
2. Do you have dbsdbslib.dll at this location? What version?
Yes, i have the dbsdbslib.dll at location
D:\usr\sap\IDE\DVEBMGS00\exe and also D:\usr\sap\IDE\SYS\exe\uc\NTAMD64
Version is 7000.221.16.41497 (kernel 7.00 SP 221)
 
your requested output:
 
----

disp+work information
----

 
kernel releaseu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 700
 
kernel make variantu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 700_REL
 
compiled onu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 NT 5.2 3790 Service Pack 2 x86
MS VC++ 14.00
 
compiled foru00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 64 BIT
 
compilation modeu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 UNICODE
 
compile timeu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 Aug 23 2009 23:15:57
 
update level u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A00
 
patch numberu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 221
 
source idu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 0.221
 
 
----

supported environment
----

 
database (SAP, table SVERS)u00A0u00A0 700
u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 
operating system
Windows NT 5.0
Windows NT 5.1
Windows NT 5.2
Windows NT 6.0
ALLUSERSPROFILE=C:\Documents and Settings\All Users
APPDATA=C:\Documents and Settings\ideadm\Application Data
CLIENTNAME=BSF02
ClusterLog=C:\WINDOWS\Cluster\cluster.log
CommonProgramFiles=C:\Program Files\Common Files
CommonProgramFiles(x86)=C:\Program Files (x86)\Common Files
COMPUTERNAME=SAP
ComSpec=C:\WINDOWS\system32\cmd.exe
DBMS_TYPE=ada
DIR_LIBRARY=D:\usr\sap\IDE\SYS\exe\uc\NTAMD64
DIR_PROFILE=D:\usr\sap\IDE\SYS\profile
FP_NO_HOST_CHECK=NO
HOMEDRIVE=C:
HOMEPATH=\Documents and Settings\ideadm
JAVA_HOME=C:\j2sdk1.4.2_21-x64
LOGONSERVER=
SAP
NUMBER_OF_PROCESSORS=2
OS=Windows_NT
Path=D:\sapdb\programs\bin;D:\sapdb\programs\pgm;C:\j2sdk1.4.2_21-x64\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program
Files\Intel\DMIX;D:\usr\sap\IDE\SYS\exe\uc\NTAMD64
PATHEXT=.COM;.EXE;.BAT;.CMD;.VBS;.VBE;.JS;.JSE;.WSF;.WSH
PROCESSOR_ARCHITECTURE=AMD64
PROCESSOR_IDENTIFIER=EM64T Family 6 Model 15 Stepping 13,
GenuineIntel
PROCESSOR_LEVEL=6
PROCESSOR_REVISION=0f0d
ProgramFiles=C:\Program Files
ProgramFiles(x86)=C:\Program Files (x86)
PROMPT=$P$G
SAPEXE=D:\usr\sap\IDE\SYS\exe\uc\NTAMD64
SAPLOCALHOST=sap
SAPSYSTEMNAME=IDE
SESSIONNAME=RDP-Tcp#47
SystemDrive=C:
SystemRoot=C:\WINDOWS
TEMP=C:\WINDOWS\TEMP\2
TMP=C:\WINDOWS\TEMP\2
USERDOMAIN=SAP
USERNAME=ideadm
USERPROFILE=C:\Documents and Settings\ideadm
windir=C:\WINDOWS
 
----

disp+work information
----

 
kernel releaseu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 700
 
kernel make variantu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 700_REL
 
compiled onu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 NT 5.2 3790 Service Pack 2 x86
MS VC++ 14.00
 
compiled foru00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 64 BIT
 
compilation modeu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 UNICODE
 
compile timeu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 Aug 23 2009 23:15:57
 
update levelu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 0
 
patch numberu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 221
 
source idu00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 0.221
 
 
----

supported environment
----

 
database (SAP, table SVERS)u00A0u00A0 700
u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0u00A0 
operating system
Windows NT 5.0
Windows NT 5.1
Windows NT 5.2
Windows NT 6.0
 
 
</div>

Nokia C5 won't start

Similar Messages

Maybe you are looking for