Nokia C7 - Problem with VPN Connection over WLAN

Hello,
today I installed Nokia VPN Client 44.01(5) for Belle.
Before this update I used the following configuration: I set two SIP-profiles up and for each profile a own VPN-connection. One for connecting over radio and one for connecting over WLAN or hotspots.
So over all I had three kinds of connections or connection groups to choose: "Internet" with the radio and home wlan connections, "Intranet" for the VPN-connection over radio and "Intranet over WLAN" for VPN-connections over other WLANs.
The advantage of this configuration was that I could use the SIP-profile depending on my location and the phone had not to use the "standard" VPN-connection ("Intranet") over radio.
Now after the update I have the problem that I can't connect to my VPN over WLAN at all. Not with the SIP profile and not manually over the internet browser. There is always the notification "Connection Problem".
I tried also to put the "VPN over WLAN access point" from the "Intranet over WLAN"-group to the "Intranet"-group and gave it the first priority, but that doesn't helped too.
Does someone of you had or have the same kind of problem or otherwise has any clue about that?
Any help is very much appreciated!
Thank you in advance! I hope that I described my problem clearly.
Greetings
unsys

testing with the faceplate removed and into the master socket witha brand new filters result's below . I tried the quiet line test and it seems silent so no issues there. Can anyone see an issue, I've posted the noise results etc as well with the faceplate removed. (using a butter knife cause i'm just out of bed and tools are in the garage!)
0.7 Mbps
0 Mbps
1 Mbps Max Achievable Speed
Download speedachieved during the test was - 0.7 Mbps For your connection, the acceptable range of speeds is 0.2 Mbps-1 Mbps. Additional Information: Your DSL Connection Rate :1.06 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM) IP Profile for your line is - 0.75 Mbps
System Up Time 00:11:28
Port
Status
TxPkts
RxPkts
Collisions
Tx B/s
Rx B/s
Up Time
WAN
PPPoA
6657
9689
0
2806
19425
00:10:58
LAN
10M/100M
28652
22350
0
22356
5418
00:11:24
WLAN
11M/54M/300M
0
0
0
0
0
00:11:11
ADSL Link
Downstream
Upstream
Connection Speed
1056 kbps
448 kbps
Line Attenuation
49.0 db
27.0 db
Noise Margin
10.6 db
20.0 db

Similar Messages

Does anyone have problems with hotspot connections or WLAN since they have installed Lion?

Does anyone have problems with hotspot connections or WLAN since they have installed Lion?

Same problem for me: Since update to Lion my WLAN connection to my router (AVM fritz!box fon 7141) get's lost almost every time the computer is on idle for a couple of minutes. Deactivating and reactivating helps, but of course only until the problem occurs again.
BTW: I'm running Mac OS X Lion (10.7.3) on a iMac 27" 3.2 GHz i3 (mid 2010 model).
I'm really annoyed by this problem and looking forward for APPLES fix.

After upgrading on ios 6 i have problems with vpn connection..pls help if someone have the same problem

problem with vpn connection after upgrading on ios6.pls help

I've never been able to share FaceBook posts nor seen the option using the iOS FaceBook app regardless the FaceBook app and iOS version. I can Like and I can Comment, and if I select a link or video to view under iOS 6, I can use the Share option for the link or video, but not for a post.

RV320 problem with VPN connect (BUG)

forgive for bad English
Today I bought and I adjusted RV320, at once I saw some problems.
Firmware last
1. I adjusted two VPN tunnels between RV320 and two RV-082
also I saw what not one tunnel in Web panel not connect.
I many times pressed, the condition didn't change!
Having made Ping on 192.168.1.1 computers in a network 192.168.1.0 I saw answers:
it is simple a miracle or huge BUG.
2 The second BUG, VPN tunel No. 2 doesn't work in general as don't kick. And before there was RV-042G and RV-82 and everything was OK
From log:
2013-08-29, 21:47:28
VPN Log
[g2gips1]: cmd=down-client peer=78.31.177.145 peer_client=192.168.2.0/24 peer_client_net=192.168.2.0 peer_client_mask=255.255.255.0
2013-08-29, 21:47:28
VPN Log
ip route del 192.168.2.0/24 via 178.216.123.65 dev eth1 metric 35
2013-08-29, 21:47:28
VPN Log
iptables -t nat -D vpn -s 192.168.0.0/24 -d 192.168.2.0/24 -j ACCEPT
2013-08-29, 21:47:28
VPN Log
iptables -t nat -D vpn -s 192.168.2.0/24 -d 192.168.0.0/24 -j ACCEPT
2013-08-29, 21:47:28
VPN Log
iptables -t nat -D vpn_postrouting -s 192.168.0.0/24 -d 192.168.2.0/24 -j ACCEPT
2013-08-29, 21:47:28
VPN Log
iptables -t nat -D vpn_postrouting -o eth0 -s 192.168.2.0/24 -d 192.168.0.0/24 -j ACCEPT
2013-08-29, 21:47:37
VPN Log
[g2gips1] #14: [Tunnel Established] sent MR3, ISAKMP SA established
2013-08-29, 21:47:38
VPN Log
[g2gips1]: cmd=up-client peer=78.31.177.145 peer_client=192.168.2.0/24 peer_client_net=192.168.2.0 peer_client_mask=255.255.255.0
2013-08-29, 21:47:38
VPN Log
ip route add 192.168.2.0/24 via 178.216.123.65 dev eth1 metric 35
2013-08-29, 21:47:38
VPN Log
iptables -t nat -I vpn -s 192.168.0.0/24 -d 192.168.2.0/24 -j ACCEPT
2013-08-29, 21:47:38
VPN Log
iptables -t nat -I vpn -s 192.168.2.0/24 -d 192.168.0.0/24 -j ACCEPT
2013-08-29, 21:47:38
VPN Log
iptables -t nat -I vpn_postrouting -s 192.168.0.0/24 -d 192.168.2.0/24 -j ACCEPT
2013-08-29, 21:47:38
VPN Log
iptables -t nat -I vpn_postrouting -o eth0 -s 192.168.2.0/24 -d 192.168.0.0/24 -j ACCEPT
2013-08-29, 21:47:38
VPN Log
[g2gips1] #15: [Tunnel Established] IPsec SA established {ESP=>0x102b2557 < 0xc23b7d0f}
What problem i'm undersdund.
3 The third BUG, adding or changing VPN tunnels, against for a second there is a form for addition of the new tunnel, why it? ? ?

A little later...
I solved reset all settings to default and to adjust from scratch, all work.
What is done? I don't understand.

Nokia 8800 Problem with bluetooth connection !

Ok i read alot of the topics here but i try everything and it just dont work ! It gives me some **bleep** that saz Cannot Authenicate the phone wich i dunno why ! I TRY EVERYTHING ! i have the latest PC SUITE and BlueSoleil but i still dont know what to do and why it doesnt workks (
HELP ME PLEASE ANYONE HEEEELLLPPP MEEE !!!

Go to PC Suite get connected wizard, select Bluetooth, then select "unpair". Once unpair is done, boot PC and phone, then put Bluetooth in phone on again and use get connected wizard to "repair" the Suite and phone.

Problem with IP phone over VPN

         |   UC520   | ------------------------ |     861     |
                 |                                                  |
              LAN                                             LAN
Scenario:
UC520 box is at HQ and serving as a EZVPN server and 861 at branch as a EZVPN client. There is no problem with VPN i can communicate with HQ network. My ip phone get registered but facing these problems.
1) Dialling out and in OK
2) Connects OK after picking up
3) NO sound either way
4) Cannot end call from this side. End call button does not work
5) When other end hangs up - message "UCM down, features disabled". Then phone registers again.
Identical symptoms for both softphone and 7941.

This document provides a sample configuration for Quality of Service (QoS) for Voice over IP (VoIP) traffic on VPN tunnels that terminate on the PIX/ASA Security Appliances.
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008080dfa7.shtml

Number of connections over WLAN bridge?

I have a network that has been working flawlessly for many years but when I recently added a printer I ran into some problems. The printer is connected to a switch that is connected to an Airport Express that is connected over WLAN to an Airport Extreme. My problem is that I can only connect four devices to the switch. If I connect a fifth device it does not get an IP adress until I disconnect one of the other four devices. Please see the attached overview of the network. Red dotted lines represent wireless connections.
Any ideas about what causes this behavior is appreciated. Thank you.

on a jetpack or mi-fi 5 GB is nothing. Streaming Netflix can use 2.3 GB an HOUR. Even streaming YouTube in HD can use 1 or 2 GB per hour. I'm not sure why people think 5 GB is a lot for a regular internet connection. it's not. That why people should be using cable or DSL or fiber for internet

Problem with JCo Connection Pool

Hi,
I have a problem with using an RFC Model in my WebApplication. So sometimes the access to the function block works, and sometimes it doesn't work. Now I know, that there is a problem with the connection pool. Look at this message:
com.sap.mw.jco.JCO$Exception: (106) JCO_ERROR_RESOURCE: Connection pool WD_X24_MODELDATA_DEST_CPIC_REKTO_DE_useDefinedUser is exhausted. The current pool size limit (max connections) is 10 connections.
So it looks like a problem with closing the JCo Connections after using. Do know where the problem is? Because I'm using many other function blocks with no problems.

Hello,
You need to increase the pool size via Visual Administrator.
Server 0 -> Services -> JCO RFC Connections.
Change the pool size from there. I believe a restart is in order.
Regards,
Jan

Problems with ipod connection.

Problems with ipod connection.
I have problems to connect my ipod to computer windows 7.
When I connect I get the following error:
"We encountered an ipod, but could not be identified correctly. Disconnect and reconnect the ipod and try again."
And it recognizes the ipod when trying to go play music or videos make me the following error:
"Error while trying to copy on disk. The device is not connected."
I've uninstalled all apple applications and re-installing, as I formatted the ipod and continues to set the same error.
What else can I do?

Hello,
While your symptoms don't exactly match the descriotion, this article may be usefull in discovering if there is a setting on your computer that is causing this to happen.
iPod not recognized in 'My Computer' and in iTunes for Windows
http://support.apple.com/kb/ts1369
-Griff W.

Problems with File Transfers Over Firewire 800

Problems with File Transfers Over Firewire 800.
Over the past month, I have had problems when transfering files from my harddrive, over Firewire 800 to a portable drive. I usually transfer very large files (20gb or more) to the portable drives for moving files around. When I drag a file over to copy onto a drive, the transfer starts normally. If I drag more files to copy over, the computer screen goes darker and a large icon comes up that looks like a power button icon. It tells me to restart, so I have to do a hard shut down on my G5. Weird. I also get the dark screen of death sometimes when I am transfering those large files and open another application to do some work while it's copying. It's killing me. I am having to sit here and wait for the transfer to finish before I can do anything.
Any thoughts...
Dual 2.7 GHz PowerPC G5
Mac OSX 10.4.3
Dual 2.7 GHz PowerPC G5 Mac OS X (10.4.3)

Have you run the Apple Hardware Test? Sounds like it could be a RAM problem.

Every time I try and update my iphone 4 to ios 7.1 in iTunes 11.1.5 it says "connection reset" even when there is no problem with my connection

I have an iPhone 4. I use iTunes 11.1.5 on my Mac. I am trying to update to ios 7.1 through iTunes, but every time I do that, I get a "connection reset" error, even when I know there has been no problem with my connection.
The exact error message is as follows:
"There was a problem downloading the software for the iPhone "Anne's iPhone". The network connection was reset.
Make sure your network settings are correct and your network connection is active, or try again later."
I have checked several times. There is no problem with the connection, and I have tried to download the software several times today.
Any help you can give me would be appreciated.

Just managed to successfully download the update, having retried five or six times. I did unplug my phone while the download was taking place (had asked iTunes to download only, not to update) -- suspect this had no bearing on it whatsoever, and that persistence is the only way here.

Exchange Server 2010 SP3 - Rollup 8 - Issue - Problems with client connections - MS Outlook 2013

Exchange Server 2010 SP3 - Rollup 8 - Issue - Problems with client connections - MS Outlook 2013
Detected Problems:
- Access denied for attached mailbox (department mailbox)
- Access denied for delete or move messages on own mailbox
- Can't send new messages with error (Error: [0x80004005-00000000-00000000])
Solution:
- Rollback to Exchange 2010 SP3 - Rollup 7
- You can rollback to Exchange 2010 SP3 - RollUp 7 in 30 min
Algunos de los destinatarios no recibieron su mensaje.
Asunto: Hola
Enviado el: 11/12/2014 8:35
No se puede localizar a los destinatarios siguientes:
'[email protected]' en 11/12/2014 8:35
Este mensaje no se pudo enviar. Inténtelo de nuevo más tarde, o póngase en contacto con el administrador de red.
Error: [0x80004005-00000000-00000000].

See the following forum thread:
https://social.technet.microsoft.com/Forums/en-US/1be9b816-b0ab-40ea-a43a-446239f8eae3/outlook-client-issues-following-exchange-2010-rollup-8

My station is listed on Itunes Radio stations, but there's a problem with the connection. Does any body help us regarding this issue? The station name is KRAL FM under the Top 40 / Pop category

My station is listed on Itunes Radio stations, but there's a problem with the connection. Does any body help us regarding this issue? The station name is KRAL FM under the Top 40 / Pop category

My station is listed on Itunes Radio stations, but there's a problem with the connection. Does any body help us regarding this issue? The station name is KRAL FM under the Top 40 / Pop category

I can't make a purchase with iTunes because it says there's a problem with the connection. How do I fix this?

I can't make a purchase with iTunes because it says there's a problem with the connection. How do I fix this?

Morning Gjakleinmark,
Thanks for using Apple Support Communities.
For more information on this, take a look at this article:
Can't connect to the iTunes Store
http://support.apple.com/kb/ts1368
Best of luck,
Mario

Nokia 6303c Problem with camera, says camera on st...

nokia 6303c Problem with camera, says camera on standby solution, any body got any solutions
many thanks in advance

try to free up some of your phones memory delete unwanted files ,delete text ,images etc or move to memo card
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Nokia C7 - Problem with VPN Connection over WLAN

Similar Messages

Maybe you are looking for