Nokia CS-15: Deaktivating voice channel

Hello,
I searched the whole internet without find a solution, so I am now here...
Last week I bought the Nokia CS-15 Internet Stick in order to use it for mobile connections with my Vodafone UltraCard (it's a MultiSim). Unfortunately the CS-15 blocks the data AND voice channel while being connected. Because of this I can't receive telephone calls on my mobile while using the CS-15.
For other devices I found several AT commands to deactivate the voice channel, but no resolution for the CS-15. The known AT commands did not work on the Nokia device.
Have someone of you an idea to fix this problem?
Why does the stick block the voice channel?
Thanks a lot
Thomas

The SIP Media Inactivity Timer feature enables Cisco gateways to monitor and disconnect VoIP calls if no Real-Time Control Protocol (RTCP) packets are received within a configurable time period.
When RTCP reports are not received by a Cisco gateway, the SIP Media Inactivity Timer feature releases the hung session and its network resources in an orderly manner. These network resources include the gateway digital signal processor (DSP) and time-division multiplexing (TDM) channel resources that are utilized by the hung sessions. Because call signaling is sent to tear down the call, any stateful SIP proxies involved in the call are also notified to clear the state that they have associated with the hung session. The call is also cleared back through the TDM port so that any attached TDM switching equipment also clears its resources.
http://www.cisco.com/en/US/products/ps6441/prod_troubleshooting_guide09186a00801fa207.html#wp2077496

Similar Messages

Fax outdial retries consume all voice channels on SIP 484 error (Cisco 2911)

I've been seeing a nasty fax/VoIP problem on a 2911, running IOS 15.0(1r)M12. Any suggestions would be welcome.
I have a 2911 which is set up to do T.37 offramp fax delivery (SMTP message is sent to 2911, which places a VoIP call over SIP/RTP/T.38 to deliver the fax). The mainline case is set up, and working correctly - faxes are delivered without issue. If a destination address is selected such that the VoIP switch returns a SIP 484 error, then everything fails in a spectacular fashion:
The outdial is immediately retried, placing another SIP INVITE to the switch, with the same destination address, which obviously also gets the same 484 response.
Each time the outdial takes place, it consumes voice channels on the DSP, which are not released on receipt of the 484.
When there are no free voice channels, a no circuit (0x22) error is returned, and all the voice channels are finally released.
The MTA that submitted the SMTP message retries every minute (it doesn't get a permanent failure report when the 2911 fails to place the call)
This leads to a situation where no fax calls can be placed, as all the voice channels are being used up by retrying this call that can never succeed.
Some other relevant information:
The VoIP switch does not return a 484 immediately. First it sends a SIP 183, and plays early media (an announcement about how the call isn't allowed).
It takes 8 seconds before the 484 is returned. The 2911 sends a new SIP INVITE every 8 seconds (as soon as it gets a 484 for the previous attempt).
The "sip-ua" statistics show that the INVITE retry counter is not being incremented (i.e. this is not a retry at the scope of the SIP stack).
The T1 cable is looped-back to the 2911, so that the complete path for fax delivery looks like this:
MTA ---SMTP---> 2911 ---T1---> 2911 ---SIP---> VoIP switch
If I set "mta receive generate permanent-error", then I still see this retry behaviour, with all the voice channels being consumed. Once that has happened (after about 3 minutes) the MTA does get the error response, and no longer retries every minute after that (although this setting has other negative effects that I'd like to avoid).
Does anyone have any idea how I can get the 2911 to return a permanent failure to the MTA after just a single outdial has failed with a SIP 484?
Here is the dial-peer config:
dial-peer voice 1 voip
translation-profile incoming IncomingVoip
incoming called-number .
voice-class codec 1
dtmf-relay rtp-nte
fax protocol t38 version 0 ls-redundancy 3 hs-redundancy 0 fallback pass-through g711ulaw
no vad
dial-peer voice 2 pots
destination-pattern ^0005
port 1/1:23
forward-digits all
dial-peer voice 3 pots
translation-profile incoming IncomingPRI_1_0
service onramp-app
incoming called-number ^0005
direct-inward-dial
port 1/0:23
dial-peer voice 4 mmoip
service fax_on_vfc_onramp_app out-bound
destination-pattern .
information-type fax
session target mailto:$m$@<DOMAIN NAME>
image encoding MH
dial-peer voice 101 mmoip
translation-profile incoming IncomingMMoIP
service offramp-app
information-type fax
incoming called-number .
dial-peer voice 102 pots
destination-pattern .
port 1/0:23
forward-digits all
dial-peer voice 103 pots
translation-profile incoming IncomingPRI_1_1
incoming called-number ^0007
direct-inward-dial
port 1/1:23
dial-peer voice 104 voip
translation-profile outgoing OutgoingVoip
destination-pattern ^0008
session protocol sipv2
session target ipv4:<VoIP SWITCH IP ADDRESS>
voice-class codec 1
dtmf-relay rtp-nte
fax protocol t38 version 0 ls-redundancy 3 hs-redundancy 0 fallback pass-through g711ulaw
no vad

Hi Ellad.
Why don't try to use the 2811 as a SIP signalling proxy only?
In this way the media (RTP or T.38) will be handled only from the two MERA SoftSwitch.
To do this you must enable CUBE on your 2811 and use these special commands:
voice service voip
     media flow-around
     allow-connections sip to sip
     signaling forward unconditional
     sip
       rel1xx disable
       header-passing
       midcall-signaling passthru
       pass-thru headers unsupp
       pass-thru content unsupp
       pass-thru content sdp
I don't remember if we have already try this solution.
Regards.

ANy MIB to poll for no. of active voice channel on 2611 with T1 Module

Hi ppl,
I have a 2611 router with a T1 voice card (NM-HDV-1T1-24) as a voice gateway in my office. IOS version c2600-is-mz.122-11.T2.bin has been loaded and running.
I have tried to poll the mib oject "cvActiveCallConnectionID " under the Cisco-Voice-Dial-Control MIB for no. of active voice channel. I use solarwinds engineering edition 2002 to poll this device. It shows an error said that the mib is not supported in this version of IOS. We are running VoFR in our existing environment
I have checked in the Cisco MIB webpage --
ftp://ftp.cisco.com/pub/mibs/supportlists/c2611/c2611-supportlist.html
-- that the IOS is supported in version 11.3!!! Is it only support in 11.3 or any later version?
If not, any possible mib or workaround can solve my problem.
Regards,
Sam

The information is in the mib object cvCallActiveTable. There is no frame-relay equivalent to the VoIP object. The only frame-relay specific SNMP info you can verify is CISCO-VOICE-FR-DIAL-CONTROL-MIB

Strange problem with Nokia E5-00 Outgoing Voice

Nokia has swapped my E5 after the old one was not switching on, now the new problem has started I can receive incoming and make outgoing but my outgoing voice won’t be heard on other end. This happens only for few hours in the morning by the evening it the phone works fine.
I faced the problem in the morning then gone to Nokia service centre there it works fine… it happens every day every morning then by the evening
Please suggest a solution

The problem is more likely with your service provider rather than with the phone. Try using the SIM of a different network in the morning or try using the current SIM with a different phone that's known to be working fine otherwise. Once you determine the cause of the problem is the network, speak to them for assistance.

Adding voice channels to a trunkgroup

I have this:
controller T1 2/0
framing esf
linecode b8zs
pri-group timeslots 1-24
description Connection to Switch T1 2
controller T1 2/1
framing esf
linecode b8zs
pri-group timeslots 1-24
description Conecction to the switch T1 18
It happens that sometimes the T1 2/0 is full so I would like to direct the overflow traffic to the T1 2/1.
I was thinking on using something like:
controller T1 2/0
framing esf
linecode b8zs
cablelength short 133
pri-group timeslots 1-24
trunk-group alpha timeslots 1-23
description Connection to Switch T1 2
controller T1 2/1
framing esf
linecode b8zs
cablelength short 133
pri-group timeslots 1-24
trunk-group alpha tiemslots 1-6
trunk group beta timeslots 7-23
description Conecction to the switch T1 18
And at the dial-peers use the trunkgroup alpha in the one I like 29 channels and trunkgroup beta in the one that will remain with 16 channels.
Will this work?
Any comment will be apperciated.
Regards

This is my recommendation.
Step 1) Create your Keynote presentation.
Step 2) Record your speaking part (separately) with an audio recording program.
I recommend Audacity. It's a great free application. You can download Audacity from www.sorceforge.com among other places. You'll also want to get the Audacity LIB file that is needed to export your audio recording to .mp3.
3) From the Keynote Inspector, under the Document tab, go to the audio section and add your new voice recording file to the Soundtrack.
4) From Keynote, go to File, Record Slideshow.
While the audio plays, click through your slides. This is getting the slide change time down.
5) From Keynote, go to File, Export. Make sure to have the following settings:
Playback Uses: Recorded Timing
Include audio (sound files, movie audio): NOT SELECTED
Include the slideshow soundtrack: NOT SELECTED
Include the slideshow recording: SELECTED!!!
Click next and your Keynote presentation should export to a .mov file (keep in mind, this .mov file has no audio. we'll take care of that in the last steps).
6)Open the new .mov Keynote presentation in Quicktime Pro.
7) Open the original .mp3 sound file in Quicktime Pro.
8) Select All of the .mp3 file and then click CTRL + C to copy it.
9) Go back to the .mov Keynote file and Select All. Then go up to Edit > Add to Movie.
This adds your sound and movie file together.
10) Finally click on File > Save As. Select, Save As A Self-Contained Movie and you're done.
I Hope This Helps!

How to verify voice channels on voice gateway

Hello,
I am in the testing phase of deploying a 2921 voice gateway with 2 PRIs. After connecting the T1s, how do I verify if all the channels are up and ready for use? Also, how do I verify if clocking on the T1 interfaces are configured correctly?
This 2921 is a replacement for a 2811 currently being used. When I login to the 2811 via SSH, I see this:
560240: Aug 13 20:37:24.368: %ISDN-6-CONNECT: Interface Serial0/2/0:3 is now connected to 3854143418 N/A
560241: Aug 13 20:37:24.368: %ISDN-6-CONNECT: Interface Serial0/2/0:3 is now connected to 3854143418 N/A
560242: Aug 13 20:37:24.544: %ISDN-6-CONNECT: Interface Serial0/2/0:5 is now connected to 7753428028 N/A
560243: Aug 13 20:37:24.544: %ISDN-6-CONNECT: Interface Serial0/2/0:5 is now connected to 7753428028 N/A
560244: Aug 13 20:37:27.128: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to 7753296300 N/A
560245: Aug 13 20:37:27.128: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to 7753296300 N/A
560246: Aug 13 20:37:27.128: %ISDN-6-CONNECT: Interface Serial0/2/0:22 is now connected to 3296300 N/A
560247: Aug 13 20:37:27.128: %ISDN-6-CONNECT: Interface Serial0/2/0:22 is now connected to 3296300 N/A
560248: Aug 13 20:37:27.652: %ISDN-6-CONNECT: Interface Serial0/2/0:20 is now connected to 3525101 N/A
560249: Aug 13 20:37:27.652: %ISDN-6-CONNECT: Interface Serial0/2/0:20 is now connected to 3525101 N/A
560250: Aug 13 20:37:30.320: %ISDN-6-CONNECT: Interface Serial0/2/1:22 is now connected to 3525101 N/A
560251: Aug 13 20:37:30.320: %ISDN-6-CONNECT: Interface Serial0/2/1:22 is now connected to 3525101 N/A
How do I do that with the 2921 in an SSH session? I've enabled "logging monitor" and "term mon" but I still can't see messages like that.
I thank you very much for your time.

Hello,
To check clocking you can use the "show network-clock" command. For example:
SiteA-RTR#show network-clock
Network Clock Configuration
Priority Clock Source Clock State Clock Type
1 T1 0/0/0 GOOD T1
10 Backplane GOOD PLL
Current Primary Clock Source
Priority Clock Source Clock State Clock Type
1 T1 0/0/0 GOOD T1
The above is an example of a "good" configuration, assuming that T1 0/0/0 is the controller terminating the line from your carrier. In your case, it would be T1 0/2/0 or 0/2/1. You can also look at "show controller t1 [interface]" (e.g. show controller t1 0/2/0) and pay particular attention to "Line Code Violations", "Slip Secs", and "Errored Secs" counters. Note that the "Clock Source Line" status in the "show controller t1" command is not enough to verify you have proper clocking.
Example of a "bad" clock scenario:
SiteA-RTR(config-voiceport)#do sh controller t1 0/0/0
T1 0/0/0 is up.
Applique type is Channelized T1
Cablelength is long 0db
No alarms detected.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info Firmware: 20080918, FPGA: 13, spm_count = 0
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (483 seconds elapsed):
3 Line Code Violations, 4 Path Code Violations
207 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
206 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 109 Unavail Secs
To make sure the clock is set correctly, look at the "network-clock-participate" and the "network-clock-select" commands.
For the ISDN status information, you can use "show isdn status". For example:
SiteA-RTR(config)#do sh isdn stat
Global ISDN Switchtype = primary-ni
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply
ISDN Serial0/0/0:23 interface
dsl 0, interface ISDN Switchtype = primary-ni
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x800000FF
Number of L2 Discards = 0, L2 Session ID = 15
*Note: The above is output from a gateway provisioned to use MGCP.
For all gateways, just make sure that Layer 1 is "ACTIVE" and that Layer 2 has "MULTIPLE_FRAME_ESTABLISHED".
You can also use the "show isdn service" command to look at status for individual B-channels.
SiteA-Rtr#sh isdn service
PRI Channel Statistics:
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not appl
ISDN Se0/0/0:23, Channel [1-24]
Configured Isdn Interface (dsl) 0
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2
Use the "Channel State" and "Service State" to verify things are what you expect.
HTH.
-Bill (@ucguerrilla)
http://ucguerrilla.com

Obtaining the number of voice channels with SNMP

Is it possible to get the number of channels in use across a number of voice gateway via SNMP from CallManager?
In RTMT I view the see "MGCP PRI: Channel Active" statistic within Gateway Activity. This is a figure for the whole CCM cluster. I've looked at the CISCO-CCM-MIB but cannot find a reference to this particular value. Can this value be retrieved through the use of SNMP?

it is possible to retrieve the number of channels in use from SNMP.
use PERFMON >
PerformanceObject = MGCP Gateways
Counter = PRIChannelsActive
Instances = All (or which ever you need to view)
this information is also available in RTMT as well as most other SNMP packages such as NetIQ

Nokia N96, Bluetooth, and voice-dialing....

Hi,
I upgraded from my N80 to an N96 and, being a rep and frequently on the road, Im finding the voice-dialing to be a real PITA.
The N80 would work just about anywhere. Car, street, pub, shops, wherever, it understood who I wanted to call. Not perfect, but close.
The N96 doesnt even PRETEND to understand me, throwing up any name at random it seems.
Worse, it is all very haphazard to use.
You press the top right function button and hold it down. On the N96, you could hold it for a very long time before it responds. Since the processor in this phone is way underpowered, it a second or two before your hear the Speak Now confirmatory beeps.
Couple that with the problem that many Bluetooth headsets power-down momentarily, it means that when youre driving along in the car and hold the button down on your BT headset, you dont actually hear the beeps. So you have to look down at the phone to see what its doing. While driving, this can be dangerous.
Now, because you ARE driving, the N96 is not likely to understand you anyway.
Nokia!! You need to go back to the drawing board here!!
1) Fix the voice-dial activation - pressing the top-right button for two seconds is plenty.
2) Play the bleeps WHEN the Speak Now screen comes up, not before! My N96 can take anywhere between 1 and 5 seconds between the bleeps and the Speak Now screen appearing!
3) Play the bleeps a bit longer when the Bluetooth headset is activated. Most Bluetooth headsets take a second or two to wake up - the sound is over by then and you miss it.
4) Go back to the N80 and read the code for what you did in that phone. It worked fine there!
Ian Nicholson
Poor Sod/N96 Owner
Nokia: Connecting People... with iPhones.

Still here is no improvement with voice dialing with ver 12 soft and training sessions to n96.
It handles well with some names, but not with most. My old N95 did it much better from beginning (no training need!).
And extra case is with bluetooth HF - I stopped for waiting now for this stupid "beep" that is coming or before or after or in the middle the time, when voice detection screen is there. Now I just try to say the name about 2 sec after pressing BT button.
So, I hope some good Nokia engineer happens to read those voice dialing posts and in soft ver 13 we get better dialing (and finally somehow faster phone). Or do we, all who don't like extra slow processor should go in same day to service/operator and give in protest about the speed..

Nokia 6301 BT headset voice activated dialling

Hi
I have just upgraded to a 6301 and have a Jabra BT250V headset. Previously I had a Nokia 6230i and by using the button on the headset I could make the phone give me the "Speak now" prompt to do voice dialing and end the call - all from the headset. With the new phone I can pair it but no control of the phone. Phone guide says press and hold right selection or down volume key to kick of the "Speak now". I'd like to control it from the headset. According to the Jabra website the BT250V is fully compatible with this phone.
Any ideas on settings on the phone to get this to work or a Bluetooth headset that does do this?
Thanks
Mart

There are chances that the headset is not fully compatible with the 6301 phone.
Though its shown on the Jabra website,have they tested it?
Compatibility must have yielded mixed results.
Incompatibility has been confirmed by test or other evidence. Initially, compatibility may have been considered possible.
Test has yielded critical failures. Incompatibility not confirmed yet (possibly: fixes/retesting expected)
Test has yielded critical failures. Incompatibility not confirmed yet (possibly: fixes/retesting expected)

Hardware requirement for voice/fax channel from T1?

Hi all,
I don't know if this is the right forum, but I am looking for validation on my interpretation of hardware requirements.
The scenario:
I currently have a T1 coming in to the facility and terminating into a vendor-supplied Adtran box which splits off one of the channels from the T1 for voice/fax use (the Adtran has a centronics-style connector going to a 66 block)
I am also in the process of ordering ADSL service to supplement the bandwidth for non-business usage.
Rather than end up with a solution involving an adtran, ADSL modem, and router or two... I want to combine all services into a 1751 chassis. My only concern / confusion is how to 'split' off the single voice channel from the T1. There is a phone # associated with the voice channel.
I believe that I will need the router, a multiflex T1 WIC (VWIC-1MFT-T1), ADSL wic (WIC-1ADSL-DG), and an FXS card such as the VIC-2FXS
Am I close here, or completely off base? Any input or suggestions would be appreciated.
Thanks!
-P

Paolo,
Thanks for the reply - I guess I'm just trying to figure out if the way I described is the 'concept' and correct WIC/VWIC combination of how to get an analog dialtone from a T1 channel while leaving the rest for data.
I know there are probably many more benefits to going with a more modern router, but this is for personal use (the T1 is tied to a business account, but hosted in my house and maintained by me) and I can't really get an ISR in my price range - 1751s, on the other hand, are easy to come by and affordable - I just want to ensure I can have a single line available for Fax
Thanks!
-P

How to add voice navigation in nokia 6110 navigato...

Hello i have a nokia 6110n and the voice navigation is only in english and i want to add in portuguese is it possible?
How please?
Tanks

I'm running Ovi 3.01 on a different phone (5800) so this may or may not help you. But on my phone, I can go to
Options -> Tools -> Settings -> Navigation -> Voice guidance
and make my selection, and the phone will download whatever is needed automatically, assuming you are already connected to the internet.
-Yongtao
Message Edited by yongtao_you on 15-Dec-2009 05:07 PM

Nokia 7100 Voice activation

I have just bought the Nokia 7100 Supernova - I wanted to stay with Nokia because of the voice activation and having a hands free kit in the car. Firstly I can't figure out how to set up voice activation & secondly, although I have twinned the phone with my active device in the car & they look connected, when I try & make or receive a call nothing happens - usually the radio cuts out & the voice comes through the speakers & this isn't happening - help!!!!!

1. In the standby mode, press and hold the right selection key or the volume down key.
A short tone sounds, and Speak now is displayed.
2. Speak the name of the contact you want to dial. If the voice recognition is successful,
a list with matches is shown. The phone plays the voice command of the first match
on the list. If it is not the correct command, scroll to another entry.

Connection plar on voice T-1 channels?

Hi,
can you do connection plar on t-1 voice channels.
we have a scenerio where we need to be able to pass calls from unique T-1 voice channels to unique extensions in a remote site.
thanks in advance

thanks, that makes sense!
so it should look something like this?
Controller t1 1/0
ds0-group 0 timeslots 1 type fxo-loopstart
ds0-group 1 timeslots 2 type fxo-loopstart
ds0-group 2 timeslots 3 type fxo-loopstart
ds0-group 23 timeslots 24 type fxo-loopstart
voice-port 1/0:0
connection plar 100
voice-port 1/0:1
connection plar 101
dial-peer voice 100 pots
destination-pattern 100
port 1/0:0
dial-peer voice 101 pots
destination-pattern 101
port 1/0:1
Thanks

E71 and Nokia Maps

I am trying to compare the 2 Satnav systems on my phone......
Vodafone SatNav gives me 18 month subscription with voice navigation
Nokia Maps giives me 3 month subscription withOUT voice nav. (I am only a week or so into the 3 months)
If I go to download voice it prompts me to pay but doesnt say how much ??
Isnt there voice trial ubscription ??

The next time you try, when you get the prompt to pay, just click on the update option. All Nokia Subscriptions come with voice and so should yours. ALl you need to do is to update your license details by clicking on the update option.
You have to be online to allow Nokia Maps to access the license server when doing this.
Message Edited by cjlim on 24-Jan-2009 03:56 PM

Nokia Trailers 1.3.31 - Network Problem, N8 Belle

Hi,
Updated to Nokia Trailers 1.3.31 a couple of days ago and as soon as I did the app no longer starts. Instead, I get "Network problem" and then it shuts down.
I've uninstalled and reinstalled the app to no avail.
Network is fine, wifi and 3g, all other apps (mail, fb, twitter, maps, foursquare, store, cutebox, etc) are working, so what's up with Trailers?
Attachments:
Scr000032.jpg ‏54 KB

Fixed the problem with Trailers on my N8 last night by doing a format, hard reset and firmware reinstall via Nokia Software Updater.
This also fixed the problem I was having with Google Maps, Nokia Drop and Maps voice guidance via bluetooth to the car stereo.
Happy days!

Nokia CS-15: Deaktivating voice channel

Similar Messages

Maybe you are looking for