Nokia E51 WLAN transfer rates

Hello,
I have e51 phone, I was trying to connect to the university Wireless, but E51 couldn't connect.
I try it with E65 and its working..
I asked the IT and they told to make sure from the Nokia E51 WLAN transfer rates..
Because if it was 1 or 2 MB it won't work.
is there anyone has an idea about it???
thanxx

Many thanks! Fixed it for me I guess there is a problem with the DHCP client when using WPAx?

Similar Messages

NOKIA E51 WLAN VISTA SHARED

HI,
has anyone tried setting up a wlan between a nokia E51 and
a vista (home network) using a wifi lan port?
thanx for your support
carlito

Many thanks! Fixed it for me I guess there is a problem with the DHCP client when using WPAx?

E51 WLAN Setup Issues

Hi,
I know this has been discussed before, but after searching and trialing I've got nowhere.
Just got my E51 and trying to connect to my home wireless network. Appears to connect fine, try to start browsing, no data is transferred and eventually times out...
I've tried wizard setup and manual setup - both give the same results.
Router (Netgear WGR614) setup:
WPA-PSK security
SSID visible
Phone set-up
Network status Public
WLAN mode Infastructure
WLAN security mode WPA/WPA2
WPA2 security mode off
Think that's about it. Any solutions as to what causes this? I fear it's a firewall setting as allows connection but no data transfer. I disabled the SPI firewall on the router and that didn't help.
Thanks for any help!

I don't know what exactly caused the problem, which consisted of not being able to connect my Nokia E51 to the WLAN Router but if the security settings were disabled. Whenever I tried to enable the security settings with WEP/WPA on my WLAN router, although the access point was duly detected, and apparently flawlessly listed, it would no longer be available when actually trying to connect, as it would return the error message "WLAN not found".
After reading a few things about security issues, (http://www.wi-fiplanet.com/tutorials/article.php/3672711, http://www.practicallynetworked.com/security/041207wpa_psk.htm) I decided that there is no way I could accept to connect to WLAN without security encryption.
By trial and error I managed to enable the security settings on the WLAN router AND successfully connect with Nokia E51 only after I did this:
1) Changed the SSID to some very exotic new name, completely different from the previous default name (supplied by the manufacturer). I noticed that the default SSID had become a known access point (AP) to my nokia phone when the security was disabled. With security enabled, it no longer worked.
2) Set up the wireless security to WPA authentication type, TKIP encryption, PKS.
3) Chose a 15 (or more)-character-strong passphrase and set is up in the wireless router security settings.
4) Had the WLAN assistant of my Nokia E51 update the AP list.
5) Once listed as new, unknown SSID, I was able to set up from the phone my WLAN AP, via the OPTIONS tab where I was finally prompted for the passphrase. (Same prompt would NOT work unless SSID of a previously successful, unencrypted AP is changed)
The device resolved the connection which worked fine ever since.
I think that there is a bug with Nokia E51 which does not actually update the access point list and does not reload all of the details of a recently reconfigured AP which used to work fine with disabled security settings in the first place. The mobile phone can be forced to completely refresh the AP list (in Connection Manager> WLAN assistant) only if the SSID of the AP is renamed in the the router settings. It seems that only afterwards would the security handshake between the devices finally work out and establish a proper connection. There is definitely a bug with the Nokia E51 wlan manager!

E51 WLAN prob and nokia presenter

I have two issues with nokia E51 when I find WLAN access point and try to browse through them it gives me error of ' no gateway reply' i dont know how to do with it , same router works fine with my laptop but not mobile .
Secondly I want to have nokia wireless presenter on my E51 how can i get it working.
regrads
Hina

nobody knows, oh well mods u can delete this topic, thank u

Need HELP with sync settings foe nokia E51

Nokia E51
Hi, i am trying to setup the syc setting so i can attempt to transfer my contacts to my cars bluetooth, i have looked at some suggestions but they dont seem to work.
This is how far i am at the moment.
FIRST PAGE
INCLUDE IN SYNC - YES
DATABASE IN PHONE - C:contacts.cdb
REMOTE DATABASE - i am not sure what to put here it will not accept any wording and has a little red star next to if i try to.
SYNCHRONISATION TYPE - Both ways
SECOND PAGE
SERVER VERSION - 1.1
DATA BEARER - Bluetooth
HOST ADDRESS - as above i am not sure what to put in here and it will not accept any wording
USER NAME - Not sure what to put here either
PASSWORD - ****
ALLOW SYNC REQUESTS - Yes
ACCEPT ALL SYNC REQUESTS - Yes
Any help would be appreciated as i have tried everything to transfer my contacts but cant get it to work
Mark

Hi eden100990
No problems with this link at time of posting: http://europe.nokia.com/A41423552
Happy to have helped forum in a small way with a Support Ratio = 37.0

VoiP on Nokia E51 - Help Needed Urgently !!!

I am located in Copenhagen Denmark and I use a wireless network to connect to the internet. My Nokia E51 is also able to detect the same network when I scan for WLAN. However when I try to use it to make a net call it says ''NO WLAN COVERAGE FOUND''.
Probably a step by step guidance to configure the following would be useful -
- Wireless LAN
- SIP Settings
- Internet Tel
Help Please

Hi
Thanks to bife71 for the reply. The phone was able to detect the wireless network and I was able to use the Gizmo feature to make calls. The network name I was using was ''Netgear''. But since one month I shifted to a new apartment and there the network name is ''NETWORK'', and when I tried to connect using my E51, the WLAN scan is not able to pick up the wireless network at all. I use the same connection to browse the net and the connection is good. But the phone is not able to detect this connection and I am not able to make calls.
HELP PLEASE !!! Telephone charges are lot in Copenhagen and I badly need to use the Voip function for which I bought E51.

E51 Wlan Hidden SSID

We have lately purchase a couple of N95 and a couple E51 handsets. At the office we have a Linksys 4400N Access Point configured for 802.11G with WPA and hidden SSID.
The N95 handsets are able to connect with no problems whatsoever. The E51 however simply won't connect.
I tried taking the E51 home and connect it to my Airport Extreme 802.11G/N with the same results. At home I also have a hidden ssid so I tried to unhide it, with the ssid visible the E51 connects immediately. Hiding the ssid again (and changing the setting to hidden on the e51) and the handset is again unable to connect!
How is it that the N95 is able to connect and the E51 fails so miserably? I'd really prefer NOT to have to change the WiFi settings just because of a couple of handsets. Or simply say that for E51 users it just won't work.
This issue is really bugging me, searching the net has only resulted in few hits on this specific issue. Here's hoping that it is I who's making some kind of mistake (I doubt that however since I configured the N95 and the E51 side by side).

I was able to connect nokia e51 to WLAN with hidden SSID (I use WPA-PSK with AES).
Just define the access point first and choose "Network status" as hidden.
Here is short instruction from the manual:
"Connection > Access points.
2. Select Options > New access point to create a
new access point, or select an existing access point
from the list and then Options > Duplicate access
point to use the access point as a basis for the new
one.
3. Define the following settings.
• Connection name — Enter a descriptive name
for the connection.
• Data bearer — Select Wireless LAN.
• WLAN network name — To enter the service
set identifier (SSID), that is, the name that
identifies the specific WLAN, select Enter
manually. To select the network from the
WLANs in range, select Search for networks.
• Network status — Select Hidden if the network
you are connecting to is hidden or Public if it is
not hidden.
• WLAN network mode — If you select
Infrastructure, devices can communicate with
each other and with wired LAN devices through
a WLAN access point. If you select Ad-hoc,
devices can send and receive data directly with
each other, and no WLAN access point is needed.
WLAN security mode — You must select the
same security mode that is used in the WLAN
access point. If you select WEP (wired equivalent
privacy), 802.1x, or WPA/WPA2 (Wi-Fi protected
access), you must also configure the relevant
additional settings. See the device help for more
information.
• WLAN security settings — Edit the security
settings for the selected security mode.
• Homepage — Enter the web address of the page
you want to display as the home page when you
use this access point."
BR,
W.

E51 wlan can't connect

Hi,
I was using my Nokia E51 last night and downloaded wefi and werok apps thinking it might be safe, when i deleted werok, wefi went away as well and my wifi was working perfect. I woke up this morning trying to go on the internet, and nothing connects, it keeps saying "Connection not available" i try using my apps and it doesn't even let me go to search for wlan. Can anyone help?

Reset the E51. Dial *#7370# 12345 reformat, you'll lose all data. Make a backup first and restore without the settings.
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

Nokia E51 Questions

Hey there,
I am planning to buy a Nokia E51 but I have a couple of questions.
Is it possible to use voip to call people who are on skype (for free via wlan)
how many messages can the phone keep (inbox and outbox)
Is it possible to save these messages on the SD card,
and is it possible to export and import these messages to the pc and back.

11-Mar-2008 01:15 PM
vsriharsha wrote:
You might want to take a note of these issues before you decide (if you haven't already):
1. There is no USB charging support. You cannot connect your phone to the USB port of your PC/Laptop and let it (re-)charge. I just don't understand why Nokia fails to provide this simple, yet very useful feature.
2. Leaving the phone continuously on Wlan connection just drains your battery. So, better leave it hooked to the charger while it is connected to wlan.
Well I never had a phone where I could charge with the USB to be honest, and I don't think its that much of a hassle to take the charger with me if I know ill be gone a while.
And I have a couple of devices that use Wlan and I always switch it off when I don't use it, and in case I talk on skype on this phone (can last a couple hours easy) then I would just put it in the charger
BTW I like to charge my phone every night (and just leave it on for months really) what would be better for the phone itself (this one)
oh and thanks for telling me
Message Edited by ventalco on 11-Mar-2008 04:26 PM

How to find the max data transfer rate(disk speed) supported by mobo?

I plan on replacing my current HDD with a new and bigger HDD.
For this I need to know the max data transfer rate(disk speed) that my mobo will support. However, dmidecode is not telling me that. Am I missing something?
Here's dmidecode:
# dmidecode 2.11
SMBIOS 2.5 present.
80 structures occupying 2858 bytes.
Table at 0x000F0450.
Handle 0xDA00, DMI type 218, 101 bytes
OEM-specific Type
Header and Data:
DA 65 00 DA B2 00 17 4B 0E 38 00 00 80 00 80 01
00 02 80 02 80 01 00 00 A0 00 A0 01 00 58 00 58
00 01 00 59 00 59 00 01 00 75 01 75 01 01 00 76
01 76 01 01 00 05 80 05 80 01 00 D1 01 19 00 01
00 15 02 19 00 02 00 1B 00 19 00 03 00 19 00 19
00 00 00 4A 02 4A 02 01 00 0C 80 0C 80 01 00 FF
FF 00 00 00 00
Handle 0xDA01, DMI type 218, 35 bytes
OEM-specific Type
Header and Data:
DA 23 01 DA B2 00 17 4B 0E 38 00 10 F5 10 F5 00
00 11 F5 11 F5 00 00 12 F5 12 F5 00 00 FF FF 00
00 00 00
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: Dell Inc.
Version: A17
Release Date: 04/06/2010
Address: 0xF0000
Runtime Size: 64 kB
ROM Size: 4096 kB
Characteristics:
PCI is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
Selectable boot is supported
EDD is supported
Japanese floppy for Toshiba 1.2 MB is supported (int 13h)
3.5"/720 kB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
ACPI is supported
USB legacy is supported
BIOS boot specification is supported
Function key-initiated network boot is supported
Targeted content distribution is supported
BIOS Revision: 17.0
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: Dell Inc.
Product Name: OptiPlex 755
Version: Not Specified
UUID: 44454C4C-5900-1050-8033-C4C04F434731
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Handle 0x0200, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Dell Inc.
Product Name: 0PU052
Version:
Handle 0x0300, DMI type 3, 13 bytes
Chassis Information
Manufacturer: Dell Inc.
Type: Space-saving
Lock: Not Present
Version: Not Specified
Asset Tag:
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: None
Handle 0x0400, DMI type 4, 40 bytes
Processor Information
Socket Designation: CPU
Type: Central Processor
Family: Xeon
Manufacturer: Intel
ID: 76 06 01 00 FF FB EB BF
Signature: Type 0, Family 6, Model 23, Stepping 6
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (FXSAVE and FXSTOR instructions supported)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Multi-threading)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Not Specified
Voltage: 0.0 V
External Clock: 1333 MHz
Max Speed: 5200 MHz
Current Speed: 2666 MHz
Status: Populated, Enabled
Upgrade: Socket LGA775
L1 Cache Handle: 0x0700
L2 Cache Handle: 0x0701
L3 Cache Handle: Not Provided
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Core Count: 2
Core Enabled: 2
Thread Count: 2
Characteristics:
64-bit capable
Handle 0x0700, DMI type 7, 19 bytes
Cache Information
Socket Designation: Not Specified
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 32 kB
Maximum Size: 32 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: None
System Type: Data
Associativity: 8-way Set-associative
Handle 0x0701, DMI type 7, 19 bytes
Cache Information
Socket Designation: Not Specified
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Varies With Memory Address
Location: Internal
Installed Size: 6144 kB
Maximum Size: 6144 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: Single-bit ECC
System Type: Unified
Associativity: <OUT OF SPEC>
Handle 0x0800, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: PARALLEL
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-25 female
Port Type: Parallel Port PS/2
Handle 0x0801, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: SERIAL1
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-9 male
Port Type: Serial Port 16550A Compatible
Handle 0x0802, DMI type 126, 9 bytes
Inactive
Handle 0x0803, DMI type 126, 9 bytes
Inactive
Handle 0x0804, DMI type 126, 9 bytes
Inactive
Handle 0x0805, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB1
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0806, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB2
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0807, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB3
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0808, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB4
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0809, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB5
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080A, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB6
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080B, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB7
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080C, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB8
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080D, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: ENET
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: RJ-45
Port Type: Network Port
Handle 0x080E, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: MIC
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x080F, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: LINE-OUT
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0810, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: LINE-IN
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0811, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: HP-OUT
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0812, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: MONITOR
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-15 female
Port Type: Video Port
Handle 0x090A, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT1
Type: x1 Proprietary
Current Usage: In Use
Length: Long
Characteristics:
PME signal is supported
Handle 0x0901, DMI type 126, 13 bytes
Inactive
Handle 0x0902, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT2
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 2
Characteristics:
5.0 V is provided
3.3 V is provided
PME signal is supported
Handle 0x0903, DMI type 126, 13 bytes
Inactive
Handle 0x0904, DMI type 126, 13 bytes
Inactive
Handle 0x0905, DMI type 126, 13 bytes
Inactive
Handle 0x0906, DMI type 126, 13 bytes
Inactive
Handle 0x0907, DMI type 126, 13 bytes
Inactive
Handle 0x0908, DMI type 126, 13 bytes
Inactive
Handle 0x0A00, DMI type 10, 6 bytes
On Board Device Information
Type: Video
Status: Disabled
Description: Intel Graphics Media Accelerator 950
Handle 0x0A02, DMI type 10, 6 bytes
On Board Device Information
Type: Ethernet
Status: Enabled
Description: Intel Gigabit Ethernet Controller
Handle 0x0A03, DMI type 10, 6 bytes
On Board Device Information
Type: Sound
Status: Enabled
Description: Intel(R) High Definition Audio Controller
Handle 0x0B00, DMI type 11, 5 bytes
OEM Strings
String 1: www.dell.com
Handle 0x0D00, DMI type 13, 22 bytes
BIOS Language Information
Language Description Format: Long
Installable Languages: 1
en|US|iso8859-1
Currently Installed Language: en|US|iso8859-1
Handle 0x0F00, DMI type 15, 29 bytes
System Event Log
Area Length: 2049 bytes
Header Start Offset: 0x0000
Header Length: 16 bytes
Data Start Offset: 0x0010
Access Method: Memory-mapped physical 32-bit address
Access Address: 0xFFF01000
Status: Valid, Not Full
Change Token: 0x00000018
Header Format: Type 1
Supported Log Type Descriptors: 3
Descriptor 1: POST error
Data Format 1: POST results bitmap
Descriptor 2: System limit exceeded
Data Format 2: System management
Descriptor 3: Log area reset/cleared
Data Format 3: None
Handle 0x1000, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 8 GB
Error Information Handle: Not Provided
Number Of Devices: 4
Handle 0x1100, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_1
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Manufacturer: AD00000000000000
Handle 0x1101, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_3
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1102, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_2
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1103, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_4
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1300, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000FDFFFFFF
Range Size: 4064 MB
Physical Array Handle: 0x1000
Partition Width: 1
Handle 0x1400, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x1100
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 1
Handle 0x1401, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FDFFFFFF
Range Size: 2016 MB
Physical Device Handle: 0x1101
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 1
Handle 0x1402, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x1102
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 1
Handle 0x1403, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FDFFFFFF
Range Size: 2016 MB
Physical Device Handle: 0x1103
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 1
Handle 0x1410, DMI type 126, 19 bytes
Inactive
Handle 0x1800, DMI type 24, 5 bytes
Hardware Security
Power-On Password Status: Enabled
Keyboard Password Status: Not Implemented
Administrator Password Status: Enabled
Front Panel Reset Status: Not Implemented
Handle 0x1900, DMI type 25, 9 bytes
System Power Controls
Next Scheduled Power-on: *-* 00:00:00
Handle 0x1B10, DMI type 27, 12 bytes
Cooling Device
Type: Fan
Status: OK
OEM-specific Information: 0x0000DD00
Handle 0x1B11, DMI type 27, 12 bytes
Cooling Device
Type: Fan
Status: OK
OEM-specific Information: 0x0000DD01
Handle 0x1B12, DMI type 126, 12 bytes
Inactive
Handle 0x1B13, DMI type 126, 12 bytes
Inactive
Handle 0x1B14, DMI type 126, 12 bytes
Inactive
Handle 0x2000, DMI type 32, 11 bytes
System Boot Information
Status: No errors detected
Handle 0x8100, DMI type 129, 8 bytes
OEM-specific Type
Header and Data:
81 08 00 81 01 01 02 01
Strings:
Intel_ASF
Intel_ASF_001
Handle 0x8200, DMI type 130, 20 bytes
OEM-specific Type
Header and Data:
82 14 00 82 24 41 4D 54 01 01 00 00 01 A5 0B 02
00 00 00 00
Handle 0x8300, DMI type 131, 64 bytes
OEM-specific Type
Header and Data:
83 40 00 83 14 00 00 00 00 00 C0 29 05 00 00 00
F8 00 4E 24 00 00 00 00 0D 00 00 00 02 00 03 00
19 04 14 00 01 00 01 02 C8 00 BD 10 00 00 00 00
00 00 00 00 FF 00 00 00 00 00 00 00 00 00 00 00
Handle 0x8800, DMI type 136, 6 bytes
OEM-specific Type
Header and Data:
88 06 00 88 5A 5A
Handle 0xD000, DMI type 208, 10 bytes
OEM-specific Type
Header and Data:
D0 0A 00 D0 01 03 FE 00 11 02
Handle 0xD100, DMI type 209, 12 bytes
OEM-specific Type
Header and Data:
D1 0C 00 D1 78 03 07 03 04 0F 80 05
Handle 0xD200, DMI type 210, 12 bytes
OEM-specific Type
Header and Data:
D2 0C 00 D2 F8 03 04 03 06 80 04 05
Handle 0xD201, DMI type 126, 12 bytes
Inactive
Handle 0xD400, DMI type 212, 242 bytes
OEM-specific Type
Header and Data:
D4 F2 00 D4 70 00 71 00 00 10 2D 2E 42 00 11 FE
01 43 00 11 FE 00 0F 00 25 FC 00 10 00 25 FC 01
11 00 25 FC 02 12 00 25 FC 03 00 00 25 F3 00 00
00 25 F3 04 00 00 25 F3 08 00 00 25 F3 0C 07 00
23 8F 00 08 00 23 F3 00 09 00 23 F3 04 0A 00 23
F3 08 0B 00 23 8F 10 0C 00 23 8F 20 0E 00 23 8F
30 0D 00 23 8C 40 A6 00 23 8C 41 A7 00 23 8C 42
05 01 22 FD 02 06 01 22 FD 00 8C 00 22 FE 00 8D
00 22 FE 01 9B 00 25 3F 40 9C 00 25 3F 00 09 01
25 3F 80 A1 00 26 F3 00 A2 00 26 F3 08 A3 00 26
F3 04 9F 00 26 FD 02 A0 00 26 FD 00 9D 00 11 FB
04 9E 00 11 FB 00 54 01 23 7F 00 55 01 23 7F 80
5C 00 78 BF 40 5D 00 78 BF 00 04 80 78 F5 0A 01
A0 78 F5 00 93 00 7B 7F 80 94 00 7B 7F 00 8A 00
37 DF 20 8B 00 37 DF 00 03 C0 67 00 05 FF FF 00
00 00
Handle 0xD401, DMI type 212, 172 bytes
OEM-specific Type
Header and Data:
D4 AC 01 D4 70 00 71 00 03 40 59 6D 2D 00 59 FC
02 2E 00 59 FC 00 6E 00 59 FC 01 E0 01 59 FC 03
28 00 59 3F 00 29 00 59 3F 40 2A 00 59 3F 80 2B
00 5A 00 00 2C 00 5B 00 00 55 00 59 F3 00 6D 00
59 F3 04 8E 00 59 F3 08 8F 00 59 F3 00 00 00 55
FB 04 00 00 55 FB 00 23 00 55 7F 00 22 00 55 7F
80 F5 00 58 BF 40 F6 00 58 BF 00 EB 00 55 FE 00
EA 00 55 FE 01 40 01 54 EF 00 41 01 54 EF 10 ED
00 54 F7 00 F0 00 54 F7 08 4A 01 53 DF 00 4B 01
53 DF 20 4C 01 53 7F 00 4D 01 53 7F 80 68 01 56
BF 00 69 01 56 BF 40 FF FF 00 00 00
Handle 0xD402, DMI type 212, 152 bytes
OEM-specific Type
Header and Data:
D4 98 02 D4 70 00 71 00 00 10 2D 2E 2D 01 21 FE
01 2E 01 21 FE 00 97 00 22 FB 00 98 00 22 FB 04
90 00 11 CF 00 91 00 11 CF 20 92 00 11 CF 10 E2
00 27 7F 00 E3 00 27 7F 80 E4 00 27 BF 00 E5 00
27 BF 40 D1 00 22 7F 80 D2 00 22 7F 00 45 01 22
BF 40 44 01 22 BF 00 36 01 21 F1 06 37 01 21 F1
02 38 01 21 F1 00 39 01 21 F1 04 2B 01 11 7F 80
2C 01 11 7F 00 4E 01 65 CF 00 4F 01 65 CF 10 D4
01 65 F3 00 D5 01 65 F3 04 D2 01 65 FC 00 D3 01
65 FC 01 FF FF 00 00 00
Handle 0xD403, DMI type 212, 157 bytes
OEM-specific Type
Header and Data:
D4 9D 03 D4 70 00 71 00 03 40 59 6D 17 01 52 FE
00 18 01 52 FE 01 19 01 52 FB 00 1A 01 52 FB 04
1B 01 52 FD 00 1C 01 52 FD 02 1D 01 52 F7 00 1E
01 52 F7 08 1F 01 52 EF 00 20 01 52 EF 10 21 01
52 BF 00 22 01 52 BF 40 87 00 59 DF 20 88 00 59
DF 00 E8 01 66 FD 00 E9 01 66 FD 02 02 02 53 BF
00 03 02 53 BF 40 04 02 53 EF 00 05 02 53 EF 10
06 02 66 DF 00 07 02 66 DF 20 08 02 66 EF 00 09
02 66 EF 10 17 02 66 F7 00 18 02 66 F7 08 44 02
52 BF 40 45 02 52 BF 00 FF FF 00 00 00
Handle 0xD800, DMI type 126, 9 bytes
Inactive
Handle 0xDD00, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 00 DD 00 01 00 00 00 10 F5 00 00 00 00 00
00 00 00
Handle 0xDD01, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 01 DD 00 01 00 00 00 11 F5 00 00 00 00 00
00 00 00
Handle 0xDD02, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 02 DD 00 01 00 00 00 12 F5 00 00 00 00 00
00 00 00
Handle 0xDE00, DMI type 222, 16 bytes
OEM-specific Type
Header and Data:
DE 10 00 DE C1 0B 00 00 10 05 19 21 01 00 00 01
Handle 0x7F00, DMI type 127, 4 bytes
End Of Table
Hdparm also does not tell me the max data transfer rate (disk speed) of my current drive although this link : www.wdc.com/en/library/sata/2879-001146.pdf says that it is 3.0Gb/s
and here's hdparm -I /dev/sda
/dev/sda:
ATA device, with non-removable media
Model Number: WDC WD800JD-75JNC0
Firmware Revision: 06.01C06
Standards:
Supported: 6 5 4
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
CHS current addressable sectors: 16514064
LBA user addressable sectors: 156250000
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 76293 MBytes
device size with M = 1000*1000: 80000 MBytes (80 GB)
cache/buffer size = 8192 KBytes
Capabilities:
LBA, IORDY(can be disabled)
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 8
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
SET_MAX security extension
Automatic Acoustic Management feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* SMART error logging
* SMART self-test
* Gen1 signaling speed (1.5Gb/s)
* Host-initiated interface power management
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
Last edited by Inxsible (2011-03-27 04:40:49)

I just checked my BIOS and my current setting is set at IDE although it also mentions that the default should be AHCI. Currently I have a dual boot of Windows 7 (need it for Tax software) and Arch
So I guess, when I get the new HDD, I will first set it to AHCI and then install the OSes on it. See if NCQ helps any, and if not I will turn it back and re-install (if I have to). I am planning to have Windows only in virtualbox in the new drive.
Anyhoo, while I was in the BIOS I found two things which I had questions about :
1) Under Onboard Devices --> Integrated NIC , my setting is currently set at "On w/PXE" and it says the default should be just "On". Would it be ok to change it back to On since its a single machine and its not booting an OS on any server. I just don't want to have to re-install anything now since I will be doing that in the new HDD.
2) How would I know whether my BIOS would support a 64 bit OS in Virtualbox? I checked some setting under Virtualization, but they weren't very clear.
I will edit this post and let you know exactly what settings were present under the Virtualization sub-section.

KT3 Ultra ARU Slow HD Transfer Rates

Hello,
First, please see my system information at the bottom of this message.
I have a MSI KT3 Ultra ARU motherboard and have installed a Maxtor ATA133 60GB hard drive with 2 MB cache. The hard drive is jumpered as Master and is connected all by itself on the IDE1 ribbon cable. On IDE2 I have a CDRW (Master) and a CD-ROM (Slave). My other hard drive (WD 120GB ATA100 8 MB cache) is on IDE3 and is set up in RAID 1+0 stripe.
I recently ran the Sandra file system benchmark on my hard drives with what I think are very discouraging results. My Maxtor drive on IDE1 scored 32 MB/s and my WD drive on IDE3 came in at 23 MB/s. Those are some stinky results aren’t they?
I checked my Device Manager under IDE ATA/ATAPI Controllers and it indicates that for my Primary IDE Channel the current transfer mode for device 0 is Ultra DMA Mode 6. I don’t know how to check the transfer mode on my IDE3 hard drive.
Question #1: Are my 32 MB/s and 23 MB/s results slow for my hardware?
Question #2: If these results are slow, how can I increase the transfer rates?
Please help!
Thank you!!!!
My System
AMD Athlon XP 3000+
MSI KT3 Ultra ARU MOBO
2 x 256MB DDR PC2700 SDRAM
ATI Radeon 9600XT 256MB
Western Digital WD1200JB 120GB Caviar HD ATA100 8MB Cache 1+0 Stripe/RAID0
Maxtor 6Y060L0 60GB HD ATA133
Pioneer DR-A04S CD-ROM 32X
Lite-On LTR-48125W 48x12x48 CDRW
TTGI TT-350SS (350W) Power Supply
PSU Ratings: +3.3V/28A +5V/35A +12V/16A
Windows XP Home SP2

These tranfer rates seem fine for sequential read rates. The maxtor drive is at mode 6 and the WD should be at mode 5 if its ATA100.

Gigabit ethernet + TC doesn't mean gigabit transfer rates to the TC drive..

Alright.... I've spent a ton of time trying to figure this out (probably more than I should have) and I thought I'd post my findings so that either a) I'll save someone else time out there or b) someone can tell me I'm a complete moron
So I had an airport extreme. I replaced it with a Time Capsule. I have a Windows (boooo) PC connecting directly to my TC using a gigabit ethernet card (which I bought specifically connect it to the TC) so (I thought) I could enjoy gigabit transfer speeds to the internal hard drive from the wired PC. I had some fun plans of shoving my itunes directory on the TC and letting appletv sync (yes through my pc) and keeping lots of videos there, etc. Who cares - it'd be at gigabit speeds! But, in reality, things didn't quite work that way (though my itunes directory does still live on my TC...for now).
Well, I had a semi-unique situation to do some pretty massive testing because I have 2 gigabit network cards, 1 100mb network card, and a wireless-n network card and two internal hard drives - both very fast. I also tried Cat 5, Cat 5e, and a Cat 6 cable.
And here's what I (think I) figured out:
The hard drive in TC can not achieve gigabit transfer speeds. Your transfer rates will be limited by the IO to the hard drive. In fact, it can't even come close.
Using my "fastest" setup - so Cat 6, fastest internal drive, gigabit ethernet, and transferring a file exactly 1 gig in size I was able to have a sustained transfer rate of 140 megabit per second - that's 17.4 MB/s for folks not wanting to do the math (that's reading FROM the TC. Writing TO the TC dropped the speed down to 106 megabit/second or 13.35 MB/s). Going to a 5e cable knocked that down to 130 megabit a second. Putting in a Cat 5 cable knocked me down to 110 megabit a second. Switching between my two gigabit network cards did nothing. Switching my cards between two computers did nothing.
Now, just changing the above setup to use my 100Mb network card resulted in these results: 67 megabit read (8.4MB/s) and 65 megabit write (8MB/s)...
And using wireless N, I got about 10MB/s up and down.
And just as a final test, connecting my two computers together using the 2 gigabit network cards through the TC, I was able to achieve standard gigabit speeds.
SO what does this all mean?
I think the IO to the hard drive in the TC can only read at about 140 megabit/s and write at about 110 megabit/s. I'm not sure if it's the HD itself or how it's connecting to the TC - but that's why I'm not aware of anyone getting faster transfer rates to the drive in the TC (maybe you guys are?). The gigabit ports themselves are fine - and if you're doing anything from one gigabit port to another gigabit port you'll be fine.
So stop beating yourself up trying to find some elusive XP specific issue with gigabit transfer rates (though vista had a problem - shocker), or that you must have a defective gigabit card (which is why I have two cards now instead of one :)), or that your cable must be bad ("maybe my cat 5e isn't good enough?")... it's just this drive ... or how the drive is connecting to the network - can't handle the gigabit speeds.
Unless someone else out there has another explanation? Do these speeds mesh with what you're seeing in "optimal" situations? Or maybe there's just a throttle switch for goobers like me using Windows instead of MacOS!

Hi,
the interfaces available today which connect your drives integrated electronics to your computer can handle that speeds. but the drive itself is limited by the mechanical things going on in there
You can get such transfer speeds if the data you request is in the cache of the drives internal electronics for example. Some drives have 8 MB of cache memory. So if you request to read or write less than 8 mb and (in the read case) you are lucky enough to have those few megabytes cached then you may get that performance
Regards,
somi

Determining Data transfer rate through modem in java

Hi,
I want to write an application in java which will communicate with
connected modem of the system and it will detect the data transfer rate.
I want to know how much data is transferring(upload/download)through modem and in a specific time how much data is transferred.
I will give some max upload/downloading limit for a specific time and if data transfer exceeds that limit,it will show message.
e.g if i fix max upload/download data transfer limit by the modem is say 10GB/20GB for a specific time span say for 15 days.Then my program automatically will start when the Modem will be connected and keep a log of data transfer(upload/download)and if data transfer goes beyond limit then it will show message.Also i would be able to see how much data is transferred for any specific day.
I want to know this type of application is possible in java.If yes then
which API's i need to use.
If this type of program is available in some site in other language then also i will be helpful.Pl give the links.
byeeeeeeee
Pradipto

Hi,
i want to do it in java only to explore the power of
java.I agree with Abuse, Java is not designed for such applications. I'm not even sure if you can solve your problems with Java.

How to achieve the maximum file transfer rate from PXI to local host?

I will have to copy a huge amount of data (as big as 50 GB) from a PXI-8106 unit on site to a laptop. Currently it would take several hours. It is critical to max out the data transfer rate.
The standard method we've been using is just drag and drop using Windows Explorer via FTP. I tried to use FTP VIs with Filezilla Server as well but the transfer rate is only like 1.5 MB/s. Is this normal? Once I saw it was 3.0 MB/s but for some reason, that isn't happening now.
For another option, I tried to transfer data to a USB flash drive but it's even slower. As far as I know, USB 2.0 transfer rate is supposed to be around 60 MB/s but why would it be slower than 1.5 MB/s? What could be the speed limiting factor in my file transfer setup?
Any tips on improving file transfer rate would be appreciated!

Sustained 40 MB/s? That is my dream speed! The maximum speed I've ever seen here was about 25 MB/s, which is still very good, and that happened only after copying back and forth, which I explained above. Let me go through what I did with screencaps first.
These are the test tdms files to transfer in the PXI: an original file witten in the PXI and its copy file. I copied the original file from PXI to laptop and renamed it (added '_copy') and then copied it back to PXI.
FTP module is transferring the original file to the Filezilla server on laptop. Note the low speed.
FTP module is transferring the copy file to the Filezilla server on laptop. Note the higher speed.
This is the FTP sub VI I'm using. It transfers files in sub-folders (one level lower), too. The data connection is set to 'passive' on the FTP Put Multiple Files VI but it doesn't seem to make any difference. I attach the sub VI.
You tried the file transfer with a 500 MB text file. Would there be any difference if the file type was tdms? Would the RAM size matter? It is 2GB here.
And the LED is orange, which means Gigabit.
Another question: Is there any way to programmatically stop file transfer in progress? Currently, I just have to restart the PXI.
Thank you!
Attachments:
FTP.vi ‏40 KB

What is max internal hard drive transfer rate compatible with a 2007 MacBook Pro?

In attempt to upgrade my mid-2007 MacBook Pro (Intel Core 2 Duo), I bought a Seagate 750GB listed as compatible with my computer on MacSales.com . . .
Seagate Momentus XT ST750LX003 750GB 7200 RPM 32MB Cache 2.5" SATA 6.0Gb/s Solid State Hybrid Drive -Bare Drive
Installation appeared to go well and I ran an extended hardware test with no issues found. However, the drive is listed at 5.46 TB (would be nice) and I get an input/output error when attempting to partition. I can initiate an erase, but after the time I would suspect it would take to erase the drive, I get an input/output error - it seems to appear after the first 750 GB of the '5.5 TB' was erased. At all times, the drive is not recognized when I attempt to install OS X from original discs.
I suspect the 6.0 GB/s transfer capacity of the hard drive is not compatible with the MacBook Pro. The drive came with 4 jumper pins but no jumper and no label diagram to set a slower transfer rate. I called Seagate, Newegg, OWC, and Apple, but no one has compatibility info for my MacBook Pro. To them, it appears I am running the first tests of this new technology with an 'older' MacBook Pro.
My MBP has had no issues - I'd like to keep her going with the optimum internal hard drive capacity, but don't necessarily want to set up a test bench in my house (though my kids would enjoy destroying it) and pay several shipping and restocking fees to test new hard drives.
The original drive had a 1.5 GB/s transfer rate. Does anyone know the maximum transfer rate compatible with a 2007 MacBook Pro? 3.0 GB/s? 1.5 GB/s? Thank you.

No spinning hard drive will transfer data faster then 60-80MB a second. The XT models have a flash storage area that is used when reading and writing data that can make it Appear faster in some situations. That flash memory if only 8 or 16GBs in side, I forget which one.
The drie is rated to work on 6GB SATA bus but it certainly can not transfer data that fast. It should be backword compatible to work on slower buses.
Your drive is 750GBs in size. Not wure where you are getting this 5.5TB (that is 5.5 Tera Bytes which is 5500 Giga Bytes. Your drive is under 1TB)
What are you using to partition the drive? Disk Utilities from the original install DVD?
You need to install on your old drive, Update it from the Apple Website then clone it to the new drive. The version of OSX you are using may not function correctly with that large of a drive. Or get yourself a copy of Snow Leopard, retail disk for $29 from Apple, and do all the partitioning and installing with that version od OSX.

Nokia E51 WLAN transfer rates

Similar Messages

Maybe you are looking for