Nokia E70, trying to connect to WLAN, problem with...

Hello,
I just go a Nokia E70 and am trying to connect to my home wifi internet... I can detect it etc, but cannot configure the access point... could someone please help me ?
The problem is that my WEP key is, from what I see from my internet provider, 26 characters long, and I cannot enter that long a WEP key in the phone...
Thanks in advance,
Tenshi5

Hi,
Ensure that WEP key is in HEX and not ASCII
Hope it helps

Similar Messages

  • Can SAP GRC AC 5.3 connect without any problem with SAP R/3 4.7 Enterprise?

    hello,
    I went to the PAM in the SAP Marketplace to see if SAP GRC AC 5.3 could connect to SAP R/3 4.7 Enterprise but I can't see all the "Add-On Product Version for...", it's cut off.
    Can SAP GRC AC 5.3 connect without any problem with SAP R/3 4.7 Enterprise?
    If I can't is there any proof about it? I have to show it to a client.
    Best Regards,
    Pablo Mortera,

    Pablo,
    GRC AC 5.3 works perfectly fine with SAP's R/3 4.6c, mySAP ERP 4.7 and ECC systems. In fact we have two 4.7 Enterprise systems connected to GRC AC 5.3 system.
    You can get the details of supported SAP ERP systems under prerequisite section of Info page of GRC AC 5.3 , it can be accessed on marketplace at -
    Downloads-->Installations and Upgrades - Entry by Application Group > SAP Solutions for Governance, Risk, and Compliance>SAP GRC Access Control>SAP GRC ACCESS CONTROL>SAP GRC ACCESS CONTROL 5.3
    Just ensure to have proper BASIS and ABAP support pack level as mentioned in prerequisites.
    Regards,
    Amol

  • I tried to connect SAP BW7.0 with use Jco2.1.7...

    I tried to connect SAP BW7.0 with Jco2.1.7(64bit Itanium) in Microsoft Windows 2003 on IA64 and x86_64 with SUN JSE 1.4.2 (64-bit VM).
    But I got error as followings.
    java.lang.ExceptionInInitializerError: JCO.classInitialize(): Could not load middleware layer 'com.sap.mw.jco.rfc.MiddlewareRFC'
    JCO.nativeInit(): Could not initialize dynamic link library sapjcorfc [no sapjcorfc in java.library.path]. java.library.
    path [C:\fds2\jrun4\bin;.;C:\WINDOWS\system32;C:\WINDOWS;C:\oracle\product\10.2.0\client_1\bin;C:\WINDOWS\system32;C:\WI
    NDOWS;C:\WI
    what's wrong?
    one more question
    What is the "Microsoft C runtime libraries version 7"?
    Message was edited by: kooknam han

    Hi,
    I think it's not possible to create a Universe directly on ECC 6.0.
    You need to use a Data Federator for this to work. A Data Federator view is created on top of the ECC source using the connector then you can create Universe on top of Data Federator.
    Check the below for more info on the same.
    SAP BusinessObjects Web Intelligence Reporting for SAP ERP
    Data Federator Installation Guide:
    http://help.sap.com/businessobject/product_guides/boexi3SP1/en/xi3_sp1_df_install_en.pdf
    User Guide on Data Federator:
    http://help.sap.com/businessobject/product_guides/boexi3SP2/en/xi3_sp2_df_userguide_en.pdf
    Hope it helps.
    Regards,
    Raghu

  • HT6129 I am trying to connect my itunes account with disney anywhere app but when i click connect to itunes from disney app and am redirecting to itunes store, nothing happens

    I am trying to connect my itunes account with disney anywhere app but when i click connect to itunes from disney app and am redirecting to itunes store, nothing happens

    What happens when you click the "Download" button for Mountain Lion? Do you get any response (error messages, etc.) from the Mac App Store?
    Clinton

  • TS2662 I am trying to connect a wireless keyboard with a numeric pad to my (recent) iMac, but it does not see the numeric pad. Any advice?

    I am trying to connect a wireless keyboard with a numeric pad to my (recent) iMac running Mountain Lion. I followed all recommendations in article http://support.apple.com/kb/TS3048#1.  My computer recognises the alpha part, but it does not see the numeric pad. Any advice?

    Hello:
    I would try resetting the PRAM and SMC.
    Barry

  • Wlan problem with nokia n95 8g RM-320

    i have nokia n95 8g RM-320  frimware 35.0.00.1
    wlan stopped working
    and i did a lot of things but nothing happened
    1- format phone memory
    2- reinstall software many times
    3- restore factory settings
    4- restore beackup without settings
    the problem is
    some times the phone can find the wlan and sometimes not
    and if it find the wlan it cant connect to the connection
    ps. nothing wrong with my access point because i tried another phone and it worked fine
    plz i need help i really need this function to work again

    plz help !!

  • Problems when trying to connect over TCP/IP with DHCP

    Hello everybody,
    I have problems to get a TCP/IP connection to my Blackfin board.
    There is an error message, see in the attached files.
    I have also Problems with the UART Interface can't run it with the Code Examples!
    Best Regards,
    Johannes
    Attachments:
    TCP IP Faults.doc ‏146 KB

    Johannes,
    The Blackfin lwip stack expects a DHCP server to assign it an IP, you cannot just connect a crossover cable between your computer and the EZKIT (unless your computer happens to be running a DHCP server). Connect your computer and the EZKIT and your computer to a router/switch so that the DHCP server on it can assign IPs to both. Also, you appear to be using the code from the example called Print EZKIT IP Address.vi. I recommend putting this code into a while loop with a wait.
    Message Edited by Michael P on 07-27-2006 10:57 AM
    Michael P
    National Instruments

  • WLAN Problem with 5800 - No Gateway Reply

    Hey, basically my problem is similar to most of the ones about the 5800, but I'm trying to connect to my university network, so I can't play around with any of the settings of the network, I was just wondering if anyone had connected to a network like this one, or if they have overcome the no gateway reply problem, or just if you had any advice. Thanks, Phil

    Hi,
    search this forum with the following search term:
    "e65 WLAN 802.1x TKIP PEAPv0"
    From the results you should get some ideas on how to proceed.
    Cheers,
    Timo
    Message Edited by timou on 24-Feb-2009 12:26 PM
    2110i | 3110 | 6110 | 6210i | 9210i | N95

  • Nokia 5800 - Can't connect to the internet with wi...

    I can't connect anymore to the internet with my nokia 5800, not with wi-fi or with 3G and i was able to do it before. When i try to open a page and then i select the connection type it gives me a message "Connection not available" and then another message shows "web: operation failed". I have never changed the configurations to any of the connection settings, so if it was working before why is it not working now? Someone can help me?

    Hi,
    Don't know if this will help you, but I think I had a similar problem. Maybe this can help you.
    Here's what my problem was, and how I solved it:
    Problems:
    * YouTube stopped asking what kind of connection I wanted, and always connected through 3g, which was OK when I was home, but not good when I was abroad and had access to Wifi.
    * After being abroad using Wifi to connect to Skype, GMail (Google's Java client) and Opera mini I was no longer asked at home if I wanted to connect via 3g rather than Wifi.
    This was a problem as I don't have Wifi at my home, and I did not want to connect to my personal email etc through a public Wifi. I prefered using 3g at home as I'm paying a fixed rate to my mobile operator in any case, and don't pay per data amount downloaded.
    Solution:
    Removing and reinstalling above programs (YouTube, Skype, GMail and Opera Mini) did not help. Neither did resetting the phone - option 1 in the suggestions below that resets the phone to store settings, but that still keeps all personal data.)
    I did not feel like whipping everything on my phone so instead what I managed to solve the problems as follows:
    Under Settings --> Connectivity -->Destinations -->Options --> Manage --> New destination:
    Create a new destination name.
    I made one I called Wifi. Then choose an icon from the suggested icons.
    Then go into Internet (under the suggested network destinations), and one by one click on all network destinations that are wifi connections and move them to the new Wifi destination that you've just created. This is done by moving the cursor to the wifi point and --> Options --> Organise --> Move to other dest. --> <Choose your newly created Wifi destination>
    Once this is done you should have your 3g access points left under Internet, while all your wifi access points are under your Wifi destination.
    Now under the Network destinations menu (where you can see all your access points listed e.g. Access point, Internet, Multimedia msg., WAP services, Wifi (the one just created) and Uncatergorised) choose Options again and -->Default connection --> Always ask.
    It will now always ask you which connection to use; if you want 3g choose Internet, but if you want to use wifi choose Wifi (the destination just created).
    To those who wonder: I always had the settings set to "Always ask". However, in the past because both Wifi and 3g access points where all under the Internet destination I could not choose between them, and after being abroad Wifi always had priority over 3g, and I could not change this priority despite trying to, so I came up with this little hack instead. This works for me. Hope other people find it helpful too!
    Åsa

  • Error trying to connect Portal 7.03 with SAP R/3

    Hi everyone,
    We're trying to connect the SAP Portal 7.03 with any SAP R/3 transaction.
    We're connecting with the option: System Management - Support - SAP Application - SAP Transaction and we select any transaction, but we're getting the next error:
    Content pass of application integrator failed.
    Component name: u2018com.sap.portal.appintegrator.sap.transactionu2019,
    Top layer: u2018Transaction/DragAndRelateLlayeru2019,
    Producer ID (FPN): 'null',
    System Alias: u2018SAP_QASu2019
    Application URL u2018:///sap (ZT00T1NPU3VJN2p1VHNHUWs2NHIyUIFnLS1ZRypKSTNxQ3ZqeG pWWU1Zc0s3TGhRLS0=) /bc/gui/sap/its/webguiu2019 is not valid! please check the protocol and host entries for system 'SAP_QAS'.
    Does anybody knows why we're getting this?
    We appreciate your help!
    Edited by: vemontoya on Feb 6, 2012 5:48 PM

    Hi,
    Unfortunately the status - "System waiting for something" is very vague. There could be a lot of things that you might have to look into.
    1. Are you able to log into the ECC system? If yes, you may want to activate the webgui related services. If you are running it for the first time, you might have to run the program - SIAC_PUBLISH_ALL_INTERNAL
    2. you may also want to look at the user with which you log in - does the user have authorization to run the transaction.
    3.  Check your system object properties if all the system properties - client, port etc. are specified correctly.
    In short, there could be a lot of possibilities of what the problem could be, although the real problem may be really small. If you can post something more specific, I will be able to help you.
    Hope this helps
    Prathamesh

  • "error 3194 and have tried all recommended steps, first problem with this iphone"

    Hi, for a few months now I've been using my brother's old iPhone 3GS as an iPod, and I haven't jailbreaken it or anything of the sort, and I've installed every update since, and today I installed the newest update and since it has been in recovery mode and whenever I connect it to iTunes and try to restore (I backed up a few days ago) I am greeted with an iTunes message saying "error 3194" and I've tried everything mentioned in the specific update article for it except for the one pertaining to a .ipsw because when I go to advanced settings I am unable to find anything of the sort. And it'd be much appreciated if any of you could help! Also, I am using a windows computer, not a mac, and have never had problems with this iPhone until this new update.

    It is usually given as a communication error between Apple, iTunes (your computer), iPhone. Somewhere they are not communicating, so the iOS you are trying to install cannot be approved by Apple. Trouble shooting steps include, making sure you have Current iTunes installed, make sure your Hosts file of computer is not blocking Apple. Try restoring on another computer.

  • I am trying to connect my mac air with my tv but it is not connecting

    hi i am trying to connect my mac book air with my tv but it is not connecting . please tell me the procedure .

    Welcome to Apple Discussions
    Help us help you. The more complete the description of your problem is (what OS you're using, what Application you're using, a full or screen shot of any error messages) the more assistance we can provide, and, the sooner we can provide it..
    Are you connecting to a Cinema display or a New Television set. How are you connecting (HDMI cable, VGA cable, LAN cable, Wireless?)

  • Error when trying to connect on universe .UNX with Query Panel

    Software :
    Windows 2008 Server Standard Edition 64bits
    Dashboard Design 4.0 SP02 Patch 12
    SBOP BI Platform Edge 4.0 SP02 Patch 12
    Hi everyone,
    I'm trying to connect my Dashboard using Dashboard Design 4.0 to an universe with extension .UNX with the query panel.
    I can log on the CMS with an administrator user and I can choose the universe "My_Universe.unx" on the select panel but I try to go to the next step I'm facing of this issue :
    Universe <CUID> not found (XLS 000006)
    The DataSource cannot be generated for the specified dataSource name "<Mydatasource>".
    The integrity of my universe is OK, I use an ODBC 32 bits driver to connect to my dataSource which is a PostGreSQL 8 database.
    I look for a quick answer because this kind of problem is very painful.
    If you want more informations, i'm watching the thread carefully.
    Regards,
    William

    Hi,
    That was already done, that's the first thing I've done but the same error occurs. No matter the CUID of my universe I still get this error.
    I still try to find an answer on forums or sap notes but at the moment, nothing.

  • Trying to connect to apple wireless with my pc laptop

    I am connecting to a apple network(wireless) but can not gain access to internet. I have no problem with hotel wireless networks or my one at home so I know my card is working. cannot figure out why I connect to my friends apple network but when I try email or to gain access to any web site I get:page not found or url not found. any help?
    thanks!

    I went and tried again this weekend to log on going
    thru my friends apple extreme network. still no go.
    tried some new ideas but still have not got on to
    the net. I asked him about wep and wpa. he says it
    is a wep password but is tied into wpa network.
    If he is using WPA, does your wireless adapter support WPA?
    After
    reading the many replys to my posts I went to a
    sight that talks about AirPort Admin Utility for
    Windows. Do I have to have this firmware or is this
    for the administrer? he does not want me fooling
    with his network he polietly told me. Do I need
    this AirPort Admin Utility for Windows?
    The Airport Admin Utility is only used to administer an airport base station, you do not use it for connecting to an Airport network.
    iFelix

  • Trying to connect to Airport Extreme with Dell Wireless 1370 and Windows XP

    Home network using Airport Extreme Base Station with WPA-PSK (TKIP) Security. All works well with MACs in the house (G5, iMac, and Powerbook). Trying to connect a Dell Latitude D610 with built-in Dell Wireless 1370 WLAN mini-PCI Card to the home network.
    Initially home network is not seen on Dell Laptop in available networks (as expected as it has not been added to list of available networks and is a "closed" network)although I do see the neighbors network so card is working and sees "open" networks.
    Set-up options for the Dell 1370 card include:
    Network Name (SSID)
    Network Authentication (Includes "open", "shared", "802.1X", "WPA", "WPA-PSK", and "CCKM")
    Data Encryption (When WPA-PSK is selected it defaults to Auto)
    Network Key
    Confirm Key
    All other configuration items are greyed out.
    I enter my SSID, select WPA-PSK, Data Encryption defaults to auto, tried entering passwrod in Network Key and Confirm Key which does not seem to work. Adds to list of preferred networks but does not indicate availability.
    Question is I have a password that I use on MACs for access to WPA-PSK network. On the Dell there is no spot for a password and it does not seem to work in the Network Key or Confirm Key boxes.
    Any assistance would be appreciated.
    Thanks
    mark
    Airport Extreme Base Station   Windows XP   Dell Wireless 1370 WLAN Mini-PCI card

    Initially home network is not seen on Dell Laptop in
    available networks (as expected as it has not been
    added to list of available networks and is a "closed"
    network)
    Open (broadcast your SSID) your network and see if that makes a difference.
    Often (especially in crowded airwaves) a closed network can cause connection issues for some adapters.
    iFelix

Maybe you are looking for