Nokia N70 starts with a white Screen.

Hi all,
My nokia N70 starts with a white Screen and does not go any further. It does not make any sound while starting. When i connect it to the PC it is not detected by the PC while the phone is on showing a white screen. I have tried performing a Hard reset using the *3 and the green key but it is not formatting either. I also tried updating the software but as the PC is not recognising the mobile connection the updater is not working either. I am using the latest PC suite.
Please help...

Remove the battery for at least 5 minutes and then replace and see if that makes any difference. Also try removing the memory card.
If the above two don't work then try these.Always remember to backup your phone before performing resets as your data may be lost.
First try these
*#7780# - Restore factory settings - resets all the settings to the default 
*#7370# - Reformat your phone
If still not working
Then try the "3 finger deep reset". With the phone powered off, depress and hold these three keys simultaneously "*" "3" "green phone" and then power on phone using the on/off button whilst keeping the three keys depressed until you hear start-up tone.
This should ONLY be done if the device doesn't power up normally anymore and it wipes everything in the Phone memory that is not part of the ROM.

Similar Messages

  • My imac starts with a white screen, then goes black and a small white line just blinks in the top left corner of the screen?

    My imac starts with a white screen, then goes to black with a small white line blinking in the top left corner of the screen. Any ideas? Thanks.

    Try starting your iMac with the original DVD that came with the machine then launch disk utility to repair your hard drive. 

  • Macbook Air starts with a white screen and permanent "poing"-sound...

    Macbook Air starts with a white screen and permanent "poing"-sound...
    Tried SMU, PRAM, MMU resets, but nothing helps...
    Thank you for your support.

    You need to take it in for service, it may be a stuck key or component failure.

  • HP Pavilion dv7 Notebook starting with Blank White Screen--He​lp??

    I've had an HP Pavilion dv7 Notebook for a couple years now. Today I go to start it up (without the power cord plugged in), and a completely white screen appears. I'm thinking, maybe it's still starting up/working some kinks out. Then I hear the Windows 7 twinkling start up sound that usually happens when you get to your log in screen. So it seems the computer itself is working, but there is zero display on the screen. If anyone has any good advice/experience with this/knows how I can fix it or what I should do, PLEASE let me know! Computer problems are so distressing

    I had this problem with my father's pavillion.
    There was a broken pin in the screen socket on the motherboard so I guess it was always making poor contact until one day this pin must have broken off completely and the screen would only display completely white.
    I inserted a fine solid wire (not multi-strand) into the plug at the right point so that it only just stuck out enough to make contact with what was left of the pin in the socket, whilst being fully inserted into the plug.
    I then taped the plug/socket together to make sure it didn't loose contact by coming loose.
    Seems to have solve the problem in the short term (but the socket should need replacing for a long-term fix).

  • Satellite C650D-007 starts with blank white screen

    Hi everyone,
    I need urgent help, I bought this new laptop 3 weeks ago from Futureshop.ca and now today, i pressed the power button to turn it on and when it does i get this blank white screen.
    I even tried removing the batterie and hooking up the AC direct and it still produced the same thing.
    I can't believe after only 3 weeks it stopped working.
    PS: it does power on. just a white blank screen. no logo nothing.
    thanks in advance.

    Hi
    I think Dr.Lamp is right it looks like a hardware issue
    The notebook is covered by warranty so either you will get in contact with an Toshiba ASP in your country and will ask for fix or you will check this with the dealer and maybe you could get a new notebook.
    However, I think such hardware problems can happen always you had simply a bad luck I bought a notebook from other manufacture for my father the notebook died after 3 days of usage :(
    I contacted the dealer and got a replacement.

  • My imac starts up with a white screen, gray apple and spinning gear and is frozen on that screen. What can I do?

    my imac starts up with a white screen, gray apple and spinning gear and is frozen on that screen. What can I do?

    Start your iMac with the original DVD that camera with the system.  Then open disk utility and repair your hard drive, also repair your permissions. 

  • My macbook is not starting properly, remains white screen as it is with apple logo and spinning gear

    my macbook is not starting properly, remains white screen as it is with apple logo and spinning gear

    Hi..
    Your profile indicates you are running Lion v10.7 so you need to use Lion Recovery  to repair the startup disk if necessary or reinstall Mac OS X.

  • Every time I started my Imac, loks like If It is the sistem downloading again, with yhe white screen, the apple and the filling up bar. Its that normal???

    Every time I started my Imac, loks like If It is the sistem downloading again, with yhe white screen, the apple and the filling up bar. Its that normal???

    It is for Yosemite. Not for Mavericks or earlier.
    OS X Mavericks- If your computer stops or delays while starting up with progress bar

  • My Macbook Pro is frozen on the login page with a white screen and only my login picture. How do I fix this? I can't turn it off and I closed it and let it charge but it's still not working.

    My Macbook Pro is frozen on the login page with a white screen and only my login picture. How do I fix this? I can't turn it off and I closed it and let it charge but it's still not working. It's only 3 months old and was working perfectly fine 30min before this happened.

    Hello Kierasully,
    I would start your troubleshooting with the article below for issues of not being able to log in to your Mac. Start with booting up in to Safe Boot as well as resetting PRAM on your Mac. If that does not work, then verify the hard drive with booting to the Recover HD and go to Disk Utility to verify it.
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/en-us/ts2570
    Regards,
    -Norm G. 

  • Start up remains white screen

    During start-up, only white screen with Apple logo...what's happening??!

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.   
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
         a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
    b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 10
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 11
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 12
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • Mac Pro display flickers with a white screen and then display closes

    Hi,
    The display on my Mac Pro started showing a white screen and flickering.
    So I tried formating and re-installing 10.4.10. I am able to complete the installation of first DVD without flickering. But when after the restart after installation using first DVD then the flickering resumes.
    Any idea what is the issue and how we can solve this issue.
    The AHT test shows this code 4 SNS/1/40000001:ICAC. According to
    http://support.apple.com/kb/TS2081?viewlocale=en_US the code should have a trailing number - but my report does not have any number. Is this error code fine? If no, can some one tell me what is the error in the system?
    Thanks,
    Ed
    Message was edited by: esg123

    Same symptoms here. We tried AHT on a good Mac Pro with the video card from the bad mac, and got the 4 SNS/1/40000001:ICAC error. Looks like a bad video card.
    Here's another thread discussing the problem: http://discussions.info.apple.com/thread.jspa?threadID=2071334
    Dave

  • I am upgrading to 10.8.3 snow leopard and it has been 3 hours with a white screen - is it supposed to take this long?

    I am upgrading to 10.8.3 snow leopard and it has been 3 hours with a white screen - is it supposed to take this long?

    Welcome to the Apple Support Communities
    It looks like your MacBook Pro is restarting. Just hold the Power button until your computer turns off, and then turn it on again, so OS X should start properly

  • My ipod touch has frozen with a white screen. None of the buttons will work to turn it off or take any action. Holding down buttons for 10 seconds plus does not work.Help

    My ipod touch has frozen with a white screen. The on/ff and sleep buttons will not work whether pressed for a moment or held for more than 10 seconds as per help pages. When connected to computer it is not recognised and no indication in "devices".It has been working perfectly from Christmas until now. Was watching a TV prog via BBC iplayer when the image and sound froze for about 5 seconds then just white screen. Help

    First, try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."

  • My MacBook Pro shuts down within seconds after starting with a Gray Screen and Apple Logo, a bar comes at the bottom.

    My MacBook Pro starts with a Gray Screen and Apple Logo, a bar comes at the bottom, but after few seconds the machine shuts down. This was bought approx 1 year back. Please help!!

    jayanta.ray,
    which model MacBook Pro do you have (did you buy it new?), and which version of OS X is installed on it?

  • My IPad Air is frozen with a white screen and Apple Logo on it.

    My Ipad Air is frozen with the white screen and apple logo.  I've tried resetting it several times and that doesn't help.  I tried connecting to ITunes, but it isn't recognizing the device. 
    The battery is fully charged, at least for now, so I am not sure what else to try.

    FORCE IPAD INTO RECOVERY MODE
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.
    3. Repeat the process if necessary.

Maybe you are looking for