Nokia N95 Screen Backlight Problem! Please Help Wi...

Its been about 9 month since I purchased Nokia N95. Last night, when I was watching a video, its screen backlight began to flickr. It turned very dim and then restored. It turned again compeletely off, then came to its normal brightness. I tilted the phone in all ways, hto it gently to know whether some wire inside is loose, open and closed the slider. But the screen went on and off itself. I reset my phone by hard formatting (*#7370#) but of no use. The next day, it did the same. After two days, now it is stable. But I fear it might be started again.
I want to know can this problem be due to some moisture inside my phone or is it because of some hardware proble. And please suggest what should I do. My phone is still under warrenty, but the phone is stable for at least a whole day. Should I carry it to warrenter for repair?
Any suggestions in this regard? Please reply with practical experience and not a hypothetical reply.
I appreciate your cooperation.
Ejaz

Hi gilli34
Caps off might be nice.
To include a "smiley" in a SMS (predictive text must be on) just press "1" three times and press"*" to change it to a wink!
You could always look at Animated SMS here:
http://my-symbian.com/s60v3/software/applications.php?fldAuto=314&faq=1
Happy to have helped forum in a small way with a Support Ratio = 37.0

Similar Messages

  • Nokia N8 sim card problem please help!!

    I have been the proud owner of a Nokia N8 for about 9 months now without any problems or issues jus some random bugs...since N8 is a troubled device as we all know. But anyways jus now it has come up with lots of issues...at first my phone started to restart as soon as the phone started up. Even before all the apps loaded up and i tried around 15 times to switch off and start and stuff. But to no avail...so i went on some forums and blogs and got some tips like resetting it by holding down the power button for 8 secs and everything but still the same problem. Now, I removed my sim card and put in a different one and VOILA it worked!!! No restart so I thought maybe the older sim was faulty. but as i put the old sim in another phone...it worked in that phone! I was dumbfounded as the sim was working on my n8 before toO! ......so i just ignored it and i used the other sim in my n8 but not for long after half an hour the phone was not starting up sim card or no sim card. so i flashed my phone to the official Symbian Anna and i tried booting up without a sim card and the phone works properly. but as soon as I put in the sim card and switch the profile to normal mode..the phone freezes for about 5-6 seconds and reboots only to find my phone in offline mode again and same problem. I have tried changing sim cards nd memory cards, reset, reflash, format the mass memory, and everything else possible but in vain. The problem still exists!! Can anyone please help me as Im very fond of the phone and I dont want to send it to the service center as they would come up with some lame excuses + i hav lost my warranty card!! Please help....and btw the phone works flawlessly without a sim card! And also, in offline mode when i switch on the bluetooth...the phone freezes and restarts! Evn the WLAN keeps on searching for network and doesnt find any even though there is! Any help would be appreciated... thank you!

    Just want to say "I dont have my warranty card"
    No official Nokia care point will say this as they can check the warranty satus online using your IMEI number- if they do not do this, either insist they do or report them to nokia care direct and lodge a complaint. (0845 045 55 55 from the UK)
    Even if the warranty has expired online, this can be extended if you can provide a proof of purchase date. This can be a delivery reciept if you bought online, or your high street retailor will be able to provide you with a copy if you ask them- even your original service agreement should be enough. Remember you get a full 2 years warranty with all Nokia handsets. 
    Nokia Care are there to help, not to make things difficult for you. They go through untold amounts of training to ensure you get your handset back as soon as possible in a fully working order. 
    I feel bad you feel such reluctance to contact a care centre, Nokia have gone to massive efforts to provide consumers with this kind of readily available support. 
    If you are in the UK and your local care centre is not helping you I would suggest you call the one i use, they will give you all the advice you need 01242 539539 (i hope giving out this info is ok on the forums)

  • Nokia E61i and iSync problem - Please help!

    I had the Nokia E62 and I was syncing with my macbook pro without any any problems. Last week I got the Nokia E61i and installed the plug-in for the isync from the nokia website. I have been unable to sync the 2 phones. I have deleted the phones from isync and reset the phones but no luck. I have tried both bluetooth and cable. The isync connects to the phone but give me an error message - "An unexpected error occured. Device 'Nokia E61i' synchronization failed"
    Please I need someone to help me resolve this problem.

    This Apple Tech Support Document seems to mention exactly your error:
    iSync: Error message when synching phone via Bluetooth in Mac OS X 10.4.9 or later

  • N95(8gb) Memory Problem (please help)

    Hello
    New here, so I hope I'm posting this in the right area of the board.
    I have recently purchased a second hand N95 (8gb) but having problems with the mass memory. Yesterday, while downloading some tracks to the handset (about 2 hours worth of tracks from scratch), a warning kept appearing on the phone saying that memory was full and that I needed to delete some data. I went to the memory section of the phone and by mistake I pressed the 'format mass memory' thinking it would help, but it didn't. I still cannot put any tracks or videos to the phone. Intotal I have only 18 tracks, some 1 hour 12 mins in length. Clearly something has gone wrong.
    The phones capacity is currently reading:
    Capacity: 7735mb
    Used: 1472kb
    Free: 7734mb
    Hope that someone can assist.
    Many thanks
    Jonathan

    thats fine but i dont konw is this the latest software for this phone my suggestion would be go to nokia.com, before that switch off ur phone and remove ur battery u will find the product code it will start with the numbers "05" note these numbers i think it will be a 8 digit no i am not 100% sure,back to nokia.com u will find a link download software,there u will have an option "can i update" and it will have a box to enter these numbers enter and click "go" if u find a version greater than what u see on the phone go for the latest
    "Sorry for the long description"
    If a reply has solved your problem click Accept as solution button, doing it will help others know the solution. Thanks.

  • Nokia N80 and LifeBlog problem(Please Help)

    Hello
    I bought my n80 a week ago and I bought a 1GB memory card,so I moved all the files from the 128MB memory card to the 1GB memory card,anyways when I switched my mob on I had to install life blog again,but when I try to start the programme it wouldn't start, so I sent the aplication again from the old memory card to my phone using PC SUITE,anyways I just wanted to know whats the difference between those two file:
    LifeBlog_Installer
    LifeBlog
    because when I installed LifeBlog_Installer the programme wouldn't work,but when I installed LifeBlog it worked perfectly, is it ok if I deleted LifeBlog_Installer?

    This Apple Tech Support Document seems to mention exactly your error:
    iSync: Error message when synching phone via Bluetooth in Mac OS X 10.4.9 or later

  • My iPad stop working suddenly i see black screen only pressing the home? and sleep button dose not solve the  problem please help?

    My iPad stop working suddenly i see black screen only pressing the home and sleep button dose not solve the problem please help ?

    Frozen or unresponsive iPad
    Resolve these most common issues:
        •    Display remains black or blank
        •    Touch screen not responding
        •    Application unexpectedly closes or freezes
    http://www.apple.com/support/ipad/assistant/ipad/
    iPad Frozen, not responding, how to fix
    http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
    iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
    http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
    Black or Blank Screen on iPad or iPhone
    http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
    What to Do When Your iPad Won't Turn On
    http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Home button not working or unresponsive, fix
    http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
    Fixing an iPad Home Button
    http://tinyurl.com/om6rd6u
    iPad: Basic troubleshooting
    http://support.apple.com/kb/TS3274
     Cheers, Tom

  • Hello sir my iphone screen turns off after using 2-5 minutes what would be the problem please help me out

    hello sir my iphone screen turns off after using 2-5 minutes what would be the problem please help me out

    To make sure that this is not software related, set it back to factory settings, without using any backup data afterwards. Set up the rest of the personal settings manually and test the phone. If it still does not work, this is a hardware issue and the phone has to be serviced by Apple or an Authorized Apple Service Provider:
    Use iTunes to restore your iOS device to factory settings - Apple Support
    Find an Apple Authorized Service Provider
    iPhone - Contact Support - Apple Support

  • My Ipad 2 does not turn on when not plugged to electricity. Even when plugged to electricity, it constantly restarts/switches itself off. what is the problem, please help??

    My Ipad 2 does not turn on when not plugged to electricity. Even when plugged to electricity, it constantly restarts/switches itself off. what is the problem, please help??

    i plugged it and pressed the home button for a few seconds. the connect to itunes screen appeared and the moment i disconnect the cable from the electric plug, it switches off. when i connect the cable to the PC, nothing happens, its as if nothing has been done.

  • X-Fi Fatal1ty Plat1num Champion Ed. problem, please help!

    9X-Fi Fatalty Platnum Champion Ed. problem, please help!? Hi there everyone,
    So i have a X-Fi Fatalty Platnum Champion Ed. and a computer with Windows 7.
    I've searched the web and i found many people saying that the card it's working and perfectly compatible so i would like to exclude this option as far as the problems that i'm having.
    So, right out of the box i've placed the front panel in with the ribbon cable and the power connected to it, then i connected the other end of the ribbon cable and finally placed the card in one of the PCI slots i have free.
    Now, when i start my PC, i don't hear any particolar "beep messages" but nothing will come on the screen, in few words my PC will not boot at all. I can hear the HDD spinning, everything sounds normal except for that "little" problem.
    So, i re-did all the connections thinking that maybe i did something wrong, but following the instruction i did exactly as told. So i tried again to power up the computer and i've noticed that the X-Fi logo is lit up (red light) and.. I don't really know if that means something or it's just something aside that doesn't really matter.. But, what is it's The PCI card is broken or there's something else?
    I did try to disable the sound card (integrated mobo sound) from the BIOS but that didn't change anything. I did try all the software options but this looks like more of an hardware problem (please correct me if i'm wrong and/or i've missed something).
    There's something that popped up in my mind.. the PSU. I noticed that i have a 300W PSU (mm.. low, isn't it's)?and i was wondering if that's enough or i need a more powerful one.. and if that's may be the case for the PCI to not work at all causing all i've already explained above. I mean.. It seems like i've installed a dead peripheral and that's impeding the computer to start up..
    I don't know.. I need clarification and help, PLEASE.
    Thank you very much in advance!

    Look at the beta thread sticked above but good luck waiting for a new driver. That beta driver has been there since January and although better than the normal driver it is still crap.
    All the boot type issues are with the SSD but if you getting in game crashes etc... under windows 8 that is simply that the driver stinks.

  • Hi .. my iPad 4 with iso 7.0.3 he is restarting himself ... How can i solve this problem please help me

    Hi .. my iPad 4 with iso 7.0.3 he is restarting himself ... How can i solve this problem please help me

    Standard troubleshooting...
    1. Try a Restart by pressing the sleep/lock button until you see the slider.  Slide to power off.  Restart by pressing the sleep/lock button until you see the Apple logo.
    2. Try a Reset by pressing the home and sleep buttons until you see the Apple logo. Takes about 5-15 secs of button holding and you won't lose any data or settings.
    3. Remove apps from Recently Used list...
    - From any Home Screen, double tap the home button to bring up the Recents List
    - Swipe up on the app preview card to remove it from the list
    - Press the home button when done.
    4. If still a problem restore with your backup.
    5. If still a problem restore as new, i.e. without your backup. See how it runs with nothing synced to it.
    6. If still a problem, it's likely a hardware issue.

  • My iphone 5 32 gb has an camera autofocus problem, please help me solve this

    my iphone 5 32 gb has an camera autofocus problem, please help me solve this

    Hi teejayfs,
    Thanks for visiting Apple Support Communities.
    If you've noticed unexpected behavior with your iPhone camera, start with these steps to isolate or resolve the issue:
    Camera isn't functioning or has undesired image quality
    If the screen shows a closed lens or black image, force quit the Camera app.
    If you do not see the Camera app on the Home screen, try searching for it in Spotlight. If the camera does not show up in the search, check to make sure that Restrictions are not turned on by tappingSettings > General > Restrictions.
    Ensure the camera lens is clean and free from any obstructions. Use a microfiber polishing cloth to clean the lens.
    Cases can interfere with the camera and the flash. Try gently cleaning the lens with a clean dry cloth or removing the case if you see image or color-quality issues with photos.
    Try turning iPhone off and then back on.
    Tap to focus the camera on the subject. The image may pulse or briefly go in and out of focus as it adjusts.
    Try to remain steady while focusing:
    Still images: Remain steady while taking the picture. If you move too far in any direction, the camera automatically refocuses to the center.
    Note: If you take a picture with iPhone turned sideways, it is automatically saved in landscape orientation.
    Video: Adjust focus before you begin recording. You can also tap to readjust focus while recording. Exiting the Camera application while recording will stop recording and will save the video to the Camera Roll.
    Note: Video-recording features are not available on original iPhone or iPhone 3G.
    If your iPhone has a front and rear camera, try switching between them to verify if the issue persists on both.
    You can find these steps here:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Regards,
    Jeremy

  • P6N Lots of problems please help

    P6N Lots of problems please help
    The setup is the following:
    P4 D935 3.2gHz
    P6N Diamond MS-7320 Bios 1.3V
    Corsair XMS2-6400C4DHX
    NX8600GT-TD512EZ/D2
    Seagate Barracuda 7200 250Gb SataII 16Mb
    Akasa 460W Dual Rail
    Please help I have lots and lots of problems with lockups that can happen any time post , bios , loading vista and sometimes during OS. Some times will work ok play games etc. Already tried different combinations fitting the mem modules even tried and some pc4200 modules same problems. Spent lots of hours clocking the mems with different settings but non is stable. I am not interested in overcloking just to make it stable to start with. When is actually running is fine is more than enough for me. Already looked to lots of posts on the msi forum but… Since the cpu is old can I go back on an older bios version???? The Corsair modules have to run at 2.1V or is it possible to use them with slower setting. So confused so lost ….. please HELLPPPPP
    Any help greatly appreciated.

    please, don't buy any more unneded parts.  first find the problem then buy if no solutions available.
    One thing I find with BIOS issues is to do a full clear.
    1. disconnect the power cord from the power supply(turn switch to off if there is one.
    2. hit the power switch to clear the power out of the system.
    3. set the cmos jumper to clear and leave there if one is available.
    4. Pull the battery.
    5. carefully short out the battery connector on the motherboard to drain any power left.
    6. press the clear cmos button and hold for 30sec minimum, if you didn't have a jumper to set. 
    7. replace battery, move jumper back, plug in power cord, turn on power sipply switch.
    Now it should hopefully power up.  go into BIOS and load optimized results. hit save and exit and when it gets back to the post screen, go back into bios and set your normal MB settings(ie. set boot devices, boot order, disable sound if using sound card, etc...)
    go into your H/W Monitor section and list the CPU Vcore settings to make sure it is getting the power it needs.  I just looked it up and it's suppose to run from 1.225v - 1.325v.
    also, try your most generic ram you have with auto settings.  the faster the ram usually the more volts they need and default volts are 1.8v for ram and sometimes faster chips have issues with lower volts.
    Let me know how this works for you.
    -=Mark=-
    ps. make sure everything is unplugged from the computer you don't need.  just cpu, 1 stick of ram, and video. and of course keyboad and mouse.  Please make a signature with all your systems specs including make and model numbers.  I hate guessing at solutions and I'd hate to see you buy any more unneccessary parts because of lack of information.

  • My iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: "unknown error (36), i´ve tried to do lot of things but i can´t  solve my problem. please help!!

    my iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

    Hi, i had the same problem. Try to find the file "apple" or "itunes" don't know it anymore exactly. Ahm well you need to delet any information or just plug in your iphone into an other computer. important is that your iphone never has been pluged in this computer before. This was what i did, and it worked!

  • Problem Please help me.....Let me know the area to look for it I am a DBA..

    Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
    Server Error in '/' Application.
    Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
    Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
    Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
    Source Error:
    An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. 
    Stack Trace:
    [SoapException: Problem with SAP/BAPI.
    SAP.Connector.RfcCommunicationException: Connect to message server failed
    Connect_PM  MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
    LOCATION    CPIC (TCP/IP) on local host
    ERROR       service 'sapmsPRD' unknown
    TIME        Wed May 04 08:59:06 2005
    RELEASE     620
    COMPONENT   NI (network interface)
    VERSION     36
    RC          -3
    MODULE      ninti.c
    LINE        428
    DETAIL      NiPServToNo
    SYSTEM CALL getservbyname
    COUNTER     1
       at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
       at SAP.Connector.SAPConnection.Open()
       at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
       at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
       at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type)
       at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
       System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
       System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
       SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
       SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
       SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
       SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
       SoftwareKeyUI.search.LoadRegionDetails()
       SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
       System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
       System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
       System.Web.UI.Page.RaiseChangedEvents() +115
       System.Web.UI.Page.ProcessRequestMain() +1099

    The error is a very basic one - the sapmsPRD service is not known. You will have to go to <NT_ROOT>\system32\drivers\etc and add the entry sapmsPRD 3600 to this file.
    This is basically telling the requester at what port to look for the message server.
    C

  • Problem Please help me.....Let me know the area to look for it

    Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
    Server Error in '/' Application.
    Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable&amp; Kpi_Regions, ZSOFT_PROD_TYPETable&amp; Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
    Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
    Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable&amp; Kpi_Regions, ZSOFT_PROD_TYPETable&amp; Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
    Source Error:
    An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
    Stack Trace:
    [SoapException: Problem with SAP/BAPI.
    SAP.Connector.RfcCommunicationException: Connect to message server failed
    Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
    LOCATION CPIC (TCP/IP) on local host
    ERROR service 'sapmsPRD' unknown
    TIME Wed May 04 08:59:06 2005
    RELEASE 620
    COMPONENT NI (network interface)
    VERSION 36
    RC -3
    MODULE ninti.c
    LINE 428
    DETAIL NiPServToNo
    SYSTEM CALL getservbyname
    COUNTER 1
    at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
    at SAP.Connector.SAPConnection.Open()
    at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
    at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
    at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable&amp; Kpi_Regions, ZSOFT_PROD_TYPETable&amp; Prod_Type)
    at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
    System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
    System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
    SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
    SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
    SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
    SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
    SoftwareKeyUI.search.LoadRegionDetails()
    SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
    System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
    System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
    System.Web.UI.Page.RaiseChangedEvents() +115
    System.Web.UI.Page.ProcessRequestMain() +1099

    Hi
    You should make a mapping for the service sapmsPRD in your /etc/services file (On Windows: C:WINDOWSSYSTEM32DRIVERSETCservices). If your instance number is 00 you will have to add the following entry:
    sapmsPRD      3600/tcp
    Good luck!
    René van Es

Maybe you are looking for