Nokia5800,after upgrading software,phone don`t wor...

hi
i upgraded the firmware to 51 version
everything was completed and the phone shut down
since than, it won`t start again
all i get is a vibrating of the battery for 20 sec and nothing else
any idea what`s wrong?
hard restart don`t work either
thank you

All you can do is posted in the "pool of knowledge" by the superior Psychomania. Read here: /t5/Pool-of-Knowledge/Recovering-from-a-failed-fir​mware-update/td-p/398147
Unfortunately, the hard reset is the last option for end users to do, but the guide will provide you with information of where to turn.
What you could try is to pull out both the memory card and the Sim card. Leave the battery out for about a minute and then try the hard reset (without the memory card and the simcard).
Give it a few shots as it can be hard to get it right the first time. The 3 buttons shall be depressed and hold while powering on (makes it 4 buttons).

Similar Messages

  • I'm still struggling with being able to sync ipad3 and iphone 4s to itunes after upgrading software to ios 6. I've gone through all the recommendations by Apple and suggestions from other forums and nothing seems to work. Help!!!!!

    I'm still struggling with being able to sync ipad3 and iphone 4s to itunes after upgrading software to ios 6. I've gone through all the recommendations by Apple and suggestions from other forums and nothing seems to work. Help!!!!!

    Sounds like you have a battry issue but don't want to believe it.
    If a car was running fine on one tank of gas, then you filled it up with another tank of gas and it began to run funny, one might suspect that tank of gas. But let's just say coincidence blew a valve-- would you think the new tank of gas was the culprit?
    BUT WAIT!! It just might have been! The gas could have been of higher octane and put more more strain on the valves; you know, like going from 87 octane (OS6) to 93 octane (OS7) and showing you the engine was on the edge of compromise.
    Sometimes you have to go with common sense. If everything else is ruled out, it must be the battery. And if it runs fine one moment in OS6 but immediately ***** in OS7, I'd believe my battery was suspect-- though comfy-- in OS6 but the OS7 showed its true power.
    Moreover, if you had the answer-- or didn't want to believe someone's more competent advice-- why did you even call?  You've already shown that you don't know much when you asked if you could go backwards after setting up the new OS as a new phone.
    Additonally, if you're such the know-it-all, but yourself the $29 battery and put it in yourself. It's a piece of cake.
    <Edited By Host>

  • After upgrading i phone 4 to ios 5 , my phone locked for ever .! help please

    after upgrading i phone 4 to ios 5 , my phone locked for ever .! help please

    What do you mean "locked forever"? Was your phone hacked to unlock it? If so, updating iPhone software will re-lock it to the carrier it was originally locked to. If that happened to you, you have two choices: 1. Get it officially unlocked, or 2. Re-hack it to unlock it(help with that can't be provided here). Good luck.

  • After upgrading software on my iphone 5. I am not able to in app purchases. I have tried to turn of the restrictions and it is still not letting me make purchases.

    After upgrading software on my iphone 5. I am not able to make in app purchases. I have tried to turn off restrictions and still not able to make in app purchases. Can anyone help me?

    If there are no restrictions engaged and you are not receiving any Error messages or Alerts...
    Contact iTunes Customer Service and request assistance
    Use this Link  >  Apple  Support  iTunes Store  Contact

  • After upgrading software microphone doesn't work

    After upgrading software microphone doesn't work

    Dimitrios44-
    Have you tried using the microphone with more than one App?  One I use is Skype, which is a free App.  Once your are registered with Skype, you can use their test server to record and playback several seconds of your audio.
    It may just be coincidence that your microphone stopped working after the upgrade.  If you show it to an Apple Store Genius, you may get a new iPad.  If that is not convenient, search for an Authorized Apple Repair Center near you.  There may be one in your city.
    One thing you can try is to reset (reboot) the iPad.  Hold both the Home and Sleep buttons for several seconds until the Apple logo appears.  Ignore the "Slide to power off" arrow.  The iPad will restart after a couple of minutes.  Resetting this way will not hurt anything, and sometimes clears up mysterious problems.
    Fred

  • After upgrading software to 5.0, I lost my Contact List. How do you retrieve it.

    After upgrading software to 5.0, I lost my Contact List. How do you retrieve it.

    Prodesigntools.com , go ahead and download the software from there and use your serial number to serialize it.

  • I have a problem with my iphone,after upgrade software ios 6.0.1,  is not possible to use the wi-fi, used until now, because is not possible to have the login, i find this message " the requested URL  was not found

    I have a problem with my iphone,after upgrade software ios 6.0.1,  is not possible to use the wi-fi, used until now, because is not possible to have the login, i find this message " the requested URL  was not found

    You have to go to autherized iPhone agent.

  • The location services on my MacPro don't work after upgrading software

    AFter upgrading to OSX 10.9.5 on my MacbookPro from 2013, I cannot make Location services work. It's turned on in "Settings>Security &Privacy enabeling Maps, Calendar, Safari and Evernote. what can I do?

    You can try the following:
    1 Udate all the applications on the app store
    2 Creat a backup and do a restore
    3 figure it out which applications are failing, by removing them and reinstalling them they should work again
    Probably the most secure woudl be #2
    Good luck!

  • Lost 3G signal after upgrading software

    Hello,
    I have nokia N70 phone with Vodafone UK contract. two days ago I upgraded my phone software from nokia website. All upgrade went smoothly. But now I have lost my 3G signal all together ( I used to have max 3G signal before ).
    When I go to manual network selection it shows all other networks with 3G symbol next to them except vodafone which shows normal signal symbol.
    *#0000# on my phone now shows
    V5.0609.2.0.1
    01-03-06
    RM-84
    I am confused, please help
    Thanks in advance
    Regards
    Amit

    Hi,
    I have an E60, and thought I had the same problem when I saw this post.
    Its worth checking that you have dual mode selected in the network settings. After the update, mine was set back to GSM.
    I had to do a manual connect to the Vodafone 3G network, then able to put it back to automatic, and all is now ok.
    Dave -
    Phones:3110,5110,6110,6210,6310,6310i,8210,8250,8310,6230,6230i,6280,E60,E65, 5800, N900
    and: 7110,6250,6220,6111,7370 (but just for a few months)

  • Authorization problems after upgrading software

    I seem to have some sort of mismatch between the iPod and iTunes with respect to computer authorization. And when I try to authorize this computer, a messags states that this computer is already authorized.
    Background: My young son connected our iPod to his computer, where (I think) there is no authorization. Next time I tried to sync it on my own computer, iTunes displayed a message that the iPod was corrupt and I should try to restore it. When I tried that, I got a message, "The iPod ... could not be restored. An unknown error occurred (1415)."
    Instructions on this website said I should try upgrading iTunes and rebooting, then try restoring again. I did so, with the result that I got the same error message except with error number 1418.
    Other instructions said to make sure the iPod was fully charged. So I charged it overnight and, weirdly, now it seems to be fine. (I didn't even have to "restore" it.)
    Except now every time I try to sync, I get this message: "This computer is no longer authorized to play purchased items that are on the iPod ... Would you like to authorize this computer for items purchased from the iTunes store? ..." So I click Authorize and apparently succeed.
    But then I got another message, saying that a specific song (purchased yesterday) "was not copied to the iPod ... because you are not authorized to play it on this computer." DOH!
    So I go back to iTunes and select Store -> Authorize Computer. But it says this computer is already authorized (which of course it was). But I still can't sync that new song with the iPod mini.
    So, as I said, there seems to be some sort of mismatch between the iPod and iTunes with respect to which computer is authorized. Yet when I try to authorize this computer via the iPod message and via Store -> Authorize Computer, both say that this computer is already authorized. Infuriating.
    Any suggestions? Please?

    I had a similar problem with iTunes when I upgraded to the new 7.5 version. I didn't upgrade my system software or hardware, but I found the Article: 306424 helpful. My problem was with some music that I had purchased with an older Apple ID. I went to the Apple "password recovery" webpage to reset my password for the songs that wouldn't play using the old ID. It worked fine.
    If it is any consolation, I am an experienced Mac technician and I am very religious about maintaining my system so that upgrades and updates to software go well. I'm not saying that you haven't maintained your system, but you may want to "repair permissions" using disk utility. I find this step very important to do before and after any software installation or upgrade. I hope this reply helps in some way and best wishes on solving your particular issue.

  • Blackberry Bold 9700 problem after upgrading software

    i downloaded the 6.0 software on my blackberry and after that it wouldnt let me connect my email account to my phone. so inrder to do that i had to download this app, forgot the name, but once it downloaded the phone needed to be rebooted, after that my phone wouldnt restart and takes about ten mins with the blackberry logo in the front after this a list of all my app are shown with an ERROR STARTING, NOT FOUND. What can i do?

    Hallo Mike und willkommen im Forum!
    Dieses Forum ist englischsprachig, Du müsstest Dein Anliegen noch einmal auf Englisch formulieren.
    Falls Du des Englischen nicht so mächtig bist können Wir Dir vllt in einem deutschen Forum wie http://www.blackberry-forum.de weiterhelfen.
    feel free to press the like button on the right side to thank the user that helped you.
    please mark posts as solved if you found a solution.
    @SimonHain on twitter

  • Blackberry Map Missing after upgrading software!!!

    I have just upgraded my phones device software to 4.5.0.52.  However I now seem to missing Blackberry Maps from my applications.  I tried to remove and reinstall it via Desktop Manager but this has not worked.
    Can anybody help.
    Thanks

    What carrier are you using ?
    I know in the UK Orange no longer supports Blackberry maps 

  • HT1414 after upgrade my phone did not backup

    I lost all my iphone 4 info after upgrading on Itunes..My computer is running windows 8...

    What do you mean you "added your account from there".... You added your account to what from where?
    You are going to need to slow down and give us a blow by blow. We get that you restored your phone to Factory Settings. Whose iTunes library are you downloading information from? Who is signed onto that iTunes library? Who made the purchases that are being downloaded from that iTunes library?
    At what point in the process is it asking for your Aunt's password? What exactly is happening when it asks for it?
    We cannot see your computer or what you are doing, so we have no clue what you are talking about unless you provide us with full details....
    GB

  • I cannot activate the phone now after upgrading software

    I have an old phone, 3GS that I no longer use and wanted to use for my kid.
    I had to update Itunes so I did that.
    When i connected the 3GS which is no longer being used as a phone (but it is unlocked for any provider was using Tmobile) it asked me to update the software before I could move over the apps I have purchased on Itunes to the device.
    So I did so and then when it went to restart it made me go through the activation steps and just keeps saying that activation sever is temp unavailable??

    You might be interested in visiting this thread which discusses a similar problem: https://discussions.apple.com/thread/4673269

  • Brand new IPOD Touch Apps no longer work after upgrading software

    I got a Ipod touch for my wife Today at Wal-Mart. I brought it home, connected to wifi and downloaded some apps and also payed for some. They all worked fine. Then I connected to computer to transfer songs. It told me to upgrade the Ipod software so i Did. After it restarted none of the downloaded apps work anymore. I have read MANY MANY MANY discussions on this and there is no fix. I am not wiping out all the songs and reload everything all over again. It will take forever. My wifes BD is Friday and this is making me so mad after I just dropped $300 on this thing. APPLE!!! Where is the fix? I deleted the apps and reinstalled they still don't work. Anybody got this figured out? I am getting ready to get my money back and tell everyone to avoid buying ipod until they get this upgrade bug fixed.
    Message was edited by: 2009 IPOD TOUCH

    I have the same problem. Brand new two days ago. I synched the touch with Itunes but wasn't hooked up to the internet at the time so didn't do the software upgrade right away. Then I downloaded about a dozen apps (free and paid) with wifi directly to the touch. They all worked fine. Then I plugged it back in to Itunes and had it upgrade it to 3.1.2. It locked up Itunes several times since then and the downloaded apps no longer work (they start to open then disappear).
    The problem is, no one is listening to this problem (including Anna above)! Everyone says "just do a hard reboot, or restore to factory settings, reload the apps, etc." I've tried all the standard troubleshooting but none of it fixes this. It sure seems to me this is a problem with 3.1.2 but Apple isn't helping out here. Where are you APPLE? Use some of those outrageous profits you're making to fix the problem you have created. Here's $300 of my hard earned dollars pretty much down the drain.
    Message was edited by: IPatronius

Maybe you are looking for

  • ISetup Load failures

    I'm currently looking at utilising iSetup to load data from Oracle DRM to maintain our CoA Value Sets. I'm trying to establish what other organisations do in the event of a DRM extract (or other 3rd party extract) drastically failing when loading int

  • Aperture 2.0 vs LR 1.3

    Tethered support for ALL supported cameras.... Lightbox.... Loupe.... Softproofing..... much better shadow/highlight recovery AND an extra highlight recovery which is amazing much improved sharpening/NR and much improved conversions in general 16bit

  • WAD  Dynamic Tabs

    Hello BEx Experts, I have a template and a wad container tab. Wish I could move from first to second tab using a button. Is it possible? Best Regards Massimiliano

  • I think theres a problem with my ram someone help me please

    I have a ibook g4 mid 2005 model and the hard drive says zero kb free i deleted half of my applications i dont need and it still says zero kb free. is there a problem with my ram? or is there a mac virus or somthing? also when i opened a game after a

  • How do I view what I have stored on icloud

    How do I view what's stored on icloud