Nomad Jukebox 3 CarMode isn't functioning correct

It works when I use it in a short while. Such as like. I turned it on, by doing what I call a "Battery Reset". I'll explain what that is later. When I turn the car off, it will do the ShutDown mode, and then when I turn it back on within 5~0 minutes, it will reboot when it regains power. But when I keep it shutdown from the turnoff for more than 0 minutes, I have to do a "Battery Reset".
A "Battery Reset" is when I take both batteries out, and then put them back in, to get the player to reboot.
Is it because I have 2 batteries, that it's giving me this problem? I have a PSP Car Charger, which uses 5Vs; same as the regular charger.
(I had to use the Jukebox's charging unit to charge my PSP, when Sony's POS charger failed on me. I gotta say, Creative did a kick-ass job making it.)
Anyway. I can just turn the Jukebox on manually, but that defeats the purpose of Car Mode.
I have the firmware that was released in 2003. Is there a more later firmware than that one?

I have similar problems and it is very disappointing. I have just tried to start using the Jukebox3 it in my car and it really is kind of worthless at the moment. I have found the following:
) With the battery installed in car mode it shuts down properly. When I turn the car on again it locks up and like you I have to remove/reseat the battery to get it to turn on again. I have found that if I turn my key to the ACC position and pause for a second the player doesn't seem to lockup but it is not feasible to remember this every time.
2) If I remove the battery I don't have any lockups but the player doesn't store the current playlist (I guess it uses the last one used when the battery was installed). So, if I turn off the car for a second I have to reselect the music I was playing. Rediculous.
What a waste the "car kit" has turned out to be. I can't see any way around these problems. I have the latest firmware. Did Creative actually test the player with the car kit in an actual car?

Similar Messages

  • Nomad Jukebox Zen Xtra 60GB not playing correctly anymore, help!!

    Thanks. I keep getting directed to that knowledge base page, but it is not addressing my problem. My computer immediately tells me that the device has "malfunctioned" and the computer does not recognize it. I only have the usb cord that came with the zen, so I don't have another one to try. I love my zen and have staunchly defended it over the years vs. an i-pod. However, this is my 2nd onI've had my Nomad Jukebox Zen Xtra 60GB for over 5+ years. It has worked great, with minimal problems. I had a firmware update issue quite a while back. I'm not sure how to resolve this problem. Here is the situation:
    Nomad Jukebox Zen Xtra 60GB is fully charged and ready to use.
    I tried loading a set playlist but it won't load. So I tried another, and it doesn't load. Not sure what to do, I go to the menu. This time I choose an artist/band. The music loads, but it doesn't play. I try again, then it starts to play. So I load a few other artists that way. It seems like I had a issue to work out later. Being away from my computer that was going to have to wait. After some time the Nomad Jukebox Zen Xtra 60GB started to start N stop diferent songs. A few times it froze while playing a song. Then would unfreeze to play another, then suddenly start playing the previous one. After about 0-5 minutes of this I decided I had enough. So I planned to empty the playlist, and turn it off. It took me atleast three attempts to empty the playlist and turn it off.
    Are these problems fixable What are they hardware or software
    Would an OS or firmware update fix these problems Is my Nomad Jukebox Zen Xtra 60GB hard dri've going Can I get a replacement Or do I need to buy a new player
    Please help me get my player working. I really like this model, I'd hate to have to replace it.
    in 5 years. (The first one fried itself, but fortunately was still under warrantly.) Sadly, I, too, am considering moving on. I onlyreceived generic help fromthe Creative SupportTeam (who ultimately told me my zen is "unrepairable" when their one-size-fits-all solutions didn't work).Since there seems to be an overwhelming # of people experiencing similar problems, maybe the time is right to make the change, especially since an iPod classic 60 GB (7th Generation) is quite affordable these days.
    [/B]

    Formatting will erase all the files on the player,Cleanup scans the disc & corrects file system errors,broken links (from when you delete things)ect. but does NOT repair bad sectors,Reboot then rebuilds the file system. I'd do the Cleanup>Reboot first to see if that solves the problem.here you will find how to open the player to see what dri've is in there. You can then search Ebay or Google the model number to find another one.

  • My brand new iPod Touch 4th Generation, just isn't functioning correctly.

    Recently, I bought a brand new iPod 4th gen. Since, it has gone haywire and refuses to function correctly. It is 16 gb and operating on iOS 6.0.1. On many apps, especially games, it can get really laggy at times, for no discernable reason. I have very few apps installed, and a great internet connection, so I can't understand why that would occur. Also, Safari is absolutely useless. When opened, under any circumstances, It goes to a default white screen:
    Then it can do NOTHING else. Upon further inspection, this seems to happen to a couple default apps. Such as:
    -Calendar
    -Maps
    -Mail
      After about 20 seconds of blankness, it then force-closes to the home screen. In addition, Game Center has become a pain in the butt; it just won't leave me alone. Anytime I try to open a game with internet capabilities (ie.Vector,The Sandbox, etc.), it pops up wanting me to sign in, yet it wont work. When I try to sign in, it never works the first time. I have to home-screen, then click the app again to open it up to the same page, before it even shows the keyboard, not to mention, at this screen, the keyboard is horizontal (landscape) while the rest of the screen is vertical (portrait). From this point, signing in does nothing, it will bring up the buffering circle and spin for about 10 minutes, before promptly force closing. I can't get out of that screen either, when it comes up asking for my log in, the cancel button becomes absolutely worthless, it does nothing. I've disabled Game Center's notification and changed it's capabilities, but it STILL comes up when I try to eneter a game. The only way around it is to completely TURN OFF my Wi-Fi. Thus rendering a lot of in-game content worthless. Lastly, sometimes the Game Center opens Safari, but since it doesn't do anything, I have no idea what to do. Home-screening does not work, as less than a second later, Safari opens again, and again, and again. The only way to stop this annoying cycle, is to completely SHUT-OFF my iPod.The iPod is only a little over a week old, and it ****** me off that I already want to put it down the disposal.

    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup. See:                                 
    iOS: How to back up           
    - Restore to factory settings/new iOS device.
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar          

  • Firefox isn't functioning correctly

    Since updating to Firefox 23.1 (whatever the latest is) Firefox just wont function correctly. The add-on manager doesn't load correctly and states that my system requirements aren't met for firefox, yet it certainly does and has worked previously before.
    I have uninstalled, deleted remanets and reinstalled firefox numerous times to the same effect. I have also done the same with Java, believing this was causing the problem.
    At the moment I am just buggered? No idea why firefox wont work correctly?

    Can you try reinstalling 23.0 to see whether that works? This would help in determining whether it's something specific to the .1 release or whether it's a coincidence.
    Generally speaking, you shouldn't lose any personal data in this process, but it never hurts to make a backup of your profile folder(s) before dropping down a version.
    * [[Back up and restore information in Firefox profiles]]
    * The download for U.S. English is here: [https://ftp.mozilla.org/pub/mozilla.org/firefox/releases/23.0/win32/en-US/] If you prefer a different language, click Parent Directory to find it.

  • Keyboard isn't functioning correctly, can't get into my computer

    Hi there. A few days ago my keyboard started acting very strange. For example, when I push 'D', nothing happens. If I push it 5 times, a bunch of random letters show up. I stupidly shut my computer down and when I turned it on again of course I had to enter my password. Well, this is impossible since my keyboard doesn't really work. My question is...Is there a way that I can see my password as I'm typing it instead of the dots? That way I can figure it out. Thanks!

    Do you have a wired keyboard you can use or borrow as I think you will need one to get the BT keyboard re-connected? Any wired USB keyboard should do for this.

  • TS2634 iPad Smart Cover sleep mode isn't functioning when top lid is closed, iPad still on.

    Smart Cover isn't functioning correctly.  When lid is in place I can still see my iPad on with screen light.  No click sound after lid is place also.  I have remove the Smart Cover and fitted it to my iPad but still Smart Cover sleep mode is not working. 

    Go to Settings>General and make sure the switch to iPad Smart Cover On/Off is set to On.

  • Zen Xtra Nomad Jukebox suddenly not recognized by Windows XP Netbook

    I'm desperately struggling to get my Creative Zen Xtra Nomad Jukebox MP3 player (version .03.02) to be recognized by my computer. (My background is I'm about 4 hours south of my home, temporarily helping my exwife who is slowly dyiing of cancer... [URL"http://www.youtube.com/watch?v=wA67hNO3H4"]http://www.youtube.com/watch?v=wA67hNO3H4[/url] I have two laptops with me, one with XP (and the other rarely used here with Vista.) My main computer, a Dell Desktop running XP, is back at home with most everything else as I live out of a suitcase and do the best I can.... 'nuf said for my situation)
    About 3 weeks ago, I hooked my Creative mp3 player up to my MSI netbook, (windows xp and recently updated with all microsoft updates) and noted that the MP3 player was not being recognized by the computer. When plugged into the USB, my computer gave a 'chirp' and would look for hardware for the player, but ultimately it couldn't find it. The DEVICE page of the SYSTEM menu had the Jukebox listed with the nefarious yellow question mark. Though I don't have a CD drive on this computer, I had a portable drive with most of my software with previousl loaded software archived there, including the installation disc for my MP3 player; but none of the drivers or software that I loaded would make a difference. I download all sorts of drivers & firmware updates from the CREATIVE web site, nothing changed. I would remove all the creative software, reload, reload software, hook up the MP3 player, and.... it would recognize the Nomad player but have no way to incorporate drivers for it's use. Even as I directed it to the original 'CD' copied onto my netbook's desktop, my Windows XP with service pack 3 just couldn't do more than let me know that it couldn't quite recognize the player other than identifying what it was.. I could uninstall the device, the drivers; all to no avail.
    My incorrect guess at the time was that something internal to the mp3 player was broken and though I was lucky that it still worked as a player without any issues, I just had no way to access the 30Gb of books & lectures. Nor would the Creative Media Source work with it, as it felt that the player was not even hooked up to the computer. So,I bought a new 'used' identical model on ebay, except that the seller had upgraded the firmware and the harddrive. Once I got the new player, it's too, would not be recognized by my MSI netbook. (though it works on the laptop I have running vista).
    Last week I gratefully went home for one day to check my mail and attend to a few matters, and upon hooking my original MP3 player to my main desktop, my original MP3 player immedately docked to my computer and was working as it always had?
    Now, atleast, I knew the MP3. player was working and functionally intact, and the challenge was completely computer software issues on my netbook, possibly due to some service pack upgrade or the sort.
    I've spent several hours, reviewing all sorts of fixes and maneuvers; from blogs and tech support pages, though none made any difference as I changed various settings or softwares on my netbook. I saw lots about Vista not supporting my old firmware (which isn't an issue as my Netbook is XP.. I also saw that Windows Media player might have been the problem, and reverted to WMP 9, then to 0, though stlll no change.
    I have never turned to a tech support board before, but I'm very much in need of assistance right now. Please, if you think you can guide me, I would appreciate it.
    ~Stuart

    Thanks for the reply. I sure wish I had a better understanding of this. I will request one more piece of invaluable knowledge from you! My old zen & windows xp computer hum in awesome performance again. Unfortunately, since I thought my old zen was broken, I'm now with this new beast, with the updated firmware 2.0.03. From what I previously read on Boards and Forum pages, this device shouldn't be connected to my XP computer while I'm still using my OLD zen with old firmware. As you mention in the above note, I connect this 'new' Zen to my Vista computer, & it immedately goes into docking mode. I tried loading the newest firmware available for my device (though it doesn't list vista as compatable), and of course, when the mediasource version 3.30.2 loads, it doesn't have a clue that my zen is connected. Only WMP version seems to pay attention, which may not be that bad. But once I was up & running in WMP, I couldn''t seem to create playlists and or even clearly get it to load the Audio Lectures that I have onto it. So, Wise, All Knowing CREATIVE Wizard, any suggestions what I do? Delete WMP? I will hope never to bother you again, once this is solved!!!
    But I am tremendously grateful for the assistance. I only spent about an hour in WMP accomplishing nothing, before I realized I should just turn to you, admit my defeat, and hope for insight and practical advice!!!!!
    Thanks!!!
    ~Stuart

  • NOMAD Jukebox Zen Xtra file recovery from working harddri

    My USB port on my NOMAD Jukebox Zen Xtra is basically non-functional. The drive works fine so i'm not trying to recover "corrupted" files, just ones that exist on the drive... Is there any way I can access the files on the hard drive directly if I remove it from my Nomad Is there any way to use a hard drive connector (from a USB case) where the board plugs into the drive and the other end connects via USB to my computer (which has my Nomad software on it's) As the USB connector on the Nomad isn't working, is there any way i can get my music off the drive
    Thanks!

    Does this happen with all tranfers or any certain audio files? Have you try reinstalling the driver or try running Cleanup in Rescue mode.
    JasonMessage Edited by Jason-CL on 09-04-2006 04:46 PM

  • Windows 7 Support Nomad Jukebox Zen Xtra

    I have a Nomad Jukebox Zen Xtra MP3 player. The hard dri've crashed on my old computer ( which used the wiindows XP operating system). I bought a laptop which uses Windows 7. I don't seem to be able to find a way to access the MP3 player with the windows 7 computer. I don't need?a lot of functionality. I would be happy to put tags on MP3 files with some other software, if only there was a way to get this laptop to talk to the MP3 player. Any suggestions?
    Thanks,
    Ed

    If you can find a PC running Windows XP with Windows Media Player 0 installed you can install the?Creative Zen Xtra PlaysForSure Firmware 2.0.03 - this will turn the player into an MTP device so you will not need to install any special drivers/software to copy music or other files to it (as long as the computer has Windows Media Player 0 or later installed - so Vista or 7 will be fine, as will up-to-date versions of XP).
    I could not get the firmware installer to work with Windows Media Player installed on XP (it claims the player is not plugged in) but Windows Media Player 0 works reliably. As Windows Vista comes with WMP and Windows 7 with WMP 2 you'll need to find an XP machine to install the firmware, though once installed you can use the player with any modern OS.
    As I run Vista on my PC I had to resort to installing XP in VirtualBox to run the firmware installer but I would strongly recommend trying to find a real PC before resorting to emulators!
    Edit: If possible, back up your files before updating the firmware - if I remember correctly updating to the PlaysForSure firmware does delete all of your existing files, but even if I haven't remembered correctly it's worth doing just in case..!

  • Nomad Jukebox Zen Xtra stops working with XP following Windows Media Player 11 Beta Installat

    Yesterday I was very pleased to find that my Creative Zen Xtra (model DAP-HD00) portable media player is a PlaysForSure capable device. Creative Labs, on November 9, 2005, released the Creative Zen Xtra PlaysForSure Firmware v2.0.03. I installed this firmware (I had to install the Creative ZenJukebox Driver v.30.03 first to get Windows to recognize the device). Once the firmware was upgraded, Windows began recognizing the Zen Xtra as a MTP device and life was good. I was able to synchronize it with both Napster To Go and Windows Media Player 0.
    After this, I went ahead and installed Windows Media Player Beta, which I just downloaded yesterday as well.
    From a functional standpoint, WMP seems to run just fine. However, when I connected the Creative Zen Xtra (with its PlaysForSure firmware), Windows redetected the hardware. It first showed "Creative Jukebox Zen Xtra" in the tooltip, followed by "MTP Device" in the new hardware tooltip. Finally, Windows announced that there was a problem installing my new hardware and that it may not work properly.
    Sure enough, when I went into Device Manager, my Zen Xtra was showing as an MTP Device with an exclamation point on it. More specifically, it specified the status of, "This device cannot start (Code 0)."
    Prior to the installation of Windows Media Player, the Creative Zen Xtra showed in device manager with the following characteristics under the heading "Windows Portable Devices":
    Name: NOMAD Jukebox Zen XtraDriver Version: 5.2.0.0 dated 8/30/2004Digitally Signed by Microsoft Windows Component Publisher
    Driver File Details:C:\Windows\system32\wpdusb.sys - v5.2.3802.3802 built by dnsrv(bld4act)
    Windows Media Player changed this to the following (the device now shows up under "Portable Devices"):
    Name: MTP DeviceDriver Version: 5.2.5326.4762 dated 2/22/2006Digitally Signed by Microsoft Windows Component Publisher
    Driver File Details:C:\Windows\system32\wpdusb.sys - v5.2.5358.4827 (WMP_.060509-2009)C:\Windows\system32\DRIVERS\wudfrd.sys - v6.0.5348.0(winmain(wmbla).0604-339)
    The file wudfrd.sys is NOT digitally signed in this case.
    As of now, my Zen Xtra is completely unusable on this system, and I need to sync it with my laptop for the time being, which still has WMP 0 installed on it.
    Is this a bug with WMP beta? Is it a problem with my firmware? Since this is PlaysForSure compliant firmware, and it worked flawlessly with Napster and WMP 0 (before the MTP driver was updated), it would seem to be a WMP beta issue. I'd like to hear more official confirmation on the subject, however.
    Some general details about my system are:
    Microsoft Windows XP Professional with Service Pack 2Verified GENUINE Microsoft operating system using Genuine Advantage ValidationIntel Pentium 4 CPU 3.2 GHz, Hyper-Threaded processor2.00 GB RAM
    Windows Media Player Version: .0.5358.4827Napster Version: 3.6.0.7 (US)
    Any recommendations? Fixes? Some have suggested rolling back the WMP installation, but I would like to consider this option only as an absolute last resort.
    Best regards,Matt

    Ok, this worked out accidentally - but happily
    I first installed the driver - not the media source - but the driver for the device.
    After that the windows device manager yellow sign disappeared - apparently the device driver was registered by windows.
    Then I Installed Mediasource 5 - the installation went thru fine.
    Does anyone have any recommended updates to install, please also advise what benefits.
    Thanks.

  • Nomad Jukebox Zen Xtra as Mass Storage Device?

    I found an old Nomad Jukebox in my closet and seeing as its pretty obsolete im wondering if there are any firmwares that will allow this to function as a plain usb dri've instead of only being able to sync with specific software.
    http://ecx.images-amazon.com/images/I/4KTKWNZNDL.jpg

    nosmokingbandit wrote:
    Probably Windows 7 more than anything else, but the main reason i would like it to behave like a mass storage device is so i can plug it into my car stereo via usb and play music from it. Sure, i could use the auxillary plug, but i find it easier to navigate to a song using my headunit's controls than the Jukebox's.
    Well since that is how you want to use it you could always remove the hardri've format it & use it in a portable hardri've enclosure.Your car stereo does it read an MTP device? What make & model is your car stereo? Do you have access to a XP/Service 2/WMP0 computer?

  • Nomad Jukebox Zen Xtra connection probl

    Hello Everyone.
    First off, I am using Nomad Jukebox Zen Xtra (30G) with Windows XP - SP2. A few days ago my Zen Xtra would connect to my pc but as of today it no longer does. After searching through similar posts I am assuming it's not a problem with my Zen but with my PC. None the less, I did do my best to troubleshoot myself. I downloaded all possible firmware/drivers from Nomadworld.com. However - the firmware upgrade would not complete due to the fact that my device is not connected. I tried connecting my player to other USB ports on my PC - no luck. I used Nomad Explorer to do my transfers and as suggested in the FAQ, I tried downloading others (ie: MediaSource) however these wouldn't install because it could not detect any device. When I go to Device Manager/USB/ my Nomad isn't even listed. I have tried 3 different USB cables. The player isn't locked. Other devices work with the usb cables and port (ie: logitec clicksmart camera)
    So now assuming it is a PC problem, where do I go from now? Thanks in advance for any help you can give me

    Hibbs,
    Thank you for your response. The only thing that comes to mind is k-lite codec pack I downloaded and installed for the Indeo codec needed for my clicksmart 820. I'm not sure if that would have anything to do with the disruption of my device. The camera itself worked but wouldn't record videos until I installed the codec. Everything else to my knowledge is the same. No other new USB devices installed either.

  • Nomad jukebox zen xtra - cannot create file w message when trying totransfer fi

    My 30G nomad jukebox zen xtra was working great until recently. Now when I power my player up after a day of no use, it takes 0-5 minutes to rebuild the library. When I begin to transfer files using Media source after a few transfers I get the "unable to create file" message and can no longer transfer. I have tried disk clean up and re-booting to no avail. I tried installing the new firmware and this worked for about 80 songs and then I began getting the same problems. I have completely cleaned my PC of adware and spyware and this has no effect. I love my player but am becoming a little frustrated. Would anyone have any ideas? This all started when I turned on my player one day and all of the music was gone. I re-transfereed everything back and later noticed that I had two of everything. I deleted all of the duplicates and from that point on it began to take 5 minutes to rebuild the library but I could still transfer files with no problems. One last thing, when I run disk cleanup in rescue mode, once it gets to 99% done it stalls there for about 0-5 minutes before going back to the rescue mode menu.
    scott

    i experienced the same problem. until 2 weks ago it worked fine. but a visited the support site and found out that all the software was new. so i downloaded the new versions. even the new firmware with the e at the end. i was at the edge to smash my monitor when i found out that after the firmware update the sound was hearing so quiet. after rebuil os and searching 2 hour on the net for the previous firmware release, prior to E release, i solve the sound problem.
    but another appeard. cannot copy files on the player. if i choose to delete them, they disappear. i turn off the zen nx, turn back on and the files were still there. practically all the copy/delete/new folder/paste function were blocked. and the same problem on WIN XP and win 2000. all this because i installed the new versions for nomad explorer, nomad mediacenter, nomad plugin for media center.
    solution: uninstalled all the creative software. put the original cd in the dri've. installed all the original software. it was running perfect. so, i could operate again in the data files on the player.
    so i thought it was the driver problem since the media library i could access just fine. so i kept the original driver but installed all the new software (mediasource, nomad explorer, nomad zen plugin for mediasource).
    guess what? the accesing proble appeard again. i think that the better solution is to stick to the original software.
    and one last find. after the E firmware adveture, i experince what other are and was praing not to happen to me. the battery is lasting much much short period. and the green light if you look carefully is fluctuating in intensity. this was not happening until i burn the new E firmware. .0.02e. now after the rebuild os and writng a firmware it displays .0.02 without the E. the sound is like before. 24 damages your ears but the battery problem stills persit. it driving me crazy.

  • No power after firmware upgrade on nomad jukebox zen xtra

    I have the nomad jukebox zen xtra 30gig that froze up over a year ago after i tried to install the firmware upgrade. After the unsuccessful attempt, the mp3 player stopped working.... I mean no power at all. I've changed the battery and recharged the battery from an outside source...still no luck. I can't even try any of the suggestions anyone gives on this site because I have no power.Does anyone have this problem? More important, does anyone have this problem and know of a solution?I've already set my pc back to wmp 0, I have the firmware on the desktop waiting. Now all I need is some power on this unit so that i can try some of the suggestions that seems to be working for people. Thank you

    I have the same problem too, but my unit is a?Creative Normad Junebox Zen Xtra 40GB. I was trying to find a solution to my problem when I read about your problem. I have pressed the reset button, on / off switch, removed the battery, reinstalled the battery, and nothing seems to work. I was hoping you?might get a solution to this problem, so that I might be able to fix my MP3 player. If I hear of a solution, I will let you know, thanks for sharing. Issue:? While updating the firmware to the Zen Xtra 40 GB, the unit powered down and?has never came on again. There seems to be no real reason why the unit should not power up. The battery and the AC adapter are working correctly. I am very disappointed in Creative...

  • Touch vs. Nomad Jukebox (yes, the ORIGIN

    I am getting antsy and bored waiting for the Touch firmware to be released. I was looking for a game and saw my good ol' reliable blue nomad jukebox sitting on the shelf. I gave it good hug. For over fi've years that CD-player sized original HDD based MP3 player has gone everywhere with me. Until a few weeks ago when i bought a Zen Touch.
    I scoured the net, comparing the Zens to iPods to Rios to Ri'vers. In the end, my personal experience (happy ) with creative made me choose the Touch in the end.
    Everyone likes to compare the Touch to the iPod, calling it the "iPod killer." Well let me tell you something, oh my brothers, that overweight blue monster with its 6 hours of battery life is the Touch killer. Hell with why the Touch is better then the iPod, lemme tell you why the Nomad Jukebox (C, or DAP as you care to call it) is better than the Touch:
    My current "listening on a daily basis" music library come in at about 3.5GB. That's music i like to hear every day. That's plenty to fit on a Jukebox, and obviously on a Touch as well</LI>
    I'm out on a research farm for about 5-7 hours a day. Both the 6hr Jukebox and the 24hr Touch battery deli'ver.</LI>
    The Jukebox has fully functional EAX settings, the Touch doesn't</LI>
    With a set of surround headphones, i can have 4 channel surround on the Jukebox. Stereo only on the touch.</LI>
    The Jukebox has a three band EQ with programmable crossover frequency. The touch has built in EQ and a faulty programable one.</LI>
    The Jukebox has a tree structured queue list, and individual items can be removed or added. Nothing like that on the touch</LI>
    Pushing UP/DOWN simultaneously allows quick scrolling, and there's a page up/page down function on the Jukebox - the lists also wrap so you can go from top to bottom easily. Scroll, wait, wait, and wait on the Touch. If you're at the bottom of a big playlist... well, forget it.</LI>
    Play mode available directly from Current Track screen.</LI>
    All i need is a microphone to record lectures on the Jukebox. The touch requires an external part to do that.</LI>
    I choose what comes up when the jukebox starts, and what volume. That way i don't scream bloody murder going from my car to my headphones.</LI>
    Tracks, artists, and albums starting with 'the' have 'the' ignored on the Jukebox. The Clarks is filed between Chumbawumba and Coldplay on the JB.</LI>
    Sleep and wakeup timers on the Jukebox.</LI>
    Hardware settings on the Jukebox let me choose between it running like a Beetle Diesel, getting 56 mpg, or a Ferrari Testerozza, and getting single digit mileage.</LI>
    No "push me to play everything and screw up your playlist" button on the Jukebox.</LI>
    What advantages does the Touch have over my Jukebox?
    Higher SNR (98 vs 96 i think, cant find Jukebox spec)</LI>
    Smaller</LI>
    Better battery life</LI>
    Promise of better firmware</LI>
    I'm an audiophile-geeky-gadget guy. I own 99.98% the MP3's i have on my PC. NapsterToGo, Y!MU, amongst others are appealing to me, as i refuse to 'stick it to the man' by illegally pirating music. You say only the record industry is getting screwed over - don't forget the musicians have a paycheck too. Hoping for support, just like we got support when DRM first came to be for our JB's, our Zen's and such, i loyally bought your Touch. I even remember the combo beta/stable firmwares.
    When a product that you made over fi've years ago has more features, functions, and capabilites than something you've released recently - that's quite a tradgedy.
    I remember a bus ride sophmore year in HS, my first MP3 player. The night before i spent hours ripping the songs to the player until 5am. It was cool, people were amazed, i sold them on this "thing" that held every song that they owned. It was both 337 and Chic.
    Now people see the Touch and ask, "is that the new iPod?"
    I found that sales is like a marriage. You need a first impression, you need your customer to fall in love with the product, and you need to keep them interested as long as possible. Well, after fi've years... i want a divorce. I won't buy an iPod - Apple will lose share because of their control-freak nature on their products. But i won't be buying Creative products anytime soon, or even again.
    This message was a bit of humor to begin with - i started fiddling with my JB this evening. Then it got me to thinking, what happened to the creative that used to post new drivers/firmwares/updates every week or so? Where'd they go?
    Where's that old Creative Labs that was just that... Creative?
    EDIT: I thought you might like to know that the FW on the JB is 4.0/2.98beta... the last dual boot beta creative put out. Still available on the Nomadness.net site
    Message Edited by harikari on 07-26-2005 08:3 PM

    harikari wrote:
    When i first got my JB, it had battery life comprable to an iPod, about 2 hours. With the ability in later firmwares to tweak HD settings, i could extend it to about 6 with minor inconviences like load time and some gapping.
    It depends on the files though. With 28kbit/s MP3s you would get about 4 hours, maybe more with higher capacity batteries.
    At the time, the only other portable audio was CD, and think of how many people still have and use CD players. True it was a projectile weapon...
    Actually I liked that its form factor was similar to a CD player. It meant getting cases was easy, although I went for the skin case.
    And i liked the NiMH batteries, they could be used in anything, and they lasted much, much longer than alkaline. You know why the JB says "Use only Creative NiMH?" One, so you didn't recharge alkaline cells; two, alkaline cells ran the player for <EM>maybe</EM> and hour and a half, to
    ps.
    They were certainly worried about using the wrong batteries in it, although of course any NiMH batteries, ideally high capacity, work.
    Oh, and i booted the JB and Touch (cold boot)... took about the same amount of time. Touch was a 'touch' faster.
    Not if you add content to the NJB though. Every time you change content it has to rebuild the library.

Maybe you are looking for

  • Error while Migrating the custom routines in Transformations

    Dear All, I am in the process of migrating BW 3.5 to BI 7.0.I migrated the Standard cubes and DSO's from BW3.5 to BI 7.0 flow successfully. But while migrating the transformations which are having the custom routines,I am facing the below errors. The

  • Performance query on 0IC_C03 inventory cube

    Hello, I am currently facing performance problems on this cube. The query is on material groups so the number of row returned are not to high. The cube is compressed. Could aggregates be a solution, or does this not work well on this cube because on

  • A way to re-enable scroll bar buttons in Gnome (GTK) 3?

    Is there a way to re-enable or add the scrollbar buttons (on the top and bottom of vertical scrollbars or on the left and right of horizontal scrollbars) in Gnome (GTK) 3?

  • Hits keep coming

    After all the BS with the mouse and keyboard, I now verify the disk in Disk Utility and get, The Volume Macintosh HD was found corrupt and needs to be repaired. It tells me to use disk utility, but the repair button is grayed out. Does this mean I ha

  • Assessable Value in Import Purchase Scenarion.

    Dear Experts, Can anybody please explain, what is the Assessable value in Import Purchase.         1) Whether it is Material Basic Price.         2) Value after discount calculation on basic price.         3) Value includes interest amount         4)