Non-booting Mac mini (stuck at gray screen with no Apple logo or others)

We've got a G4 Mac mini whose motherboard was recently replaced. I've put it back together carefully following the instructions on pbfixit.com, but I can't get it to boot.
When powered on, the chime sounds normal, and the screen comes on after a few seconds with a gray background--no Apple log, no spinner, no error, no flashing icons, nothing.
I've already zapped the PRAM 3 times using OptCmd+PR, no go.
I'm able to get into OpenFirmware using OptCmd+OF and have done reset-nvram and reset-all, restarting the machine, but no luck. The system date remains current also, indicating perhaps it's not resetting the PRAM either way somehow.
The disc drive won't accept a boot CD or DVD as if it's unpowered, but it's snugly connected.
I'm unsure what to test next. Suggestions? Thanks.

Greetings,
I just had the exact same problem with a Mini. Would only boot to a gray screen no matter what I did. Booting into the OpenFirmware did help, booting into the Startup utility (by holding "T" down at startup showed no hard drive and no CD/DVD drive.
Hold on to your hat . . . .
The issue was the battery. These guys have a Lithium battery that allows them to boot up, a battery that can be purchased anywhere that sells those kinds of thing. I bought 2 for $3.50, it was more time and trouble to get into the case and get at the logic board but once the battery was replaced everything works like a dream.
Here is an excellent step-by-step tutorial about getting into the case http://www.sterpin.net/uk/ddMacMiniuk.htm. Just make sure that doing so doesn't void any warranties.
Good Luck!
Gail

Similar Messages

Mac mini stuck on gray screen with spinning icon

I can't startup from either the hard disk or even a CD (pressing down the C key while restarting) now on my Mac mini. I tried reseting the PRAM, the PMU and multiple other restarts. I also did the command-V restart and get the following as the last lines of text:
Feb 26 19:12:55 launchd: /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow port /dev/console exited abnormally: Trace/BPT trap
Feb 26 19:12:55 launchd: getty repeating too quickly on port /dev/console, sleeping
After a few moments, it continues to loop through these same messages again but with updated times by about 30 seconds.
My Mac is dead and it's afterhours and I can't get tech support. I'm typing this from my Sony Vaio... Can someone help?
Thanks

too old to remember how resolved, replace the Mac mini with something else

I am not able to use my Mac while FileVault is encrypting. Is it frozen on a gray screen with the apple logo. Is it actually encrypting?

I have an early 2008 MacBook and running iOS Lion. I just turned on FileVault and restarted my computer as instructed. It told me before hand that I would still be able to use my Mac while the files were being encrypted. However, when I logged in on the secure gray login screen, I was only directed to a plain gray screen with the apple logo in the center. There are no time turners or anything moving. Is my Mac encrypting or is it frozen in some sort of way? If it is encrypting, how long does it usually take? and if it is frozen, how do I unfreeze it?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My Macbook pro 13 inch is stuck on a gray screen with the apple logo, how do I fix this?

Sooo, I was using my laptop for a while and the charger was kind of broken, it was dip in and out, and slowly I got a "Service Battery" notification. I updated my system and now everytime I try to boot up my computer it'd show a gray screen with the apple logo and a loading bar with a circular loading icon but it never actually boots up. It stays stuck at that loading screen. I don't think it's because I uploaded my system that it happened, but I'm wondering if it's because I didn't change my charger/battery, and I'm wondering if I have to get the harddrive changed or is there a way for me to recover my files and whatnot without having to whip it. Please help, and thanks in advice to any help offered.

Dwaniej,
you can try this: boot your MacBook Pro into Recovery mode by holding down a Command key and the R key as it starts up. Once the OS X Utilities menu appears, select Disk Utility. On the left-hand side of the Disk Utility window, select your internal disk’s boot partition (typically called “Macintosh HD”). On the right-hand side, press the Verify Disk button if it’s not greyed out; if it is greyed out, or if it reports that errors were found, press the Repair Disk button. Once the verification/repair is completed, exit Disk Utility and select Restart from the Apple menu to restart in normal mode. Does it get past the grey screen now?

HT3964 I am not able to reboot my Mac desktop. When I switch on the Mac, I get a white screen with the Apple logo and the little wheel below that goes round and round but the computer refuses to boot.

Hi, I am not able to reboot my Mac desktop.
When I switch on the Mac, I get a white screen with the Apple logo and the little rotating circle.
The system refuses to boot.
What can I do?
Marcus

We need to get you moved. This forum is for mini-tower Macs built between 1998 and 2005 and doesn;t get as much traffic ("eyeballs on the problem") as the forums for newer Macs.
Please do "About this Mac" from you Apple menu and tell us what that says for "processor" and Mac OS version. Looks like this:
or this for later Mac OS versions:
With that we can figure out which of the two iMac forums you need and get the Hosts to move your post.

My MacBook Air can't get past the gray screen with the apple logo. What's the fix?

My MacBook Air can't get past the gray screen with the Apple logo, so I can't login. Does anyone know the fix for this?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
How to use and troubleshoot FireWire target disk mode
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Before reconnecting an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, reboot as usual (i.e., not in safe mode.) If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see above for instructions.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it produces. Look for the line "Permissions repaired successfully" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

My MacBook Pro stated that it needed to be updated. I clicked yes to restart the computer and update but when it restarted it stays on the gray screen with the apple logo and then pops up, stating "unable to find driver for this platform." What do I do?

My MacBook Pro stated that it needed to be updated. I clicked yes to restart the computer and update but when it restarted it stays on the gray screen with the apple logo and then pops up, stating "unable to find driver for this platform." What do I do?

Boot into Recovery by holding down the key combination command-R at the startup chime. Release the keys when you see a gray screen with a spinning dial.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with networks that require any kind of authentication other than a WPA or WPA2 Personal password.
When the Mac OS X Utilities screen appears, follow the prompts to reinstall the Mac OS. You don't need to erase the boot volume, and you won't need your backup unless something goes wrong. If your Mac didn’t ship with Lion, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.
Don't install the Thunderbolt update -- it's defective.

My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg():Socket is not connected

My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg(): Socket is not connected

If running 10.7 or later hold down Command-R at Startup.
This should invoke recovery Mode.
Choose Disk Utility.
Select your Hard drive. Inspect the SMART Status in the lower right of the window for "Verified".
Select the Mac OS X Volume (originally Macintosh HD) click (Repair Disk)
If errors, run again until it comes clean or gets stuck.
Report any error messages.

I get a gray screen with the apple logo at start up and the trackpad doesn't work

My MacBook Pro has run fine until yesterday. It froze and wouldn't receive commands from the trackpad. I was still able to move the cursor but clicking or tapping the screen did nothing. I tried restarting but got the gray screen with the Apple logo and the spinning wheel. To get pass this I have tried resetting the NVRAM/PRAM and performing the safe boot. I also tried using the Disk Utility at start up but since I can't use the trackpad it was unsuccesful. I got pass the gray screen once performing the safe boot and restarted and everything run fine (including the trackpad) for about 20 minutes before freezing again. Now I'm back at the gray screen again and can't seem to get pass it again.
Any advice what should I do next?

I would back up the files and start looking at the HDD. Open DISK UTILITY>FIRSTAID.
Ciao.

Why is my laptop freezing on the gray screen with the apple logo when trying to power on?

In the last hour, one time it came on as far as the user sign in. But I wasnt able to click on a user, because the curser was constantly spinning. I have tried taking the battery out for a minute and putting it back in. Nothing. I have tried starting it while holding down the option key, and it pulled up a screen with a picture of my hard drive on it. So I clicked it, and it just goes to the gray screen with the apple logo, and does nothing else? Can anyone please help me? Are there any other keys that I can hold while turning it on?
Thanks

See Here for:
Frozen or unresponsive iPod touch
Reset your phone:
Press the sleep/wake button & home button at the same time, keep pressing until you see the Apple logo, then release the buttons...
The Basic Troubleshooting Steps are:
Restart.. Reset.. Restore from Backup... Restore as New...
Restarting your device
1) Press and hold the Sleep/Wake button for a few seconds until the red "slide to power off" slider appears, and then slide the slider.
2) Press and hold the Sleep/Wake button until the Apple logo appears.
Follow these steps to reset your device
Note: Reset your device only if it is no longer responding and the steps above do not work.
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
iPhone Reset
http://support.apple.com/kb/ht1430
Backing up, Updating and Restoring
http://support.apple.com/kb/HT1414

My iPhone 3gs is stuck on black screen with the apple logo, help

my iPhone 3gs is stuck on black screen with the apple logo, help

then get it replaced if that doesnt work or try to le tthe battery die and recharge

TS2570 my imac 27 inch 2011 is not booting up, the i mac is stuck on a gray screen with no apple logo or anything

my 27 inch 2011 iMac is not boting up, the cumputer is stuck on a grey screen with no apple logo or spinnign wheel. The iMac is not giving power to the keyboard as it is not ligthing up the caps lock botton when pressed.

Contact Apple Service, iMac Service or Apple's Express Lane. Do note that if you have AppleCare's protection plan and you're within 50 miles (80 KM) of an Apple repair station, you're eligible for onsite repair since yours is a desktop machine.

Stuck at white screen with grey apple logo

When I turn on my MacBook Pro, it is stuck at the white screen with grey apple logo. What do I do?
Thank you!

I was looking at this and it helped! http://support.apple.com/kb/TS2570
1) Disconnect, test peripheral devices and network cables - didn't work
2) Perform a Safe Boot - didn't work
3) Reset the NVRAM / PRAM - worked, yay!

My macbook pro will not get past the gray screen with the apple logo and a loading bar.

My macbook pro will not get past the grey screen with the apple logo after attempting to load for hours. I have already tried resetting the NVRAM/PRAM and a couple other tricks and no luck. Anyone out there have suggestions for my problem? Help would be much appreciated since i use my computer for everything at school and i am in desperate need to get this baby working again.

You didn't say which OS in your tag, but maybe you might find something here.
http://support.apple.com/kb/TS2570
http://support.apple.com/kb/PH4191
http://support.apple.com/kb/PH7213
http://support.apple.com/kb/HT4125
http://support.apple.com/kb/HT2213

Mac mini stuck at gray screen HELP!!!!!!!!!

Hi,
i have my mac mini stuck at a gray screen can you help me

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 3
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 4
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 5
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 6
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 7
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 8
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 9
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 10
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 11
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Non-booting Mac mini (stuck at gray screen with no Apple logo or others)

Similar Messages

Maybe you are looking for