Non Graphic card in 760GM-E51 PCIe x16 Slot

Why can't I use the on board graphics and attach a PCIe x2 or x4 SATA controller in the PCIe x16 slot? Any non graphic board is simply ignored.

Quote from: Bollwerk on 24-December-10, 03:39:17
That did it! Apparently, the bridge chip changes it between x16/x1 and x8/x8. Once I switched it to x8/x8 (SLI mode), the Asus card was recognized.
Thanks!
Almost, it changes the slots from x16/x0 to x8/x8
Nice to hear you got it sorted out
Merry Christmas and best wishes

Similar Messages

MSI K9AGM2-FIH: PCIe x1 card in PCIe x16 slot

Am trying to get a PCIe x1 2-Port Sil3132 SATA Controller to work in a x16 slot
system boots without any problems, the card is found, and it shows up when booting
but here is the problem, windows wont boot, when i remove the card from the x16 slot it boots fine
windows is run via the onboard sb600
x1, x4, x8 cards should work in a x16 slot just fine, after with i have heard

Question, why do you want to use that card?
Also, it might be possible that drive-letters change in Windows, so it can't boot anymore.
Try booting with the Windows Boot-cdrom, load the Sil driver and see what letters you get.
You might need to change the boot.ini

TS140 LSI 9300-4i4e not seen in PCIe x16 (slot #1) however works in x4 (slot #3)

I have some TS140s (70A4001LUX 5U with i3-1225 v3 processor) that have tried installing a couple of different LSI 9300-4i43 12Gbps adapters that are not recognized when inserted into the PCIe x16 (e.g. slot #1).
However those cards are recognoized when inserted into the x4 slow (e.g. slot #3). Have tried various LSI 9300-4i4e (cards have most recent fw and bios) in a couple of different TS140s and see the same results. Have verified other cards working ok in the x16 slot.
In the process of updating TS140 BIOS to most recent late fall 2014 version to see if that magicly clears things up.
Has anybody else seen this and know of a resolution other than dont use the LSI 9300 in slot #1?

@I_am_Nivek thks for the info and ideas, I should have mentioned that the onboard RAID on the TS140 was not being used, in the BIOS/Setup, the ATA mode is set to AHCI (other options are IDE or RAID). Also as an FYI/FWIW, on the TS140 or at least the version that I have, the RAID/IDE/ATA is accessed via the "Devices" tab and then under the ATA section. I do recall seeing the "SCU" mode on a different Lenovo system that I have used, might have been a TD340 iirc.
However with the RAID disabled (as it had been), the adapter card still does not appear.
Regarding the boot mode, good idea, I had the TS140 in CSM which enabled both UEFI and BIOS, tried changing it to disable CSM which only allows UEFI mode. However that did not work either.
Is there a different BIOS as well as different motherboard firmware version available vs. what I am using (see above)?

Z97 gaming 5 motherboard-2nd PCI x16 slot wired at x8?

Hi,
I connected my gtx980 on my 2nd PCI x16 slot and GPU-Z reads as x8.However,when I connected it back to the 1st slot,it reads as x16.Would like to confirm if that's the supposed outcome or is there any BIOS configuration that I can change?
Thanks

Yes the second x16 sized slot is only wired for x8 operation. the only way a board like that could have 2 full x16 slots is if it has PLX chips but they are very costly and only get used on stuff like a X-Power model board!
so its behaving normally on yours as that is how its setup!

A55M-P33 and support for non-graphics cards in PCI-e x16 slot.

Does this motherboard support using an LSI raid card in the x16 slot, or does it only support graphics cards? I am building an Unraid box and would like to use the slot for an x4 or x8 raid adapter in IT mode.
Thanks Matt

Well wait around and see if anyone else post's but if you do a quick search of pcie raid controller you will find varying results. All the results I found were with Intel boards though so all I can say is no guarantees.
This is Msi's official response for raid cards:
Quote
PCI-Ex4 RAID cards are designed and tested to work with Server/Workstation mainboards. Therefore MSI does not test server/workstation products with our desktop mainboards.
Please contact the PCI-Ex4 RAID card supplier for compatibility.
You can try to contact msi, but I assume they will tell you this.
>>How to contact MSI.<<
I have also heard some no so hot things about LSI service, I can however vouch for Adaptec's service, so you might want to contact both and see if they have tested and combinations.

H77MA-G43, which pci x16 slot to use?

i recently bought the h77ma-g43 mainboard which has both the pci x16 v2.0 and 3.0 slots, i was wondering which one to use for my nvidia gtx 580 which is a v2.0 card. please reply soon...thanx

Normally, it is the PCI-E 16X33 slot closest to the CPU.

Hp p400 pci-x8 running in pci-x16 slot

My thanks in advance for any help I may receive.
I am currently experiencing a "device not found error" whilst trying to use an HP p400 array sas pci-x8 adapter in a pci-16 slot.
The motherboard is a Gigabyte H81M-S2PV,
8 gigabytes of RAM,
650 Watt power supply and
award modular bios 6.00g and
intel i3 chip
HP P400 with 512 cache and battery
I only have access to the slots mentioned. I have tested the adapter in three other machines which have the same exapnsion slot arrangements.
Please clarify if the pci-x8 card should function in the pc-x16 slot? I am trying to assertain if my adapter is faulty.
Many thanks
Mutasim
This question was solved.
View Solution.

Thanks for your input PlumCrumble.
I was silently sure the card should work but felt it would not hurt to get another opinion. This reply is accepted as a solution for the first question.
If I may be bold can I ask if you have any suggestions on my current scenario: When starting the PC, the screen is black for almost six minutes no messages or indications as to what is happening - then after the period of six minutes or more the PC continues to the normal boot functions; post, loads Windows etc. The HP ORCA and other utilities reports device not present. However the Widnows device manager indicates a device with driver error.
In my humble thinking I believe a device is detected but the firmware or required software is missing, After trying the Proliant repair and installation boot disk, I am little lost as to what software is required to intialise the the device and set the correct IRQ at the BIOS level of the process.
Is there software and firmware utility available for the HP P400 at the DOS level that I need to be aware of - I am a novice with this particular HP device and any help would be greatly appreciated. Linux system also reports the same results.

Is it possible to add an extra Graphics card: ATI X300 SE PCI express

I have a PowerMac G5 with ATI Radeon 9600 XT(AGP) installed. Recently my friend gave me a ATI X300 SE PCI express card and I am wondering whether I can add this card in the G5 and hook up another monitor to it.
The ATI and Apple websites didn't mention this card is supported, so should I just give up this idea? Thanks.

Another reason you can't use the ATI X300 -- it has Windows PC ROM code. You can only use cards in the Power Mac with OS X compatible firmware.
As of this date, the fastest AGP card you can buy to replace your old one is the Mac Edition of the Radeon X800 XT. It runs $399 from various sources (ATI online store, Apple online store, MacSales.com, SmallDog.com, and Buy.com).

P35 PCIe X16 slot

I read that the 2 PCI e video slots will sense which one has a card, and set that one to X16. Is this the case? The reason I ask is my GeForce 9600 (only 1 slot wide) will not seat in the white slot due to interference from the Southbrdge pipe. I had to move it to the yellow slot.
Thanks,
Dave

Thanks...removing the cover gave me just enough space to get the card working although I doubt it's seated all the way. I may have to bend back a few of the cooler fins to make a proper fit.
Thanks again,
Dave

Looking for a better graphic card. Need feedback and suggestion

I'm looking to get a different graphic card but I'm not sure really what to buy,
These are my computer specs
Computer: Gateway Gt5228 Media center edition
OS: Windows Xp
Current graphic card: NVIDIA GeForce 6100 PCI Express Slot avaliable
I was wondering what would be a good graphic card that is a good significant upgrade. I'm looking for one that has a significant increase over what I have right now, it doesn't necessarily have to be the best out there.
I want to be able to play a game call Diablo 3
These are the High and low Performance, that the game will run with.
Supported - High PerformanceNVIDIA AMD/ATI INTEL
GeForce GTX 590
Radeon HD 6990
N/A
GeForce GTX 580
Radeon HD 6970
GeForce GTX 570
Radeon HD 6950
GeForce GTX 560 ti
Radeon HD 6870
GeForce GTX 550 ti
Radeon HD 6850
GeForce GTX 480
Radeon HD 6790
GeForce GTX 470
Radeon HD 6770
GeForce GTX 465
Radeon HD 6750
GeForce GTX 460
Radeon HD 5970
GeForce GTS 360M
Radeon HD 5870
GeForce GTX 295
Radeon HD 5850
GeForce GTX 285
Radeon HD 5830
Geforce GTX 280
Radeon HD 5770
Geforce GTX 280M
Radeon HD 5750
GeForce GTX 275
Radeon HD 4870
GeForce GTX 260
Radeon HD 4870
Quadro FX 5800
Radeon HD 4850
Radeon HD 4800
FirePro 3D V8750
FirePro 3D V8700
FireStream 9370
Firestream 9350
FireStream 9270
FireStream 9250
Supported - Low PerformanceNVIDIA AMD/ATI INTEL
GeForce 9500 GT
Radeon HD 3650 AGP
HD Graphics 4000
GeForce 9400 GT
Radeon HD 3650
HD Graphics 3000
GeForce 9300 GS
Radeon HD 3600
HD Graphics 2000/1000
GeForce 8800 GS
Radeon HD 3470
GeForce 8600 GT
Radeon HD 3450
GeForce 8600 GTS
Radeon HD 3430
GeForce 8500 GT
Radeon HD 3200
GeForce 8400 GS
Radeon HD 3100
GeForce 8400
Radeon HD 2600 XT AGP
GeForce 8300 GS
Radeon HD 2600 XT
GeForce 8300
Radeon HD 2400 Series
GeForce 8200
Radeon HD 2350
GeForce 8100
Radeon HD 2100
GeForce 7950
Mobility Radeon HD 4530
GeForce 7900
Mobility Radeon HD 4330
GeForce 7900 GS
Mobility Radeon HD 2600 XT
GeForce 9500M GS
Mobility Radeon HD 2600
GeForce 9500M G
Mobility Radeon HD 2600
GeForce 9400M
Mobility Radeon HD 2400 XT
GeForce 8600M GT
Mobility Radeon HD 2400
GeForce Go 7900
Mobility Radeon HD 2300
GeForce Go 7800
Mobility Radeon X2300
Quadro FX 5500
Radeon X1950 Series
Quadro FX 4500
Radeon E2400
Quadro FX 4000
FirePro 3D V7750
Quadro FX 3500
FirePro 3D V5700
Quadro FX 3450
Any help would be greatly appreciated
Which ones can i use with my computer but without the need to buy nothing else.
thank you
-Geo

Honestly I wouldn't spend too much trying to upgrade your computer. It has an aging dual core Athlon processor, and only 2GB of RAM. Even with the highest top of the line card, with that CPU/RAM setup, your computer is probably going to struggle to run it.
Hate to be the bearer of bad news.
If you like my post, or solution to your issue/question, go ahead and click on the little star by my name and/or accept the post as the Solution. It makes me happy.
I'm NOT an employee of Best Buy, or Geek Squad, though I did work as an Agent for a year 5 years ago. None of my posts are to be taken as the official stance that Best Buy will take on your situation. My advice is just that, advice.
Unfortunately, that's the bad luck of any electronic, there's going to be bad Apples... wait that's a horrible pun.

Graphics card wont fit??

I have an HP Media center PC m7334n with ATI radeon xpress 200
The graphics card I tried to install was MSI ATI Radeon HD 4350 512mb
But it seems to not fit because of the gold things that block it on the card..
Could i perhaps take something apart to make it fit?

You have to install the MSI Radeon HD4350 video card in the black PCIe x16 slot.
It will not fit in the white PCI slots.
You will need to move the plastic tab towards the memory slots as you install the card. That will allow the card to completely enter the slot. Otherwise it just will not go in.
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

[MSI P35 Platinum] Graphics Card Slot

Hello,
I just bought the MSI 560 GTX graphics card. My motherboard is MSI P35 Platinum so i was wondering if i can place the graphics card in the 2nd PCI-E slot or this could occure problems. This is my motherboard:
so my question is: can i put the graphics card in the YELLOW slot? Cause it won't fit in the upper PCI... Thanks

Quote from: Jack on 03-September-11, 19:12:09
Why doesn't it fit? It should fit without problems.
Because of the I/O controller (i think this is it...)
Quote from: Jack on 03-September-11, 19:12:09
You can do that, however, in that slot, the video card will only get x4 lanes assigned to it (instead of x16 lanes in the primary PCI-Express slot).
And what difference does this make?

NVIDIA - GeForce GTX 660 Ti 2GB GDDR5 PCI Express 3.0 Graphics Card

How difficlut is it to replace a grphic card in a HP P6210Y

Here are the specs for your HP Pavilion p6210y Desktop Computer. According to the specs, this model has a PCIe x16 graphics card slot and a 300 watt power supply. In theory, the computer's PCIe x16 slot is v2.0 and a PCIe x16 v3.0 graphics card should work in this slot. You will need an open space next to the PCIe x16 slot to accomodate the GTX 660 Ti. Please see "Adding or Replacing an Expansion Card (Video Card, Sound Card, etc...)" for instructions on installing a graphics card in your computer.
You will also need to replace the power supply with a unit rated to work with your new graphics card. It appears the minimum system power supply requirement for the GTX 660 Ti series of cards is 600 watts. Please consider the Corsair CX600 or CX600M for your power supply needs. The Corsair CX600M is modular, which allows for better cable management and air flow in the HP case. Please see "Replacing the Power Supply" for instructions on installing a new power supply in your computer.
Please click the white KUDOS star to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

SG3730Il Graphics card Support using PCI EXPRESS ...

Hello Everyone ! !!!
My Question To You people is About Hardware Configuration On Hp-SG3730IL ....
First Of All ... I need To Show you Graphics Card Support .. USing Product Specifications. ...
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01690252&tmp_track_link=ot_faqs/top_issues/en_u...
It says .... My DEsktop can be Upgraded Into ""Also supports PCI Express x16 graphics cards""
So Mine is PCI Express 1.0 or 2.0 ?.. How can I find It ?...
So .... Can Supporters can Suggest Me .. To use Best Graphics card ??..
I need MINIMUM of 1GB memory graphics ! !
Please . Support My Hardware Support Practically !! .. I mean .. It should work Practically too !
Thanks in Advance !

Hi,
The NVIDIA should work with the PCI-E 1.1 bus that your PC has in it. You might want to search this forum for NVIDIA 650 compatibility issues.
Know what the return policy is before you buy.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

MSI Eclipse Plus, SLI, PCI and double hieght graphic cards.

I'm intrested in building a system with the Eclipse Plus and 2 card sli setup.
The manual states that for a 2 way sli, graphic cards should be placed in slots top 2 pci slots. MY graphic cards are double height so placing them in these slots would block out the only pci slot available which I need
Is it possible to mount the graphic cards in the first and 3rd slot and still achieve sli?

Are you sure about that PD?
syrus will just have to give it a try. Please let us know if it works.

Non Graphic card in 760GM-E51 PCIe x16 Slot

Similar Messages

Maybe you are looking for