Non working keys

i have n 8800 and keys to the right of rows (and including T, G and V) T, G and V do not work. All keys to the left do work. is there something i can do to restore there use? It seems that when my sim card is inserted into the 8800 the right side keys don't work. when i remove the card, all the keys work.

you did not push the clips all the way in to secure the ribbon cable for the keyboard. the clips push a little further than you think if you do it right you can tug on the cable and can't pull it out.

Similar Messages

HELP some non working keys on keyboard HP G60-519WM laptop..might need help removing keys?

I have had this laptop for a couple years now and I haven't had any problems with the keyboard, keys or their connection with my laptop. I have never spilt anything on it or been aggressive with the keyboard either. Tha essential problem is that now my T,Y,P,K,M keys and the CTRL and PAGE keys (to the right of space bar) no longer work after cleaning my computer. There might be more but I haven't been able to tell what the Fn button and some function buttons fully do.
How it all began:
Two weeks ago I noticed that the fan on my computer kept running and the computer would get warmer quite easily and take longer to cool down. It also started lagging or loading things slower than it should.
So I went onto HP's site and found their information on cleaning fans and vents and the information I saw in it mentioned all the problems my computer had. So I decided to follow their directions on how to clean the fan, vents and keyboard. I noticed alot of dust and small hairs from my dogs and small lint balls..more debri then I thought would be in my laptop.Nothing huge or that I would see as damaging but it definitley needed a cleaning.
So I let the computer sit for a while and then I turned it on and that is when I noticed some of the keys no longer worked. I decided to see if the device was installed properly and the computer said it was working fine, so I figured it might be debri stuck under the keys.
I followed the directions on how to turn off the computer and I got a small tool and a light to look under the keys and remove what I could see.. I did that with all of the keys, not just the ones that stopped working. I was surprised I was able to get alot of stuff out from under the keys. BUT the same keys still didnt work.
So far at this point I have used the on screen keyboard and an external keyboad (what I am using to write this) and thos keys work fine. I have checked the BIOS and the same keys didn't work (on the bios black screen). I tried to check the device and for updates or any errors and I didn't see any problems. I attampted to uninstall my keyboard which initially said it was a 101/102 keyboard and then when i restarted to finalize the process..the device registered in its place was now called a standard keyboard and the computer didnt ask me to reinstall the one i uninstalled.initially. So I don't know if that was a successful way of doing that or not.
Sorry for my novel but I just want to make sure anyone who can help knows what I have been doing. My questions now are;
A. did I do the bios test right?
B. did i uninstall my keyboard right? if so then why would a different keyboard already be on as a device without me doing anything? if i didn't please help me on how to..
C. I feel like there is debri trapped under these kes, is there anyway to remove each key to clean and inspect? if so how, because I haven't been able to find out any useful information about that process on this computer/keyboard?
D. is there any thing else I could do besides removing the keyboard and replacing it?
PLEASSE HELP ME?? THANK YOU!

you did not push the clips all the way in to secure the ribbon cable for the keyboard. the clips push a little further than you think if you do it right you can tug on the cable and can't pull it out.

Funky non or non working control key

I'm on my second Apple Wireless Keyboard. This is the older one with the numbers on it A1016. The first one needed to be retired because issues and some from the function of the control key.
On my second used one its like new and I cleaned it well but the control key is the only non functioning key. I even took it apart and cleaned the clear sheets with the sensors but that didn't help. Is this a known issue? Or is there a fix beyond getting a new keyboard?

There is no known issue that I am aware of.....
Barry

Trouble with Non Cumulative Key Figures

Hi all of you,
I am working on Non Cumlative Key Figures, (NCKF). I have the data like this
Sales rep S100 visited SHOP S1 on 1st Jan and 10th Aug, and transacted worth 100 and 500
SHOP S2 on 1st Mar and 1st July and transacted worth 200 and 300
SHOP S3 on 3rd Sept. and transacted worth 400
Sales rep S200 visited SHOP S1 on 1st Jan and 1st Aug and transacted worth 100 and 300,
visited SHOP S2 on 1st April and transacted worth 200
I created Non Cumulative Key Figure in the following manners:
In modeling in InfoObjects I double clicked on my key figure BILLAMT and selected the Aggregation tab. I selected Counter (all values) for Exception aggregat. By default Agg. Referen. Char was 0calday. I then activated the info object and went to BEx. Here I took other IOs like Salesrep, Shop NUM and Dt. Of trans in rows and Bill amt in columns and executed the report. I am not getting the output how it should come for NON cumulative key figures.
But when I right click the key figure Bill Amount in BEx in change query mode and select properties. I go to the option Calculate result as and selected the option as Count all values. And in another option Calculate Single Value as I selected the option Count all values. I said OK, saved the query and executed it. Now the output is similar to how it comes for a Non Cumulative Key Figure query but I am unable to understand the output.
Now my doubt is where do we set the properties for Non Cumulative Key Figures? Is it in the Administrator Workbench under Modelling under InfoObjects?
OR
Is it in BEx change query mode by right clicking on the key figure and selecting properties?
Please explain.
Thank you
TR.

As for the setting for Non Cumulative key figures...the default setting is done in the Key Figure properties, where u can define the Exception Aggregation. This property is used as such in the query, but if suppose u are getting the normal aggregation in the query , what you could do is "Create The Key Figure as Global Calculated Key Figure in Bex" and go to properties...click on the Button for aggregation ..select the aggregation and define with respt to 0CALDAY ..here.
Hope this helps.

Planning on Non-Cumulative Key Figure

Hello,
is it possible to plan data on a non-cumulative Key Figure?
SAP_ABA     701     0005     SAPKA70105     Cross-Application Component
SAP_BASIS     701     0005     SAPKB70105     SAP Basis Component
PI_BASIS     701     0005     SAPK-70105INPIBASIS     Basis Plug-In
ST-PI     2008_1_700     0001     SAPKITLRD1     SAP Solution Tools Plug-In
SAP_BW     701     0005     SAPKW70105     SAP Business Warehouse
BI_CONT     704     0003     SAPK-70403INBICONT     Business Intelligence Content
ST-A/PI     01L_BCO700     0000          -     Servicetools for other App./Netweaver 04
We implemented also the How-to Paper Copy and Paste in the Web Template but it isn't working in a proper way. UnderPrerequistes in the How-to Paper I found IE 7.0 and Clipboard. But I was informed that we have an higher Level.
Thank you in advance for your help.
Kind Regards
Doris

Not possible.Please find the help link for more details.
http://help.sap.com/saphelp_nw70/helpdata/EN/43/1c3c7031b70701e10000000a422035/content.htm
Regards, Hyma

Non cumulative key figure and fiscal period 13

Hi,
We have defined a non cumulative key figure. In the cube, the non
cumulative characteristic is the fiscal period (0FISCPER).
This non cumulative key figure works fine from period 1 to 12, but
displays nothing for period 13 (and 14, 15, 16).
We want to display the balance for the special periods 13 to 16, Is
there a way to do it?
Thanks,
Gabriel

Hi,
Yes I am sure, there are some amounts posted in period 13. And even if there are no amount posted, there was a balance in period 12, so the balance should stay the same in month 13.
The balance in month 1 of the next year is correct: balance of period 12 + amount posted in periods 12, 13...
Gabriel

Integrated Planning and Non-cumulative key figure

Hi
I´m creating an Integrated Planning application and a problem has occurred. The users want to plan on inflow and outflow and at the same time have a row with the total sum in the same layout (they are planning on 0CALMONTH and 0ORGUNIT) This can e.g. be solved through use Web Application Designer with one planning query and one traditional query.
Any way. I have created a non-cumulative key figure with an inflow- and an outflow key figure. The problem is that the non-cumulative key figure starts working first when I change the planning mode from plan status to load status. I could use function modules, to change the status, behind the save button but there are several users who are planning at the same cube at the same time and I don´t want to lock the others from planning.
How to solve this?
- Is it possible to restrict the switching, from plan to load, by setting some kind of filter at the users org.unit? (0ORGUNIT is an authorization object)
- Is it possible to create a process chain and then load the data to another cube for reporting at just this key figure? And also here have a filter at the org.unit
I will gladly get all kind of idea and input to solve this problem. Maybe there is some other way to go than using non-cumulative key figureu2026

Thanks for your answers
I have tried different scenarios and I will use a u201Dsave-buttonu201D. In the save-button I use the commands SAVE_DATA and EXECUTE_PROCESS_CHAIN. The command u201CEXECUTE_PROCESS_CHAIN starts a process chain that switches from plan mode to load mode and then back to plan mode again.
One new problem has arisen. The non-cumulative key figure is updating if an existing value (inflow- or outflow) is changed. But if an input is made to an empty cell, without value, nothing happen when I press on the start-button. BUT if I refresh the browser the non-cumulative value is updated!!!
Is there any command in WAD that refresh the whole page? If so I can include it in my start-button.
If not, any sugestion on how to solve the problem?
Best regards
Mikael

Include non-cumulative key figure in InfoSpoke

Hi Experts,
I am trying to create InfoSpoke for AR Line Item Cube(0FIAR_C03) with all infoObjects.
This includes non-cumulative key figures such as
0DSCT_DAYS1 (Days for first cash discount)
0DSCT_PCT1 (Percentage for first cash discount)
However, InfoSpoke run failed and following messages is displayed.
Error in SQL Statement: SAPSQL_ILLEGAL_AGGREGATE NOP
Does the infoSpoke not support non-cumulative key figures?
It worked fine when I remove all the non-cumulative key figures from the InfoSpoke.
*I certainly set 1 for 0RECORDTP(Record Type) in the selection tab as SAP Help instructed
Thank you for your answers in advance.

Try OSS Note Number: 850428.

Error while activating cube contains non cumulative key figures

Hi all,
when i am trying to activate a cube which contains non cumulative key figure it is showing out the following error:
DDIC Object TABL /BIC/LZATTR1NON has not been activated
Table /BIC/LZATTR1NON could not be activated
Please let me know if any one come across with such error
Help are appreciated

Before activating an infocube with non-cumulative keyfigures, the system
design forces the user to enter at least once the screen: maintain
non-cumulative values (validity table). If that step has been performed, activation will work fine.
In the meantime, please do this step explicitly, at least once, when
configuring such an infocube, then you should not have any problem.
Please follow the same process while activating the infocube
Goto Infocube ->Goto Change mode->Menu ->Extra-> goto the screen:
maintain non-cumulative values once.
Walter Oliveira.

Defining Working Times - Incorrect Scheduling Result for non-Working Date

Hi All,
We are on SAP R/3 46C and in the process of implementing 'Route Schedules' for our outbound delivery processing.
One of the pre-requisite customising requirements for 'Route Schedules' is to maintain 'Working Times' for the Shipping Point for precise scheduling.
We have defined a 24 hour shift between Monday and Friday in the 'Working Times' config (IMG -> Logistics Execution -> Shipping -> Basic Shipping Functions -> Scheduling -> Delivery Scheduling and Transportation Scheduling -> Maintain Working Hours).
The 24 hour shift is defined as follows Start: 00:00:00 with a Finish at 24:00:00 (We initially had 23:59:59, however, encountered problems with this config). We have also maintained a 24 hour Pick/Pack time in Customising, and we do not use Loading Times.
We have encountered a problem when we key a Sales Order Item where the ATP confirmed qty Delivery Date results in a Material Availability Date on a 'Friday', in this scenario, the system determines a one day 'Loading Time' which falls on a Saturday at 00:00:00. This outcome is incorrect on two levels - 1) we do not use 'Loading Times' in our system, 2) a non-working day (Saturday) has been selected. An important exception to this outcome - if a Route is not selected for the Sales Order item, the outcome described above does not eventuate.
Any assistance in explaing possible causes of this unusual result would be greatly appreciated.
Thanks in advance,
Ravelle
When we display our time streams via report 'ZZTSTRDISP' (OSS Note 169885)
The system shows our 24:00:00 Finish time is converted to 00:00:00 which incorrectly rolls into the next day - on a Friday this means our shift finishes on a Saturday at 00:00:00
25    06.02.2008     00:00:00            07.02.2008     00:00:00
26    07.02.2008     00:00:00            08.02.2008     00:00:00
27    08.02.2008     00:00:00            09.02.2008     00:00:00 <-- Saturday
28    11.02.2008     00:00:00            12.02.2008     00:00:00
29    12.02.2008     00:00:00            13.02.2008     00:00:00
30    13.02.2008     00:00:00            14.02.2008     00:00:00
31    14.02.2008     00:00:00            15.02.2008     00:00:00
32    15.02.2008     00:00:00            16.02.2008     00:00:00 <-- Saturday
33    18.02.2008     00:00:00            19.02.2008     00:00:00

SAP Created OSS Note# 1144784 to resolve this issue for us.

IPhoto quit unexpectedly. Tried different solutions, none worked. Any suggestions?

Hello,
I have a 2012 non-retina Macbook Pro running OSX 10.8.4 and iPhoto '11 version 9.4.3.
My iPhoto was running fine until about a month ago. And just last week when I tried opening it, I got the "iPhoto quit unexpectedly" message. Since then I have tried many solutions as suggested in the forum but none worked for me. Here are the list of things I tried.
1. Tried reopening.
2. Tried to create a new library, but it wouldn't let me create one.
3. Tried holding the cmd + option keys while opening iPhoto had no effect.
4. Tried downloading iPhoto Library Manager and rebuilding. It didn't work.
5. Tried running in safe mode. It didn't work.
6. Tried logging in using Guest account. It didn't work.
7. Tried completely uninstalling iPhoto (including system files and hidden files) and reinstalling. Still didn't work.
8. Tried restoring iPhoto from my Time machine backup from a month ago. No luck.
All these solutions I tried resulted in the same "iPhoto quit unexpectedly" message.
Could somebody please help me out? If you need further information please ask me.
Thank you.

3. Tried holding the cmd + option keys while opening iPhoto had no effect.
What options did you run from the iPhoto Fix window?
2. Tried to create a new library, but it wouldn't let me create one.
Try the following:
1 - delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your
User/Home/Library/ Preferences folder.
2 - delete iPhoto's cache file, Cache.db, that is located in your
User/Home/Library/Caches/com.apple.iPhoto folder (Snow Leopard and Earlier).
or with Lion and Mt. Lion from the User/Library/Containers/com.apple.iPhoto/
Data/Library/Caches/com.apple.iPhoto folder
3 - launch iPhoto and try again.
NOTE 1: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding down the Option key when launching iPhoto. You'll also have to reset the iPhoto's various preferences.
NOTE 2: In Lion and Mountain Lion the Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
OT

Java OracleXML putXML & non-unique keys

I am using the XML SQL Utility for java on the client (NT) to insert multi-row XML documents into an ORACLE table. Everything works fine until I hit a row with a non-unique key. It appears insertXML throws an error and the insert stops at that point. Rows after the non-unique key row are not processed.
Is there any way to process all rows of an XML document, telling me how many read, how many inserted, how many not processed??
Also, what about update capabilities? Presently I am not needing to update from XML into ORACLE, all I can do now is insert.
Thanks in advance,
Rick

One way to make this work would be to take advantage of Oracle8i's INSTEAD OF triggers on views.
Basically, you would:
(1) CREATE VIEW someview
AS SELECT * FROM sometable;
(2) CREATE TRIGGER someview_trig
INSTEAD OF INSERT ON someview
DECLARE
BEGIN
-- Check for existence of
-- row using the value of
-- :NEW.pk_column_name
IF (you-found-an-existing-one) THEN
-- Do something here like
-- NULL; to ignore the insert altogether
-- or possible an INSERT into
-- and EXCEPTIONS table...
ELSE
INSERT INTO sometable
VALUES (:NEW.column1, ..., :NEW.columnn);
END IF;
END;
(3) Then point XML SQL Utility at someview
instead of sometable
and you'll be in business, as they say.

Dependent Requirements are falling on Non Working Day

Hi,
I have my dependent requirements for my ROH material on 15.05.2011 which is a Sunday, Non Working in my Factory Calendar. How is this possible?
Details are as follows.
ROH A MRP type PD is required for FER B MRP Type X0
ROH for FER as per system reqmtn fall on 15.05.2010 which is Sunday. What is wrong in my settings.

Nilesh,
Prasobh has already suggested what you should be investigating. Your finished goods Planned order was (presumably) not generated in ERP. Dependent requirements come from the Planned order.
The Planned order for FER is being generated in an external system (presumably APO, yes?). The start date for this order, and therefore the dependent requirements, are generated somewhere other than ERP. Unless you schedule/reschedule this planned order in ERP, the date generated in the external system will be the date that drives the dependent requirements for the lower level. Regardless of any factory calendars.
I don't know what your external system is. However, before you investigate there, there is one more topic that the other experts haven't asked you, and that is the BOM of your FER material. Look at the BOM for the parent part that is driving your dependent requirement. Look at the details of the item that contains the component that is giving you heartburn. Entries in Lead time offset, Operation LT offset, Distribution key, and Special procurement can have an impact on the dependent requirement date.
If APO is in fact your external system, you should be aware that virtually all of the items mentioned by JH and other experts should be flawlessly replicated in APO, and they have influence over the scheduling of the start dates of the FGs planned orders. In addition, the same items in ERP can also have an impact if you have set up scheduling (re-scheduling) in ERP.
If you are using APO, I suggest a few things to check:
Transactional Consistency between APO and ERP, and especially any blocked queues
Resource in APO. Does it match the ERP info?
PPM or PDS. Does it match your BOM and Routing info?
Factory calendars in APO. Do they match the ERP calendar?
Any Calendar timestreams in APO. Are they up to date?
Also, if you are using APO for your FGs, you might want to post this question in one of the APO forums instead of a PP forum.
Best Regards,
DB49

Non-responsive keys on keyboard.

Hi guys,
I hope someone can help me out figuring out my problem. I have MacBook Pro 13-inch, Late 2011, Processor 2,8 GHz Intel Core i7 Serial Number C02HG0WKDV14 Software OS X 10.9.5 (13F34).
One day I turned my mac on and it had "M" key stuck, it just kept typing this key. I tried resetting SMC, PRAM and all advices on-line with no success so decided to open it and clean it all up.
During the clean up I accidentally pealed off the black foil on the backlit which I thought caused the following issue of various random keys being non-responsive. So I bought new backlit which in the end did not fix it at all.
Bellow are highlighted the non-responsive keys
One thing I noticed that all keys started to work when was on the plane, probably the pressurized cabin made it work.
Do you by any chance have any ideas what is the problem? How can it be fixed? I just can't live airborne
Thank you for your help

The best thing to do would be take it to an Apple store genius bar and have the techs check it out and see what is wrong with the key switches.
By the way, the "pressurized cabin" of a commercial airliner is actually at reduced atmospheric pressure, only about 80% of the pressure at sea level. That should not have a physical affect, but have the techs check out the keyboard.

Lync 2013 call forwarding (working and non-working scenario)

Hi guys!
We are trying to solve a non-working scenario in Lync 2013 voip calling.
SCENARIO 1 that does not work:
Person A with a mobile phone calls Person B who's telephone number is not located on Lync SIP TRUNK. Person B answers the call and then he wishes to transfer this call to Person C. He call Person C until he hears call ringing tone from him
and then he transfer this call to him. When Person C answer the call he does not hear Person A and call get's disconnected after cca. 20seconds.
SCENARIO 2 that does work:
Person A with a mobile phone calls Person B who's telephone number is not located on Lync SIP TRUNK. Person B wishes to transfer this call to Person C who's number is located on Lync SIP trunk. In this scenario he first wait that Person C
answer/accept his call, then he transfer call from Person A to him. This way Person C is able to hear Person A.
Anyway how to figure it out if this is a problem on provider side or on Lync 2013 server side?
with best regards,
bostjanc

Refer support wasn't set to none.
If we change it to none, and restart Mediation service, unfortunatelly there are no differences.
We have also tried editing: C:\Program Files\Microsoft Lync Server 2013\Mediation Server\MediationServerSvc.exe.config
FROM:
<?xml version="1.0" encoding="utf-8"?>
<configuration>
<runtime>
    <generatePublisherEvidence enabled="false"/>
</runtime>
</configuration>
TO:
<?xml version="1.0" encoding="utf-8"?>
<configuration>
<appSettings>
                <add key="20.20.20.20.ReferredBySupported" value="true"/>
    </appSettings>
<runtime>
    <generatePublisherEvidence enabled="false"/>
</runtime>
</configuration>
But that didn't do anything useful.
bostjanc

Non working keys

Similar Messages

Maybe you are looking for