Not able to communicate with My Nomad
I recently put a new hard dri've on my daughter's computer and upgraded from win98 to 2000. I have installed the driver (nomad2drivers.exe) and (Drv_nm2.exe) from Creative's website. I also installed Creative MediaSource. When I connect my daughter's Nomad IIc to the USB port it does not show up as a removable dri've in my computer nor can I see it using MediaSource, but it does show up on the device manager. And the device manager says that the driver is working properly. Why can't I see the MP3 player using my computer or Windows Explorer? I tried to install the Nomad software on my computer which is running XPpro and get the same results. Please help!!
Shay Glass
<STRIKE>Also</STRIKE> my daughter has several 28meg smart media cards that she uses with her Nomad IIc. Is there a firmware update that will allow her to use the whole 28meg insteed of 64meg?
sglass,
In order for the MediaSource to detect the player, you will also need to download and install the NOMAD Pack for Creative NOMAD II/IIc/II MG.
Jason
Similar Messages
-
I am not able to communicate with my instruments
Hello,
I am a graduate student in India. I
am using NI PCI-GPIB card, which we bought nearly one year back. I am using
LabVIEW 6i. For last two days I am not able to communicate with my
instruments (Keithley DMM 196, Keithley current source 220, Lakshore
temperature controller 93C).
1. I started NI488.2 troubleshooting wizard. It says NI488.2 software
presence verified, GPIB hardware presence verified,GPIB interfaces
sequentially varified. This means Card is alright?
2. I started MAX measurement and automation explorer. It lists GPIB0
(PCI-GPIB) under 'devices and interfaces' folder. After selecting this, If
I click at 'scan for instruments', 'Instruments not found' message
appears.
3. You may say that instru
ments had problem. But the same instruments are
working fine with another system with other card.
4. I agin reinstalled PCI GPIB 488.2 driver from the CD. Now It is listing
three instuments out of four. But the GPIB address for these instruments
are
not same as actual address. It also says instrument didn't reply for *IDN?
query.
5. Everything was working alright, this problem arose few days back
suddenly.
please help meDear sir,
Really something surprising. My instument is 'LakeShore DRC-93C'
temperature controller. Probably bought around 7-8 years back.
Here is the actual GPIB add & address read by MAX and correponding
three NI-SPY log.
actual GPIB add*****address read by MAX*****Max Capture(attached files)
25***** 9*****capture_1
21***** 5*****no file attached
20***** 4*****capture_2
17***** 1*****no file attached
10***** instrument not found****capture_3
7*****instrument not found*****no file attached
for first four cases MAX showed 'instrument did not reply to *IDN? query?
Same thing happened when I connected an Keithely Current Source.
(only one instrument is connected,)
actual GPIB add*****address read by MAX
8*****instrument not found
17***** 1
25***** 9
This means MAX is reading GPIB number 16 less than actual Number? Then I tried
to write command at both GPIB address(actual and read by MAX) but both didn't work?
What should I do next?
with best regards
Ram Shanker
Attachments:
Capture_1.spy 23 KB
Capture_2.spy 23 KB
Capture_3.spy 13 KB -
After an recent OS7 update my iPad2 requested a restore which I did, at the end my iPad jumped into "communicating with iTune" but it never communicates. I restored 3 time alreaady and I am not able to communicate with iTune to be able to use my iPad which is my working tool.
What should I do?Communicate with iTunes? What does this mean? Tell us what you are seeing on your screen and what you then try to do?
-
I am a developer creating an application (web app) which communicates which between flash and javascript. I am not able to call flash functions from javascript. Same code was working earlier....
Can anyone please guide me in the right direction.
Regards
RishiA good place to ask advice about web development is at the MozillaZine "Web Development/Standards Evangelism" forum.
*http://forums.mozillazine.org/viewforum.php?f=25
The helpers at that forum are more knowledgeable about web development issues.<br>
You need to register at the MozillaZine forum site in order to post at that forum. -
SOA_server1 not able to communicate with AdminServer
Hi Everybody,
I am trying to setup SOA environment on my laptop, i am stuck with this following problem , It will be great help if somebody suggest me some solution.
problem Description:
1) I started SOA admin server using startManagedWeblogic.cmd on my windows its starting fine with out any issues.
2) when I started soa_server1 using following command
C:\Oracle\Middleware\user_projects\domains\soadomain\bin>startManagedWebLogic.cm
d soa_server1 http://myalya_pc:7001
following is the error i am getting on the console
Unable to establish JMX Connectivity with the Adminstration Server AdminServer at service:jmx:t3://[
2001:0:4137:9e76:1093:2f13:9ce0:460c]:7001/jndi/weblogic.management.mbeanservers
.domainruntime.
interestingly server is running are ready to accept the requests .
here are my questions related to this subject.
1) How to make this error go away.
2) is it really mandatory that "soa_server1" managed server should communicate with AdminServer to build and test Oracle composite applications ?
i look forward to hear back from Oracle SOA gurus .
regards,
Mlya.startManagedWebLogic.cmd soa_server1 http://localhost:7001
So was it really was due to the IPv6 address then?
Earlier you were using
startManagedWebLogic.cmd soa_server1 http://Suhel-PC:7001
If you open your hosts file, you might see that Suhel-PC is mapped to the IPv6 address
2001:0:4137:9e76:1093:2f13:9ce0:460c (before an IPv4 address?) OR getting bound to an IPv6 address via DHCP because IPv6 is enabled on your machine.
While localhost is mapped to 127.0.0.1 (before 0::1)
And due to your version of java, the following connection failed:
jmx:t3://[2001:0:4137:9e76:1093:2f13:9ce0:460c]:7001/jndi/weblogic.management.mbeanservers.domainruntimeWhile now your connection might be using:
jmx:t3://[127.0.0.1]:7001/jndi/weblogic.management.mbeanservers.domainruntime -
My LAP1522HZ is not able to communicate with controller.
Hi All,
one of my company's Project ,I need to configure LAP1522 series Lightweight AP. When I connect my LAP to switch port .It pull out IP address from DHCP.I configured DHCP option 43 on that subnet.All Other lightweigh APs are working fine.When I ping that Ip address from the switch where I configured LAP it just give 100% loss.Also MAC-Address on that port show me two mac-address entry from that port.Please let me know If you experienced same issue in the past and any solutions on this.
Device ID: APc40a.cb68.6320
Entry address(es):
IP address: 10.38.114.36
Platform: cisco AIR-LAP1522HZ-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet1/0/26, Port ID (outgoing port): GigabitEthernet0
Holdtime : 108 sec
Version :
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 13:15 by prod_rel_team
advertisement version: 2
Duplex: full
Power drawn: 10.200 Watts
Power request id: 38703, Power management id: 1
Power request levels are:0 0 0 0 0
Management address(es):
ping 10.38.114.36
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.38.114.36, timeout is 2 seconds:
Success rate is 0 percent (0/5)
sh mac-address-table int fa1/0/26
Mac Address Table
Vlan Mac Address Type Ports
23 c40a.cb68.6320 DYNAMIC Fa1/0/26
23 c40a.cb68.641c DYNAMIC Fa1/0/26
Total Mac Addresses for this criterion: 2
I just configured similar LAP on neighboring port and it works fine.
sh cdp neig fa1/0/21 detail
Device ID: ........(Name of LAP)
Entry address(es):
IP address: 10.38.114.35
Platform: cisco AIR-LAP1522HZ-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet1/0/21, Port ID (outgoing port): GigabitEthernet0
Holdtime : 160 sec
Version :
Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 13:15 by prod_rel_team
advertisement version: 2
Duplex: full
Power drawn: 10.200 Watts
Power request id: 7043, Power management id: 1
Power request levels are:0 0 0 0 0
Management address(es):
ping 10.38.114.35
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.38.114.35, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
sh mac-address-table int fa1/0/21
Mac Address Table
Vlan Mac Address Type Ports
23 0023.ac1a.3f00 DYNAMIC Fa1/0/21
Total Mac Addresses for this criterion: 1I cant do that.It's production switch and dont want to reset ARP entries.
Regards,
Atit Patel -
Sensor Not able to communicate
I have an IDSM running Sensor version 4.1(4) and Signature S174. It was working perfectly untill few days back . But When telneted in to the IDSM it logs in and logs out instantly showing the error message "Not able to communicate with the Process". The RDEP connection with the VMS is also showing not connected .I tried accessing the sensor through the web browser through https but with No luck. The IDSM status seems to be fine when checked from the MSFC . I tried resetting the IDSM through MSFC. But its still the same. Can anything done to troubleshoot to know what has happened?
The Sensor was working fine for 15 days after the S174 Upgrade and the problem started suddenly. My sensor is IDSM2 which is loaded on a 6509 chasis.There is no external connection except the shutdown button.Packets to be captured are diverted onto the IDSM through MSFC.The MSFC config related to IDSM seems to be unaltered.
I am attaching the related config of MSFC .This may help Understand the problem better.
intrusion-detection module 8 management-port access-vlan 17
intrusion-detection module 8 data-port 2 capture
intrusion-detection module 8 data-port 2 capture allowed-vlan 2,4-7,11,16-25
intrusion-detection module 8 data-port 2 capture allowed-vlan 50,51,1002-1005
vlan access-map captureall 10
match ip address idsmon
action forward capture
ip access-list extended MATCHALL
permit ip any any
ip access-list extended idsmon
permit ip any any
VLAN 17 is my management VLAN .IDSM has the Management IP in the same VLAN. -
when I try to print, I get this error message "Communications Failure: The computer is no longer able to communicate with your printer. " followed by intruictions to turn off the printer and check connections etc. I am using an HP Officejet 6500 709e, connecter wirelessly
I'm using a mac (OS X - snow leopord) and am printing over the network (wirelessly).
HP Photosmart Premium Fax All in One - C410a
I was only able to print one page and then both my printer and my computer would display an error message about the printer's inability to print. Since then I've been able to resolve my specific problem.
I
1. uninstalled HP from my computer (checked to ensure that my printer was no longer visible in my printers and the HP Utility software was nowhere to be found),
2. grabbed the software/driver update from Aug, 2010,
3. installed the Aug, 2010 update, and my problems seem to have been fixed.
This is where I got my 2010 update from (obviously you should get the driver/software applicable to your OS and specific printer):
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-85379-1&cc=us&dlc=en&lc=en&... -
Communication Failure: The computer is no longer able to communicate with your printer.
Hello, I have a HP Officejet J6480 All-in-One printer. When I try to print, I receive this error message:
"Communication Failure: The computer is no longer able to communicate with your printer. Turn the printer off, check your printer connections and check for printer errors, and turn the printer back on."
I am using a Mac PowerBook G4, OS v10.5.7. I have tried the following:
-- rebooted my Mac
-- turned printer off/on
-- rebooted wireless router
-- tried to print using USB cable.
I continue to receive the same error message. Helllllllllllllllp!!!!
A couple of other things I need to mention: I bought this printer in June and have been able to print just fine since purchasing
this printer. As recently as Friday, July 3, I was able to print and printed 6 or 7 pages then. This is CRAZY!!!!
Thanks.
Barb
Message Edited by BarbNPhx on 07-05-2009 10:55 AMI'm using a mac (OS X - snow leopord) and am printing over the network (wirelessly).
HP Photosmart Premium Fax All in One - C410a
I was only able to print one page and then both my printer and my computer would display an error message about the printer's inability to print. Since then I've been able to resolve my specific problem.
I
1. uninstalled HP from my computer (checked to ensure that my printer was no longer visible in my printers and the HP Utility software was nowhere to be found),
2. grabbed the software/driver update from Aug, 2010,
3. installed the Aug, 2010 update, and my problems seem to have been fixed.
This is where I got my 2010 update from (obviously you should get the driver/software applicable to your OS and specific printer):
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-85379-1&cc=us&dlc=en&lc=en&... -
Datareader is not able to connect with database-Urgent
Hi All,
All of a sudden the Datareader component in my ML experiment is not able to connect with database with the following error:
[ModuleOutput] DllModuleHost Error: 1 : Program::Main encountered fatal exception: Microsoft.Analytics.Exceptions.ErrorMapping+ModuleException: Error 0000: Internal error ---> System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.ArgumentException: The value's length for key 'password' exceeds it's limit of '128'.
Module finished after a runtime of 00:00:00.2031339 with exit code -2
Module failed due to negative exit code of -2
It complains about the password being long-but the same credentials I have been using for the last 2 months and still able to use it to run sql queries on that same database using the management portal.
It appears that Azure encrypts the password and that encrypted password is too long...just my guess after looking that the output.Inside Ml it just says as internal error
Would appreciate if someone can point to the issue at the earliest...(There is a demo early next week)
Subscription:Enterprise,
LOCATION: East Asia
Regards,
BiswajitHi,
Please check this url:
https://studio.azureml.net/Home/ViewWorkspace/bc85d4f81d2246c4b1430eb395229a3a?&hashSeg=#Workspaces/Experiments/Experiment/bc85d4f81d2246c4b1430eb395229a3a.f-id.11776ae4400f4c1aa9f58308c30810fa/ViewExperiment
which is an experiment which I created doing save as of the experiment in which the data reader works.
I stripped everything except the data reader and setup the rest of the components...I finally have to write the results back ,so also pulled a Writer component.
Now,the data reader works fine..but the Writer fails:
Error 0071: Incorrect username "acnadmin" or password is passed
Strangely,its the same credentials set in the DataReader.
Looks like all the DataInput/Output components created recently only have the problem.
Once again,while the datareader in this case passes the password in plain text,the writer encrypts,hence fails. -
I am not able to connect with Itunes Match. I constantly receive the message error 4010
I am not able to connect with Itunes Match. I constantly receive the error 4010.
I can run the general "Update iTunes Match" from the menu but cannot add individual tracks by right-clicking (control-clicking) on them the way I usually do. Then I get the 4010 error message.
Based on other posts here, I can assume the problem is not just me. -
I am not able to connect with another ipod via bluetooth can u pls help me
i am not able to connect with another ipod via bluetooth can u pls help me
Are yo trying to pair via an app that supports BT pairing? If you are I would try:
- Resetting the iPod:
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
-Resetting network settings on the iPod: Settings>General>Reset>Reset Network Settings -
BAPI not able to connect with Livecache
Hello All,
I am using "BAPI_PIRSRVAPS_GETLIST" .
But not get pegging detail. When I debug it is not able to connect with livecache.
How to use BAPI FM in Program, How to connect with livecache ?
Anybody has sample ABAP program for this ?
Thanks in Advance
AmishaHi All,
When I try to use BAPI <b>BAPI_PIRSRVAPS_GETLIST</b> I am not getting pegging information, please help me.
Thanks,
Srinivasa. -
Not able to connect with iTunes
its has been 6 days already and i am not able to connect with itunes to purchase something.
i have used visa and mastercard and i also have money credited to my account.
please help!Hello FoxyNix
Check out the steps below to troubleshoot you issue with connecting to the iTunes Store on your iPhone
Can't connect to the iTunes Store
http://support.apple.com/kb/ts1368
Troubleshoot issues on an iPhone, iPad, or iPod touch
If you haven't been able to connect to the iTunes Store:
Make sure your date, time, and time zone are correct in Settings > General > Date & Time. Note: Time Zone may list another city in your time zone.
Make sure that your iOS software is up to date by tapping Settings > General > Software Update (iOS 5 or later) or connecting your iOS device to iTunes and clicking Check for Update on your device's Summary page.
Check and verify that you're in range of a Wi-Fi router or base station. If you're on a device with cellular service, make sure that cellular data is turned on from Settings > General > Cellular. Note: If connected to cellular data, larger items may not download. You may need to connect to Wi-Fi to download apps, videos, and podcasts.
Make sure that you have an active Internet connection. You can check the user guide for your device for help with connecting to the Internet.
Make sure that other devices (portable computers, for example) are able to connect to the Wi-Fi network and access the Internet.
Try resetting (turning off and then on again) your Wi-Fi router.
If the issue persists, try troubleshooting your Wi-Fi networks and connections.
Regards,
-Norm G. -
Not able to connect with Sql Server Database
Hi,
I'm not able to connect with Sql Server database.during making connection I'm getting the following error:
"Status : Failure -I/O Error: SSO Failed: Native SSPI library not loaded. Check the java.library.path system property."
Please help
Regards,
Neeraj GoelHi,
I'm using Sql Server 2000.
I downloaded the driver from the given site and still having the same problem. Do I need to copy the driver file in some specific folder.
Regards,
Neeraj Goel
Maybe you are looking for
-
Creation of New field in Relationship block of contact page
Hi, I have created a new field as value attribute in Relationship block of contact overview page. Since both AET and EEWB did not allow creation of the field as part of BUT051 I had to create value atribute. I have custom logic for the field. Can you
-
Itunes freezes on ipod, and won't play or update
I have the newest itouch, and it has frozen in the middle of playing (songs were on shuffle mode) and gotten stuck. The program appears to be frozen, as I can't switch tracks, and the itunes is stuck on the playlist page, and won't respond at all. I
-
WHAT VERSION IS MY 500GB TIMECAPSULE
Hi, im a little confused at what version I have of my 500GB TimeCapsule, on the box it says:MB764B/A Model No = A1302, is this the late 2009 model? Thankyou
-
The .prel files will not load into premiere elements 13 and says that there is a missing codec. This is a school's site llicense that we've used in our lab for more than a month.
-
I need to select somehow to import only jpeg images from my Canon 5D Mk11 camera to an iPad 2 I take photographs in both RAW (high quality up to 30Mb file size) and JPEG low quality for use on iPad and Internet. The Raw files I save to a 1Tb Multimed