Not able to configure SSH
Hi,
I'm using 1841 router.My question is I'm not able to configure SSH in this router ,Any IOS problem?
Sh version
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SO
FTWARE (fc1)
Hi Karthick
You are currently running IP BASE Feature Set ios on your router you need to upgrade the same to Advanced Security Services or SP Services Feature set to have SSH support in your router..
http://www.cisco.com/en/US/products/sw/iosswrel/ps5460/index.html
regds
Similar Messages
-
i purchased i phone 3GS from San francisco thro my brother, when i brought to oman, i want to update ios 5 to ios 6 for that from itunes to start update , finally failed and i could not able to configure in oman wifi network, i dont have backup..help me..
Has your phone ever been hacked or jailbroken. This error message is what usually shows up for that. Are you using a supported carrier for the iPhone, or did someone hack the phone to unlock it to be used on another carrier. If that is the case, then there is no help you can get here as discussing hacked/jailbroken devices is not allowed.
-
HT1414 just got iPad 3.. not able to configure
just got iPad 3.. not able to configure.. not able to connect to WiFi, at my location WiFi network exists with proxy settings.. pls Help
I'd talk to your school tech support and see what settings they have in place. For example, I can't access my work's e-mail via the exchange app but I can via the web access...largely because it's not a work iPad and they won't allow that kind of access on a device that's not 'their own'
-
Iphone is not detecting network after updating, i m not able to configure it
my iphone is not detecting network after updating, i m not able to configure it
To answer your question there, are you unable to connect to cellular internet (using a SIM or WiFi?
-
I am not able to configure settings the helpdesk properly.How can it be done?
i am not able to configure settings the helpdesk properly.How can it be done?
This topic first appeared in the Spiceworks Communityi am not able to configure settings the helpdesk properly.How can it be done?
This topic first appeared in the Spiceworks Community -
I' m not able to configure email. I can send messages but I can't receive them
I need your help.....I'm not able to configure email....I can send messages but I can't receive them
iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
iPad Mail
http://www.apple.com/support/ipad/mail/
Cheers, Tom -
Re: Dynadock not able to configure properly external monitor
Dear Sir/Madam,
I found a problem with my Dynadock (PA3541EY1PRP) in terms that it is not able to configure properly the monitor (LG Flatron E2250V-PN).
I would make clear that my PC is working under win 7 64bit.
Thanks oodles for your support.
Regards
MAxok,
when I connect VGA cable to the dynadock, external monitor apperas to be in low resolution.
Checking in the "screen resolution", windows shows "no monitor" (can I attach a file to show the screenshot?) and the maximum resolution is set at 1440X900. Therefore, I am forced to connect directly the external monitor to the pc. In this case the monitor is properly recognized as "VGA monitor" and the resolution appears to be rightly set at 1920X1080.
thanks -
Hi
I configured Cisco ASA5510 firewall, but i am facing the problem with ssh login, i gave ssh for inside and outside access, but i am getting "server ... error" i enabled LOCAL for the authentication for ssh and HTTP. and i am able to acees the device through HTTP using ASDM, but not able to access from outside.
please find the configuration
thanks in advance
regards
Javahar
ASA Version 8.2(1)
hostname ASA5510
domain-name default.domain.invalid
enable password Nbxmt7LFbcxtLo.o encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 10.251.38.0 SAP_remote
interface Ethernet0/0
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Ethernet0/1
nameif outside
security-level 0
ip address xxx.xxx.xxx.xxx 255.255.255.252
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 SAP_remote 255.255.255.128
access-list outside_cryptomap extended permit ip 192.168.1.0 255.255.255.0 SAP_remote 255.255.255.128
access-list outside_cryptomap_1 extended permit ip 192.168.1.0 255.255.255.0 SAP_remote 255.255.255.128
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 115.115.169.241 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_cryptomap_1
crypto map outside_map 1 set peer XXX.XXX.XXX.20
crypto map outside_map 1 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 2 match address outside_cryptomap
crypto map outside_map 2 set pfs group5
crypto map outside_map 2 set peer XXX.XXX.XXX.20
crypto map outside_map 2 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map interface outside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 5
lifetime 28800
http server enable
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outsde
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 outsde
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
username test1234 password /FzQ9W6s1KjC0YQ7 encrypted
username cisco1234 password 5sSb..e9ZNWMmk2e encrypted privilege 15
tunnel-group Remote-p2p-vpn type ipsec-l2l
tunnel-group Remote-p2p-vpn ipsec-attributes
pre-shared-key *
tunnel-group XXX.XXX.XXXX.20 type ipsec-l2l
tunnel-group XXX.XXX.XXXX.20 ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
message-length maximum client auto
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:83eab0b7ae2d2d9e74f8ea0b005076ea
: endHi,
Did you issue the command
ASA(config)# crypto key generate rsa modulus 2048
So that you can use SSH.
EDIT: I would suggest narrowing down the source address from where you can connect to the ASA from "outside" if possible.
- Jouni -
Not able to enable SSH user equivalency for RAC on RHEL 4
Hi All,
I am trying to install oracle RAC 11g on RHEL4 (on VMware), I am using below document for reference.
http://www.oracle-base.com/articles/11g/OracleDB11gR1RACInstallationOnOEL5UsingVMware.php
Every thing went fine till "SSH user equivalency", but I am not able to SSH and SCP between servers without entering passwords.
I have tried removing .ssh folder & recreating pub file twice but it did not helped.
am i missing something?
Please advice.
Thanks,
Abhay.Configure SSH on each node in the cluster. Log in as the "oracle" user and perform the following tasks on each node.
su - oracle
mkdir ~/.ssh
chmod 700 ~/.ssh
/usr/bin/ssh-keygen -t rsa # Accept the default settings.
The RSA public key is written to the ~/.ssh/id_rsa.pub file and the private key to the ~/.ssh/id_rsa file.
Log in as the "*oracle*" user on RAC1, generate an "authorized_keys" file on RAC1 and copy it to RAC2 using the following commands.
su - oracle
cd ~/.ssh
cat id_rsa.pub >> authorized_keys
scp authorized_keys rac2:/home/oracle/.ssh/
Next, log in as the "oracle" user on RAC2 and perform the following commands.
su - oracle
cd ~/.ssh
cat id_rsa.pub >> authorized_keys
scp authorized_keys rac1:/home/oracle/.ssh/
The "authorized_keys" file on both servers now contains the public keys generated on all RAC nodes.
To enable SSH user equivalency on the cluster member nodes issue the following commands on each node.
ssh rac1 date
ssh rac2 date
ssh rac1.localdomain date
ssh rac2.localdomain date
exec /usr/bin/ssh-agent $SHELL
/usr/bin/ssh-add
You should now be able to SSH and SCP between servers without entering passwords.
hope, this may helps you.
enjoy.
if you are unable to resolve it, please refer:-
http://download.oracle.com/docs/cd/B28359_01/rac.111/b28252/preparing.htm#BGBBDHIB
http://dsstos. blogspot.com/2009/03/linux-oracle-rac-and-bonding-conundrum.html -
Not able to configure IDM 11.1.1.7 in RHEL
Hi,
Installed below componnets in silent mode
Java 1.6
WLS 10.3.6
IDM 11.1.1.7
while configuring IDM(for OIF) in silent mode based from response file, it is getting stuck at CREATE DOMAIN. In Install out file, log says starting domain and it stays there for long time. But I am not able to continue further.
I am seeing below warnings in install log file
[2015-03-18T16:41:57.229-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/modules/com.bea.core.weblogic.security.identity_1.1.2.0.jar
[2015-03-18T16:41:57.230-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/patch_wls1032/profiles/default/sys_manifest_classpath/weblogic_patch.jar
[2015-03-18T16:41:57.238-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/jrockit_160_14_R27.6.4-18/lib/tools.jar
[2015-03-18T16:41:57.285-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/wlserver_10.3/server/lib/weblogic_sp.jar
[2015-03-18T16:41:57.286-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/modules/features/weblogic.server.modules_10.3.2.0.jar
[2015-03-18T16:41:57.287-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/modules/org.apache.ant_1.7.0/lib/ant-all.jar
[2015-03-18T16:41:57.287-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/modules/net.sf.antcontrib_1.0.0.0_1-0b2/lib/ant-contrib.jar
[2015-03-18T16:41:57.287-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/wlserver_10.3/common/eval/pointbase/lib/pbembedded57.jar
[2015-03-18T16:41:57.288-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/wlserver_10.3/common/eval/pointbase/lib/pbclient57.jar
[2015-03-18T16:41:57.288-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/wlserver_10.3/common/eval/pointbase/lib/pbtools57.jar
[2015-03-18T16:41:57.312-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/modules/org.apache.ant_1.7.0/lib/ant-all.jar
[2015-03-18T16:41:57.343-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/modules/org.apache.ant_1.7.0/lib/ant.jar
[2015-03-18T16:41:57.344-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/modules/org.apache.ant_1.7.0/lib/ant-launcher.jar
[2015-03-18T16:41:57.344-04:00] [as] [WARNING] [] [oracle.as.install.engine.modules.configuration.client.ConfigActionClassLoader] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [Action]: Bootstrap Domain Configuration. Library not found: /opt/weblogic/middleware11g/modules/features/weblogic.server.modules_10.3.1.0.jar
Admin Server is coming up after long time and I am able to access weblogic console.
But in logs, it trys to connect to admin server and says could not connect.
[2015-03-18T17:52:29.787-04:00] [as] [TRACE] [] [oracle.as.provisioning] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [SRC_CLASS: oracle.as.idm.install.config.event.IdMProvisionEventListener] [SRC_METHOD: onConfigurationStatus] [OOB IDM CONFIG EVENT] onConfigurationStatus ->23389ae6-ec6d-4830-b97e-2510c75ad281 StatusMsg:Connecting to AdminServer.
[2015-03-18T17:52:29.787-04:00] [as] [NOTIFICATION] [] [oracle.as.provisioning] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] reportStartConfigAction: EXIT........
[2015-03-18T17:52:29.788-04:00] [as] [ERROR] [] [oracle.as.provisioning] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [[
java.io.IOException
at weblogic.management.remote.common.ClientProviderBase.makeConnection(ClientProviderBase.java:196)
at weblogic.management.remote.common.ClientProviderBase.newJMXConnector(ClientProviderBase.java:84)
at javax.management.remote.JMXConnectorFactory.newJMXConnector(JMXConnectorFactory.java:338)
at javax.management.remote.JMXConnectorFactory.connect(JMXConnectorFactory.java:247)
at oracle.as.provisioning.weblogic.AdminServer.connect(AdminServer.java:98)
at oracle.as.provisioning.weblogic.ASDomain._connectToAdminServer(ASDomain.java:409)
at oracle.as.provisioning.weblogic.ASDomain.connectToAdminServer(ASDomain.java:363)
at oracle.as.provisioning.engine.WorkFlowExecutor.executeWLSWorkFlow(WorkFlowExecutor.java:411)
at oracle.as.provisioning.engine.Config.executeConfigWorkflow_WLS(Config.java:866)
at oracle.as.idm.install.config.BootstrapConfigManager.doExecute(BootstrapConfigManager.java:1088)
at oracle.as.install.engine.modules.configuration.client.ConfigAction.execute(ConfigAction.java:375)
at oracle.as.install.engine.modules.configuration.action.TaskPerformer.run(TaskPerformer.java:88)
at oracle.as.install.engine.modules.configuration.action.TaskPerformer.startConfigAction(TaskPerformer.java:105)
at oracle.as.install.engine.modules.configuration.action.ActionRequest.perform(ActionRequest.java:15)
at oracle.as.install.engine.modules.configuration.action.RequestQueue.perform(RequestQueue.java:96)
at oracle.as.install.engine.modules.configuration.standard.StandardConfigActionManager.start(StandardConfigActionManager.java:186)
at oracle.as.install.engine.modules.configuration.boot.ConfigurationExtension.kickstart(ConfigurationExtension.java:81)
at oracle.as.install.engine.modules.configuration.ConfigurationModule.run(ConfigurationModule.java:86)
at java.lang.Thread.run(Thread.java:662)
Caused by: javax.naming.ServiceUnavailableException [Root exception is java.net.UnknownHostException: vsvphxoamdev01.hotelgroup.com]
at weblogic.jndi.internal.ExceptionTranslator.toNamingException(ExceptionTranslator.java:34)
at weblogic.jndi.WLInitialContextFactoryDelegate.toNamingException(WLInitialContextFactoryDelegate.java:792)
at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:366)
at weblogic.jndi.Environment.getContext(Environment.java:315)
at weblogic.jndi.Environment.getContext(Environment.java:285)
at weblogic.jndi.WLInitialContextFactory.getInitialContext(WLInitialContextFactory.java:117)
at javax.naming.spi.NamingManager.getInitialContext(NamingManager.java:667)
at javax.naming.InitialContext.getDefaultInitCtx(InitialContext.java:288)
at javax.naming.InitialContext.init(InitialContext.java:223)
at javax.naming.InitialContext.<init>(InitialContext.java:197)
at weblogic.management.remote.common.ClientProviderBase.makeConnection(ClientProviderBase.java:178)
... 18 more
Caused by: java.net.UnknownHostException: vsvphxoamdev01.hotelgroup.com
at java.net.InetAddress.getAllByName0(InetAddress.java:1157)
at java.net.InetAddress.getAllByName(InetAddress.java:1083)
at java.net.InetAddress.getAllByName(InetAddress.java:1019)
at weblogic.rjvm.RJVMFinder.getDnsEntries(RJVMFinder.java:422)
at weblogic.rjvm.RJVMFinder.findOrCreateInternal(RJVMFinder.java:192)
at weblogic.rjvm.RJVMFinder.findOrCreate(RJVMFinder.java:170)
at weblogic.rjvm.ServerURL.findOrCreateRJVM(ServerURL.java:165)
at weblogic.jndi.WLInitialContextFactoryDelegate$1.run(WLInitialContextFactoryDelegate.java:345)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:146)
at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:340)
... 26 more
[2015-03-18T17:52:29.789-04:00] [as] [TRACE:16] [] [oracle.as.provisioning] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [SRC_CLASS: IdMProvisioningEventListener] [SRC_METHOD: onConfigurationError] ENTRY 23389ae6-ec6d-4830-b97e-2510c75ad281
[2015-03-18T17:52:29.789-04:00] [as] [TRACE] [] [oracle.as.provisioning] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [SRC_CLASS: oracle.as.idm.install.config.event.IdMProvisionEventListener] [SRC_METHOD: onConfigurationError] ________________________________________________________________________________
[2015-03-18T17:52:29.789-04:00] [as] [TRACE] [] [oracle.as.provisioning] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [SRC_CLASS: oracle.as.idm.install.config.event.IdMProvisionEventListener] [SRC_METHOD: onConfigurationError] [OOB IDM CONFIG EVENT] onConfigurationError -> configGUID 23389ae6-ec6d-4830-b97e-2510c75ad281
[2015-03-18T17:52:29.790-04:00] [as] [TRACE] [] [oracle.as.provisioning] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [SRC_CLASS: oracle.as.idm.install.config.event.IdMProvisionEventListener] [SRC_METHOD: onConfigurationError] [OOB IDM CONFIG EVENT] ErrorID: 35006
[2015-03-18T17:52:29.790-04:00] [as] [TRACE] [] [oracle.as.provisioning] [tid: 13] [ecid: 0000Kkibk_c2JRS_uDs1yX1L2UCH000004,0] [SRC_CLASS: oracle.as.idm.install.config.event.IdMProvisionEventListener] [SRC_METHOD: onConfigurationError] [OOB IDM CONFIG EVENT] Description: [[
Unable to connect to the AdminServer.
Cause:
An internal operation has failed:java.io.IOException
Action:
See logs for more details.I have verified host file entry also. It looks fine
-bash-4.1$ cat /etc/hosts
127.0.0.1 localhost.localdomain localhost
10.86.60.229 vsvphxoampoc01.hotelgroup.com
10.86.231.100 phxasn4_bu
10.86.240.204 phxasn4
::1 localhost loopback -
Not able to configure Act As in OBIEE 11g - The application is logging out
Hi All,
We are trying to configure Act As in OBIEE 11g. The list of users gets populated when I click on Act As. However, when I select any user from the list, the applications logs out. The possible reason could be that OBIEE is not able to authenticate the user (We are using table based Authentication). Please give some pointers to fix it.
Also, I am curious to understand the authentication process in case of Act As. The list that gets populated is a list of target users from the table. In our case, the username and display name gets populated. But, how does OBIEE check if that is a valid user or not?
Thanks in Anticipation,
KaranDoes Act As functionality work with BI Publisher? I am able to login and select Act As and pick a user and view all dashboards, however when I click a PDF embedded in a dashboard page from Publisher, it says Unauthorized Access: please contact the administrator. If I am logged in as myself I can view the PDF. If I am logged in as the user I acting as I can view the pdf, but if I login as myself and act as that user and try and view it, that is when the error occurs, so am wondering is Act As is incompatible with BI Pub.
-
Hi,
I have updated the android version of my phone to the latest of kitkat (14.3.A.0.757). After which configuring the exchane mail (corporate mail account) but it is not configuring. Every time it keeps 'checking incoming server settings' for indefinite time. I thought it might be taking time so i left the phone in the same situation for overnight but no result in morning. It looks like a bug in the latest version of kitkat on Xperia. Please suggest a solution.Hi and welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
First make sure that you have a working Internet connection in the phone.
You can download Internet and MMS settings for your phone by going to Setting > More > Internet settings.
If you have a working Internet connection but still not able to connect to your E-mail server or sync your E-mails check that no Proxy server within your APN settings may be blocking this. You can check this by going to Settings > More (Wireless & networks) > Mobile networks > APN or Access Point Names > Your Internet APN. Check if any details are set for Proxy and Proxy port. If yes you can try to delete them (temporarily) and save the APN. Now check if you’re able to connect or sync with your E-mail server.
You can also verify suspected Internet connection issues by trying via a Wi-Fi network instead.
- Community Manager Sony Xperia Support Forum
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page. -
Adobe Configuration manager is not able to configure Oracle Database
Hi,
I am trying to configure and test data base connection using adobe livecycle configuration manager.
I am sure that my all oracle database credials (db type,db name, host name, port number , db userid and password) are correct.
but not sure about JDBC driver in application server lib and local JDBC driver path.
When i click on Test Database Connection it gives me error message "database setting failed validations".
Please help me knowing the issue. Why i am not able to connect to Oracle data base.
I have three servers
1. Adobe LC server ( First I installed Weblogic and then adobe lc)
2. weblogic server (only weblogic is installed, created database and gave privilages as per clustering_weblogic.pdf document)
3. Oracle Database (only oracle is installed, using Net manager , entering userid and password connection is successfull)
Please let me know issue.
Regards
Sunil GuptaHina,
ok, before i further move. I just want to confirm data base if evething is all right...
I created on database using configuration assistant tool in oracle.
DataBase Name : adobe_lc
SID: adobelc
port :default is 1521
userid :system
password:xxxxx
hostname: ip address or maachine name with domain.
then i assigned following privilages to user account system
●
CREATE SEQUENCE
●
CREATE VIEW
●
UNLIMITED TABLESPACE
●
CREATE TABLE
●
CREATE CLUSTER
●
CREATE SESSION
i assigned privilages by login into https://hostname.domain:5500/em.
Question:
Above url i got when i open database from start->oracle home->created db.
should this 5500 and port number same???
When i test it using "Net Manager" in oracle database, using userid and password it is tested successfully.
so i think there is no issue with the database. I mean to say, then there is no issue at oracle database side correct?
please let me know if anything else need to be tested on database. because before i proceed further i want to confirm that my database is correct in all aspect and ready to be configured with weblogic.
Regards
sunil gupta -
In windows2012, IIS is not able to configure in Microsoft Failover Cluster
Hello All
I configured IIS under Microsoft Failover Cluster with the help of below link. The setup is working successful. I configured this on Windows2008.
http://support.microsoft.com/kb/970759/en-us
I verified below as test cases.
1.) I kill PID of W3SVC , the failover executed.
2.) I stopped the Default Web Site, the failover executed.
3.) I stopped the Default Application Pool, the failover executed.
4.) I stopped the other Application Pools, the failover executed(after changing the script under above mentioned link).
PLEASE NOTE: I used the following links to configure the setup on Windows2008 and Windows2012
http://zahidhaseeb.wordpress.com/2014/02/12/how-to-configure-iis-web-site-and-application-pool-in-microsoft-failover-cluster/
But, when I create the same environment under Windows2012, see what happen below.
I verified below as test cases.
1.) I kill PID of W3SVC , the failover executed.
2.) I stopped the Default Web Site, the failover executed.
3.) I stopped the Default Application Pool, the failover executed.
4.) I stopped the other Application Pools, the failover is not executed(after changing the script under above mentioned link).
Any comment will be appreciated. Thanks. Zahid Haseeb.Hi,
As the KB mentioned, Microsoft recommends administrators carefully evaluate the use of Network Load Balancing (NLB) as the primary and preferred method for improving the scalability and availability of Web applications with multiple servers running IIS 7.5
or IIS 7.0, as opposed to using failover clustering.
It is important to consider that clustering IIS by means of clustering the IIS services does not always guarantee a high availability solution for Web applications.
While the IIS services (specifically the WWW service) might be up and running, a specific application pool’s hosting process could have terminated, or the application might be throwing internal server HTTP errors. Clustering the Web applications and
monitoring their health by using a custom script is the correct and recommended way to achieve a high availability IIS cluster using failover clustering. Below is a sample script that monitors the state of an application pool to determine if it is started
or not.
That’s more about the IIS issue, maybe you can ask more detail question in IIS forum.
IIS support forum
http://forums.iis.net/
Thanks for your understanding and support.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
HI
Now there is an issue while iam running powershell script for BDC service.
Below is the script i am using to configure BDC service.
Param(
[Parameter(Mandatory=$true,ValueFromPipeline=$true)]
[string]$ServiceName = $null,
[Parameter(Mandatory=$true)]
[string]$ServiceProxyName = $null,
[Parameter(Mandatory=$true)]
[string]$AppPoolAccount = $null,
[Parameter(Mandatory=$true)]
[string]$AppPoolName = $null,
[Parameter(Mandatory=$true)]
[string]$DatabaseServer = $null,
[Parameter(Mandatory=$true)]
[string]$DatabaseName = $null
# check to ensure Microsoft.SharePoint.PowerShell is loaded if not using the SharePoint Management Shell
$snapin = Get-PSSnapin | Where-Object {$_.Name -eq 'Microsoft.SharePoint.Powershell'}
if ($snapin -eq $null) {
Write-Host "Loading SharePoint Powershell Snapin"
Add-PSSnapin "Microsoft.SharePoint.Powershell"
Write-Host "Successfully Sharepoint Powershell snapin Loaded"
Write-Host "Started executing Powershell script for configuring Business Data Connectivity Service in sharepoint farm ..."
Write-Host -ForegroundColor Yellow "Checking if Application Pool Accounts exists"
$AppPoolAccount = Get-SPManagedAccount -Identity $AppPoolAccount -EA 0
if($AppPoolAccount -eq $null)
Write-Host "Please supply the password for the Service Account..."
$AppPoolCred = Get-Credential $AppPoolAccount
$AppPoolAccount = New-SPManagedAccount -Credential $AppPoolCred -EA 0
Write-Host -ForegroundColor Yellow "Checking wether the Application Pool exists"
$AppPool = Get-SPServiceApplicationPool -Identity $AppPoolName -ErrorAction SilentlyContinue
if (!$AppPool)
Write-Host -ForegroundColor Green "Creating Application Pool"
$AppPool = New-SPServiceApplicationPool -Name $AppPoolName -Account $AppPoolAccount -Verbose
Write-Host -ForegroundColor Yellow "Checking if BDC Service Application exists"
$ServiceApplication = Get-SPServiceApplication -Name $ServiceName -ErrorAction SilentlyContinue
if (!$ServiceApplication)
Write-Host -ForegroundColor Green "Creating BDC Service Application"
$ServiceApplication = New-SPBusinessDataCatalogServiceApplication –ApplicationPool $AppPool –DatabaseName $DatabaseName –DatabaseServer $DatabaseServer –Name $ServiceName
Write-Host -ForegroundColor Yellow "Starting the BDC Service"
#$ServiceInstance = Get-SPServiceInstance | Where-Object { $_.TypeName -like "BDC Service*" }
#Start-SPServiceInstance $ServiceInstance
Get-SPServiceInstance | where-object {$_.DisplayName -eq $ServiceName} | Start-SPServiceInstance > $null
Write-Host -ForegroundColor Green "Done - BDC Service is up and running."
Error i am getting ->
Started executing Powershell script for configuring Business Data Connectivity S
ervice in sharepoint farm ...
Checking if Application Pool Accounts exists
Checking wether the Application Pool exists
Creating Application Pool
VERBOSE: Leaving BeginProcessing Method of New-SPServiceApplicationPool.
New-SPServiceApplicationPool : The trust relationship between the primary
domain and the trusted domain failed.
At C:\SP2013Service\BDC1.ps1:67 char:12
+ $AppPool = New-SPServiceApplicationPool -Name $AppPoolName -Account
$AppPoolAcco ...
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~
+ CategoryInfo : InvalidData: (Microsoft.Share...ApplicationPool:
SPCmdletNewIisWebServiceApplicationPool) [New-SPServiceApplicationPool], S
ystemException
+ FullyQualifiedErrorId : Microsoft.SharePoint.PowerShell.SPCmdletNewIisWe
bServiceApplicationPool
VERBOSE: Leaving ProcessRecord Method of New-SPServiceApplicationPool.
VERBOSE: Leaving EndProcessing Method of New-SPServiceApplicationPool.
Checking if BDC Service Application exists
Creating BDC Service Application
New-SPBusinessDataCatalogServiceApplication : Cannot bind argument to
parameter 'ApplicationPool' because it is null.
At C:\SP2013Service\BDC1.ps1:75 char:84
+ ... pplicationPool $AppPool –DatabaseName $DatabaseName –DatabaseServer
$DatabaseSer ...
+ ~~~~~~~~
+ CategoryInfo : InvalidData: (:) [New-SPBusinessD...viceApplicat
ion], ParameterBindingValidationException
+ FullyQualifiedErrorId : ParameterArgumentValidationErrorNullNotAllowed,M
icrosoft.SharePoint.BusinessData.SharedService.SPNewBusinessDataCatalogSer
viceApplicationhi guys,
same script i have modified with parametes,in below script i have hard corded values for parameters,and it is executing without errors.
Below is script executing without error->
Add-PsSnapin Microsoft.SharePoint.PowerShell -ErrorAction SilentlyContinue
#Settings
$ServiceName = "BDC Service"
$ServiceProxyName = "BDC Proxy"
$AppPoolAccount = "DOMAIN\USERNAME"
$AppPoolName = "BDC SP Ser App Pool"
$DatabaseServer = "SPSQL"
$DatabaseName = "SP2013 BDC"
Write-Host -ForegroundColor Yellow "Checking if Application Pool Accounts exists"
$AppPoolAccount = Get-SPManagedAccount -Identity $AppPoolAccount -EA 0
if($AppPoolAccount -eq $null)
Write-Host "Please supply the password for the Service Account..."
$AppPoolCred = Get-Credential $AppPoolAccount
$AppPoolAccount = New-SPManagedAccount -Credential $AppPoolCred -EA 0
Write-Host -ForegroundColor Yellow "Checking wether the Application Pool exists"
$AppPool = Get-SPServiceApplicationPool -Identity $AppPoolName -ErrorAction SilentlyContinue
if (!$AppPool)
Write-Host -ForegroundColor Green "Creating Application Pool"
$AppPool = New-SPServiceApplicationPool -Name $AppPoolName -Account $AppPoolAccount -Verbose
Write-Host -ForegroundColor Yellow "Checking if BDC Service Application exists"
$ServiceApplication = Get-SPServiceApplication -Name $ServiceName -ErrorAction SilentlyContinue
if (!$ServiceApplication)
Write-Host -ForegroundColor Green "Creating BDC Service Application"
$ServiceApplication = New-SPBusinessDataCatalogServiceApplication –ApplicationPool $AppPool –DatabaseName $DatabaseName –DatabaseServer $DatabaseServer –Name $ServiceName
Write-Host -ForegroundColor Yellow "Starting the BDC Service"
#$ServiceInstance = Get-SPServiceInstance | Where-Object { $_.TypeName -like "BDC Service*" }
#Start-SPServiceInstance $ServiceInstance
Get-SPServiceInstance | where-object {$_.DisplayName -eq $ServiceName} | Start-SPServiceInstance > $null
Write-Host -ForegroundColor Green "Done - BDC Service is up and running."
if any body want need more information please can u respond me to
Email id:[email protected]
Maybe you are looking for
-
Hi All, After the upgrade of MII from 12.1 to 14, I am unable to see the animated object. It displays nothing on click of the 3D Dial guage object in the Default folder of workbench. All other objects like Alerter,LED meter etc are displaying, excep
-
I can't connect to the itunes store. I've tried everything in the articles for trouble shooting and nothing works. My library comes up, my ipod syncs, and I get no alert messages. I'm running Vista.
-
MacBook Pro 2.0 Upgrades
I use my MBP to run Aperture and will soon be running Logic as well. I am constantly battling hard drive space (I can't even install Logic right now). I currently have a 100gb drive. I want to upgrade. I know I need a SATA drive, and I would like a 7
-
IMAQ Write JPEG File doesn't save color
Hi, I'm writing an 8 bit image to file. If I save it as bmp (using "IMAQ Write BMP.vi") File then color data is saved. If I save it as Jpeg using "IMAQ Write JPEG File", then I only get grayscale. I have attached a demonstration. There appears to be
-
Problem loading Image data with French accent in file name
We have a very complex commercial application that has been working perfectly in English for over a year. We have now localized it to French and Spanish, and discovered a serious show-stopping problem. We need help fast, with the scheduled release be