Not Able to Connect to Intranet Web Server

We have ASA5550 (ver. 8.0.4). We setup Split-tunneling. The Remote users were NOT able to access the intranet web server using Cisco VPN client. However, they were able to access other internal resources. We were able to ping the IP address of the Intranet Web server, but we were NOT able to ping by name. Do you have any suggestions?
Thanks.

Thanks for your response and information. The VPN adapter shows the Corporate office's DNS server. When I typed NSLOOKUP, the Remote computer also showed the Corporate office's DNS server. So, does it mean the DNS is setup correctly on the ASA?
We have about 100 Remote offices, do we need to put in 100 DNS servers for Split-DNS? The Remote offices are using Cisco VPN client to connect to us.
Thanks.

Similar Messages

The Blackbery device simulator is not able to connect to the mobile server.

Hi
While login to Sap Mobile BI i get the below error.
"unable to connect to mobile server.The request is timed out(0x008)"

Thank You for your reply.I had no problem with the mobile network connections it is on.The issue i am facing i am using proxy server deployment where we don't have to mention host_port in the vas cluster configuration due to which i m not able to connect to blackberry Simulator which is on client machine.But if i specify the client machine port to Host_port then i m able to connect.Can you help me to configure the Mobile server for a non-BlackBerry
deployment that uses a proxy server

Clients not able to connect to MS exchange server over a cisco switch

Hello,
I have a Cisco L3 switch.
I have a Exchange server and until i split the network into every thing was working ok, meaning the clients can connect to the Exchange without issues.
But after i split the network into 2 vlans, moving the exchange in one vlan and the clients in another vlan, i have complains saying that the users are not able to connect to exchange periodically.
Even users from the same subnet also cannot connect to the exchange often.
Meaning the clients can connect to the exchange and suddenly it will stop working. at the same time i can ping the exchange and that shows there is no routing issue or LAN issue.
But still clients cant connect to the exchange, when i reboot it will start working again for some time.
wondering whether it could be related to any network related issue or MTU or PMTUD issues.
The whole issue started only after we split the network into two vlans.

If you have physical access to the switch, it may save time to look at the port LEDs which give you the link status or may indicate an error condition (if red or orange). The table below describes the LED status indicators for Ethernet modules or fixed-configuration switches:
http://www.cisco.com/en/US/customer/products/hw/switches/ps700/products_tech_note09186a008015bfd6.shtml

Oracle FileSync: not able to find the Oracle Web Server

Hi,
I am having the OCS 10.1.2.3.0 on a Linux server. I am not able to create a mapping in the Oracle FileSync
While Adding a mapping in the Web Server mapping wizard
the http://<server>:<port>/<DAVRoot> i have given as per my server settings as http://server.domain.com:7778/content/dav
but it is showing the error as
The URL you have entered is not a valid Oracle web server
Is this because of the Web Listener is not running in the server.. How to clarify this..?
Thanks,
Prasant
Message was edited by:
prasant

Hi Arnaud,
Yes , Oracle FileSync is a separate tool that can be used to Map folders in the web server and synchronize the files
The issue is when i was trying to create a mapping, it ask for the Web Server URL for the first time
its format is http://<webserver>:<port>/<DAVROOT>
when I tried with my OCS server : server.domain.com
Port: 7778
DAVROOT: cmsdk/content or content/dav
its showing that the WebServer you entered in the URL is not a valid Web Server
NB: **** I am facing the same issue with the Oracle Messenger also..
-- How can i verify that the Oracle Web Server is up in Linux and the Web Port that is listening..?
Please update...
Many Thanks,
Prasant

Not able to connect to Oracle 10G server

Hi All
I have installed Oracle Clinet 10G and i am able to connect to oracle server using sql plus, but not through Microsoft OLEDB data provider for Oracle.
Error : Test Connection Failed because of an error initializing provider, oracle error occured,
but error message could not be reterived from Oracle.
also before installing Oracle clinet i have SQL Server 2005 and 2008 client in my system.
How can i connect with oracle server using Microsoft OLEDB data provider for Oracle.
How would i know what excatly is the issue?

887065 wrote:
Hi All
I have installed Oracle Clinet 10G and i am able to connect to oracle server using sql plus, but not through Microsoft OLEDB data provider for Oracle.
Error : Test Connection Failed because of an error initializing provider, oracle error occured,
but error message could not be reterived from Oracle.
also before installing Oracle clinet i have SQL Server 2005 and 2008 client in my system.
How can i connect with oracle server using Microsoft OLEDB data provider for Oracle.
How would i know what excatly is the issue?does listener.log file record connection request got that far?
consider using WireShark or Ethereal to packect sniff the data exchange between MS client & Oracle listener/DB

Mac not able to connect to SMB File Server

I'm having an issue with a Mac trying to connect to our file server. It was working before our company move but once we moved into our new building it stopped working. Our network settings stayed exactly the same except our router and firewall. It seems to me like it's a DNS issue because I am able to ping the server with the IP but when using the hostname is where it fails and also trys to ping an incorrect address. Our network is 192.168.X.X and it's trying to ping 69.60.X.X which seems like a outside address. I am able to ping the DNS server and seems to connect to computers with in the network but just not our File Server.

Hello:
You will need to delete the keyboard from the other Mac. Simply disconnecting it leaves it still paired with the first Mac.
Barry

Not able to connect to Lotus Domino server using java/corba

Hi
I am new to Lotus Domino server and Java.
I have INstalled Lotus Domino server5 on 1 machine and was successful in installing the Lotus client on another machine.
Throught the lotus client i am able to connect to the server and send and receive the mails.
Now I want to connect to the domino server using the Lotus Domino Tolkit for Java/Corba.
In this Toolkit they have given the sample code program ..
if I run the code I am getting the error
java.io.FileNotFoundException: http://<IPADDRESS>/diiop_ior.txtjava.io.FileNotFoundException: http://<IPADDRESS>/diiop_ior.txt
at sun.net.www.protocol.http.HttpURLConnection.getInputStream(HttpURLCon
nection.java:691)
at java.net.URL.openStream(URL.java:942)
at lotus.domino.NotesFactory.getIOR(NotesFactory.java:314)
at lotus.domino.NotesFactory.createSession(NotesFactory.java:66)
at IntroCorbaApp.run(IntroCorbaApp.java:65)
at java.lang.Thread.run(Thread.java:539)
lotus.domino.NotesException: Could not get IOR from HTTP Server
lotus.domino.NotesException
at lotus.domino.NotesFactory.getIOR(NotesFactory.java:344)
at lotus.domino.NotesFactory.createSession(NotesFactory.java:66)
at IntroCorbaApp.run(IntroCorbaApp.java:65)
at java.lang.Thread.run(Thread.java:539)
I also tried to find this file in the Domino server directory.
The file exists in drive:\LotusServer\Domino\Data\Domino\HTML directory..
I am not getting what exactly is the Problem
Plz any one help me in this regard..
thanks in advance

You should be able to access the diiop_ior.txt file from browser without authentication,only then it will work. This file should not
be protected.

Not able to connect P6 v7 Web access

Hi,
We have P6 Web Access installed at our company. Suddenly it has started showing the following Error when we try to connect it.
"504 Gateway Timeout: remote server did not respond to the proxy"..
Can anyone provide me the solution for this error.
Thanks in Advance

Hello Nesh,
the 504 Gateway Timeout indicates a problem in the network. Depending on your companys infrastructure I would suggest to access the WebAccess Server directly without the proxy. So you can test if it's available. You should mind to use a direct connection with the webaccess Server without a proxy.
Regards
Daniel

Apple TV not able to connect to the Apple Server

Not able to restore the Apple TV to factory settings....it says "unable to connect to the apple server". What should I do?

I too did what was recommended and still keep getting the "AppleTV cannot connect to the server at this time' message. If anyone has a solution to this issue...please advise

Mac computers in the office are not able to connect to our exchange server.

We started facing this problem about a month ago in our office where the apple computers can not connect to the exchange server via outlook or applemail or anything for that matter. All the other computers can connect to the exchange server with no problems
and the apple computers can even access the exchange server via OWA but the outlook and applemail apps would not connect to exchange. We have tried even deleting and re-creating some accounts on the apps but they still would not connect. At this point I am
at a complete loss and I looked everywhere through google to find out if anyone else has faced this problem but to no avail.
A little background information. This specific problem started happening after there was an un-expected series of power outages to the servers and they were shut down un-expectedly. I personally restored the servers and turned on all the services and made
sure everything was up and running after the power outages and everything was working fine. Also the first instance of the problem with the mac computers only happened two days after the servers were back up and running again and they had no issues in those
two days.
Right now we do not have that many mac users in our offices (only 3-4 users) and I have instructed them to use the OWA in the meanwhile but it is however an inconvenience to them. By now you may have realized that I am not a very experienced server admin
and I would really really appreciate any help. I extend my thanks in advance for any insight.

Hi Martin,
Thanks for the reply.
Right now I have Apple mail and Outlook installed on my mac laptop and both the applications do not connect to the exchange server. Apple Mail simply does a long process when I give my credentials to create my account and then it gives an error saying it
could not find the server while outlook quickly tells me that either the username or password is incorrect. At the same time I can connect to the server through outlook on my windows computer without any problems whatsoever.
From your reply, I gather that the VIA headers only affect Apple mail and should not affect Outlook app on the mac but right now, neither apps are connecting to the exchange server.
Either way I am trying to find out how to remove the VIA headers because it does not seem that we are using Kemp on the exchange server. Right now I do not have the in depth knowledge that I need because I was not involved in the implementation of our server
system, that was taken care of by a service provider and I was put in charge of mostly simple admin work. Now we are out of contract with the service provider so pretty much everything has fallen onto my shoulders.
If possible, would you mind pointing me in the right direction to finding out if I am using a L7 load balancer and how I would go about removing the VIA headers?

Not able to connect to the web

Hello,
just joined that forum because I have a problem which occurred not more than an hour ago and has been driving me crazy!.
I'm no longer able to connect to the internet. I've been using at home my WI-Fi and now I still am connected to the network, but not getting any signal from the router or should I say the Blackberry is not able to receive the signal..Every other device is working just fine on this very same connection. Tried to erase the network, took the battery off, have been switching on and off the Wi-Fi on the BB, but to no effect...
Thanks

my internet and averything else was fine up until today . i have been on wi-fi connected to my wireless broadband at home and its still doing the same,very slow and not letting me download anything.if it was blackberry surely it wouldnt let you on the internet.could it be that my memory onmy phone is full even though i have a media card in it.open to all suggestions.

I am not able to connect to the apps server

I get an error code 1 when I attempt to log into the apps section from my printer. I talked to tech support and we checked everything. All is good except for getting into the apps section.

Hi jbsytes,
What printer are you trying to access the print apps with?
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Not able to connect to SMTP server

Hi all,
I am new to java mail.
I tried to send an email from my official account,gmail account,yahoo account.
i get an exception as Exception reading response; and Connection reset
when i enabled debug as true
it says trying to connect to host "smtp.gmail.com", port 25, isSSL false
i am not able to figure out why iam not able to connect to the smtp server.
also i tried with authentication as true and false.
your timely reply is appreciated.
Thanks

Have a look at this thread:
http://webcache.googleusercontent.com/search?q=cache:SRl7qfZ3biQJ:forums.sun.com/thread.jspa%3FthreadID%3D5196042+site:forums.sun.com+smtp+java+%22exception+reading+response%22&cd=3&hl=en&ct=clnk&gl=uk&client=firefox-a
(not sure where it has been migrated to so using cache..)
Note: smtp.gmail.com requires TLS or SSL

Not able to connect to java server

Hi,
I am not able to connect to the java server (for example server startpage) but i can open this page from the same system in which it is installed and not from other system.
Could anyone help me out?
Regards,
Pradeep KS

Please open the hosts file in your machine (Start>Runtype drivers-->etc) and enter the following line
<IP address of server > <hostname>
save the file.
Then try to open the URL for accessing the server.

Not able to connect pws prime cable provisioning

Dear all.,
We are not able to connect the provisioning web service of prime cable provisoning . We installed prime cable provisioning all in default.
We can't find the correct port aaddress for example we installed in centos machine IP is 10.2.0.151 port is 9100 . we are using the same IP but not able to connect in visualstudio .

Finally we find out the provisioning web service
this.Url =
http://localhost:9090/ProvisioningPort This URL is wrong one
http://10.2.0.151:9100/cp-ws-prov/provService?wsdl This one is the correct

Not Able to Connect to Intranet Web Server

Similar Messages

Maybe you are looking for