Not able to see devices in fault monitor LMS 4.0

I can see devices in the managed group ,but cannot see devices in fault monitor,its show no device available

Balbir,
LMS 4.0 is now obsolete. We recommend to use LMS 4.2.x to have the support.
In LMS 4.x the devices are by default managed by each module like fault monitor. Please share a screenshot where you're expecting and don't see devices.
When was this installed? Was it working ever? You can also try to reset your fault Monitor module by reinitializing the DataBase for Fault.
Check the commands from here:
LMS Database Troubleshooting
-Thanks
Vinod
**Encourage Contributors. RATE Them.**

Similar Messages

LMS 3.2 Not able to see devices in cs device management

Not able to see devices in CS device management (0 devices).but devices are visible in other modules like RME and DFM.
can anybody help..
Thanks in advance...
Regards,
Channa

Thanks for reply Afroj..
The issue is resolved.deleted those devices and readded it worked..
But am hitting with another issue am not able to add devices into DCR.after the finish device addition status summary
not shown.device also not shown in DCR.
Kindly suggest..
Thanks,
Regards,
Channa

When I go to create a new project in imovie using the iPhone 5, I am not able to see any of my video clips or photos that are saved on the device.

When I go to create a new project in imovie using the iPhone 5, I am not able to see any of my video clips or photos that are saved on the device.

When you move or copy the compound clips with their events into an external drive all the events should be there. Not clear on why you want to move them into a single event. You can drag and drop from one event to another.
Why are you using compound clips? You can simply copy the project from each machine with used media onto the external drive and that should do it.

Cisco 877w - Apple devices not able to see wired apple TV

Hello All,
Can anyone point me to a doc or forum discussion on how to setup the wireless interface to forward multicast packets? Basically I cant get the ipads etc.. to see the AppleTV to control it. I connected an AP and it works fine so its got to be something with the way the router handles the packets from teh integrated wireless interface. I've been searching the forum for about 1hr and haven't founf anything other than a breif mention of broadcast forwarding and multicast setup.
Has anyone got anything more complrehensive I can read?
Thanks
David

Hello David,
Thank you for contacting the Sales Acceleration Center (SAC) regarding your recent inquiry, Case Number
Case Description:
Cisco 877w - Apple devices not able to see wired apple TV
Case Solution:
The Bonjour service uses multicast to advertise your Home Sharing enabled device to the local network. In my case the Cisco 877W I was using had a Layer 3 enabled BVI (Bridged Virtual Interface) to which the Wireless Dot11Radio interface was not fowarding multicast packets properly.
First of all, obtain the Multicast groups your wireless adapter is configured for (on Windows open a command prompt and run the below command):
The result will give you an output as per below, we are interested in the multicast address directly after the 224.0.0.252 address 239.255.255.250:
Then we need to enable multicast routing on the router, connect to your router and enter config terminal mode:
Next we will configure IGMP v3 and add the relevant Wireless interface on your router to the correct multicast address group:
Next perform the same config your BVI interface:
Once complete save your changes and confirm both interfaces have been added to the multicast groups using the command sh ip igmp group:
You now need to reload your router and restart iTunes and then attempt to connect to Home Sharing from your Apple TV.
Other commands that I used to troubleshoot with were:
debug ip mpacket - Multicast Packet Debugging
debug ip mroute - Debug Multicast Routing
sh ip mroute - Show IP Multicast Routes
By default the Cisco implementation of a Dot11Radio interface and a BVI interface don't appear to forward multicast packets between each other. Seems odd to me as they're both in the same L2 bridging group..anyway.
I am going to close the case for this specific inquiry on my side. If you need moere information Please feel free to reach out to me or any member of the SAC team if we can be of any further assistance or if you have any other related questions in the future. We strive to provide you with excellent service. We value your input and look forward to serving you moving forward.

File Monitoring - Not able to see File Path on the Detail Information Tab

Hi Experts:
I am setting up the "File Monitoring" in the Solution Manager. I am having STA/PI01L_CRM570 on the Solution Manager.
And on the Satelite System - ECC I have STA/PI 01L_ECC600
While I am setting up the parameters, I am supposed to provide the file path in "Detail Information" tab page.
But I am just able to see two tabs:
Count and Short Text (optional).
I checked all the other tab but not able to locate where I need to provide the file path.
Can any one let me know, If I am missing anything or do I need to do any further steps.
Similarly for the File Size setting:
I am not able to see where I can define The parameter "File Pattern (e.g. *.log, *.txt or any string)" is mandatory.
Pls let me know.
Regards
John

Hello Johns,
You can find the FilePath in the 'Detail Information' tab if you double click the initial and predefined counter 001.
Best regards,
Goncalo Mouro Vaz

I am trying to communicate with third party instrument via usb but I dont know how to do it even in Ni-max I am not able to see usb port symbol in Devices and Interface section.

hello,
I am tring to communicate my Powersupply which is not from Ni via USB cable ,but I am not able to see my connection or usb symbole in Ni-max .
first time I am using this will you please guide me,and is there any driver i need to download for that?here I put one attachment regarding to this.
Thanks in advance.
Solved!
Go to Solution.
Attachments:
usb is not detected.png ‏182 KB

ya I know that,
thats y i asked you that y it is so because i am not able to see that usb port here i can see that much only.
thats y i got confused.
and I can see my hameg connection in my control panel and also in device manager.
http://www.hameg.com/drivers.0.html?&no_cache=1
this is website for hameg driver in that product select hmp4040 than hmp4000 list will open in that i have download third one in which plug and play is given.
or here i send my vi it might be helpful.
Attachments:
hmp4040 Output DC Volts.vi ‏17 KB

I am not able to see manage devices option on my account summary ? Please help

I am not able to see manage my account option on my account summary . I need to associate more apple devices to my account . Please help on this issue ..
Regards

Thanx kbrosnan. Enter key will work if my keyboard is Google Keyboard but if i have another keyboard type (C-DAC, GIST Marathi Keyboard) then if I press enter key it will take special invisible character may be carriage return and not getting expected action. Using same C-DAC keyboard I am able to get expected action in another application. So is that browser problem of keyboard problem?
Ref C-DAC Keyboard: http://cdac.in/english/down/gist/android_soft_keyboard_marathi.aspx

Apple TV and iTunes not able to see each other

I think I have found a bug in either iTunes or Apple TV. My network configuration is a bit complicated so I will describe it first.
Cable modem into my house hitting a Linksys WRT330N router at a central box in my laundry room. From there my house is hard wired to different rooms of the house. One goes to my office where I have a Apple Extreme N airport, connected to my PowerMac and my iTunes library. Again out of the central point in the laundry room again hard wired I have a wire going to my living room, where I have another Apple Extreme N airport, this is where my Apple TV is hard wired too. I have all the latest firmware and software installed on all my devices. Also both Airport Extreme's are setup using bridge mode and letting the Linksys serve the IP addresses for my network.
Now to the problem. I can not explain when or why but my Apple TV and iTunes are not able to see each other after about 48 hours. I have tried all kinds of troubleshooting steps including changing my connection from being hard wired to wireless connecting directly to the Airport Extreme my iTunes computer is connected too. I know my network connection is good as I can see trailers and pull up video's from uTube.
The only way to get them to see each other again is to do a factory reset of my Apple TV. After I do this they can both see each other again. But again after about 48 hours they lose the ability to see each other. I have taken these steps twice now to fix the problem
I just finished reseting my Apple TV and am going to watch it to see when it stops working the next time.
All of these problems started the other day when I introduced a new Apple Extreme N router in my my network. The airport Extreme seem to be working fine with my PS3 and XBox 360 that is also connected to it. So I don't think it's the router that is causing the problem.
If I had to guess I would say something in the Apple TV is locking up. Although I have tried power cycling the Apple TV which does not fix the problem. I'm going through 3 routers to get between the Apple TV and the iTunes library somehow it appears the Apple TV is losing it way.
I welcome any help as I don't want to have to keep factory resetting my Apple TV to keep it working.

Fascinating just reading about your setup. I have a WRT350N and have noticed that it will drop its speed, sometimes down to 1Mbps. It seems to do so at about the same time every day, but usually comes back to speed in about 5 minutes. In my experience, the Apple TV will disconnect if the speed falls this low. Try monitoring the Linksys with Netstumbler, Vistumbler, or just in the Windows Network utility.
Check the "lease obtained" and "lease expired" times for your router to see if that is when the network fails. I've just finished reading an angry thread over at the Linksys forum about the WRT330N where someone mentioned that the router wasn't renewing its lease.
"I cannot set it run off automatic DHCP from the WRT330N, the router will not assign it an IP every time the lease expires, causing me to have to manually set an IP on the Print server. That's annoying. Having the router drop IP's to individual machines after 12-48 hours...very annoying."
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread .id=67412
If that is the problem, then I would consider setting up a Static IP address for your Apple TV. You can do that through the user interface -> Settings -> Network -> Configure ... (Quite intuitive as you only have change IP address and the subsequent details remain the same.)
My router assigns IP Addresses in the ranges of 192.168.1.100 ->149. The idea here is to choose an address outside of that range but is not greater than 192.168.1.253 (and should not end in the number 1). You shouldn't have to change the linksys router as long as 50 clients are assigned in that range. You'll have to figure that out by accessing your router webpage at browser address 192.168.1.1 -> the default password is "admin" (without the quotes).
Good luck.

Not able to see the records in master data

Hi friends
My requirement needs the data to be loaded from a RDM table.I created a data source in the R/3 and by using the extracto checker i am able to see the data.I created the info packages one for Attr and other Txt,replicated the datasource and loaded the data.I am able to see the data in the PSA and when i go into monitor in the infopackage it says the data has been loaded and it shows no errors.But I am not able to see this data in the master data info object.Can anyone please help me out???
Mouli

Hi
Check out your infopackage setting: if its upto PSA or to MD table also
Open Master data table in SE11 and check the OBJVERS field wether the MD is activated or not!
Regards
GSK

ODBC connection not able to see all schemas

Hi everyone,
We have noticed an unusual problem that just recently started. In our database, I have created a read-only user - only has the ability to connect to the database, and SELECT ANY TABLE. Then we have some applications (Crystal Reports and Lotus Notes Agents) that use this user to query data. The applications use an ODBC connection, and when we initially set this up, everything worked beautifully.
However, suddenly we have noticed that the ODBC connection is not able to see all of the schemas in the database. We have tested and confirmed this - using either 9.02 ODBC or 10.01, this happens with both of them. I created a couple new ODBC connections, one for each version, then I try to create a new Crystal Report, using this ODBC connection - when I connect using the read-only user, it connects just fine, but when it shows me all of the schemas available, I am only seeing about half of them (and of course not seeing the one that I really need to see).
However, when I use Microsoft Access, and try to import some External Data, and I use the same ODBC connections, then I AM seeing all of the schemas.
Has anyone ever seen anything like this? Any ideas on what I can do to troubleshoot?
Thanks,
Brad

I'm trying to get this issue figured out. Can you
tell me what you mean when you ask me to log in
directly as the same user using ODBC and query
ALL_TABLES - how would I do that?Using whatever Oracle database account you use in Crystal, log in to the database using SQL*Plus (or your favorite GUI like SQL Developer) and run a query like
SELECT owner, table_name
FROM all_tablesDoes that query show all the tables you expect, or are you missing some?
Also, you mention a parameter in the ODBC API that
controls which schemas are returned - is there any
way to see that value?An ODBC trace might show the value, I don't recall if the actual value is written out in the trace. Different front-end tools often have a place that allows you to filter out certain schemas, which is generally done by passing in a parameter to this ODBC API call. I don't know enough about your tools, though, to know where this might be.
Are there any other ODBC drivers I could try?There are plenty of third party ODBC drivers out there, but I would tend to be suprised if the ODBC driver was at fault here. You could also try patching the ODBC driver and/or Oracle client to the most recent patchsets.
Justin

I am not able to see images in Facebook while i am connecting throw wifi

I am not able to see images in Facebook while i am connecting throw wifi

Hello amitkcindia,
I would recommend verifying your WiFi router's settings against our recommendations for use with iOS and Mac OS devices.
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/HT4199
Cheers,
Allen

Complaint - Structured Product - Not able to see the componentitem details.

Hi.
First Question:
I have a Structured Product (For eg. a Structured Producted is called Desktop Computer. It has two items say Monitor, Mouse.) In my complaint transaction, when I add this product, I dont see the components within it which are associated in the SAP GUI.
Note: In the Item Category determination for the header product, I have chosen the option 'Single Level explosion of structured products'.
But still I am not able to see the items when I add this Structured product to the complaint transaction. Can anybody throw any light as to what could be missing ?
Second Question:
Will the component items be visible in the ICSS. I am only seeing the product header but not seeing the items within it. What could be mising here ?

Hi,
For marketing there is a standard Busines rolle MARKETINGPRO with
PFCG Rolle SAP_CRM_UIU_MKT_PROFESSIONAL. Please check whether it is also valid for
Utilities.
I dont see any Marketing workcenters and Links in the "SAP_CRM_UIU_UTIL_IC_LEAN_AGENT" Rolles.
Regards,
Usman

After registering SAPCCMSR agent not able to see J2ee nodes in rz20

Hi,
After registering SAPCCMSR agent on J2ee instance not able to see J2ee nodes in rz20. The ccms_connetor file has the
following error
Feb 26, 2012 8:43:44 AM ...y.monitor.mapping.ccms.Selfmonitoring [SAPEngine_System_Thread[impl:5]_65] Error: Couldn't create self monitoring (java.lang.RuntimeException: Update on node failed (java.lang.IllegalArgumentException: Method
name is empty.)).
Feb 26, 2012 8:43:44 AM ...ne.library.monitor.mapping.ccms.Trace [SAPEngine_System_Thread[impl:5]_65] Error: Could not read host name (com.sap.mona.api.JMonException: No instance info available.)
Feb 26, 2012 8:43:44 AM ...ne.library.monitor.mapping.ccms.Trace [SAPEngine_System_Thread[impl:5]_65] Error: RegisterNode</>: com.sap.mona.api.JMonException: java.lang.RuntimeException: Update on node failed (java.lang.IllegalArgumentEx
ception: Method name is empty.)
Feb 26, 2012 8:43:44 AM ...ne.library.monitor.mapping.ccms.Trace [SAPEngine_System_Thread[impl:5]_65] Error: Could not read host name (com.sap.mona.api.JMonException: No instance info available.)
Feb 26, 2012 8:43:44 AM ...ne.library.monitor.mapping.ccms.Trace [SAPEngine_System_Thread[impl:5]_65] Error: RegisterNode</>: com.sap.mona.api.JMonException: java.lang.RuntimeException: Update on node failed (java.lang.IllegalArgumentEx
ception: Method name is empty.)
Feb 26, 2012 8:43:44 AM ...ne.library.monitor.mapping.ccms.Trace [SAPEngine_System_Thread[impl:5]_65] Error: RegisterNode</Kernel>: com.sap.engine.library.monitor.mapping.ccms.CcmsConnectorException: /Kernel can't be created due to missing parent node(s).
Feb 26, 2012 8:43:44 AM ...ne.library.monitor.mapping.ccms.Trace [SAPEngine_System_Thread[impl:5]_65] Error: Could not read host name (com.sap.mona.api.JMonException: No instance info available.)
Feb 26, 2012 8:43:44 AM ...ne.library.monitor.mapping.ccms.Trace [SAPEngine_System_Thread[impl:5]_65] Error: RegisterNode</>: com.sap.mona.api.JMonException: java.lang.RuntimeException: Update on node failed (java.lang.IllegalArgumentException: Method name is empty.)
Feb 26, 2012 8:43:44 AM ...ne.library.monitor.mapping.ccms.Trace [SAPEngine_System_Thread[impl:5]_65] Error: RegisterNode</Services>: com.sap.engine.library.monitor.mapping.ccms.CcmsConnectorException: /Services can't be created due to missing parent node(s).
Can some one help me on this.
Thanks

Hello Kranthi,
I would suggest you to cross check the steps you have performed to register sapccmsr agent with the following help links and update us.
http://help.sap.com/saphelp_nw04/helpdata/en/48/6a76607a7c91409474ad6c7b6f5a26/content.htm
Good Luck.
Thanks,
Siva Kumar

Not able to see that particular query which is executed from application

Hi Friends,
I have one application which is executing a number of queries in the current session. I want to know which query is taking how much time?
So I have executed following query in Toad for this purpose, but this is giving details of those queries only which are executed from either Toad or SQL developer.
I am not able to see that particular query which is executed from application. Please suggest me if I am missing something.
select ss.schemaname,ss.machine,ss.program,ss.logon_time,ss.sql_exec_start,ss.wait_time,
sa.first_load_time,sa.application_wait_time,sa.plsql_exec_time,sa.cpu_time,sa.elapsed_time,sa.sql_fulltext
from v$session ss, v$sqlarea sa
where sa.hash_value=ss.sql_hash_value
order by sa.first_load_time desc;
Oracle Version - Release 11.2.0.1.0 Production
Toad Version - 9.5.0.31
Regards,
Sachin

Dear Friends,
is there any option for this through Oracle Enterprise Manager 11g?
Actually I have done little bit research on EM console and go through SQL Monitoring Executions page but did not get the particular query details executed through the application.
I have also checked the link - AWR Baseline but not get any result.
As I am new in database administration activities, Please help me regarding this. You can also suggest me other solution except Oracle EM console.
Thanks.
Sachin Jaiswal

I am not able to see proper website?

I am not able to see my blog properly in Mozilla Firefox for Android phone. My personal blog URL is http://www.pagalblogger.in

Its viewing perfectly in Samsung S2 -JB
Many site issues can be caused by corrupt cookies or cache. In order to try to fix these problems, the first step is to clear both cookies and the cache.
The Firefox cache temporarily stores images, scripts, and other parts of websites while you are browsing. 
Note: ''This will temporarily log you out of all sites you're logged in to.''
To clear cache and cookies, do the following:
#Tap the menu icon located at the top right corner. This is the icon with 3 bars. On older Android devices you'll have to press the hardware menu key and then tap More.
#Tap '''Settings'''.
#After that, you will be taken to the settings screen. In the settings screen, look under the section '''''Privacy & Security''''' and select '''Clear private data'''.
#You will then be taken to a list of what can be cleared. Select the following 2 for deletion:
#*Cookies & active logins
#*Cache
#After those have been selected, tap the '''Clear data''' button to actually clear the cache and cookies.
Did this help you with your problems? Please let us know!

Not able to see devices in fault monitor LMS 4.0

Similar Messages

Maybe you are looking for