Not able to start 'INTEGRATION REPOSITORY' but able to start 'DIRECTORY'.

Hi Gurus,
In the XI Infrastructure tools --->
i am able to start 'integration directory ' and able to logon.
But not able to start 'integration repository' , i end up getting the message'
Unable to start integration builder ' with details 'Failed to load resource'.
I have seen all the blogs related to this issue , but have not come across this
scenario where one works and other does not.
this error message is shown in details
unable to load resource :http ://XXXX:50000/rep/rep/repository/aii_proxy_gen.jar
please help me.
Message was edited by:
khan voyalpad usman

Hi,
It seems that jar files for IR has not been imported into your local machine and that is the reason it is not opening. What happens when you click on IR is, it just connect to your server and imports the neccessary jar files to your local machine but some time if system is very busy then the connection breaks, so in this case you may have to click many times on IR so that all jar fils will be imported on your local machine. The percentage of jar files imported will be displayed at the time of import and at the same time if conncetion goes down then next time it starts from the point where it got disconnected (not from the starting). I guess this is the problem.
Regards,
Sarvesh

Similar Messages

Problem in starting Integration Repository

Contrary to another thread that I found, I am having problems starting Integration Repository for the first time after installation. I followed the instructions of the installation guide up to the point of running SXMB_IFR to launch SAP Exchange Infrastructure page, and after clicking on "Repository (Design)" link, the java web start first check for the latest version, then it goes berserk trying to start the application (the progress meter flashes) and ~2 hours have passed as I am writing this. The documentation warns of a long starting time but this?? Appreciate it if any fellow friends have encountered this before and leave your comments...
Another thing: "Directory (Configuration)" link works without a glitch, comes up in 2-3 minutes and I am able to log in. Weird...

Hi!
> I am having problems starting Integration Repository
> for the first time after installation.
We also have a similar problem on clients launching the Integration Repository for the first time. The error message is:
An error occurred while launching/running the application.
Title: Integration Builder
Vendor: SAP AG
Category: Download Error
Corrupted JAR file at http://<host>:50000/rep/repository/aii_ibrep_client.jar
When trying several times it suddenly works without having changed any settings. But on some clients it does not work at all and there is always the error message mentioned above.
The proxy settings are correct on all clients. aii_ibrep_client.jar is not corrupted as I can download and unzip it without any problems.
Does anybody know how to avoid this error? Thanks for your help.
Regards, Tanja

Error while starting Integration Repository and Integration Directory

Hi Friends,
When I am trying to start Integration repository,it giving me error 'Unable to load resource: http://SPCC-SAPPIDEV:50000/rep/repository/iaik_jsse.jar'
How to solve this? please gve ur suggestions.
Thanks & Regards,
Brijesh Soni

Hi Suman,
I am able to solve that problem now.
1) From the main screen of XI go to Administration.
2) From left side Under Repository tab click on Javau2122 Web Start Administration ,which is under Javau2122 Web Start.
3)On the main window there on 3 options, from that select Re-initialization . it will gve some msg and then log off from this.
4) Now close this window, and again restart the main window , and now click on IR . It will reinitillize and will start working,
5) if ID also have same problem, repeate the same thing jst in step 2) select Directory tab and rest of process same as above.
Brij...

How to create abapProxy in nw 7.01 not 7.1 from integration repository

i use nw 7.01 , it's sproxy inteface is different old and new ones like 7.1 so i couldnt create abap proxy in sproxy.I created an message interface in integration repository but i couldnt find any object releated to this in sproxy..
I found some documentation about 7.1 , it mentions that you must create a service interface in IR but in my version it doesnt exist.
so how to create or copy existing proxy class?
Thanks alot

I guess it should be similar to PI 7.0 environment wherein you have to create message interface in IR. Then use SPROXY transaction at R3 (not XI). From there you may select the interface and create proxy. For this make sure that abap proxy is activated at your R3 system.
Regards,
Prateek

HT201276 hi I was unable to quit Safari on my laptop it is buffering but it is not closing i have re-started the laptop but after re-start the laptop safari is not closing still it is buffering

hi I was unable to quit Safari on my laptop it is buffering but it is not closing i have re-started the laptop but after re-start the laptop safari is not closing still it is buffering
Please help me

Force Quit Safari.
Press command + option + esc keys together at the same time.
Wait.
When Force Quit window appears, select Safari if not already.
Press Force Quit button at the bottom of the window.
Wait.
Safari will quit.
If this does not help, press the power button for 7 or more seconds.
Computer will shut down.
Restart.

G5 Starts Up Fine But Doesn't Start Monitor Consistently! I'm stumped!

Hello all. I just purchased a new Mac Pro. My G5 has been problematic for a number of months now even under Leopard. I replaced the internal battery, have done PMU and zapped PRAM and nothing solved my problem. The problem has been: It takes me at least 2 pushes of the power button but sometimes 3 or more to get video on my 20" Cinema Display. This only happens at the start of the day.
Upon receiving the Mac Pro, I zeroed out the G5 hard drive in preparation for sale on eBay but I wanted to make sure that it would start consistently for the new owner. That is the only problem I've ever had with the G5. I then installed Tiger and all the associated upgrades but zero additional software.
I connected to a Samsung monitor with its own cable. I was gone for the weekend, came home and G5 and monitor started up beautifully first time. Great, I thought. This morning, three fresh starts off the G5 power button started everything up just fine but the monitor did not come on. The computer boots up but the monitor does not come on. After one PRAM zap, up it came just fine. I reseated the two 512MB RAM sticks, pressed the PMU button once and and hoping for better things but I can't figure this out as the computer otherwise runs fine. I thought it might have been a pesky .KEXT file or something but a zeroing of the hard drive and installation of Tiger should have fixed that, true?
Anyway, I want to make sure the new owner will have a trouble-free computer.
Any suggestions on how I might fix this problem, and, indeed what the problem might be? It appears that the monitor cables and the two monitors are fine as they work fine with other computers. I always thought this was some sort of third party issue but with the newly installed Tiger and updates that's eliminated. Might it be a problem with the graphics card?
This one has me stumped!
Thanks in advance!
SNazz123

Quote from: jweb2k on 07-October-09, 05:59:52
Oh right. Those are the ones suggested in the HAF 932 case manual. I've used what I think are:
http://images.devshed.com/dh/stories/Building_System_Scratch/scews.jpg
Or am I wrong?? Thanks for your help!
Yes, those appear to be correct one, but they look different than in your photo.
So does the mainboard can boot fine when its outside PC case?
Before mount the mainboard to the PC case:
Motherboard Grounding to case causing No Post
Test the motherboard outside of the case to verify that the motherboard is not shorting to the case and causing a problem
• With only the CPU and heat sink, memory, and video card (or onboard video) connected to the motherboard, place the motherboard on a non-conductive surface and retest the motherboard
• Check the case mounting standoffs to verify that they are lining up correctly with the mounting holes on the motherboard.

HT1926 After successfully upgrading my Apple software, I was able to download iTunes. But I cannot start it up, instead I get this error message, "The file "iTunes Library.itl" cannot be read because it was created by a newer version of iTunes." What ne

I needed to upgrade my iTunes to register and sync a iPhone 5c. I upgraded by Apple Software and finally was able to download the upgraded iTunes. When I try to start iTunes I get this message, "The file iTunes Library.itl" cannot be read because it was created by a newer version of iTunes. How can I repair this?

If you still have an issue you may have to see about using the iTunes version (application) included with Snow Leopard 10.6 from the installer or an another one if available online, and see if that will install.
Sometimes you may have uninstall the bits left in your system by the earlier (or later) iTunes installers; as they all leave a trace and these can stop a different version of iTunes from being installed.
Not sure if the following site/link will tell the method...
•Apple - Support - iTunes - install & update:
http://www.apple.com/support/itunes/install/
•Troubleshooting iTunes installation on Mac OS X:
http://support.apple.com/kb/HT2311
Good luck & happy computing!
ps: i see you resolved this issue. it's magic!

Devfsadm not showing the external storage disk but able to see from OK

Hi,
I have an external storage disk.
Solaris 9 is running on E220R Sun server. I am able to view this disk from the OK prompt using probe-scsi-all.
I have installed SFS packages for V9 and the patches required also. MPXIO is also enabled on this server. But am not able to view this disk when i scan using devfsadm command from the os.
The HBAs are Qlogic 23xx. The driver used is 4.13.x
Please let me know if am missing anything.
Thanks
- Sarat.

can u paste yr cfgadm -al output
try configuring the controller first , if it is unconfigure
also
luxadm -e port # to both cables are connected
luxadm probe # to see the luns
regards

ITunes account not able to purchase on mini but able to buy on IPad

I recently moved and had to change my banking info address in ITunes I tried to purchase a movie from my IPAD Mini but I tune would not let me it came back with an error message that I needed to contact apple support I can only purchase a movies on my IPad only all my information is correct when I go to managed account what to do

Click here and request assistance.
(89426)

Unable to load resource error while starting Integration Repository

Hi all,
Kindly help me with this...
following is my situation :
installed jre1.4.2_08 & jws from sunsite....
i'm getting into XI Start page but repository & directory link is not operational with 'Unable to load resource : <some jar file> '...
in my JWS : File->preferences-->java tab ....there is only one version which is 1.4.2_08....
Pls advise me what should i do ?
surprisingly i've got other people working in different location on the same server which is working FINE
Thanks in advance

Hi Udo,
I just did what that URL advised...but still getting the same error ?
An error occurred while launching/running the application.
Title: Integration Builder
Vendor: SAP AG
Category: Download Error
Unable to load resource: http://in-ccuapp003:50000/rep/repository/aii_ibrep_client.jar
Kindly help....
Thanks

I have a iPod touch 4th Generation and its not wanting to start it stays on the apple logo and when i connect it to the computer it keeps beeping and the apple logo starts to flash but it wont start and i dont know how to fix this I need help!?

I need help to be able to see if I can fix this or something.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

BAPI Response not import in the Integration Repository

Hi All,
When I try to import FM 'BAPI_COMPANYCODE_GETDETAIL', only FM imported, however BAPI_COMPANYCODE_GETDETAIL.response not imported.
Please let us know the reason.
Regards
Naveen

Hi Naveen,
Refer this blogs
Cache Refresh Errors - New Phenomena
Inactive Integration Process (IP) at Run Time
Unable to read INTEGRATION_DIRECTORY_HMI:Undocumented Bug-SXI_CACHE
regards,
Surya

Yosemite 10.10 - Dreamweaver CC 2014 will not open, get the bouncing icon, but fails to start. Illustrator

Hi Not sure if there is a workaround - really need to get DW up and running

Yosemite 10.10 is a beta release. Why on Earth are you using a beta OS on your work box?
Try installing on a stable operating system for which CC was built.
EDIT: See the technical specs required to run DW CC
http://www.adobe.com/products/creativecloud/tech-specs.html
Nancy O.

Firefox won't load when using desktop/start menu icons but loads when starting off links in emails

When I try to start Firefox by the start menu, desktop or any other icon Firefox opens but then freezes and won't respond at all.
If I go to an email and then click on a link than Firefox will open and then load as normal and I can then go about using Firefox.
This has only be happening for the last few days and I have tried all the trouble shots and nothing has changed.

I Have this problem too. won't even start when dbl click the .exe file directly either. but a link in another app or email works fine. I have tried all the stuff here and uninstalled and reinstalled countless times. Using new profile, disabling Norton firewall and antivirus for the installs, only thing that worked was going back to v3.6. and a real early thunderbird too (it was also crashing on starting) Was fine for about three weeks then updated them, The went in stages not all at once and was fine till the newest group of versions. then went back to crashing. this time backgrading did not work. I installed the newest versions Firefox & Thunderbird many more times and by accident found that fresh after a install could open TB first and click a link in a email and FF started ok.
but still will not start from desktop or windows explorer
It is ridiculous to have to open another app to click on a link you don't want to get to where you do want. What is the difference in the links.
ks
also would not start in safe mode or a completely new install.
V.17.0 is the FF thats installed now and at least works as long as I don't try to open it
from desktop or windows explorer, more than a little nervous about going to v.20.

Users not able to create new ojects in Integration Repository

Hi,
    We did a heterogeneous copy of PI from AIX to HPUX. After that we have done few post installation steps w.r.to PI Specific usage type.
    all the developers are able to login to the integration repository, but when they are trying to "Edit" or "Create" new objects they are getting the following error
"You are not permitted to create new objects since the software component cannot be changed".
   this is working with PISUPER user but not with any development user id and passwd.
    any response is higly appreciated.
Thanks
Sourav

Hey NM,
    Thanks a lot for your suggestion. problem got resolved when i did what you said (checking the attributes with developers user id's)
Thanks
Sourav

Not able to start 'INTEGRATION REPOSITORY' but able to start 'DIRECTORY'.

Similar Messages

Maybe you are looking for