Not booting after installation PCI WLAN-card

I own a HP Pavilion Elite m9351.nl.
Recently I replaced the pre-installed Windows Vista Home Premium by Windows 7 Ultimate.
Since then the internal WLAN-card does not wake up from standby. Also replacing the driver with the newest Ralink-driver does not solve this.
Everything else works perfectly.
I removed the internal WLAN-card completely (including removing drivers) and replaced it by a PCI WLAN-card (D-link WMA-547). Now, the computer does not boot. The power supply, fans and lights all work, but the screen stays empty. Not even the HP-startup screen with boot options appears.
After removing the PCI WLAN-card everything works perfectly. When installing it again: nothing!
How do I install a WLAN-card and revive my computer?

I have the same question: suddenly my HP notebook (Win 7) will not boot up unless I turn off the WLAN.

Similar Messages

Snow Leopard not booting after installation in rEFIt triple boot system

Hello,
I have a Core Duo Mac mini, on which I was successfully using a rEFIt triple boot configuration with
Leopard, Windows XP and Linux. After installing Snow Leopard on top of Leopard, Snow Leopard boots directly (without rEFIt showing up) the first time after installation. On the following reboots, rEFIt shows up but when selecting Mac OS, the system shows first the grey screen with the Apple icon, then it shows a grey screen with a "no access" icon and does not make any further progress. I reinstalled several times and at last I even removed rEFIt, but Snow Leopard won't boot anyway.
Can anybody help? Thanks

Welcome to Apple Discussions!
I'd post a bug report here:
http://sourceforge.net/tracker/?group_id=161917&atid=821764
They could probably help isolate your problem.

Windows 7 32-bit not booting after installation... Mac Pro 2,1 Quad Core 2.66

I am trying to install Windows 7 Home Premium 32 bit on my 2006 Mac Pro (Upgraded to 2,1 firmware). However after the installation has been completed and the computer restarts it just reboots back to the start of the Windows set up installation process. If I restart it and select the Windows disk drive at start up with the install disc removed disc drive then all I get is a black screen with a flashing underscore in the top left corner.
Any help would be greatly appreciated.
Computer Specs:
Mac Pro (Early 2006) 2,1 firmware
2x 2.66 GHz Dual-Core Xeon
8 GB 667 MHz DRR2 Ram
Nvidia GeForce 7300 GT
OS X Lion 10.7.5

While not same scenario, the chart you'll see is useful.
Going from Vista U. 64 to W. 7 64 Home Prem. I unknowingly lost support for more than 1 processer
See maximum physical CPUs supported below.
In Vista U. Mac Pro 3.1. Task Manager showed 8 performance graphs (1 graph per cpu/mem).
in Winndows 7 Home Prem., there are 4.
Scroll down to edition comparison chart.
http://en.wikipedia.org/wiki/Windows7editions

Windows 7 will not boot after installation on mac pro

I have a mac pro 2006, and wish to install windows7 on another internal drive, when I follow bootcamp to the point where it says load installation disc for windows 7, it tries to load, but then I get an empty folder with a question mark in it. So then I tried an install on just an internal hard drive not using bootcamp, this time it seems to do a full installation, but when it tries to restart I get a mac symbol, with a no entry sign, any help please.

I can boot in windows safe mode, but, I cannot restart or finish the installation,
for diskutil list i got
#:                       TYPE NAME                    SIZE       IDENTIFIER
   0:     FDisk_partition_scheme                        *500.1 GB   disk0
   1:               Windows_NTFS                         500.1 GB   disk0s1
/dev/disk1
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *2.0 TB     disk1
   1:                        EFI                         209.7 MB   disk1s1
   2:                  Apple_HFS Hitachi 1000 master     1.7 TB     disk1s2
   3:       Microsoft Basic Data Windows                 279.1 GB   disk1s3
for diskutil cs list I got
diskutil cs list
diskutil: did not recognize verb "cs"; type "diskutil" for a list

HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing.
I have tried a "hard reset" a number of times with no success.
When the battery is present the white LED flashes 3 times when the power button is pressed.
Please please help.

Hello Cuffy,
Welcome to the HP Forums!
I understand you notebook will not boot after a series of Windows updates.
Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this information helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

My mac mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone

My Mac Mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone. I had switched the start-up disk back to the original of course. Now all I see is the Apple logo. What should I do? Thanks in advance.

Try disconnecting any external devices, especially hard drives
and try rebooting.
If that doesn't help, then :
If you are running Lion, boot to the Recovery HD and run a
Repair Disk on the OSX partition.
If Snow Leopard, boot to the installl DVD and run Repair Disk.
Also, you may want to bookmark this:
http://reviews.cnet.com/8301-13727_7-57345273-263/troubleshooting-the-boot-proce ss-for-intel-macs/?tag=txt;title
for future reference. It is a pretty good explanation of the
Mac boot process and how to identify where problems may be.

Mac Pro will not restart after installation of Lion. Help!

Mac Pro will not restart after installation of Lion. Help

Reinstalling Lion Without the Installer
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alterhatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.

Can not install WXP driver for WLAN card on my Satellite A200-14D

i have a problem with wireless driver for win xp
i installed win xp and the only problem is the wireless lan driver
help me please

What you mean it does not work? Can you install WLAN card or not? Is your problem WLAN card installation or you can not establish WLAN connectivity?
Please write a little bit more. Is so bad to write few sentences more and describe what happen exactly. Is there any error message or what?

Mac Mini will not boot after Security Update 2008-007

Hello,
A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

Hi Arkku , and a warm welcome to the forums!
I'd certainly give Sig's advice a try first.
If that should fail...
applesetupdone...
This was Posted by: JoseAranda at September 9, 2006 3:48 AM
"OK, restart your computer, hold down Command-s and type in the following:
/sbin/fsck -fy Enter
/sbin/mount -uaw Enter
rm /var/db/.applesetupdone Enter
# The rm command is the remove command which deletes the file.
# Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
reboot Enter
Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
end of posted by: JoseAranda"
Reset OS X Password Without an OS X CD...
http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

MacBook Pro will not boot after software update

MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you). MONEY, MONEY, MONEY is the name of the game. They can cause your computer to crash and still charge you!
Does anyone have an answer to why my computer is showing a little gear spinning for hours? I have tried several things with NO luck.
Thanks-

Run through the list of fixes here
Step by Step to fix your Mac

HT1937 I have installed an app : Birdfield guide in my iPhone 4. But the app is not working after installation. It shows black screen when opened

I have installed an app : Birdfield guide in my iPhone 4. But the app is not working after installation. It shows black screen when opened. I need suggestions to make it work or the reasons for not working.

Yes TeeKnows, try deleting it and download it again. After finished installation if still shows black screen delete it out off 'running apps' by double tapping the home button and swipe it off. If still shows black screen then try fully turning off your iPad (holding the sleep button) and turn back on again.
I hope I helped
thanks
Lydia

Adobe Premiere Elements does not open after installation

Hello,
I have written before last week. I have bought Adobe Photoshop Elements 11 and Adobe Premiere Elements 11.
I had a trial version of Photoshop Elements 11 and with the code I could access the full version.
However Premiere Elements did not open after installation. I did not had a trial version so I first downloaded the full program. I went through the whole installation process and everything seemed ok, no error messages. But when I tried to open Adobe Premiere Elements after restarting the computer it did not open at all. Nothing happened.
I have de-installed and re-installed the program for a couple of times over and over again but with not result. Also tried to download the trial version first and also this didn't work. I checked my Quicktime and updated to the latest version.
I use a Windows laptop: Asus Intel Core i5-2430M, 2,4 GHz
I hope you can help me out!
Thanks!
Inge

Yes I saw it but PSE (refers to Photo Shop Elements??) and I have trouble with Premiere Elements..(so the video program)
The Photoshop Elements worked.
I am not sure what to do here also the link at your reply "working with your operation system tools" didn't work..(got the "broken link error")
thanks
Inge

Firefox will not open after installation. i have tried to install several times with the same results. installation sends a list to firefox each time. need help. willard lee

will not open after installation. i have tried to install several times with the same results. installation sends a list to firefox each time. need help. willard lee

Can you attach a screenshot or link to the instructions you are following?
You are on the 3.6 release and Firefox 7.0.1 is out. You can download and install the latest release from http://www.mozilla.org/en-US/firefox/new/ if you would like to update now. The 3.6 version will be maintained for a while longer, but you should update when you can.

Not Booting after recent Security Patch/Java update

My wife has experienced what many have experienced with the recent update.
MacBook not booting after update (i.e. - "I have no name!")
I have tried everything posted on this topic since 2/13/09, but without any success. Does anyone have the fix for this yet?
Things I have tried:
* I can boot in safe mode (holding "Shift" while restarting)
* I cannot boot from an install disk(s) (holding C while restarting) - I have both a black one from purchase, and two gray ones with purchase from MiniMac
* Booting with verbose - gets stuck at same place as everyone else
Operating in safe mode:
* I can run DU and "repair" drive
* I can see and access the CD/DVD
* I cannot see drive in target drive mode (doesn't ever connect the 2 systems)
* I downloaded the update files from apple and reinstalled them individually (via USB ext Drive) with a reboot in between
* I attempted to update & archive, but I cannot run install CD from any systems disks (see above)
Has anyone figured out how to fix this yet?

Same problem than the other guy who is not mentioning the update in the title.
Powerbook 1.67.
System log said "No user defined computer name" and "using blah blah name" or so.
Mac Os X report (for apple) says:
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x000000003900FF1C PC=0x00000000008FC020
Latest crash info for cpu 0:
Exception state (sv=0x4299D280)
PC=0x008FC020; MSR=0x00009030; DAR=0x3900FF1C; DSISR=0x40000000; LR=0x008FE348; R1=0x2C47B9F0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x008FE348 0x008E0014 0x002E9A80 0x002EB94C 0x0008C248 0x00029234
0x000233F8 0x000ABEAC 0xFF9BA29B
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x8d8000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x48d000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x85a000
dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x87e000
Proceeding back via exception chain:
Exception state (sv=0x4299D280)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x43D0D000)
PC=0x9000AF48; MSR=0x0200F030; DAR=0x0ECA77FE; DSISR=0x42000000; LR=0x9000AE9C; R1=0xBFFFD6C0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x000954F8 0x00095A10 0x00026898 0x000A8204 0x000ABB80
Proceeding back via exception chain:
Exception state (sv=0x4299D280)
PC=0x008FC020; MSR=0x00009030; DAR=0x3900FF1C; DSISR=0x40000000; LR=0x008FE348; R1=0x2C47B9F0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x008FE348 0x008E0014 0x002E9A80 0x002EB94C 0x0008C248 0x00029234
0x000233F8 0x000ABEAC 0xFF9BA29B
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x8d8000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x48d000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x85a000
dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x87e000
Exception state (sv=0x43D0D000)
PC=0x9000AF48; MSR=0x0200F030; DAR=0x0ECA77FE; DSISR=0x42000000; LR=0x9000AE9C; R1=0xBFFFD6C0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC

HT4623 iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

Obviously since you have iOS 7 you're a developer. As a developer, you signed a NDA with Apple not to discuss the iOS on a public forum. Please log in to the Developer Forum using your credentials and ask for help there, lest you risk having your credentials terminated.
Thanks, and best of luck to you.
GDG

Not booting after installation PCI WLAN-card

Similar Messages

Maybe you are looking for