Not enough MTU's for xbox live?

I've been on Xbox Live for about a year and I've had no problems. Last weekend I tried logging on and I'm getting a message saying I don't have enough MTU's to connect. It says I need 1364 or higher. I am running off and Airport Extreme router and I haven't changed routers since I've had Live. How do I fix this? Thanks in advance.
Tom

The MTU setting is under System Preferences-->Network. Click ADVANCED in the lower right corner, then the far-right ETHERNET.
You'll note the bottom item is MTU, and is probably set at 1500--more than enough for XBL. If you want to change it, change Configure from Automatic to MANUAL and that'll give you access to MTU settings.
As others have mentioned, it's very possible this is all connected to the XBL outage today. However, I haven't been able to log onto XBL for the last couple days, so didn't start troubleshooting it until today. Going to wait it out, though, and check after the outage. Seems a waste right now to bother.

Similar Messages

Settings don't have MTU settings for Xbox Live

I've been having problems connecting to Xbox Live. All of my PCs wired and wireless can connect to the internet except for my 2 Xbox 360s one wired and one wireless. Some times it says that there isn't enough MTU or can't connect to the network when I follow their steps to fix it. It just keeps dying on me.
I was wondering if the Configuration page has MTU settings?

I don't know which modem/router you are using (guessing it's some model by Actiontek) but read my post about getting connected to Xbox Live with an Actiontek router. Even if you don't have the same model, you probably will find something useful there. Also, I said this in the post but in case you don't see it, with these modems/routers, you cannot connect wirelessly, you must connect by ethernet or you will get errors. The link is below, hope this helps!
http://forums.verizon.com/t5/High-Speed-Internet-DSL-and-Dial/How-to-connect-to-Xbox-Live-with-the-A...

SSRS 2008 Column Chart with Calculated Series (moving average) "formula error - there are not enough data points for the period" error

I have a simple column chart grouping on 1 value on the category axis. For simplicity's sake, we are plotting $ amounts grouping by Month on the category axis. I right click on the data series and choose "Add calculated series...". I choose moving average. I want to move the average over at least 2 periods.
When I run the report, I get the error "Formula error - there are not enough data points for the period". The way the report is, I never have a guaranteed number of categories (there could be one or there could be 5). When there is 2 or more, the chart renders fine, however, when there is only 1 value, instead of suppressing the moving average line, I get that error and the chart shows nothing.
I don't think this is entirely acceptable for our end users. At a minimum, I would think the moving average line would be suppressed instead of hiding the entire chart. Does anyone know of any workarounds or do I have to enter another ms. connect bug/design consideration.
Thank you,
Dan

I was having the same error while trying to plot a moving average across 7 days. The work around I found was rather simple.
If you right click your report in the solution explorer and select "View Code" it will give you the underlying XML of the report. Find the entry for the value of your calculated series and enter a formula to dynamically create your periods.
<ChartFormulaParameter Name="Period">
<Value>=IIf(Count(Fields!Calls.Value) >= 7 ,7, (Count(Fields!Calls.Value)))</Value>
</ChartFormulaParameter>
What I'm doing here is getting the row count of records returned in the chart. If the returned rows are greater than or equal to 7 (The amount of days I want the average) it will set the points to 7. If not, it will set the number to the amount of returned rows. So far this has worked great. I'm probably going to add more code to handle no records returned although in my case that shouldn't happen but, you never know.
A side note:
If you open the calculated series properties in the designer, you will notice the number of periods is set to "0". If you change this it will overwrite your custom formula in the XML.

I connect my ipad it shows in left side of itunes it is commencing sync then it freezes itunes and i have to disconnct it manually then a error message telling me that there is not enough disc space for ipad which is not correct any ideas folks

i connect my ipad it shows in left side of itunes it is commencing sync then it freezes itunes and i have to disconnct it manually then a error message telling me that there is not enough disc space for ipad which is not correct any ideas folks

i have reset the ipad and restored it to no avail

Is there any way to use a MacBook Pro as a router to set up a wireless connection for XBOX live.

Is there any way to use a MacBook Pro as a router to set up a wireless connection for XBOX live.

Mac OS X 10.6 Help: Sharing your Internet connection

Error msg - not enough memory available for this task - chm file

Hi All
I am using RoboHelp for HTML 8.0 and creating chm file. I am using context sensitive help and the F1 key functionality. I have in the past created some map ID's with F1 and they have worked properly with our company software application. Now, I have a different database with our company and a larger help file and it is not working. I am told that the database should work. I also have lots of memory. I am working off of my hard drive which is where the .exe is for the company application and my chm file. I can open my .chm file. When I go into the application and press F1 where I created the map ID;s I get the message, not enough memory available for this task and also topic not available. Quit one or more programs to increase memory.
I have lots of memory and my file is only 598kb. I also only have RoboHelp and the application running. When I did a search, I found an article for a fix from 2004 from Adobe - Rb_46124 - not sure if this is the fix but the steps dont match since it is old.
Please help me.
Thanks
Caryn

Hi there
Actually, if you were to use FlashHelp output, you might find that the problems are compounded, as now you have the Flash Player and all its idiosyncrasies in the mix.
Cheers... Rick
Helpful and Handy Links
RoboHelp Wish Form/Bug Reporting Form
Begin learning RoboHelp HTML 7 or 8 within the day - $24.95!
Adobe Certified RoboHelp HTML Training
SorcerStone Blog
RoboHelp eBooks

Not enough disk space for asset ecoding

Hi all,
I have a dvdsp project with:
a feature: 3.3 gb
dvd extra: 289
menu assets: 65mb
and shows that it is 3.8 mb all together, but when i try to build/format it stops the build at the menu and gives the error message: Not enough disk space for asset encoding. I was running a test build when this happened. i have yet to add the audio for the extra thinking i still had some room on here to work with.
I have burned dvd's up 4.5 without any issues. any ideas why this is happening?
thanks,
Mark

I'm having the same problem. Except I have tried to switch locations for the Current Build and each time it says Not enough disk space for asset encoding. I have a 500GB raid with almost 400GB free and then another 500GB raid with about 130GB free. I really need help on this pronto!
Another message it now brings up after it starts Encoding Assets: Insufficient disk space for encoding. Please free up disk space on your encoding target drive. Please Help!!
Message was edited by: PapaSnowSmurf

"not enough disk space for asset encoding" error message

I'm using DVD SP 4.2.1 and trying to burn a DL DVD. Every time I try to build the TS folders somewhere, I get the "not enough disk space for asset encoding" message. I have PLENTY of space (over 100GB) where I'm assigning it to create the TS folders. I don't understand why I'm getting the message. Your help is appreciated.

Max,
I think you're onto something here. I noticed that the original disk (an old Iomega Peerless 20GB removable hard drive) was nearly full. I also saved the DVD Studio Pro file for the project to the same drive. I think that, somehow, the application looked to that drive to do something and got a "disk full" message from that disk and gave me the error.
The workaround was to transfer all the assets AND the project file to another hard disk with plenty of space (over 100 GB). The settings for the DVD Studio Pro encoding process remained the same…my computer's internal hard disk with its 30 GB of free space. I re-linked the assets and the disk building and encoding process went smoothly and I'm now the proud owner of a finished DVD.
There's probably something lurking in the background here, but this worked for me.
Thanks for making the suggestion to look deeper! My problem is solved!
Kevin

Error Not enough quota 30 for attendance/absence in ESS Leave Request

Good Morning
I am trying to create a "Leave Request" using ESS with "Floating Days". It has a cuota manual. When trying to create the leave request in ECC all works fine, but when trying to create the same leave request in ESS the following error occurs:
Not enough quota 30 for attendance/absence 0261 on 05.03.2008 for personnel no. 20001140
Some can help me?
Best Regards,
Wilman

Hi,
I would suggest the following :
Step1: Check your IT 2006/IT 2007 for your Absence and Attendance Quotas.
Step 2: You can also verify the same information using the PT50 transaction ( quota Overview)
Step 3: By doing the above you ensure that the person has the required quotas.
Step4: logon to ESS and do the request for leave.if it does not let you, then there is some problem in the config in the ESS. I cannot tell you this from top of my head. We need to look into the portal to see what exactly the problem.
regards
Vijay

": Not enough physical memory for SHM_SHARE_MMU "

Dear ALL,
": Not enough physical memory for SHM_SHARE_MMU "
This is an error message which occurs while trying to mount the database on startup. I've two database running of solaris. DB1 is running with 700M shared pool size. I want to run the DB2 database with 400M. But if i specify 400M shared_pool size on DB2 it is not mounting. It is only mounting when I specify 200M size of shared_pool. Machine has 4cpu and 4gb of RAM.
I've configured the kernel and shemaphore parameter according to the oracle process.
Any thoughts or suggestions appreciated.

The whole SGA must fit into physical memory (SGA=shared_pool_size + (db_block_buffer*db_block_size) + log_buffer + java_pool_size).

HT2729 Downloaded 2 movies on iPad, 1 on desktop to watch during air, but unableto move desktop movie to iPad; not enough iPad memory for 3 movies. After 1 movie is watched & deleted will I be able to download already rented 3rd movie without paying fee

Downloaded 2 movies on iPad, 1 on desktop to watch during air trip, but unable to move desktop movie to iPad; not enough iPad memory for 3 movies. After 1 movie is watched & deleted will I be able to download already rented 3rd movie without paying fee again?

1. No
2. You can only transfer a rental to an Apple TV 1, which Apple TV do you have.

Not enough USB Ports for charging ipod ?

not enough USB Ports for charging ipod ?

If all your ports are in use, try buying a USB hub, they are inexpensive and will give you several more ports. Google for them.

Main Menu:Not enough disk space for asset encoding

i tried to burn my project first i got an error that in track 1 i've got no assets/videos and i added an asset, then a problem with the story and dragged the same story in both columns.. now i tried to burn again and got this error
Main Menu:Not enough disk space for asset encoding
Build cancelled
Building was not successful. See log.
any help appreciated. Thanks in advance

Sounds like your hard drive is getting full. You need as much space on your drive as you can get - at least as much as the disc contents, twice. If you are burning a DVD-R at 4.7Gb then allow ten Gb free space before you start.

Instagram, Facebook, Twitter photos not loading, Getting Kicked off xbox live, random drop outs.

Hi everyone, Here's an issue for you to solve. Im sure it can't be fixed, and I know multiple people that have this issue, and it is unnacceptable. Before I start, here is the router I am using: Telstra Gateway Max. Ok so heres the problem. I have an android phone, well two on my network and they both have the same issue. The iPhones and iPads seem to be OK. i don't have these issues on the computer either (Macbook Pro and Dell Inspiron). When I go onto instagram for example, all of the text loads just fine, but the images just sit on 0% and stay like that until it says unable to download. Facebook is usually ok, but sometimes has the same issue, and Twitter, same as instagram. This also happens on the Google Play Store when trying to download apps, and other random things. I have tried on the 2g and 5g networks and both same issue, but strangely enough, as soon as I connect to 3G/4G network, everything loads great. Why should I have to use my data when at home? Whats the point of paying $200+ a month for a service that doesn't even work! Also, with Xbox Live, this happens on the 360 and Xbox One. I have Two 360's on the network, one being wired (ethernet), the other on wifi. The xbox one is also connected to the same switch as the wired 360. Don't give me any of that garbage about buying a new switch, because this one works perfectly fine.
I have a moderate NAT type on some games, and sometimes I just get randomly disconnected. I have monitored the lights on the router, and they stay normal, some flashing, some solid. Basically, everything is normal. The other xbox's drop off at random times. The annoying thing is, when I connect to the Telstra Air network (off my router) everything loads fine on my phone, and I don't want to be forced to use that terrible 3mbit connection. Oh and while I'm at it, the telstra air app says I don't have a valid account, even though when I manually connect to telstra air through wifi settings on my laptop or phone, it works fine. Back to the xbox, I have forwarded all the ports needed (SHOULDN'T HAVE TO DO THAT), I have changed my firewall to low... Basically, Telstra, get your **bleep** together, and help me with my issues, or give me some pointers.

So someone else with Android devices on an entirely different network seems to have the same issues. This doesn't rule out the Android devices at all, in fact it suggests maybe there is more to it
The only way to make sure it's not the other switch introducing problems is to take it out of the equation. That means running direct connections to the modem. I realise it might be a pain in the rear end though. I user ethernet over power for one of xboxs.

Port Forwarding for Xbox Live

My eyes are burning from trolling the boards all day. Just picked up an AEBS (12:33 PM CST, 4/20/08), firmware's at 7.3.1, connected the ol' xbox and got a "moderate" on my NAT test. Thats fine, totally expected, no big deal, right? So here's what I do:
1. Assign static ip ads to all machines on the network (xbox is 10.0.1.3)
2. Check to see if NAT is enabled in airport utility: Yep.
3. Enter in the ports as usual:
Public UDP Port(s): 88,3074
Public TCP Port(s): 3074
Private IP Address: 10.0.1.3
Private UDP Port(s): 88,3074
Private TCP Port(s): 3074
The above, BTW, is exact as far as commas and spaces go.
4. Update!
Then, NAT test= Moderate.
OK, it'd be nice if there was a standardized way to forward ports on all routers, I think, no big deal, just need to do a little tinkering.
I put a space after the comma between 88 and 3074, i.e., instead of 88,3074 I did 88, 3074. Moderate. I tried putting a dash in there (88-3074) wouldn't even let me do that, but of course we all already knew that. Tried rearranging all the ports randomly (3074,88). Nope. Well, even though I just gave the machine a static ip address, might as well try a DHCP lease: enter Airport ID. Nothing. Try it again with Ethernet ID. Nothing. I've got an idea, I'll make multiple separate port mapping profiles:
xbox 1: Public UDP Port(s): 88...
xbox 2: Public UDP Port(s): 3074...etc.
NAT test= Moderate.
Hmm, Oh they make port forwarding management software? Lighthouse, eh? I'll try that...oh, it doesn't do anything: Moderate.
I tried a bunch of other things that I knew would be futile, but I've been working on this thing for a couple of hours now and I can't remember them...Oh and by the way, for those not familiar with xbox live: "Moderate"= not good.
I'll telepathically make you feel better if you can help me out.
Love ya,
Boo

Thanks for the prompt reply Duane. Just to clarify: I need another wireless router? I thought airport express was one. I was trying to configure the ports of the airport express's basestation. My connection system is:
-An ADSL 2mbps connection that comes into my home from a phone line and into a D-link GLB 802C modem
-This connects to an Airport Express
-My macbook pro uses the net through the wifi signal provided
-I connect the macbook pro to the xbox through an ethernet cable (mainly because it's far from the adsl router)
I have read that one can forward ports with airport express...

Not enough MTU's for xbox live?

Similar Messages

Maybe you are looking for