Not recording from USB keyboard using sound module

I have a USB keyboard and Poizone sound module but nothing gets recorded into AA3 when I record to a track. Track is armed to record, soundcard is selected (analog in) but nothing. What am I overlooking? Thanks.

To record the output of another application in Audition, you'll need to configure your default Windows recording port to be "What You Hear" or something similar, if that is an available option. Right click the speaker icon in your Windows system tray, and choose to adjust the Recording Properties. Here, depending on your OS, you are given a list of different input ports on your audio device: Microphone, Line Input, CD, and often, What You Hear. This just routes the output port back as an input so other programs can record this stream.
Not all audio devices offer this, so it may not show up. In that case, you'd probably need to route your output to a mixer, send a feed back to the Line Input port on your audio device, and listen via headphones through the mixer. Note that you'll need to disable software-based monitoring to prevent feedback and that you'll definitely want to turn off system sounds in case someone sends you an e-mail or an IM while you're recording.

Similar Messages

Which Mac is best for music purposes? I want to mix music recorded from MIDI and live sound, and also want to use Sibelius to play music in. I'm looking at MacBook Pros; any tips? 13" or 15"?

Which Mac is best for music purposes? I want to mix music recorded from MIDI and live sound, and also want to use Sibelius to play music in. I'm looking at MacBook Pros; any tips? 13" or 15"?

I would think a 15" with the i7 CPU. You can get a 13" with the i7 CPU but the 15" has a dedicated graphic chip along with the intergrated one.
You will also need to upgrade the hard drive to a faster 7200RPM model instead of the standard 5400RPM model that comes with all MBPs. The Sibelius website recommends the 7200RPM or a SSD. You will also be better off installing 8GBs of RAM.
Both of those upgrades can be made after you buy a MBP for much less then Apple charges for the same upgrades and you get to keep the original RAM and hard drive.

HP Pavilion 11 x2 not booting from USB

I have tried everything I can think of but my HP Pavilion 11 x2 will not boot from USB...I have Windows 10 currently installed on it and need to boot from USB to allow me to install a new OS on the machine.
I have gone into hte bios...(which I can see is a locked bios with very limited options)....I have turned off the Secure Boot option and have set the USB has the first boot device.
But when I hit F9 on startup...it just gives me 2 options:-
OS Boot Manager
Boot From EFI File
I have tried Boot from EFI File...but this does not work..
I know the USB is configured correctly as I can boot from it on my desktop computer.
How can I get this to work?
Thanks in advance

hi,
i stumbbled into your thread while i was looking for a similar answer for my Pavilion X2 10".
mine was delivered with win 8.1 with bing. it was alright to use, but i was unable to bring this machine to connect to my office domain. due to the lack of networking features which is only available in the pro or enterprise version of win 8.1.
i tried many ways to load in a win 8.1 pro os. the disc is authentic, keys are authentic, usb stick or optical drives; it makes no differences. the machine just refuse to boot into the usb disc / stick like all other previous system does.
there isnt an option for the bios to go into legacy mode. however there is an option to turn off the secure boot, but that does not gives legacy support to the make the system boot to usb.
i had probably done the same things you tried, no matter what setting is done to the bios, there is always only 'os boot manager' and 'ueif' when i hit boot sequence (f9).
had tired everything that i can think of, talking to HP was like talking to an answering machine, and they were asking the most bacis questions ... "were you able to select 'legacy boot' from the bios menu?" ... even when i tell them there isnt a legacy boot option in the bios ... they were too amature .
i concluded that the only way to boot to usb is to do it in uefi with secure boot off and encryption turn off in win 8.1 (else it will bring u to bitlocker).
but i am still unable to boot into the usb media to install win 8.1 pro today. i gave up.

How to read a data from USB port using JAVA

hi all,
i need to know how to read a data from USB port using java. any API are available for java ?.........please give your valuable ideas !!!!!!!!!
Advance Thanks!!

You can do this. Please use this link
[http://www.google.co.in/search?hl=en&client=firefox-a&rls=org.mozilla%3Aen-US%3Aofficial&hs=uHu&q=java+read+data+from+usb+port&btnG=Search&meta=&aq=f&oq=]
What research did you do of your own? Have you done some testing application and tried yourself??

How to read records from Relationship table using ABAP API's

Hi All,
I need to retrieve the records from Relationship table. In Java API's I came to know there is an option to retrieve this. I could not find anything in ABAP API's. Is there any option in ABAP API's to do this.
Please Suggest.
Thank You,
Gajendra.

Hi Gajendra,
You can mainly read records from MDM (in a DDIC structure) using ABAP API's using the following function modules/methods:
1. RETRIEVE: This is used to generically retrieve records from tables. Attributes and Values can also be retrieved.
2. RETRIEVE SIMPLE: Retrieve records from MDM in a simple way.( simple data types).
3. RETRIEVE CHECKOUT: Retrieves all checked out ID's.
4. RETRIEVE ATTRIBUTES: Retrieves attribute(s) from a Taxanomy table.
You will find all these methods in the following interface
Interface : IF_MDM_CORE_SERVICES
Hope it helps.
*Please reward points if found useful.
Thanks and Regards
Nitin Jain

Active Directory cn field not updated from sap HR using ldap.

Hi,
Apologies if this is in the wrong forum area.
I am using the LDAP facility to create and modify Active Directory records from sap HR. Initially, the name field cn that was coming across into AD was in the format of the logical system and employee number, eg, RD4CLNT22000000711.
I then implemented the BADI HRLDAP_ATTRIBUTES which then changed this name field cn in the active directory listing to the format; surname, forename.
It works fine when I create a new user, however the problem comes when I update the persons name in the sap hr module. The data that comes across into Active Directory shows the change to the persons surname sn, forename and displayname fields is there but the cn field is still showing as the previous name.
In short, when a new user is created, the cn field in active directory is correct
(surname, forename) but when the employees name is modified, that change is not brought across to the cn field even though the surname, forename and displayname fields are updated correctlyon AD.
We are on release 4.70.
Anyway, if anyone could help I would be very grateful.
Thanks
David

Hi
The problem it is causing us is that the cn field is incorrect and does not mirror the change in sap HR, therefore the Active Directory entry for the employee is not totally accurate.
When an employee changes their name in SAP HR - usually their surname, we would then want to update the employees active directory account to show this change and this includes the cn field also. At the moment the firstname, lastname fields do get updated with the change so we would want the cn field to show this as well otherwise the cn field would be incorrect and not match up with the employee's AD firstname & lastname fields.
Dave

My iPod Shuffle is not charging from USB

Hi,
My iPod Shuffle is perfectly operationnal when connected to my laptop thru a USB port. I can see it with iTunes et it syncs perfectly. The only problem, it does not charge. I see the yellow light flashing for a few seconds, while it syncs and then nothing.
I run Windows 8.1 on an ASUS laptop. I have disabled the USB suspension. Driver is not authorized to turn off the port to save energy.
When I connect my iPod Shuffle to a desktop computer (running Windows Vista), everything is fine.
Any clue?
Thx

I don't know where "fix" this will be (Microsoft, Asus, or Apple), but this may be what's going on...
When an iPod is NOT set to Enable disk use (or Manually manage music), iTunes only mounts the iPod's disk when syncing. The rest of the time, the iPod's disk is not mounted. There may be a "feature" on your laptop, and/or in Windows 8, that attempts to save energy by putting the USB port into a low-power mode, when the connected storage device (the iPod in this case) is not mounted. When iTunes unmounts the iPod's disk after syncing, it may look like an external storage device that no longer needs full power, even though an iPod needs full power to charge its battery.
When an iPod IS set to Enable disk use (or Manually manage music), iTunes keeps the iPod's disk mounted continuously. Therefore, the USB port stays at full-power mode and the iPod's battery is able to charge.
I know you said
I have disabled the USB suspension. Driver is not authorized to turn off the port to save energy.
but maybe that setting is not working properly (as it relates to iTunes/iPod), and that's the cause.
A desktop computer does not run on battery power, so it may not have this feature; saving energy is not a high priority when the power source is the wall outlet, not a battery. Or, Windows Vista may not have this feature. Therefore, the USB port gets full power whether the connected storage device is mounted or not.
One additional test you can try is to see if it makes a difference if the laptop's power adapter is connected or disconnected. When the power adapter is connected, the laptop has "unlimited" access to energy from the wall outlet (like the desktop), so maybe the USB ports stay at full power all the time.

Optical drive trashed and MB Pro will not boot from USB image

Hello,
New here but I have searched and tried all I know to get this MBP working right again. My disk drive is trashed and has been for some time now, this is why I have a bootable version of Snow Leopard on an 8G flash drive. When my MBP began acting funny recently and I went to disk utility to verify permissions and the disk. Both failed = must boot from disk to repair, thus my issue. For some reason by MBP will not boot from the usb image I have used previously??? Pressing C or Option during startup does not work. If I press Option, I only get the harddrive option, C yields nothing and the computer boots normally.
Please!! let me know how / what you would do to resolve this. I don't understand why I have previously been able to boot from this same file on the same drive previously to repair my disk / permissions but cannot do so now. FWIW, I tried placing the file (OSX) on my external HDD to boot from, this did not work either (USB HDD).
Thank you in advance for your input!!

It isn't clear what you mean about your HD being trashed or which disk (HD or USB drive) you are trying to repair, but either way you need to start up from your Snow Leopard installer DVD & instead of installing anything go to the Utilities menu & run Disk Utility from there to repair either or both of the disks.

Imac 21" mid 2011 can not boot from USB device?

Hi,
hope someone can help me.
Bought the new imac 21" and replaced the superdrive with a ssd drive.
Works great but it seems that the imac is not able to boot from any usb device.
I put my osx install disk in my external dvd drive and powered my mac.
While booting up (pressing cmd) the mac does not recognize my external dvd drive. This works great with my MBP late 2008. But the imac can not boot from the dvd drive. Also pressing "c" while booting does not work. Doing that a grey screen appears and after some time mac boots from hdd.
So i installed mac os via target mode over firewire withbmy old imac. This works.
But now i want to install windows on a bootcamp partition.
I can't boot from the windows 7 professional dvd, too. So i tried to create a bootable win 7 thumbdrive. Mac can't boot from this too. Reading many threads in some forum i tried with rEEfit. Reefit shows the usb thumbdrive whike booting, but using this will end in a black screen error from bios: "no bootable device....". Tried a knoppix on the usb thukbdrive, too.... No bootable device....
It seems that there is no way to boot from ANY external usb device like dvd drives or thumbdrives......
What more can i do? I tried for 2 evenings now, but nothing worked out for me......
Currently i don't see any any to install win 7 without an internal superdrive, but can this be??
Thanks for any comments.
Kwicks

Internal is definitely the easiest but you can boot from external HD or external optical drive, the mac is just very picky on what works and what doesn't.
For an external drive or usb stick it has to be GUID partition table and have 10.4.5 or better installed on it, for more info check this link out ( http://support.apple.com/kb/ht1948 )
Hope this helps,
Joe

Read records from VALUES OBJECT using the INTERATOR

Hi
I'm trying to read records from my value object with interator these way:
ValidaUsu usuVO = new ValidaUsu();
for (Iterator it = usuVO it.hasNext(); ) {
System.out.println(" User from VO: " + usuVO.getUsuario());
But i don't know what i`m doing wrong ?
Could help me?
Thanks

Hi Gajendra,
You can mainly read records from MDM (in a DDIC structure) using ABAP API's using the following function modules/methods:
1. RETRIEVE: This is used to generically retrieve records from tables. Attributes and Values can also be retrieved.
2. RETRIEVE SIMPLE: Retrieve records from MDM in a simple way.( simple data types).
3. RETRIEVE CHECKOUT: Retrieves all checked out ID's.
4. RETRIEVE ATTRIBUTES: Retrieves attribute(s) from a Taxanomy table.
You will find all these methods in the following interface
Interface : IF_MDM_CORE_SERVICES
Hope it helps.
*Please reward points if found useful.
Thanks and Regards
Nitin Jain

APD vs Read from a cube using Function module

Hi,
Please could someone tell me which is the best practice for the below case:
I want to sent information for one cube to another and in the transformation read from a third cube. I think I have this two options:
- Option1: In the transformation use the function module to read from a third cube and take the information that I need.
- Option2: Use APD and send the information of the third cube to a DSO, and in the transformation read from the DSO, instead from the third cube.
Thanks in advance for your collaboration.
Judith.

Hi,
If I compare option 1 and option 2 then there are many complexities involved in option 2. First of all you will have to create an extra DSO just for look up purpose and this will occupy extra DB space.
You will always have to do the data transfer from cube to DSO and you need to make sure that DSO data is perfectly matching with Cube so as to populate correct values during lookup.
But in case of option1 you are simply reading data from original cube using FM so you don't need to worry about data quality for lookup. The only thing here you will have to check is how much time it takes to read data from cube. As you will be writing extraction code in Start routine and use internal table in field routine.
I hope this will not impact much on your performance.
Regards,
Durgesh.

Completion not recorded in LMS when using IE 11

Has anyone else had problems with course completion not recording in the LMS when using IE 11?

Yes, we are experiencing the same issue. It appears that the course is trying to re-initialize upon termination...
We may have to force using Compatibility mode which can be driven from a meta tag in the index page header...
<meta http-equiv="X-UA-Compatible" content="IE=EmulateIE11" />
Anyone tried this?

Deleting records from a Database using JTable

Hello!
I have a JTable that displays records from a database and a Jbutton .
If i press the button i want that the record coresponding to selectedRow(from the JTable) to be erased from the database.How can i manipulate selectedRow from JTable to do that?
Pls any suggestions (and if it's possible +code)?
Thanks!

Hi Margot,
Let's assume that you have created a table using vectors. Simply remove the element from the vector at row selected and redraw. Maybe not the greatest solution but should work.
Vector rowData = new Vector();
//read in values for each row
Vector headers = new Vector();
//add your headers
JTable table = new JTable(rowData, headers);
int row = table.getSelectedRow();
rowData.removeElementAt(row);
table = new JTable(rowData, headers);HTH,
Chris

How to delete record from table control using BDC?

Hello friends,
I am running a BDC program to delete records.
I have file with following records and i got these records into t_itab.
Material     Plant     Start date     End date     Cost
MQ100001     S001     09/01/2008     09/31/2008     55.00
MQ100004     S002     09/01/2008     09/31/2008     56.00
MQ100008     S003     09/01/2008     09/31/2008     57.00
Now, I have BDC transaction in which table control screen which contains following structure.
MQ100001     S001     09/01/2008     09/31/2008     55.00
MQ100002     S002     09/01/2008     09/31/2008     56.00
MQ100004     S003     09/01/2008     09/31/2008     47.00
MQ100005     S004     09/01/2008     09/31/2008     25.00
MQ100006     S012     09/01/2008     09/31/2008     76.00
MQ100007     S033     09/01/2008     09/31/2008     17.00
MQ100008     S011     09/01/2008     09/31/2008     95.00
MQ100009     S002     09/01/2008     09/31/2008     46.00
I have recorded from SHDB in which first record will be delete.
So, when i loop through t_itab,instead of deleting MQ100001,MQ100004 and MQ100008 from BDC screen,
it is deleting MQ100001,MQ100002 and MQ100004 (first record for each process ).
Which i don't want to.
Is there any facility in BDC to put records on top which i want to delete?
Please guide me.
Regards,
RH

One option is to identify the table and find out the location as the number of row which should be deleted from the table and then in the bdc program instead of postioning the cursor on the row 1(using the statement perform bdc_cursor ....(01)), replace the 01 with the row number.
Second option is that if a filter control is available for the table control, then filter the data each and every time with the material number to be deleted and then delete the first row.
Regards
Farzan

Delete records from internal table using another internal table

HI,
I have two internal tables itab1 and itab2 which have same records initially.Later some records of itab2 are deleted .Then i want to delete those records from itab1 also ie,those records not found in itab2 .Is there any method other than looping.
So that itab1 again becomes equal to itab2.
Thanks in advance.
Sowmya.

Soumya,
Itab1 , Itab2 .
Before deleting the records from itab2 move those records to one more internal table itab3.
Now you have deleted records of itab2 in itab3.
SORT ITAB3,ITAB1 by your main key field.
LOOP AT itab3.
READ TABLE ITAB1 WITH KEY key field = itab3-
keyfield.
IF sy-subrc EQ 0.
DELETE itab1 where keyfield eq itab3-keyfield.
ENDIF.
ENDLOOP.

Not recording from USB keyboard using sound module

Similar Messages

Maybe you are looking for