Not seeing command rate

When i go into my bios (version1.4) i want to make sure that my command rate is
set properly for my ram. But low and be hold when i get to the section it should be in, i do not see it. my book says it should be there. any suggestions?
thank you in advance.

C0 revision lack a register for 2T setting that were introdused in CG.
C0 is capable of running 1T , but the memory controller in C0 is more picky about ram than CG which affects many depending on their ram type.
And since it doesn't have that spesific register for setting 2T it's all done auto by the memory controller . Not like the CG wich you can set either one or the other via bios.

Similar Messages

When I go into photos or events under library I can not see my photos, only empty squares. I rebuilt iphoto by holding down option-command keys

When I go in photos or events under library in iphoto I can not see pictures, all it shows is the empty squares. The fotos r there cause when I scroll down with the mouse I can see the pictures for a few seconds. I rebuild iphoto by holding down option-command keys and then iphoto ican. need help please

Hi,
You have managed to post in Applications then iChat within that.
iPhoto is listed under iLife
I have not used iPhoto enough to be able to offer solution for you.
You would be better off posting in the iPhoto Forum (in that link above)
7:40 PM Monday; May 2, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.7)
, Mac OS X (10.6.7),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Can not see long text description of a characteristics in portal

Hi experts,
I designed two queries via Query designer and published them to portal but I can not see the the long text description of "Name" attribute belongs to 0BPARTNER characteristics.
One of the queries shows only the last name of partner in portal while it is showing full name and last name in Bex Analyzer. The other query shows only the key value in both portal and Bex Analyzer.
I want to see long text description in both queries.
For an additional information, I'm extracting data from CRM 5.00 to BW 7.00
What will be the reason for this and how can I solve it?
Can anyone help me for this issue, it's a kind of emergency situation.

Hi,
we have the same problem.
We want to change <b>only</b> in the screen variable the hierarchy text (from default to long\medium text) but even if there's a possibility to do this, really it doesn't happen anything - it' s possible when you start query, in the selection screen inside every the variable there's a command "User Settings" in which manage what you want to see (I put display custom, as text, medium text).
I try to do this also in query analizer, selecting variable (hierarchy) and enter in this (user setting), changing in display custom as text - medium text, but even if I save this settings, really doesn't happen anything.
It seems the system isn't sensitive to this selection...
By now, if someone has an answer, please write us!
Thanks in advance,
Alessandra Mirone

Question: 10gR2 database can not see the 11gR2 ASM diskgroup?

Hi there,
env:
uname -rm
2.6.18-92.1.22.el5xen x86_64
Single server(non-RAC)
note: we don't want to upgrade 10gr2 database into 11gR2 yet. But we created the 11gR2 ASM, then a 11gr2 database on ASM, and plan to migrate datafile in 10gR2 database to 11gR2 ASM
1. oracle 10gR2 installed first version: 10.2.0.3.0
2. then install 11gR2 Grid Infrastructure, and created ASM (version 11gr2)
$ sqlplus / as sysasm
SQL*Plus: Release 11.2.0.1.0 Production on Tue Oct 19 10:30:56 2010
Copyright (c) 1982, 2009, Oracle. All rights reserved.
Connected to:
Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
With the Automatic Storage Management option
SQL> col name form a15
SQL> col COMPATIBILITY form a15
SQL> col DATABASE_COMPATIBILITY form a15
SQL> l
1* select name , STATE, COMPATIBILITY, DATABASE_COMPATIBILITY from v$asm_diskgroup
SQL> /
NAME STATE COMPATIBILITY DATABASE_COMPAT
ORCL_DATA1 MOUNTED 11.2.0.0.0 10.1.0.0.0
ORA_DATA MOUNTED 10.1.0.0.0 10.1.0.0.0
3. in 10gR2 database
sqlplus /
SQL*Plus: Release 10.2.0.3.0 - Production on Tue Oct 19 12:12:31 2010
Copyright (c) 1982, 2006, Oracle. All Rights Reserved.
Connected to:
Oracle Database 10g Enterprise Edition Release 10.2.0.3.0 - 64bit Production
With the Partitioning and Data Mining options
SQL> select * from v$asm_diskgroup;
no rows selected
4. pin the node into css
# /u01/app/product/11.2.0/grid/bin/crsctl pin css -n mynodename
CRS-4000: Command Pin failed, or completed with errors.
Question: 10gR2 database can not see the 11gR2 ASM diskgroup?
please help
Thanks
Scott

What is the output of
olsnodes -t -n
Also, see unix error log and ohasd error log if you find anything in that

My computer does not see my printer

Hi: I am having a problem with my HP Photosmart 4500 printer. My computer does not see it. I have a USB connected to it, have uninstalled and installed the software two time, dowloaded the latest update and nothing. Add to that, I can not connect it by WIFI. WIFI on the printer is on but again, it's no where on any of the screens. The only variable I can think of that has changed has been the router I got recently from AT&T. Everything else works with the WIFI but no computer. I'm running 10.7.5. I have read the install instructions and nothing seems to be working. The one thing I do get from the HP install disc is a message reading the printer isn't recognized but there are no updates in support. OK, what am I missing here?

Try these steps to uninstall the current software using the HP scrubber and then reinstall using the current HP driver available through Apple.
To do so, perform the following steps:
1. Go to Applications/Hewlett Packard/ and then click on “HP Uninstaller”
2. Next click “Continue”
3. Highlight the device on the left pane.
4. Press and hold control+alt+command on the keyboard simultaneously while you click on “Uninstall”.
5. After you do this, you will see a pop up that asks you if you want to uninstall all HP software. Please note, that in doing this, it will remove any other HP printers that you also have installed.
6. Click “continue” and wait for the program to finish.
7. After it completes, reboot your computer.
Once the computer is back on, do the following steps:
WARNING: This is will delete all of your printers.
1. Go into “System Preferences” and then select either “Print & Scan” or "Print & Fax".
2. Right click (or control + click) on the rectangle listing your printers and then select “Reset Printing System”.
After you have reset the printing system, let's make sure you have the most recent HP driver package installed.
You can do this two ways. First, check for any available HP Update's by clicking the Apple icon and then Software Update. If there are any updates available, they should show up here. However, if the printer is connected by USB, it will not show any available updates. The other option is downloading the drivers from Apple's website.
You can download it here: http://support.apple.com/downloads/DL907/en_US/HPPrinterDrivers2.14.dmg
Once you have downloaded the driver package and completed the installation, you will want to plug your printer back in (if you were using a USB connection). After the printer is plugged back in, go into your print settings under System Preferences > Print & Scan. To add the printer, click the plus sign. You should see your printer listed here. If not, click "Add Printer or Scanner." Click the name of your printer and then click "Use:” box. Make sure that says the name of your printer and not AirPrint. If you are using the printer wirelessly, make sure that the printer "Kind:" is set to Bonjour or Bonjour Multifunction. Click "Add" down in the bottom right hand corner.
This will add your printer back using the most recent HP print driver available through Apple. Let me know if this helps resolve your issue or not. If it doesn't, let me know I will see what else I can do.
Best of luck,
Kyle

Migration assistant screw up, Mac Pro not seeing wifi/TC

Hi
I've been using a MacBookPro (MBP) for almost 5 years now, with a 1TB Time Capsule (TC1) using Time Machine (TM). I am the sole user, HDD is 270Gb used/50Gb free; using Mavericks, v10.9.2. On Friday, I used Sophos anti virus home edition, to scan the MBP. It comes up with no threats identified, and I uninstall Sophos.
Yesterday I took delivery of the Mac Pro (MP) with the 3Tb Time Capsule (TC3).
I booted up the MP, with the TC3. I did not, at this stage, connect the TC3 to the internet. Using TM, I backed up the MP. TC3 flashes the amber light.
Using Migration Assistant (MA) I tried to copy the MBP to the MP, 3 times. This did not work. At the point where the target machine has listed what is available to transfer, I click Continue and MA on the MP closes, on the MBP it says something like connection lost. The screen where this happens, lists 3 items available to transfer Application, Documents/Date and Computer settings; with a content of 128kb indicated, which is clearly wrong! The connection was an Ethernet cable direct from the MBP to the MP.
At this stage, I decide to connect the MP to the internet using TC3, there's some settings to be changed on TC3 using Airport Utility and it connects ok. TC3 has a steady green light.
I run 2 software updates on the MP. I surf the net briefly, to make sure it's ok.
I try again to use MA. This time, the dialgoue box listing what's available to transfer is different. There are 2 or 3 more options, colour is present, the font is different, the box is about the same size. The MP would not let me take any screenshots as all other applications are closed when MA is running. I don't think it gave me the size of what was being transferred, but it looked more hopeful, so I Continue and the transfer starts, with an estimated time of 33 minutes.
The transfer completes.
The MBP, as you would expect, has not changed, the MP has, but not in the way I expected. Applications appear to have all transferred (without checking them), no Documents/data and no Downloads appear to have transferred; I ticked to transfer everything.;I know I can reconnect the Ethernet cable and simply copy the data across.
But the main problem appears to be, the MP does not see the wifi.
Ethernet cable is removed.
The MP asks if I want to give permission to eeEvents manager (I presume calendar related) and say yes. It also asks if I want to install a Java run time, no.
In System preferences/Network it tells me a new Thunderbolt bridge has been found and asks if it's ok, to accept it, yes. It tells me the Ethernet cable is disconnected, rightly so; it says Airport is not connected.
I open Airport utility, no sign of the TC1 or TC3 despite it searching. Apart from TC1, the MP, MBP and TC3 are sat within a couple of feet of each other.
I turn on TC1/TC3 (separately and not at the same time, then at the same time), but the MP does not see them. I've reset TC3, rebooted the MP and still the MP does not see it.
I don't get any errors or warnings coming up.
I think my next option is to try and reset the MP to the factory settings, but this won't work, as I've no internet connection to reinstall OS X. No disc is sent with the MP.
Any suggestions as to what to try? Otherwise, I'll be off to the Apple Store tomorrow for a One to One!! :-(
Thanks for any help and Happy Mother's Day!!

Take the MP and connect it via ETH to your main router.
Restart the machine holding down command option R, you should see a spinning globe
Open disk utility and reformat the MP HD as Mac journaled
Then install OSX on this drive

Using an "if not exists" command with a folder on an SMB share

I'm trying to use an "if not exists" command on a folder which is stored on a mounted smb share..
This part of my script is supposed to check if a folder exists and;
If it does - Skip to the next part of the script
If it doesn't - Create the folder.
At the moment it either errors saying that the folder doesn't exist or doesn't create the folder.
I can get this script to work fine using local folder paths but I want to do it on an SMB share..
Here's my script.
Many thanks in advance.
Martin
set username to (do shell script "whoami")
set Media to " Media Files"
mount volume "smb://172.22.8.23/macmedia$"
tell application "Finder"
if not (exists ("smb://172.22.8.23/macmedia$/" & username as text) & Media as text) then
make new folder at "macmedia$" with properties {name:(username as text) & Media as text}
end if
end tell
tell application "Finder"
set mnt to ("smb://172.22.8.23/macmedia$/" & username as text) & Media as text
try
mount volume mnt
end try
eject "macmedia$"
end tell

Hi Camelot,
Thanks a lot for that the script's working as it should now..
I'm still having intermittent problems on some clients where it will only map the root volume "macmedia$" and freeze there.. This is a problem as they can then see and access everyone elses folders from there.
Do you know of a better/cleaner way to do what I'm trying to acheive? All i'm after is mapping an additional drive for student's so they can save larger files to our media server within their own folders.
Is there a way of checking if a folder exisits within an smb share without mounting the volume? Just trying to think outside of the box a bit..
Here's my new script;
set username to (do shell script "whoami") & " Media" as text
mount volume "smb://172.22.8.23/macmedia$"
tell application "Finder"
          if not (exists folder username of disk "macmedia$") then
make new folder at disk "macmedia$" with properties {name:username as text}
          end if
end tell
tell application "Finder"
          set mnt to ("smb://172.22.8.23/macmedia$/" & username as text)
          try
mount volume mnt
          end try
          eject "macmedia$"
end tell
Many thanks,
Martin

Can not see some videos, Can not install Activex 9.o47

My name is Alex, I have been working on getting flash to play
for about 3 weeks.
I have uninstalled both shockwave and flash many many times
using all different sites. I have turned off my firewall,
anti spy, and antivirus when downloading. I have shut
everything down that was running. I have closed everything.
I have restarted each time between downloads. I have then
downloaded the install from many many sites. Closed everything, and
installed.
I have uninstalled from ADD/Remove. I have reinstalled. Now,
when I go to ADD/Remove programs it shows that both Flash and
Shockwave are there.
Seriously, I have downloaded and uninstalled and installed so
many times from so many sites.
Each time the screen shows I have done it successfully. But I
cannot get it to play. I have turned off all popup blockers that I
know of.
I still run my anti virus, firewall spyware etc. But says
there is nothing to prevent Flash from playing some of the pages I
use to see.
I have done a Reg clean. And I have installed after all that
and still does not work.
I am the admin on the computer and I am the only one who runs
it. I use firefox for my browser but I tried to get it in IE and
still nothing.
Everything was going absolutely fine till I done the stupid
mistake of updating my Flash player,
seen then my computer is going banana, I don't understand why
is that,
I can actually see U tube videos, but I can not see other
videos like trailers from IMDB, <Your browser is blocking
display of our video player. If you would like to see the video,
please turn off any ad-blocking or Flash-blocking software that you
are using>.
That's what he said on the screen where the video suppose to
play, I can only see advertising, It should be the other way
around,
and even the news on yahoo I can not see them, only ads.
I had no problems before, no pop up I could see the videos
absolutely fine and especially no ADS and then that days,
I wish I could cancel that day, I'm try to fix this problems
all ready 3 weeks and nothing, I did try everything but nothing.
I have download flash Player 9.0.47.0 manage to install but
found impossible to install Activex 9.0.47.0 seems to be impossible
I do know why. disinstall everything reinstall but nothing,
# Select Start.
# Select Run.
# Type cmd
# In the command window, type the following:
uninstall_flash_player.exe /clean
The answer is: uninstall_flash_player.exe is not recognised
as an internal or external command,
operable program or batch file.
does not work, try million of time, does not work.
Does anybody know why?

You are not the first one to notice..................
http://forums.adobe.com/thread/748720?tstart=0
Please do submit a request for it to be changed www.adobe.com/go/wish

Why am I not seeing my photo images in iphoto?

When I open up iPhoto, I do not see the actual images of the photo..just a blank icon where the photo is. Once I double click on the icon, it will appear. What is happening here and how do I fix it so I can see the images displayed without having to click on them?

Back up your iPhoto library, Depress and hold the option (alt) and command keys and launch iPhoto - rebuild your iPhoto library database
If that does not fix it download iPhoto Library Manager - http://www.fatcatsoftware.com/iplm/ - nad use its free rebuild command to create a totally new library leaving the existing one untouched
LN

How can I set up my contacts so that I do not see all of them on ipad from iCloud?

How can I set up my contacts so that I do not see all of them on ipad from iCloud? I don't need/want to view contact info for casual contacts on the ipad. (I.e. contacts entered so that I can identify a caller for ID/screening purposes)
Also would like to limit email contacts from yahoo- no need to view emails for every "safe list" address.
Thanks!

Keyboard shortcut for FullScreen is command + control + F
For more on this:
http://support.apple.com/kb/PH11941

Does not see iPhone

(moderator - tried posting this in iPhone section but got no replies)
I have 3 Macs:
Mac Book Pro (iTunes sees iPhone)
Home G4 867mhz running OSX 10.4.11 (iTunes sees iPhone)
Work G4 867mhz running OSX 10.4.11 (iTunes does not see iPhone)
The iPhones primary computer is the Mac Book Pro and this is the one I use for syncing.
Any ideas why my work G4 does not recognise the iPhone?
thanks
Pete

Console.app has the following in it
Nov 10 13:07:39 jack-bregmans-power-mac-g4 [0x0-0x16016].com.apple.iTunes[0]: Child: Can't read length for data
Nov 10 13:07:39 jack-bregmans-power-mac-g4 [0x0-0x16016].com.apple.iTunes[0]: Child: NULL command dict read, exiting...

DW 4 not seeing GoLive .site file!

I have several sites created in GoLive 7. I downloaded the GoLive 9 free trial, brought them over into GL9. Then I did the "Convert Site to New Structure" command as I have seen suggested. Downloaded the GoLive to DW migration extension and installed it. So far so good.
But when I go to Import GoLive Site, and navigate to the folder where the site file is (there are actually several, only one is the current one), Dreamweaver does not "see" the .site files, even though when I look in the window in explorer, they are there. All I see are the web-content, web-data, and web-settings folders, but no .site files at all.

rich.leach wrote:
> no, the file was not open, and I tried all of the
various search options
> available in the DW Find feature, especially after this
issue was discovered.
> And if DW customers are required to register particular
file types with DW in
> order to have the application successfully search those
files, that would
> warrant a special instruction set or at least a dialog
box somewhere in DW,
> wouldn't you agree???
This is an issue that I have never come across before. You're
using a
non-standard filename extension, so it doesn't particularly
surprise me
that Dreamweaver ignored it. Have you tried entering
.properties in the
list of filename extensions, as I suggested? If that works,
your problem
is solved. All that's needed is for the documentation to be
made more
explicit.
On the other hand, if your filename extension is likely to be
in
widespread use, perhaps it's something that should be added
to the
standard list of files that Dreamweaver handles. Submit a
feature
request to the Dreamweaver team.
http://www.adobe.com/cfusion/mmform/index.cfm?name=wishform
David Powers, Adobe Community Expert
Author, "The Essential Guide to Dreamweaver CS3" (friends of
ED)
Author, "PHP Solutions" (friends of ED)
http://foundationphp.com/

PowerBook G4 does not see optical drive in System Profiler

I have a very strange situation in a powerbook G4 (1.67ghz, hi-res 15" screen).
I bought the laptop non-working, installed a new power board (plug on old one was fried!) Installed a 250gb HD which I had installed OSX on in another G4 laptop, and it booted up fine, or so I thought.
When I put in my Leopard install DVD to install over the existing 10.4 Tiger, the disc spun up, but would not mount - would not eject - and when I checked the System Profiler the superdrive was not recognized by the powerbook as being present on the ATA bus. The hard drive, of course, was seen on the ATA bus.
I thought the superdrive was bum, so I installed a known-working combo drive I had around from a previously parted laptop (Apple branded) and experienced EXACTLY the same situation.
Other things I have tried included using jumpers to manually set the hard drive to slave and cable select (from the factory, with no jumpers, it is set to master), thinking that perhaps the optical drive was somehow seen as master or cable select. All possible jumper settings I tried made no difference.
Booting from external firewire hard drive shows exactly the same situation on the ATA bus, EXCEPT (and this is where it gets just weird enough to pique my curiosity and keep me trying to fix it) - When I boot from the external drive WITHOUT AN INTERNAL DRIVE installed, the SUPERDRIVE SHOWS UP ON THE ATA BUS of the System Profiler! I have not yet seen both at the same time, but I can get one or the other to show, depending on, apparently, the presence of the internal hard drive.
Am I missing something here, or am I to assume a fault in the IDE controller of the logic board?
I have never seen this laptop working properly, but the seller I acquired it from stated that the optical drive worked fine until he fried the DC in-board, presumably with a faulty power supply. He had removed his hard drive to save the data on it.
Thanks for any help or clues that anyone might provide.
See another post with similar situation (archived, or I would have jumped on that thread):
http://discussions.apple.com/thread.jspa?threadID=1862129&tstart=0
Ray

Well, I am happy to report that the situation is resolved with my powerbook not seeing the superdrive, but I still do not really understand exactly why it was unavailable in the system profiler as I originally posted.
My particular solution was to wipe out (erase) the hard drive, zapped PMU, zapped PRAM, did the reset-nvram in open firmware, rechecked to make CERTAIN the proper cables were installed properly, and Now I just completed a fresh install of Leopard from the previously recalcitrant superdrive, to the now-clean hard drive.
My BEST GUESS as to what was wrong with the situation from the outset may have had something to do with where the hard drive came from and how that operating system was installed. (the OS was on the HD when I installed it) In hindsight, perhaps doing all the resets, as well as repairing permissions MIGHT have done it, but I got caught up in thinking it might be cables or something.
So, I would advise others with a similar problem to:
repair the hard drive
repair permissions on the hard drive
reset PMU
reset PRAM
boot to open firmware (hold command-option-o-f at boot) and type "reset-nvram" (without quotes) enter, the type "set-default" enter, then type "reset-all" enter
cross your fingers, knock on wood, and boot! See what happens....
if no glory, THEN look at cables (make certain they are the CORRECT cables and that they are seated properly) I bought a hard drive cable and an optical cable from ebay sellers with assurance that they were the proper cables, and NEITHER had the same part number as the original cable which I suspected faulty, and that in the end are actually GOOD! GO BY PART NUMBERS! do not accept someone elses assurance that their cable is the proper one!
then suspect faulty optical drive - if possible swap another drive in and check.
if a second optical fails, then SUSPECT logicboard, but before you invest in a new logic board ($$$$$) try putting a freshly erased HD in and just see if that helps.
good luck to you all with your mac troubleshooting!
and thanks to all who read and pondered....
I will mark this case "answered" though it is more closed than truly answered.
I am very relieved that the fault did not lie in any of the major components (or even the minor ones for that matter)
It turned out to be only software/installation/settings, even though the symptoms certainly seemed to point to a hardware issue. It pays to try the resets and repairs!
Ray

How to set the command rate?

Hi mates!
How can I set the Ram command rate in the bios? I can't find anything about it. I also watched in the manual but nothing

gotti, I've found a way to do it, but it has to be set manually each time you reboot. I'm trying to see if there's a way to have it stay, or at the very least have it set automatically at every boot. stand by

Solaris 9 not seeing second path for few LUNs.

Hi,
We got 59 LUNs from EMC storage team. We are able to see all 59 LUNs in path. We are seeing 53 LUNs on second path, for 6 LUNs system is not seeing second path.
With syminq output we are able to see the device on both paths. Both HBAs has same number of entries in /etc/path_to_inst file. We rebooted and ran update_drv command few times still system is not seeing second second path.
Any idea why we are not seeing second path?
Here is sd.conf entry. lun 27 is good, lun 86 missing second path
name="sd" parent="lpfc" target=17 lun=27;
name="sd" parent="lpfc" target=17 lun=86;
name="sd" parent="lpfc" target=18 lun=27;
name="sd" parent="lpfc" target=18 lun=86;Thanks
SR

Hi,
We got 59 LUNs from EMC storage team. We are able to see all 59 LUNs in path. We are seeing 53 LUNs on second path, for 6 LUNs system is not seeing second path.
With syminq output we are able to see the device on both paths. Both HBAs has same number of entries in /etc/path_to_inst file. We rebooted and ran update_drv command few times still system is not seeing second second path.
Any idea why we are not seeing second path?
Here is sd.conf entry. lun 27 is good, lun 86 missing second path
name="sd" parent="lpfc" target=17 lun=27;
name="sd" parent="lpfc" target=17 lun=86;
name="sd" parent="lpfc" target=18 lun=27;
name="sd" parent="lpfc" target=18 lun=86;Thanks
SR

Not seeing command rate

Similar Messages

Maybe you are looking for