Not working USB and Bluetooth GPRS connection with LG KS360 Tribe

Hello, I just bought an LG KS360 Tribe and I can't use it to connect to the Internet. I also successfully use a Nokia phone with USB connection.
With the LG phone, when I click on "Connect", it tries to connect to the Internet for a few seconds, then the connection drops. on the phone I can see that 0KB of data have been transfered.
Bluetooth connection is the same. I use the Generic GPRS/3G driver.
Please help me with this one...
Thanks

Resolved! I've searched for similar problems with generic LG phones. This is what I found: http://www.taniwha.org.uk/
I've download the zip file http://www.taniwha.org.uk/files/Generic3G2007-02.zip
(just search for "Generic 3G Scripts" inside the page).
Then:
0. Unpack the zip
1. Copy the "Generic 3G *" scripts in "/Library/Modem Scripts"
2. Start the Network Manager
3. Connect the LG KS360 phone using the USB connector
4. Install the new device
5. Where you should put the phone number, write the APN address
6. In user I've inserted "none". Same thing in the password field.
7. Click on Advanced and select the driver "Other" and "Generic 3G CID1".
8. Click "OK", "Apply" and "Connect".
All works for me.

Similar Messages

MSI GE620DX not working touchapd and bluetooth

good day
I have a question on my MSI
I have a MSI GE620DX where my motherboard deteriorated in version 2.0 which has Windows 7 64bit I bought a new board but in version 1.0 and I installed Windows 8.1 64bit there and not me Bluettoth (constantly on and off), and even not tuchpad ...
I did UPDATE BIOS to version E16G5IMS.10R (build 24.10.2012)
I tried a firmware update but I could not do this while.
I think the problem is in Windows or in BIOS, or is it due to the fact that there is another version of the motherboard?

I installed Windows 7 64 bit Bluetooth works. The touchpad does not work ... does not work with Windows installation and does not constitute key for the touchpad that are on the motherboard ... I have installed the driver MSI SUPPORT still nothing ...
I also tried connectors that go to moterboard
This is a motherboard: 63-0100-000001-00101111-102010-Chipset $ 0AAAA000_MSI GE620 / GE620DX / FX620DX / FX623 E16G5IMS VER: 1.0r 10/24/2012
PHOTO BIOS: http://www.photobox.co.uk/my/photo/full?photo_id=20705038832
When installing FIRMWARE I progressed through DOS and USB key after opening the "eCall" they wrote: "Target board FileName is different!"
SCREEN: http://www.photobox.co.uk/my/photo/full?photo_id=20705087535
I read somewhere that you just rename the file "16G5EMS1.416" but then I have written of the file is corrupted ...
And I have a plate "E16G5IMS" no "E16G5EMS1" ...

More text not working after using bluetooth map profile with bmw

Hello,
I am using my BB9360 in my BMW. Everything is working fine, emails, contacts, schedulke and tasks are displayed. But after leaving the car my BB is not able to complete an email (more text). After doing an restart (BB) the "more text" menu is working again. Disabling the email accounts in the bluetooth map options is a work around.
I swapped the hardware witth no effect.
I am running OS 7.1 Paket 1133 v7.1.0.336
Any suggestions or ist it a known bug?
Walter

I have exactly the same issue with BMW iDrive on a Dec 2011 M3 and Bold 9900 using the snap-in adaptor and bluetooth - but thanks for the workaround, was really doing my nut not being able to download more!
Would prefer a bug fix though of course - am up to date on latest versions for the 9900 on Vodafone UK, but I have an outstanding update on the iDrive which I will do and let you know the result.

Kitkat update messed my phone up. wifi not working right and bluetooth will not work. Says it is paired but won't work. Really angry about loosing calendar

How can I get bluetoth working again and can I go back to old jelly bean version?

Have you tried resetting network settings in settings, general, reset, reset network settings.
Complete that and from there try and go into settings after it restarts and see if you can manually connect to the network that you wanted.

HT4623 Map not working man and can't connect to istore

**** maps

I would disagree to it.
iPhones sold in Japan are locked to carriers. Apple does not sell unlocked and contract free iPhones in Japan.

Why does my mac keyboard not work properly and is to do with the extra RAM?

Like someone else who has posted on this forum I have a problem with my Apple Pro Keyboard (usb, white, english) The keyboard has developed a fault which has resulted in the tab, caps lock and some other keys near them refusing to work. The caps lock light illuminates at startup but thats about it.
I've run various checks, reset my logic board, unplugged all the cables I can and still nothing. I recently installed two 512mb memory things boosting the machine's memory to 1.5gb. I have since done a full zero install (which was after the fault occured) but the problem persisted.
Is the memory the cause of this issue or is it time to get a new keyboard? I tried to run the apple hardware cd that came with the machine but it refuses to show up on the desktop and I cannot boot from it.
Any help would be very VERY much appreciated.
Also...is there any way of contacting apple with this? The contact us section pretty much just points back to the support site which doesnt have a solution.

nope that doesnt seem to be it. The caps lock light comes on at startup..so it seems it has the capability to work.
the keys which dont work seem to be:
caps
tab
escape
the squiggly thing next to left shift
and the key next to one
thanks for the suggestion though

Playback Not Working Choppy and Get Spin Wheel With Every Action

SOMEBODY PLEASE HELP ME!!!!
I have a MacBook Pro Running on Snow Leopard 10.6.5
Processor 2.4Hhz Core 2 Duo
4GB Ram
External Drive 1Tb-Brand New Files on it.
File Type Imported: .mov
When ever I try to playback it gets choppy, and Spin Wheel comes.
Whenever I click on anything im noticing the spin wheel appear.
I have been looking at various forums,,,trying everything.
Does anybody have the trick to get this thing to playback the clip smooth....
I used Final Cut Express on my MacBook, and I never had this problem ever.
Just upgraded to the MacBook Pro, and Final Cut Pro 7,,,and all types of issues.
Please is the answer out there?

jerseyjoey wrote:
H.264
1280X720
24FPS
44.1 Aud Rate
So what do I have to do from here?
I suck when it comes to technical if you can walk me through it.
Thanks
Joey
You'll need to transcode teh H.264 to a more stable and useful editing codec. It's in the manuals and we see several H.264 questions every day around here so it's pretty easy to research.
jerseyjoey wrote:
I used Final Cut Express on my MacBook, and I never had this problem ever.
Just upgraded to the MacBook Pro, and Final Cut Pro 7,,,and all types of issues.
<
I do not you were using H.264 on your your previous rig. Did you get yourself a new origination camera when you got your new Mac?
bogiesan

Not accepting SN and won't connect with chat online

Really discouraged:
I bought a new computer in April and when I tried to register it wouldn't accept the old serial no. I phoned and after some time, the "tech" informed me that in order to get re-installed I'd have to purchase a new code (or I think he somehow activated me) and it cost me around $200. that was April 27th and I got an email verifying. The C drive had to be replaced as it was bad so another complete re-install and now I'm trying to reach a tech again but in this case when I hit the chat button, nothing happens.
Any suggestions?
TIA

Call support by phone.
Mylenium

I have an iphone 4, i connect it to my laptop using the usb and then when connecting to itunes it says my phone is not up to date with itunes yet i cannot find an update 11.1 for my phones itunes? someone please help me.. kind regards

i have an iphone 4, i connect it to my laptop using the usb and then when connecting to itunes it says my phone is not up to date with itunes yet i cannot find an update 11.1 for my phones itunes? someone please help me.. kind regards

Itunes 11.1 is for your computer, not your iphone
It is required in order to sync with ios 7.

HT2693 I purchased Huawei Dongle and trying to connect with my NEW MacBook Pro (OS- Mountain Lion) USB port 3.0 but unfortunately it does not support. When I plugged in my the power is flowing in dongle due green light blinking twice in every 3 sec but no

Hi,
I purchased Huawei Dongle and trying to connect with my new MacBook Pro (OS- Mountain Lion) USB port 3.0 but unfortunately it does not support.
When I plugged in my macbook the power is flowing in dongle due green light blinking twice in every 3 sec but no connection found or diver shown.
Please let me know how I have to use it. I got some suggestion for USB hub 2.0 but It does not make any sense and driver installation.
So please suggest proper direction to use it and provide link to install any driver.
Thanks
Tauheed Ahmad

Yes Clinton I did same, but they were (Huawei customer support) surprised about this problem, They behave like they have no idea about USB 2.0 and 3.0 knowledge. They handsUp that reason I posted my problem in this forum.
So is there any better solution to use any mediator between these USB version handling, Please let me know.
Thanks
Tauheed

Difficulty syncing and sharing 3G/GPRS connection with NokiaN75 post 10.5.2

Prior to 10.5.2 (Feb. '08) I was easily able to use isync and share my Nokia's 3G/GPRS connection with the MacBook Pro. Whenever I needed to access the Internet or check my email, I could easily and simply establish the connection with the phone via Bluetooth and use the phone's access to the Internet. While not blazing fast, it was quicker than dial up and worked well when traveling and when you didn't want to pay $12.95 for 24 hour access...
Since 10.5.2 I believe, I have had difficulty syncing - I get error messages saying that the synchronization failed. I can no longer connect and share the 3G connection, - an error message about PPP...Can anyone suggest a work around or perhaps Apple's engineering can put in a fix in 10.5.3??? Downloading the isync plug in from Nokia had no benefit...Thank you in advance...

Actually I was answering Paul who does have an iMac but it doesn't matter one way or the other - the same answer applies. Odd that you have the same settings in security and sharing but it doesn't work in one direction. Are you sure you are using the right password? Have you attempted sharing with a different account on that computer?

I have installed the agent 10 or 15 times and one installation hasfailed, no error appeared during the installation but I am havinginconsistent issues with my ethernet card not working here and there. Werebooted and can log into Novell client but th

I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
Andy

If you are searching the registry, check for the "Senforce" string. It should be at HKLM\Software\Senforce
Try running the install program for the ZSC with the following command line:
setup.exe /V"STUNINSTALL=1"
If you've specified an uninstall password, try this one instead:
setup.exe /V"STUNINSTALL=1 STUIP=password"" (please note the double quote at the end)
Let me know if that helped you.
Daniel
>>>
From: Andy_DeWees<[email protected] du>
To:novell.support.zenworks.endpoint-security-management
Date: 2/5/2009 12:52 PM
Subject: I have installed the agent 10 or 15 times and one installation hasfailed, no error appeared during the installation but I am havinginconsistent issues with my ethernet card not working here and there. Werebooted and can log into Novell client but the login prompt did not appearfor ESM client or the icon was not in the systray. Everything seems towork, besides at times (a couple times today) it terminates his ethernetcard/connection. I would re-image his computer but he has severalapplications and
I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
Andy

How do I scan and email documents on my canon mx870? I have a MAC OS X 10.7.5 and it is connected with a usb cable to the printer. Thank you so much!

How do I scan and email documents on my canon mx870? I have a MAC OS X 10.7.5 and it is connected with a usb cable to the printer. Thank you so much!

Hi, I have 10.6.8 and an HP printer so it may be slightly different but I'll give it my best shot:
Go to System Preferences.
Click on "Print & Fax"
Near the top of that page you should see "Print" and "Scan" options. Click "Scan"
A button appears that says "open scanner"
The settings are different between the different scanner models so I'm not sure what the next window will look like, but it should be pretty straightforward from there. It will scan to a JPEG image which you can attach to an email. I hope that helps! Let me know if there's anything ense I can help with.

I am using iphone 3gs since last 4 days. Till yesterday night it was working fine and i have connected this phone for charging . Morning there was apple logo in the screen and every 1mte (approx) it is blinking. I could not restart the phone.Plz help

I am using iphone 3gs since last 4 days. Till yesterday night it was working fine and i have connected this phone for charging . Morning there was apple logo in the screen and every 1mte (approx) it is blinking. I could not restart the phone.Plz help . I have tried to reset even by pressing sleep and home button but it could not help. Please suggest. Still i have connected for charging .

Sounds like you have corrupt backup data, if this occurs from one phone to another. Try restoring the phone as a new device, without a backup. Try using for a day before installing any other apps, etc. See if that improves the battery life. Then try syncing back applications a couple at a time. Something seems to be locking in the processor which is draining the battery.
Do you live in an area where there are Apple Stores? If so, try making an appointment with the Genius Bar to have the device checked out.

Not working USB and Bluetooth GPRS connection with LG KS360 Tribe

Similar Messages

Maybe you are looking for