Nothing Boots on my Mac Pro 1,1 - Boot Drive, Installation Disc, Recovery Partition, etc.

I tested the boot drive on another Mac and boots just fine.
Situation:
On my Mac Pro, about 2 weeks ago I upgraded iTunes and everything worked just fine, used the computer on mulitiple occasions with no problems, power ups, etc. The last time I powered the computer on, my usual desktop image loaded but then frozed. I did a hard restarted by powering the computer off and restarted. But this time at the boot process the gray apple logo screen with the rotating gear came up as usual but then went to the white screen. I performed mutiple restarts, sometimes the blue screen came up. I restarted in safe mode and booted just fine. This may be a quick workaround but I can't do much in safe mode. I've done all of the troubleshooting I can do/find on the net. Zap pram, reset SMC, reinstall OS X Lion via USB(Does Not Boot at all), cloned another boot drive, reinstall OS X Lion on the boot drive via another Mac, etc. Any last suggestion before ditching computer?

If you can boot up in Safe Mode, take a look at
About this Mac > ( More Info ) > Memory
see if all modules are present, at their expected sizes, and have a Status of "OK". Anything else has likely failed.
Use this article to read out the stored kernel panic logs, and try to cut&paste them here for analysis, or take them to the genius bar.
Mac OS X: How to log a kernel panic

Similar Messages

I have a Mac Pro with four hard drives. I currently have Lion installed on one hard drive. I want to have the option to boot from either Lion or Snow Leopard. How can I do this?

I have a Mac Pro with four hard drives. I currently have Lion installed on one hard drive. I want to have the option to boot from either Lion or Snow Leopard. How can I do this?

It's best to install Snow Leopard on one of the three remain drives without an Operating System.
You can then install the applications you need from the original media. Create a User Account using Setup Assistant.
Do you want to migrate User Accounts from the OSX LIon boot drive, or are you keeping the User Accounts separate?
Dual-booting just requires holding the option key during startup and selecting either Lion or Snow Leopard.

I currently run Mac Pro with three hard drives. Can I dual boot or even triple boot with Snow Leaopard on one drive and Mountain Lion or Lion on others?

I currently run Mac Pro with three hard drives. Can I dual boot or even triple boot with Snow Leopard on one drive and Mountain Lion or Lion on others?
I need to keep Snow Leopard so that I can run some old softward.

If you are careful you can put at least two on one drive, having Recovery from Lion and Mountain Lion on their own drives though.
CCC can clone Lion Recovery - great for moving or backup.

I have a new Mac Pro. I want to use my old Mac Pro as a storage drive for photos and old documents, linked to my new Mac Pro. How do I set up the old computer?

I have a new Mac Pro. I want to use my old Mac Pro as a storage drive for photos and old documents, linked to my new Mac Pro. How do I set up the old computer? Both computers have OS X10.9.3. Currently they are connected by a Firewire 800 cable.

You certainly could keep the old Mac Pro in Firewire mode (hold down the T key on its keyboard as you boot) to show its drives on the new MP. This is basically as fast as putting the drives into a Firewire enclosure.
Or you could boot it normally and share its files over the network using the Sharing panel of System Preferences. If you turn on both File and Screen Sharing, you don't even need to have a monitor attached - you can do all administration using screen sharing. However, this method requires that you open all files over the network, which will be slower than the direct-connect method above, and may also not work with all applications.
Matt

Mac Pro will not restart after installation of Lion. Help!

Mac Pro will not restart after installation of Lion. Help

Reinstalling Lion Without the Installer
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alterhatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.

Is it possible to use one of the mac pro's internal hard drives as a external drive that can be accessed by a macbook etc?

is it possible to use one of the mac pro's internal hard drives as a external drive that can be accessed by a macbook etc?

Only if you move it to an external enclosure and let them both access it through a file server.

HT4818 why doesnt the new macbook pro come with the windows installation disc?

why doesnt the new macbook pro come with the windows installation disc?

Because it is a Microsoft product. it must be purchased separately.

Mac Pro 2.66 internal drives in a Mac Pro 64bit i7?

Is it possible to just unmount my internal drives from my workhorse Mac Pro 2.66 Dual Core Intel Xeon tower and mount in my new 8C Xeon 2X2.4g 64bit tower?
Thanks in advance!

Director wrote:
Is it possible to just unmount my internal drives from my workhorse Mac Pro 2.66 Dual Core Intel Xeon tower and mount in my new 8C Xeon 2X2.4g 64bit tower?
Thanks in advance!
It's not clear if your workhorse is an original, or at least early Mac Pro and you new Mac Pro is the 2010 version, but if so, be aware that the drive sleds the internal drives are in are not the same. I don't know what would happen if you tried that swap but I doubt it'd be good for the new Mac Pro.
The drive itself could be transferred from the old sled to the new sled and it would fit but, if the new Mac Pro is, indeed, a 2010, it won't boot because 10.6.4 is the minimum OS needed. You could, however, use it for Setup Assistant or Migration Assistant purposes.

Why can't my Mac Pro use my hard drive(s)?

Ok, so I'm using a 2008 mac pro (some specifics are listed at the bottom) and I'm having trouble with my hard drive(s). The hard drive I've been using is full, and sometimes the System Information will show that is full of Audio, Movies, Photos, Apps, Backups or it's just chuck full of "Other."
But the problem is that my computer stopped using one of my hard drives a while back. It was called "Bay 5." I've opened up the computer to look at the hard drives and I actually have three. Ever since I lost Bay 5, I lost my Adobe Creative Suite and I've gotten a notification that says "The disk you inserted was not readable by this computer." But the drives are the same type as the Macintosh HD, only with 500 GB each. I've clicked "Initialize" on this notification (sorry, I tried to take screen shots but suddenly my computer says "You don't have permission to save files in the location where screen shots are stored") and it pulls up the disc utility and has a drive called "Media," (but only half the time). Bay 5 is not there and neither is the other drive that's there.
Wow, that screen shot thing is new. Maybe you guys could help me with that problem, too.
I'm lost. I've looked at 15 min. long youtube videos but none of them have helped. I just want to be able to use those hard drives. I've tried holding the D key at start-up so that the computer can do the Hardware check (or whatever it's called) but it just pulls up a flashing folder with a question mark.
I'd really appreciate some help.
Processor: 2 x 2.66 GHz Dual-Core Intel Xeon
Memory: 4 GB 667 MHz DDR2 FB-DIMM
Software: Mac OS X Lion 10.7.5 (11G63)

Buy Carbon Copy Cloner and some new drives. Make sure you have two backup sets and are using TimeMachine as well.
Reset SMC
You have a 1,1 2006 model. It is low on memory, which is cheap at $25 2x2GB now on Amazon
Consider that drives fail and you may have some drives that are more than 4 years old.
If you want, and have the money, consider investing in Disk Warrior 4.4 or 5.0
Data Rescue 4 has a demo and would try to find files, would need a recovery drive volume of course also.
Invest in an SSD for system boot drive, $119 / 250GB, and use a WD Black 1-2TB for data $120, another for TimeMachine.
Adobe CS needs more memory that you have.
AHT is not going to help and is on the OEM DVD with 10.4.x that it came with but what you need is boot from another drive or recovery mode and use Disk Utility (and or Disk Warrior). Single User Mode and 'fsck" is also useful as would Safe Boot. But you need a working copy (clone) backup too.
I like to have a nice small "Emergency" boot drive with just the minimum for system maintenance, 20GB is fine, some users create a USB flash drive but FireWire or USB2 work well. Or just designate and create a small 20GB volume on any of your other drives.

How best to setup a Mac Pro with two hard drives for 1st hard drive or OS failure?

My first Apple, a Mac Pro, is to arrive on Monday (1/7). I will be putting Win7 on Bootcamp and installing Parrallels. It will have two 1T hard drives.   I would appreciate
any advice on how best to set it up for best recovery in case of a hard drive or OS crash.   You can tell I have experience with Windows.    It looks like my best choices are
either disk cloning software or just installing OS X from the recovery disk on the second drive.   Apple says it is legal to do another installation.   I know the disk cloning will not work on the bootcamp partition which I plan to use for the Parallels program. Can OS X have an option to boot from two differnet disks and OS installs?
What I am really wanting to do in the event of a crash, is to just boot up on the other disk and keep working.     I try to keep data on a separate partition with backups so
that a disk or OS crash doesn't cause any data loss.

I do not use windows.
However on my Mac Pro for cloning/backups/bootable backups i use Carbon Copy Cloner.
It has an ability to clone entire disk (unless specified differently) so I can boot from another disk or restore back if I want to.

Bootcamp - Windows 8.1 - Mac Pro (Late 2013) -- ATI Driver Crash

Hi All,
I have a open case with Apple as well on this but i can not seem to locate any information on this issue on the web at all.
Case: 601052633
Basically, we received a new Late 2013 Mac Pro, and out of the box proceeded to install bootcamp and windows 8.1.
After the install and the bootcamp drivers are installed the screen starts to display lines and the ATi drivers eventually crash.
If we uninstall the ATI drivers the screen is returned to normal and windows uses the generic drivers, however the graphics performance is degraded.
If we install the latest ATI drivers (downloaded directly from the ATI webpage) the display issues reoccur.
If left to run its path the screen becomes unreadble and eventually the system bluescreens.
To recap all the things I have done:
Straight out of the box we started the boot camp install. We use the latest Windows 8.1 Media.
Once the process is completed the PC reboots as normal and we install windows on the “BOOTCAMP” partition.
Windows installs without issue and when the bootcamp drivers window pop’s up it starts its install. At the “Chipset” drivers install the window starts to flicker, this appears to be normal but afterwards the screen shows “lines” on it. (these lines can be seen on image below)
Once windows is booted the lines remain and progressively gets worse. Image below shows the ATI Criver crash and the blue screen. This takes 2-5 seconds. And depends on how much you move on the screen.
Screen capture (shown Below) shows the issues, even with screen capture the issue is recorded.
If we uninstall the ATI display drivers the issue disappears.
Process of tests:
Install Bootcamp windows 8.1 on Mac pro 2013 out of the box – Issue recorded
Remove Bootcamp and update firmware on Mac.
Install Bootcamp windows 8.1 on Mac Pro 2013 – Same issue.
Updated ATI Drivers using ATI drivers off ATI website – Same issue
Uninstalled ATI Drivers – 2 Generic Microsoft video cards detected – issue removed but video performance degraded.
Updated Bootcamp Drivers – ATI drivers reinstalled – Issue returned
Removed bootcamp, restored system to factory settings via web install.
Installed Bootcamp windows 8 on Mac Pro 2013 – Same issues
Removed bootcamp restored System to default
Tried installing windows 7 – not supported
Installed Windows 8.1 and ran screen captures and diagnostics.
We have also tried using different display ports, Different display adaptors, Different monitors.
Mac OS is not affected.
Note Mac is “out of the box”, Windows is a next next next install. No changes or software is installed.
Any support would be appreciated.
Cheers
Steffen.
It Manager.

I had this exact same issue and had been hunting it down since i first received my Mac Pro back in May 2014. I researched the problem all over the place but I have no idea why i did not find this post, or in fact why Apple techs did not find this post either.
Bottom line: In my case I have pretty much proved this was a problem with the AMD FirePro D300 video card/s. They basically can't cope with Windows graphics needs.
I have a new Mac with D500 cards, and now the problem is almost completely gone. I can recreate if i run certain situations and a screen saver. Upon refresh, there is a chance the card will crash, but showing a slightly different outcome.
Having read the prior posts, the D700 may also have the same issue??
Longer story and background: I am not exactly an expert, but i did try many different things and probably spent in excess of 200 hours onto tech support and installing, reinstalling, trying different monitors, trying different software. Eventually i was so frustrated and in tears with this issue.
The major problem over all this time was the constant response from Apple that this was not an Apple issue since the Mac OS was not showing any issues.
I was at the time a new Mac convert, my brother had purchased the 'awesome' machine for me as a birthday gift, with the goal that we could play a specific game together. My disappointment in Apples inability to recognize or even attempt to recognize that this was related to the hardware in the Mac itself was constant and ongoing.
My final visit to the Apple store to again visit the 'Genius' bar came up yet again with the most senior tech in the store telling me that there were no problems identified with the hardware and that this was not their issue. Totally frustrating. I was rather hoping, in the good tradition of true geeks, that this would have been a challenge to hunt down. I was pretty sure they trusted me that this was not a standard Windows issue, and thus was hoping they would switch out individual pieces of components (video cards being my first choice) to see if that the problem repeated. Nope, didn't want to do it.
My response was to threaten with legal action - not something i enjoyed doing, plus that i would NEVER buy an Apple product again. Since I was a new business client, this may have had an impact.
This wonderful Manager at the store agreed that he wanted to take the hardware out of the equation and see if I still had the issue. So he, amazingly, agreed to refund in full for the machine and I could order a new one.
As i was convinced this was hardware related, since I had the Quad core, D300's, 12 gig machine and my brother had the top of the range six processor, D500s, 16gig memory machine which did NOT have this issue, running identical software, when i reordered the Mac Pro, I bumped it up to the D500s (still Quad core) and 16gig of memory (also had the 1TB drive partitioned 40/60 in bootcamps favor).
I tentatively installed windows after a couple of days of normal Apple usage (software updates included).
I then hammered the system with the same software and installs.
Its been up and running for perhaps 2-3 weeks now, and I have not seen the issue at all, other then when i had screen saver running and 4 instances of the game running (Everquest for those of you who are interested - but the software is almost irrelevant, since i have had this issue using internet explorer or Chrome).
So.. I urge Apple to review this issue with the D300s and either remove them from the configuration options or resolve the issue. One of the powerful selling things for this wonderful machine is its ability to run Windows in native mode. I like it because I also want to get into App Development, so the dual option boot option is just what i wanted.
Responding to us poor Windows installers with 'not my problem' simply isn't good enough and should never have been something i had heard.
All good now, I am happy with the end result, but I would like Apple to recognize this IS AN ISSUE THEY NEED TO ADDRESS.
I apologize if my technical knowledge is not a strong as it might need to be in relaying this information to you guys, but hopefully it all makes sense.
Paul

Is it possible to upgrade the Mac Pro with SCSI/SAS drives?

Hi guys I am considering to move on to a Mac Pro from my old PC.
The Mac Pro enclosure is quite unique in its hard drive holders as no cables are used and all drives are connected with a plugin mechanism.
So I am curious if that will allow me to upgrade to a SCSI/SAS storage system which requires cable connections between drives and the SCSI/SAS card on the PCI-E slot. I dont know if this will be possible with the Mac Pro enclosure.
Has anyone tried to do this？
Btw is there any Ultra320 or SAS(preferably) interface card available for Mac OS X?

The connectors for SATA drives can be used with SAS drives. However, the controller needs to be SAS compatible. I have never installed a SAS drive in the Mac Pro bay to see what happens. If some one has a SAS drive and wants to try this I would be interested in the results.
My guess is that the Mac Pro would not see the drive.
Areca sells the Mac Pro PCIe bootable ARC-1680 SAS controller in several configurations. This controller allows the user to utilize SAS or SATA hard drives connected to the card. The ARC-1680x comes with two external mini SAS connectors that can support eight direct connect hard drives or up to 128 devices (in theory) when used with SAS expanders.
The ARC-1680LP has one internal mini SAS port and one external mini SAS port. I looked at the Mac Pro internal SATA connectors and they can unscrew from the frame but there is only about 1/2" of clearance in that area of the case. In addition, I would want the hot swap bays to still operate and I did not see an easy way to patch into the existing SATA connectors. It would be nice if the Mac Pro factory connectors used snap on SATA connector on the back of the backplane so that users could interface the 4 SATA bays with an internal PCie controller. However, its hard wired in the existing configuration. With the new Mac Pro PCIe RAID 5 card on the market there must be alternative connectors that allow this type of installation to work properly.
Based on the ease at which the Areca SAS controller can be added as an external using the ARC-1680x I went with that option. I am using it with eight direct connect SATA hard drives now. I plan to expand the storage by adding a SAS expander in the form of a hub or an enclosure with SAS capabilities. I have been looking at a 16 bay SAS enclosure but I am not sure how loud it will be
Details on the ARC-1680 can be found here:
http://www.areca.com.tw/products/pcietosas1680series.htm
Its very cool to have SAS or SATA capability along with a bootable card that can support tons of hard drives and RAID levels 0, 1,1E, 3, 5, 6, 10, 30, 50, 60 or JBOD . I booted the Mac Pro with a 2TB Mac OS X 10.4.10 RAID 6 volume and ran Xbench. It shows a 400MB/sec. hard drive setup and raises the overall Xbench score substantially.
While I doubt I will boot the Mac Pro from the RAID 6 volume much, it is very cool that that function is available. This is the only PCIe host adapter I have found with boot capabilities besides Apples new $999 4 port SATA internal card. SAS has lots of expansion capabilities. Users that want pretty much unlimited hard drive connectivity will enjoy the new ARC-1680x.
Have fun!

Mac Pro & Older serial ATA drive

I added a second 160 gig ATA drive (Capacity:149.05 GB Model: ST3160023AS
Revision:3.05) two and a half years ago to my 1.8 ghz Power Mac G5. I just bought a Mac Pro. Can I use my older drive in one of its bays? Do I need to do anything special?

If it is SATA then all you should need to do is insert it into a drive sled and plug it in. If you want to boot from it then you will need to erase it and change the partition map scheme in Disk Utility.

My Mac Pro will read thumb-drive but not CF card reader

Can someone help me resolve this problem?
I just erased everything off my Mac Pro and reconfigured everything (as new). I installed all my programs, primarily Aperture3 and Photoshop CS5
(using Leopard).
I had NO problem uploaded some photos into Aperture3 from a thumb drive using the USB port, BUT,
when I tried to upload photos from my card reader the MacPro does not recognize the card reader using the same USB port.
I figured the problem was a bad card reader, so I tested it on my PC and it recognized the card reader and uploaded all the photos.
Also, the card reader's green light turns on when attached to the MacPro, as if it is working and connected but it does not register in Finder or desktop to indicate that the card reader is installed.
I even tried to upload directly from my Canon 7D and it also did NOT recognize the camera.
Why would the MacPro recognize the thumb drive on the same USB port and not the card reader or the camera?
Please help!

Try power down and doing an smc reset:
Intel-based Macs: Resetting the System Management Controller (SMC)

I have a Mac Pro tower with two internal Hard Discs, each one 2TB. I purchased a 3TB Time Capsule. But it does not allow me to back up because it says there is not enough back up space available. Between the two HDs there are 3.3TBs. Can I daisy chain TC?

I have a Mac Pro tower (OSX version 10.6.3) with two internal Hard Drives, each one 2TB.
I purchased a 3TB Time Capsule. But cannot back up because it tells me there is not enough space.
I have more than 3Tbs to store to the new TC.
Can I daisy chain two TCs to store the 4TBs?
How can I back up only the internal HD that is already full, without backing up the other one?
How can I do back up using Time Machine to back up the 3.5Tbs?
Do I need to purchase another external HD (that is not TC) to be able to back up all of my photos?

Can I daisy chain two TCs to store the 4TBs?
No, you cannot link to produce a single large partition.
But you can have two separate backup jobs.. and use each partition. That is hard on TM but you can easily get a different backup software for it.
How can I back up only the internal HD that is already full, without backing up the other one?
In TM you do a different setup and exclude the other drive.
But it is better to use an alternative software IMHO.
How can I do back up using Time Machine to back up the 3.5Tbs?
You would need to use a network drive of more than 4TB .. it would also take forever. This is just wrong way to do it. Although you can buy a NAS that will work with Time Machine and load it with disks 16TB is possible.. if you can get a second mortgage.. the fragile nature of TM on 3rd party devices.. would leave me in cold sweat if anything went wrong.
TM is excellent at keeping incremental backups of files that keep changing.. as such you should use TM to backup your OS disk and main user directory.. exclude all files and directories that never change. Back them up separately.
Do I need to purchase another external HD (that is not TC) to be able to back up all of my photos?
Yes, that is a much better idea. You want to store photos safely and you want to store them in multiple places. If you have multiple TB of photos, dedicate a couple of disks to the backup. ie have at least two copies.. not in backup format.. in straight copy format if possible.. so you can keep one of the disks offsite.
I would be using your MacPro internal disk access, to place the disk onto sata bus and do the copy disk to disk direct. Or even buy esata card.. or sata to esata converter cable so you can use esata box. That will beat any other transfer speed except thunderbolt for which you would need third mortgage. (The MORT in mortgage is significant).
The great jurist Sir Edward Coke, who lived from 1552 to 1634, has explained why the term mortgage comes from the Old French words mort, "dead," and gage, "pledge." It seemed to him that it had to do with the doubtfulness of whether or not the mortgagor will pay the debt.

Nothing Boots on my Mac Pro 1,1 - Boot Drive, Installation Disc, Recovery Partition, etc.

Similar Messages

Maybe you are looking for