Nothing displayed on TV through HDMI.

I have an Acer 4820T with Intel HD 3000 graphics and am trying to use a Sharp LC-37GA8E as a second display. It works in Windows 7 without problems but not in Arch using arandr/xrandr. The TV will change resolution as you try different settings but the screen is blank. Arandr/xrandr does work perfectly with an LG M2262D through HDMI.
xrandr -q
Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192
LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 309mm x 174mm
1366x768 60.0*+
1024x768 60.0
800x600 60.3 56.2
640x480 59.9
VGA1 disconnected (normal left inverted right x axis y axis)
HDMI1 connected (normal left inverted right x axis y axis)
1920x1080 25.0 + 30.0
1280x720 60.0 50.0
1440x576 25.0
1440x480 30.0
1024x576 60.0
800x600 60.3 56.2
720x576 50.0
848x480 60.0
720x480 59.9
640x480 59.9 59.9
DP1 disconnected (normal left inverted right x axis y axis)
xrandr --verbose
Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192
LVDS1 connected 1366x768+0+0 (0x45) normal (normal left inverted right x axis y axis) 309mm x 174mm
Identifier: 0x41
Timestamp: 259803492
Subpixel: horizontal rgb
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff000daf571400000000
03140103801f11780abac59457549127
20505400000001010101010101010101
010101010101781d56c2500026301f41
4c0035ae10000018000000fe004e3134
3042362d4c32340a2020000000fe0043
4d4f0a202020202020202020000000fe
004e31343042362d4c32340a20200033
BACKLIGHT: 9 (0x00000009) range: (0,9)
Backlight: 9 (0x00000009) range: (0,9)
scaling mode: Full aspect
supported: None Full Center Full aspect
1366x768 (0x45) 75.4MHz -HSync -VSync *current +preferred
h: width 1366 start 1397 end 1462 total 1560 skew 0 clock 48.4KHz
v: height 768 start 772 end 784 total 806 clock 60.0Hz
1024x768 (0x46) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
800x600 (0x47) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
800x600 (0x48) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz
v: height 600 start 601 end 603 total 625 clock 56.2Hz
640x480 (0x49) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
VGA1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x42
Timestamp: 259803492
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
HDMI1 connected (normal left inverted right x axis y axis)
Identifier: 0x43
Timestamp: 259803492
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff004d10c70f01010101
0010010380522e782a1bbea25534b326
144a5200000001010101010101010101
010101010101011d80d0721c1620102c
258034cd3100009e8c0ad08a20e02d10
103e960034cd31000018000000fc0053
484152502048444d490a2020000000fd
00313d0f2e08000a20202020202001bd
020321714d9405130411120203151606
0701230907078301000066030c001000
808c0ad090204031200c40550034cd31
000018011d8018711c1620582c250034
cd3100009e011d00bc52d01e20b82855
4034cd3100001e011d007251d01e206e
28550034cd3100001e00000000000000
0000000000000000000000000000009b
Broadcast RGB: Full
supported: Full Limited 16:2
audio: auto
supported: force-dvi off auto on
1920x1080 (0x143) 74.2MHz +HSync +VSync Interlace +preferred
h: width 1920 start 2448 end 2492 total 2640 skew 0 clock 28.1KHz
v: height 1080 start 1084 end 1094 total 1125 clock 25.0Hz
1920x1080 (0x146) 74.2MHz +HSync +VSync Interlace
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 33.8KHz
v: height 1080 start 1084 end 1094 total 1125 clock 30.0Hz
1280x720 (0x15b) 74.2MHz +HSync +VSync
h: width 1280 start 1390 end 1430 total 1650 skew 0 clock 45.0KHz
v: height 720 start 725 end 730 total 750 clock 60.0Hz
1280x720 (0x15a) 74.2MHz +HSync +VSync
h: width 1280 start 1720 end 1760 total 1980 skew 0 clock 37.5KHz
v: height 720 start 725 end 730 total 750 clock 50.0Hz
1440x576 (0x15d) 27.0MHz -HSync -VSync Interlace
h: width 1440 start 1464 end 1590 total 1728 skew 0 clock 15.6KHz
v: height 576 start 580 end 586 total 625 clock 25.0Hz
1440x480 (0x160) 27.0MHz -HSync -VSync Interlace
h: width 1440 start 1478 end 1602 total 1716 skew 0 clock 15.7KHz
v: height 480 start 488 end 494 total 525 clock 30.0Hz
1024x576 (0x161) 47.0MHz -HSync +VSync
h: width 1024 start 1064 end 1168 total 1312 skew 0 clock 35.8KHz
v: height 576 start 577 end 580 total 597 clock 60.0Hz
800x600 (0x47) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
800x600 (0x48) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz
v: height 600 start 601 end 603 total 625 clock 56.2Hz
720x576 (0x165) 27.0MHz -HSync -VSync
h: width 720 start 732 end 796 total 864 skew 0 clock 31.2KHz
v: height 576 start 581 end 586 total 625 clock 50.0Hz
848x480 (0x166) 33.8MHz +HSync +VSync
h: width 848 start 864 end 976 total 1088 skew 0 clock 31.0KHz
v: height 480 start 486 end 494 total 517 clock 60.0Hz
720x480 (0x167) 27.0MHz -HSync -VSync
h: width 720 start 736 end 798 total 858 skew 0 clock 31.5KHz
v: height 480 start 489 end 495 total 525 clock 59.9Hz
640x480 (0x49) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
640x480 (0xa15) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 489 end 492 total 525 clock 59.9Hz
DP1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x44
Timestamp: 259803492
Subpixel: unknown
Clones:
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
Broadcast RGB: Full
supported: Full Limited 16:2
audio: auto
supported: force-dvi off auto on

https://wiki.archlinux.org/index.php/KM … odesetting

Similar Messages

  • Imac HDMI doesn't display to TV through HDMI

    imac HDMI doesn't display to TV through HDMI switch

    hdmi switches are notorious for not working with most computers and appletv's and well most things with hdmi ports really

  • Toshiba Regza does not display PC connected through HDMI

    I live in a flatshare in which there is a Toshiba Regza in the living room.
    This television is connected to a Virgin Media V Box through an Xbox HDMI cable.
    I tried using the same cable to connect the tv to my laptop, which has a HDMI port, but nothing shows up on the screem.
    I checked in yhe Nvidia control panel and on the computer's screen settings: the Toshiba-TV is successfully recognized, so why I cannot see anything?
    The V Box is usually tuned on the HDMI-1 channel, but all I see there is a blue screen. Same on HDMI-2.
    The PC channel is instead black.
    Can somebody please help and tell me what I am doing wrong?

    What model is the TV?
    - Peter

  • Sony KDL-48W600B will not display 1080p signal through HDMI

    I just bought that sony KDL-48W600B  1080 tv and want to use it as monitor for my pc.. but the tv only shows pc content if I put the resolution to 720p. When I go higher the tv shows black/blank screen. What should I do to get 1080p output on the TV via hdmi?

    make sure the TV is on when you boot the computer. I have had that happen, I am assuming the model supports 1080 mode.

  • Watching your display through HDMI lead

    i have a 13" macbook pro which is 7months old, however when i connect the mini display port adapter to hdmi lead to watch a stream through the television ....the only display showing on the television is the wallpaper??? anyone help please, thanks

    Run System Preferences / Displays and rather then using Extended Desktop check Mirror

  • Bought a TCL Roku TV. Connection with Macbook Pro through HDMI will not show display on TV. Have tried various options with no success. Suggestions/solutions?

    Bought a TCL Roku TV. Connection with Macbook Pro through HDMI will not show display on TV. Have tried various options with no success. Suggestions/solutions?

    You could try updating your apple TV and then restarting it. Bit of a guess.

  • Sound through hdmi to my tv works but not when watching video online like 4OD

    the sound through hdmi to my tv works with music and videos I have downloaded, but not when watching video online like 4OD and youtube.
    How can I get it to work?

    Ok so I happened to figure it out while on the phone to apple support. Even though the guy was very nice, I think I knew more than him! He was explaining very basic resolution principles I played about. I had the second option in displays resolution. All I did was unplug the HDMI cable, click on 'best for display' then plugged the HDMI in and my resolution on the normal monitor changed to the normal blue, then went black momentarily and then changed to a strange resolution but another window appeared that said SONY BRAVIA HDMI at the top! Hey presto! Don't know why it didn't do it yesterday - I probably left the HDMI cable in or something! Oh well. Problem solved!

  • Mac mini will not recognize my hdtv through hdmi to hdmi

    I just bought the new mac mini, got home super excited, hooked it up to my hdtv through hdmi to hdmi and nada.
    I have a Vizio, 42-inch, 50/60 hz, Plasma TV.  It was made in 2006 so there is no DVI port, it only has an RGB port other than the 2 HDMI ports.
    I have tried both HDMI ports.
    I tried turning everything off, unplugging everything waiting 10 seconds, reconnecting everything and turning the mac mini on first, then the tv AND vice versa.
    Nothing.
    My HDMI cable was kind of old so I went out and bought a new one from Belkin.
    Nothing.
    It does look like the TV is recognizing the device because it does not say "No signal", so it seems that the mac mini itself is not recognizing it.
    I just bought this thing, it has not even been setup yet!
    And I do not have another moniter here to hook it up to.
    I tried calling Apple Care, but I called at 7:30 waited for 30 minutes for someone to tell me they were transferring me to tech support, then the phone rang for 10 minutes.  I hung up and called back and they said the office was closed!
    I am a die hard mac user, but I am at my wit's end here.
    I guess my next step is to take it to the genius bar?
    But I wanted to see if anyone out there has any suggestions/ideas?
    (I know there are other discussions out there about this, but nothing I found actually helped my situation.
    Thanks everyone.

    I just got my mac mini as well and I'm having the same problem with my HDTV. Unfortunately I am not at home so I do not have the tv model on hand but it is a Panasonic from 05/06.  I am trying to connect from the HDMI on the mini to the HDMI port on the tv and when it boots up the grey start upscreen shows up on the tv and loads for alittle bit than everything goes black. Any ideas?

  • Toshiba 46TL938: Choppy 3D playback when PC-to-TV through HDMI

    Hello,
    I got a very specific problem and cannot spot exactly where the problem may be. In brief:
    - I got a 3D movie which is played back through VLC but also KMplayer.
    - On my 23" monitor 1080p through HDMI the movie plays pretty well and smooth.
    - On my Toshiba 46" HDTV the playback on 3D lags sometimes, exactly the same when a computer cannot handle the load and lags on video playback.
    -I tried to put the movie on a USB flash and connect it to the TV. Then the playback of the 3D on the TV was really smooth without any lag.
    So facts are the frames work well on a HD 23" monitor (playedback with VLC & KMplayer), but also run smooth on my notebooks monitor.
    Fact is also that the same movie plays smooth from a USB flash connected on the TV.
    I tried with another movie (non 3D) to stream it from my notebook through HDMI on my TV. It worked pretty well without any lag.
    1) So my main question is if the movie is not ok, why does it play back correct through a USB but not through my notebook.
    2) Furthermore if my laptops vga would be unable to handle 1080, i guess the playback would lag also on my 23" monitor which is also 1080.
    I really have no idea if it is the movie , TV, or vga that has the problem.
    Any suggestion would be great.
    Thank you in advance.
    Hardware info:
    TV: Toshiba 46TL938
    Notebook: Fujitsu Amilo xi 2528

    Hi
    I dont think its TV issue.
    First of all using USB flash memory stick, the movie playback is handled by Toshiba media player and secondly the data does not need to be send through an cable.
    Streaming the movie from notebook, you send the signal to the TV via HDMI cable. The 3D movies contains a lot of data and this might affect the playback quality streaming the data from one device to another.
    So if you would notice some interrupts while playback, this might be related to the HDMI cable.
    If your HDMI connection is capable of 1080p and/or your television is capable of refresh rates greater than 50Hz, you will need a Category 2 cable. Conventional HDMI/DVI cable may not work properly with this model. Try also an short cable (1.5-2m)
    You should also check the user manual *page 88.*
    The HDMI inputs on this TV only accept VGA, SVGA, XGA, WXGA, and SXGA signal formats which are
    compliant with VESA as shown in the table _page 88_.
    Since some PCs and HDMI or DVI devices input signals which are different from the resolution and frequency described in the table, the following phenomenon may occur; _incorrect display, false format detection, picture position failure, blur, or judder_.
    In this case, set the monitor output format on your PC, HDMI or DVI device to conform to a signal in the table you would find in user manual.

  • No sound through HDMI alternative solution

    If you are not able to get sound through your TV through HDMI and have tried all the System Preferences/Audio MIDI steps detailed on here in other threads but nothing works, try just shutting down all running apps.
    I had to Force Quit Spotify, Viber, Skype - when I shut down iTunes, the sound from Firefox started coming through the TV. I have since been able to reopen Spotify and play it through the TV too.
    I'm not sure why these apps would interfere with the HDMI sound transmission, perhaps more technically inclined people can answer this but it turned out to be a straightforward solution that I didn't find on here (although maybe I just didn't look hard enough!).

    Is it an occasional problem or is it that you have never had the hdmi audio output working with windows 7 Ultimate?  If it has never worked, is hdmi even listed under playback devices when you right-click the speaker icon in the notification area and click playback devices? 

  • HP Omni 27 - Xbox 360 sound doesn´t play through HDMI

    Product Name and Operating System:
    HP Omni 27 - 1001es - Windows 7 Home Premium
    Description of the problem:
    Hi everybody: I have plugged my Xbox 360 through the HDMI cable to my Omni 27 computer. The image is well seen, but there is no sound from the console available.
    Could anyone help me to fix this problem?
    Thanks in advance.
    PS: I´ve tried different inputs to the computer like a SAT TV receiver through HDMI and both the image and the sound work nicely.

    Hello ipillo,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I understand you connected your XBox 360 to your HP Omni 27-1001es Desktop PC and are getting the video, but not audio. I ran into this myself once on my XBox and here are the steps I used to fix it:
    Step 1. Click on Settings
    Step 2. Click on System
    Step 3. Click on Consol Settings
    Step 4. Click on Display
    Step 5. Click on Display Discovery
    Step 6. Choose Disable
    Step 7. Restart
    Please re-post if you require additional support. Thank you for posting on the HP Forums. Have a great day!
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

  • Screen size to big through hdmi

    Hi Guys,
    I have conected my desktop to my tv through hdmi but the display seems a little largecant really see my icons at the bottom i need to bring the picture in around 10mm all the way round pleasen help.
    Thanks in advance for all and any help peeps

    st_enoch
    Welcome to the HP Community Forum.
    I can tell you what might be wrong -- but I cannot tell you exactly how to fix it on your TV...
    I believe you need to adjust the Aspect Ratio and shove in the sides a bit on the display.
    This is NOT the resolution -- that is probably fine.  Different animal.
    The adjustment is likely done on the monitor itself, that is, with the buttons / settings available on the back / side of the TV - or maybe with the standard TV remote.  Keep in mind, that if you were to use a "remote" to make these adjustments, it would be the standard TV remote and NOT the cable remote that one might use with the cable service.  You want to get into the TV monitor settings.
    I hope that helps.
    Click the Kudos Thumbs-Up to say Thank You!
    And...Click Accept as Solution when my Answer provides a Fix or Workaround!
    I am pleased to provide assistance on behalf of HP. I do not work for HP. 
    Kind Regards,
    Dragon-Fur

  • Sound through HDMI

    I how do I run my sound through hdmi for OS X?
    By windows but usually works on OS X does not work.
    My macbook is A1278 and my monitor is LG 23EA53.
    Please help me.

    Hi EdDySK,
    Thanks for visiting Apple Support Communities.
    See this article for the steps to output video and audio using the Thunderbolt port, Mini DisplayPort, or HDMI port on your Mac:
    OS X Mavericks: Use a television as a display
    http://support.apple.com/kb/PH13801
    Cheers,
    Jeremy

  • Dolby digital through HDMI

    I have a 2012 MacBook Pro with retina display. I'm trying to get Dolby digital through the hdmi port and after comparing some media attached to my receiver the same movie was Dolby digital on my WDTV and using the same cable was stereo connected to my MacBook Pro.
    I'm not sure if its a setting or an atypical apple thing like they did with the digital stereo connection in headphone jack using a mini fiber optic cable (phoslink).
    I suppose if I want to hear Dolby digital out of my Mac,  I wondering if I need a thunderbolt to hdmi to get what I want. Dolby digital through HDMI is an industry standard!

    After talking to three levels of support, I finally was told the new Macbook Pros (with Retina display) are NOT capable of producing Dolby digital through the HDMI port.  They only do digital stereo.
    In order to produce up to 8 channels of Dolby digital surround sound you must use an additional toslink cable, which is a mini fiber optic, found cheap at Monoprice!
    Just for the record, the expensive Thundebolt to HDMI or mini Display port to HDMI only do stereo too.  Not a big deal for most, but upsetting if you're expecting a HDMI to function as it does in any other piece of equiptment!!

  • 5.1 sound in Safari through HDMI?

    Hello all!
    I recently bought a new pro retina 15".
    I connected through HDMI cable to my Denon AVR 1713 as my old laptop used to be.
    What a surprise when starting an oline video on Safari, I couldn't get 5.1 sound in my speakers connected to the denon.
    I tried everything I've found in this forum, configuring MIDI settings for 5.1 system. But nothing seems to work.
    I like to see videos online and via some other programs such VLC
    Is this normal? Some way to overcome this?
    Thanks a lot
    Best Regards

    The sound comes from an editor who is a pro and knows how to deliver 5.1.
    I also have premiere ( 5.5 ) so I guess I can import the film and the audio in there and then export for a convert to DCP.
    Or if I understand you right I can use a CDP processing software like
    http://www.magnamana.com/finaldcp-released/
    and there I import still images and the sound seperate?
    That´s how it works?
    /Mattias

Maybe you are looking for

  • Limiting Time Machine backup Size with WD MyBookLive and 10.8

    I cannot take credit for the any part of this solution; merely for merging and clarifying how the solutions discovered by 2 Apple Support Communities contributors much smarter than I (namely “Pondini” – Florida and  “himynameismarek”) - worked perfec

  • Who can help me

    Bad service of Nokia in China ! Official statistics in China have showed that Nokia has won the first place in mobile phone manufacturers who were complained most by Chinese consumers.  When consumers send their new or expensive mobile phones to the

  • DSC "tag engine" "unable to start the citadel 5 service" "unable to start the service"

    Hi, I don't know why, but I'm not able to start the tag engine anymore. First I thought of a corrupt *.scf- file, but this is not the case. To investigate the problem I wrote a nice program, perhaps it is of interest. And perhaps someone else had the

  • Change of supplier move-in error

    hello everybody, i am executing change of supplier. In the distribution company i have the following error in the WF log: "A move-in is already due on 01.03.2009 for installation XXXXX (contract YYYYYYY)" i checked and prior to the execution of Chang

  • Calling function through RFC

    Hi Colleagues, I need to make a function call from 1 SAP system to another SAP system. Please let me know if I should create a new ABAP RFC connection between the 2 systems. If so please let me know the procedure to create a new ABAP connection. Shou