NSS 326 Mount Volume Please Wait...

I have suddenly lost access to my NSS326 recently. I can't access the web interface, the NAS won't boot up and the display has the message "Mount Volume Please wait...". I've let it sit for days (based on what I've read on other discussions) with no luck. All of the led indicators are green. I tried booting without any of the disks and it said No Disk 0.0.0.0. I put the disks back in and it has the same message on trying to boot up.
Any ideas on what I could try. The support on this device ended back in 02/2012, so a Customer Service rep asked me to try the online forums.
Thanks in advance.

Sunil,
You can SSH to the NAS from the ethernet port. For advanced information about what can be done I recomend that you check the QNAP forums, since the device was manufactured by them. They have a very active community and many users seeking advanced troubleshooting information. The comparable QNAP model is TS-659 Pro+ and it has an Intel processor.
http://www.cisco.com/en/US/docs/storage/nass/csbcdp/smart_storage/release/notes/Ciscov1.5_to_QNAPv3.5_FW_RNs.pdf
You may need to create an account to search and post at the QNAP community forum. http://forum.qnap.com/
Please keep us updated and feel free to ask if you have any further questions.
- Marty

Similar Messages

NSS 326 Loading Drivers Please Wait

Hello,
Our NAS was unable to start up today and is perpetually stuck display "Loading Drivers Please Wait"
The console is continually giving the error "mdadm: Cannot open /dev/sdb1: No such device or address"

The NSS326 consist of 6 disks (/sdXY where X is a,b,c,d,e,f represented a=1, b=2, c=3, d=4, e=5, f=6 and Y is 1,2,3,4). The Y value is the partitions in a disk. The error "mdadm: Cannot open /dev/sdb1: No such device or address", is pointing to disk#2 on partition #1 which is boot partition. This is telling me the boot partition is bad and it is stucked in the recovering mode but failed to recover to restore the media for this partition. It is not looking good if boot partition is bad.
Can you describe what happened originally? What does the web admin show the status of your drives and volumes as? Is disk #2 LED keeps flashing ? Was the disk bought with the chassis ? Type of the disk ?
A workaround for this to continue to boot is temporary remove disk #2 (unplug and pull out only). DO NOT remove any other disk while system is powering.
When you have the access to SSH or CLI from the console, can you please post the print out from some of the commands below:
# cat /proc/mdstat
# cat /etc/raidtab
# cat /etc/storage.conf
# mdadm -D /dev/md0
# mdadm -E /dev/sda3
# df -h

Can't mount volume in test-tape - timed out waiting for bot

Hi all
i am having a setup for OSB ( using windows 2003 ent 32 bit , administrative server + mediaserver ) , i am using HP c1537a scsi Tape drive ( driver details Microsoft 10/1/2012 version 5.2.3790.0 ) , and while mounting the tape from OBTOLL it gives the following error.
before configuring the OSB i am successfully completed the backup and restoration using windows NTBACKUP utility.
ob> mountdev -w test-tape
Error: can't mount volume in test-tape - timed out waiting for bot
ob>
please guide me to resolve this issue
Edited by: 927832 on Apr 22, 2012 9:34 PM

Did you follow the installation and configuration guide and disable the services that get in the way of OSB operations?
Thanks
Rich

Exporting Volume File Maps, please wait ...?

I have just upgraded to Leopard and Logic 7.2. It all seems to be working well accept for this when I quit Logic a box comes up on the screen saying "Exporting Volume File Maps, please wait ..." .... and I wait ... it takes a very long time but eventually disappears (after about 4 minutes)
Does anyone know what this is and why it takes so long?
I never saw it when I was using Logic 7.1 on Panther
Thanks

Well it did that a few times and now ... it seems to have sorted itself out and does it unnoticed like you say.
Yay!

Z10 cannot mount volumes

New connection but z10 not recognised and mount volumes does not work. Play book threads suggest top/ip not running but mine is windows 7, any simple help appreciated Chris

uninstall BlackBerry Device Services and then plug in Z10 and wait for about 5 min to install drivers
I did this on my 64 bit 7 os
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Delete File From Mounted Volume

Hey,
I am trying to delete the "Calendar Cache" files on both my laptop PowerBook G4 and the Mac Pro Quad that I sync my calendars with. I am using ChronoSync and the individual calendars sync fine, but there is a little house keeping needed with the cache file. They need to be deleted on both systems in order to "refresh" the views of the calendars.
So after the sync of calendars, I have the software initiating an AppleScript that deletes both. Here's the script:
+(* PowerBook Files / delete cache file *)+
+(* Please note that both systems have the same username. This may be arise a conflict *)+
+tell application "Finder"+
+ activate+
+ tell application "Finder" to delete file "Calendar Cache" of folder "Calendars" of folder "Library" of disk "useranthony"+
+end tell+
+(* Mac Pro Quad/ delete cache file *)+
+tell application "Finder"+
+ mount volume "afp://10.10.10.1/anthonyabraira"+
+ tell application "Finder" to delete file "Calendar Cache" of folder "Calendars" of folder "Library" of disk "/volumes/useranthony"+
+end tell+
I am having trouble addressing a deletion on the networked Mac Pro Quad.

why send it to the trash just delete it...
(* PowerBook Files / delete cache file )
try
do shell script "rm -rf /Library/Calendars/Calendar\\ Cache"
end try
you may need a delay for the Mac Pro Quad to mount
( Mac Pro Quad/ delete cache file *)
--the mount and then the delay
delay 4
try
do shell script "rm -rf /THE-CORRECT/PATH-HERE/Library/Calendars/Calendar\\ Cache"
end try
Tom

Duplicate on mounted volume

Hi all
Im putting this script together using AS Studio, the script mounts a volume then goes to a specific folder checks to see if their are files in it that are less than 24 hours old then duplicates them to another folder then unmounts the volume.
I cant seem to get the files in the folder "Abf:untitled folder:" which are less than 24 hours old to duplicate to folder "Abf:untitled folder 2:", can I get some pointers as to where im going wrong please?
on clicked theObject
if name of theObject is "get" then
tell window "main"
set Comp_Name to name of current menu item of popup button "COMP"
set current menu item of popup button "COMP" to first menu item of popup button "COMP"
end tell
if (Comp_Name is "ABf") then
set aDayAgo to the (current date) - 1 * days
tell application "Finder"
set myVolume to mount volume "afp://APf:[email protected]/APf"
delay 5
get every file of alias "Abf:untitled folder:"
repeat with thisItem in the result
if the modification date of thisItem comes after aDayAgo then
try
tell application "Finder" to duplicate thisItem to "Abf:untitled folder 2:"
end try
end if
end repeat
delay 5
tell application "Finder" to eject "Abf:"
end tell
end if
end if
end clicked
Cheers
Budgie

Im stumped, and a bit lost, due to my nievity with AS, ive got as far as the below and tried numerous things, but I keep getting the same result.
AppleScript Error.
"Finder got an error: Can't get every file of "/Volumes/Absolute Proof/untitled folder/". (-1728)"
am Im missing the obvious?, or am I a bit thick? (be kind)
could I get a bit of help with sorting this please?
on clicked theObject
if name of theObject is "get" then
tell window "main"
set Comp_Name to name of current menu item of popup button "COMP"
set current menu item of popup button "COMP" to first menu item of popup button "COMP"
end tell
if (Comp_Name is "AB-Proof") then
mount volume "afp://HD:[email protected]/AP"
delay 5
set aDayAgo to the (current date) - 1 * days
tell application "Finder"
--update folder "AP:untitled folder:"
run script "Tell app \"finder\" to get every file of POSIX path of alias \"AP:untitled folder:\" "
repeat with thisItem in the result
if the modification date of thisItem comes after aDayAgo then
duplicate thisItem to "AP:untitled folder 2:"
end if
end repeat
end tell
end if
end if
end clicked
cheers
Budgie

Mounted Volume not shwoing up with Windows 2012 R2 failover cluster

Hi
We configured some drives as mounted volumes and configured it with Failover cluster. But it's not showing up the mounted volume details with Cluster Manager, it's showing the details as seen below
Expect support from someone to correct this issue
Thanks in advance
LMS

Hi LMS,
Are you doubt about the disk shown as GUID? Cluster Mount point Disk is showing as a Volume GUID in server 2012 R2 Failover Cluster I creating a mountpoint inside the cluster
and had the same behavior, instead of mount point name we had the volume GUI after volume label, that must by design.
How to configure volume mount points on a Microsoft Cluster Server
http://support.microsoft.com/kb/280297
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Install 8.1.7 on RedHat 9 hangs after Initializing JVM from ..Please Wait

I am trying to install 8i 8.1.7 on redhat linux 9. when I start the installer I initially got the first error below. I did export LD_ASSUME_KERNEL=2.4.1. Now the installation starts and I get
---FIRST ERROR---
[oracle@localhost Disk1]$ ./runInstaller
Initializing Java Virtual Machine from ../stage/Components/oracle.swd.jre/1.1.8/1/DataFiles/Expanded/linux/bin/jre. Please wait...
[oracle@localhost Disk1]$ /usr/local/downloads/Oracle8iLinux/Disk1/stage/Components/oracle.swd.jre/1.1.8/1/DataFiles/Expanded/linux/lib/linux/native_threads/libzip.so: symbol errno, version GLIBC_2.0 not defined in file libc.so.6 with link
time reference (libzip.so)
Unable to initialize threads: cannot find class java/lang/Thread
Could not create Java VM
---CURRENT ERROR---
[oracle@localhost Disk1]$ ./runInstaller
Initializing Java Virtual Machine from ../stage/Components/oracle.swd.jre/1.1.8/1/DataFiles/Expanded/linux/bin/jre. Please wait...
and then get back to the $prompt after some time and the welcome screen never comes up.
Whats wrong?

Hi,
Follow the Steps below as I managed to configure and Install it with the help of these steps
1. Things you need before the installation
Before you start installing Oracle, you need to have the following packages:
�     jdk-1.1.8_v3 - Blackdown Linux port of Sun's Java Development Kit
You can find it at www.blackdown.org
�     Red Hat Linux 6.2 compatibility packages
compat-libstdc++-6.2-2.9.0.16
compat-glibc-6.2-2.1.3.2
compat-libs-6.2-3
compat-egcs-6.2-1.1.2.16
You can find these packages on your RedHat CDs, download them from RedHat site, or from some mirror site.
�     glibc-2.1.3-stubs Patch from Oracle.
2. Pre-install actions
2.1 Installing compatibility packages
Install all of the RedHat 6.2 compatibility packages mentioned above by issuing rpm -Uvh package_name, e.g:
# rpm -Uvh /mnt/cdrom/RedHat/RPMS/compat-libs-6.2-3.i386.rpm
2.2 Installing Java development kit
According to jdk documentation, we will install it under /usr/local by issuing e.g.
# tar -xvjf jdk-1.1.8_v3.tar.bz2 -C /usr/local
Note that it is not necessary to add path to the java executables in PATH environment variable, so you can safely keep whatever jdk or jre version you already have.
2.3 User oracle, groups and software mount points
We need to create two groups, oinstall and dba.
The oinstall group will own all the installation files, so user oracle should have the oinstall group as its initial group. We also need one more group, dba, that will have oracle's SYSDBA and SYSOPER privileges granted. User oracle should have the dba group as its supplementary group. Note that all linux users (accounts) that are in group dba will also get these privileges.
# groupadd oinstall
# groupadd dba
# useradd -g oinstall -G dba oracle
# passwd oracle
Create directories in which database files will reside. Oracle recommends OFA - Optimal Flexible Architecture (see oracle installation guide), but in this example everything will be installed under /home/oracle:
# mkdir /home/oracle/product
# cd /home/oracle/product
# mkdir 8.1.7
# chown -R oracle.oinstall /home/oracle/*
2.4 Setting the environment for oracle account
We should now login as user oracle and put the following lines at the end of .bash_profile:
export LD_ASSUME_KERNEL=2.2.5
source /usr/i386-glibc21-linux/bin/i386-glibc21-linux-env.sh
export ORACLE_BASE=/home/oracle
export ORACLE_HOME=$ORACLE_BASE/product/8.1.7
export ORA_NLS33=$ORACLE_HOME/ocommon/nls/admin/data
export PATH=$PATH:$ORACLE_HOME/bin
unset LANG
First two lines modify your environment so that gcc and ld look for glibc 2.1.3 compatibility headers and libraries.
The unset LANG line is there because if LANG is set, java is known to generate JNLS Exceptions.
Listing of valid Oracle NLS Data parameters including supported languages, territories and storage character sets can be found here.
The .bash_profile should now be executed in order to initialize these variables:
$ source /home/oracle/.bash_profile
or we can just log off and than back on as user oracle.
If you use some shell other than bash (tcsh, sh, ...) all of those variables should be set according to syntax of your shell and put in script that automatically executes at user login.

Mount volume script doesn't work after upgrading to Yoesmite

I just upgrade my Mac OS to Yosemite and the boot up mount script doesn't work again.
try
mount volume "afp://admin:[email protected]/Multimedia/Music"
mount volume "afp://admin:[email protected]/workspace"
end try
Should I modify the mount script and how to do that?
Thank you so much.
Matthew Ho

I am having the exact same problem. I just did a complete re-install of max os x and did all of the updates..my hard drive had crashed so i had to replace it. lot's of fun.. and after the last upgrade i can't use my sound at all.. the sound shows that it's all the way up but it has the "no Smoking" sign as well..
i have tried to restart.. change options and whatever else i could .. i did notice that when i enable the option to show the sound icon on the main bar that there is just a blank spot where it should be.. and i can't change it form there either because it just doesn't show..
any one seen this before.. ?
all my other Mac's work fine..
please help..

Mini goes directly to "IHEART RADIO launching. Please Wait" That one hour ago. Nothing happens. No keyboard input seems possible. Any suggestions?

I turned on the MAC, Until today, everything worked fine (slower with the new OS). But this morning, I got "IHEART RADIO launching. Please wait" in the middle of the screen as soon as power was on. No apple logo, or password log in. That was one hour ago. I've unplugged the **** thing, waited, plugged it in again, still no change. Unable to use Mini at this time. Any ideas?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

NAS NSS 326 Reset Issue.

Hi peeps
Have a little issue with a Cisco NAS NSS 326 Smart Storage 6 bay - with RAID 5 over 6 disks.
Apparently there were some funny business with the performance with the device so someone reset the device from the button on the back.
I've been ask to get everything working but I've bumped into a little problem.
The DHCP address the device pick up is 10.2.7.127, so I open up a web interface and hop on that address and configure password, time etc.
When it comes up to step 6 I've tried selecting "Do not set disk configuration" and RAID 5, then on the finish window to start installing it advises it'll format all disk to continue!!!
We have a lot of data (9GB or so)
Is it possible to continue in any way without clearing the data we have on it? or map it somehow to recover the data?

Marc,
I would first back all data you wouldn’t want to lose since the volume is unlocked now. Instead of a hard reset we can attempt a reset of admin password. Administration guide: PG- 39
http://www.cisco.com/en/US/docs/storage/nass/csbcdp/smart_storage/admin/guide/NSS32X_Admin_Guide_OL21155_v1.5.pdf
Reset Network Settings and Password
You can restore the network settings and password for your NAS device using the
reset button located on the back panel. The NAS device should be powered on for
this procedure. Using a paper clip, press the reset button for 3 seconds, until the
NAS beeps.
The following settings are reset to default:
• System administration password: admin
• Network settings:
- Obtain TCP/IP settings automatically via DHCP
- Disable Jumbo Frame
- System management port - 8080
• System tools: IP filter settings - Allow all connections
• LCD panel password: (blank)
This 3 second reset should only clear out these fields but back up all data as a precaution.
Hope this helps,
Jasbryan.

OS X Lion and NSS 326

I've got a Cisco NSS 326 NAS and have recently run into a problem with OS X Lion Developer Preview and authentication to the NAS. When connecting to the NAS over AFP as guest I can access the NAS just fine. However, when I try and authenticate I get an error that reads:
"The version of the server you are trying to connect to is not supported. Please contact your system administrator to resolve the problem."
I've read on another site (http://trick77.com/2011/02/25/afp-broken-linux-based-nas-mac-os-x-lion-10-7) that this has to do with the version of AFP that is running on the NAS compared to the new version that OS X Lion is using AFP 2.
Does anyone have a solution to enable the NAS to support AFP 2 or are there any plans to support this from Cisco any time soon?

Hi all NSS32x owners,
Like you all, I bought a Storage Solution from Cisco, personally hoping that Cisco would be better in supporting us than the OEM they bougth the NSS32x line from.
Until now I have been disapointed over and over.
They opened a discussion about what should be implemented in the Cisco versions of the NAS'ses but so far no real addition of any value.
Now we are facing the problem with OS X Lion's TimeMachine incompatability, which could have been solved for months ago, when the first developer releases were issued.
No response from Ciso however.
This is really bad.
Other companies already have solutions for their products in order to be compatible with Lion.
Ok, I agree, this might not be a problem caused by Cisco, but a problem that was caused by Apple when releasing Lion. But hey all companies have to update their software so Cisco as well as Apple.
However, companies of major size (Apple, Cisco, and many others) should be more cooperative when releasing new software.
I work in IT for over 30 years now and I have always seen that when Cisco bought a company, their "boxes" were painted gray and the Cisco "bridge" logo was aplied and then all over sudden it became a REAL Cisco product.
And I mean it really became a Cisco product. You might have some minor problems but those were always solved.
I would have expected the same from Cisco with respect to these NAS'ses.
And believe me, I have seen quit some NAS'ses from the competitors but the NSS32x series does not come with the support you get from other competing NAS vendors.
That is what bothers me and I regret that there is no solution today for the issue(s) we have with OS X Lion, but what bothers me even more is that Cisco is not informing us at all about whatever solution there will be within whatever time frame.
I still have the NSS326 and I had to pay quit a premium over other vendors, but accepted it, supposing that the NAS would have the support I am familiar with from Cisco, but as you can read above I am disapointed.
So Cisco, what are you going to do to improve support and be more open and informative about coming software releases for the NSS32x series NAS'ses?
Regards,
Klaas de Jong

Mount volume not working in 10.4.6

Could someone please explain why this script does not work in 10.4.6?
tell application "Finder"
activate
mount volume "afp://192.168.1.100/thesharetomount"
end tell
Works fine in 10.3.9 but 10.4.6 gives error "some object was not found"
Thanks for any info

Managed to figure out a trick to get around this problem.
I added user name to the mount command
tell application "System Events"
set myuser to get full name of current user
end tell
tell application "Finder"
activate
mount volume "afp://" & myuser & ":@192.168.1.100/sharetomount"
end tell
Now it works but can't figure out why it does not without giving a user name?

Please Wait.

OK this is totally unfair, I purchased a MuVo-TXFM and it worked great, I was the happiest guy in the world for 2 weeks I think, I loved it!!..then I got the brilliant Idea of pulling up the creative website, and noticed that there was a firmware update. I looked at the what I currently had and saw it was .xx , I saw that there was a .3, it spoke of firmware this being a fix for .00xxx, I investigated it and saw it added features like cue/review (I had before) and fixed a volume issue ( I didnt have) anyways I went ahead and updated it, it went on fine, and succefully updated me to .3.03.
NOW it acts stupid, when I turn it on not it says "Please Wait.." It never did that before, its slower, and it forgets my presets, happened 3 times now, once the battery went dead, the other two times, it was just turned off.
Is there archi'ves for the . firmware anywhere? ot this is going back to futureshop I tried to re-flash the bios with the .3 firmware again and it again said successful but still acts retarded. So one last time I formatted it, flashed it again, pulled the battery, put a brand new Energizer (had a duracell) and tried one last time.. still its acting like I dropped it off the CN tower.
Has anyone had this problem? or seen this stupid "Please Wait.." screen? I liked it better before, I regret updating the firmware, and want the version back.
Can anyone help before I make the trip back to futureshop? is there a way to factory reset it's I can prob take it apart and pull the memory battery, that will VOID my warrantee Im thinking. .HELP please someone.
Realrobley

hehe.. muawaahaaa
Lucky for me I found a 3rd party hack site that fixed it, and added some cool features extra, thank you softpedia, , this rocks, I have a balance, a DX option for FM, and I can change the eq settings for pop, rock, ect.. heck before I coudnt even see the eq setting for those , just the custom one, theres like 0 different sounds, and a better battery indicater bar has 8 (across the sceen) not like the cheesy 4.(factory) . anways its called firmware v. .2.95 and ONLY works for the TXFM MuVo.
Wel thanks anyways everyone, im back and mehe

NSS 326 Mount Volume Please Wait...

Similar Messages

Maybe you are looking for