NSU/Nokie Connectivity Cable issues

I've tried running the software updater. amd it just comes up with an error:
nsu_ui_client.exe has encountered a problem and needs to close. We are sorry for the inconvenience. (this running version 1.3.40en)
I have attempted to download the NSU from the Nokia Website which is successfull and then attempted to install it. I get prompted that it needs to Install the Nokia Connectivity Cable and then as it does this, it kills my ethernet controller and I lose all internet connectivity.
I then have to restore my PC back to a previous point to enable the Ethernet controller again.
I have successfully update the Phone (N70) previously, but for some reason can longer run the existing NSU installation on my Pc or install a new Version without killing my ethernet Controller.
Any Help gratefully received.
Cheers

Here is some stuff that you can try;
In a self troubleshooting effort to try to obtain better connectivity / more wiggle room, check to see if there are there any excess/unneeded coax cable splitters in the line leading to the modem that can be eliminated/re-configured. Any splitters that remain should be high quality and cable rated for 5-1000 MHz, bi-directional, and no gold colored garbage from Radio Shack, Home Depot, Target, etc. Splitters should be swapped with known to be good / new ones to test.
If there aren't any unneeded splitters that can be eliminated and if your coax wiring setup can't be reconfigured so that there is a single two way splitter connected directly off of the drop from the street/pole with one port feeding the modem and the other port feeding the rest of the house/equipment with additional splits as needed, and you've checked all the wiring and fittings for integrity and tightness and refresh them by taking them apart then check for and clean off any corrosion / oxidation on the center wire and put them back together again, then as Jay has stated, perhaps it's best to book a tech visit to investigate and correct.

Similar Messages

CA-53 Connectivity Cable Issue with 6233

I just bought this cable , installed drivers on my pc , plugged it into the PC and then into my phone (6233).
OOPS "Enhancement not Supported" error... I've been busting my head for the last hour reading forums, but i haven't found anything i can do that doesn't involve going to get it "Fixed" or killing myself... I've tried rebooting and removing battery. I also wanted to update my firmware... but oops my cable doesn't work ... If you can give me a hint about what to do , that doesn't involve killing myself ( I'd Really rather live ) I would love you so much ... (Thats the rage talking)Also, in my connectivity menu, my USB Data cable thing is grayed out...
P.S I just tried the cable on a 6230 phone - same error... Could that mean old firmware, broken cable thingy, or something else?
Message Edited by deathwalk on 21-Apr-2008 07:56 PM

Hmm, our m8 have suggested that procedure in the assumption that there's no hardware fault involved. And what you have experienced could be brought about by 3 causes namely software, cable fault, or the port of the phone in which the cable is connected.
You have to narrow it down & the people who will have another cable, or phone for testing would be the Nokia Care Centre. Unless of course you knew somebody who have a phone or a cable that's the same as you have.
Knowledge not shared is knowledge wasted!
If you find it helpfull, it's not hard to click the STAR..

Connectivity Cable Drivers: Not Installed???

I have installed the PC Suite 6.82; I have installed the Nokia Software Updater 1.1.40en; I have perfectly synchronised my Nokia N73 using PC Suite, but it still can't be discovered by the NSU. When I tried to look up why this problem had appeared, I found in the System Info given to me by the PC Suite that Connectivity Cable Drivers had not been installed. I checked in Control Panel - they WERE there. Anyway, I decided that uninstalling and reinstalling PC Suite and NSU will solve the issue, but it didn't. I still CAN synchronise the phone and CAN'T get it discovered by the NSU and thus - update its firmware.
Any ideas of how the problem could be solved?Message Edited by ivoalex on 18-Nov-2006
07:05 PM
Message Edited by ivoalex on 18-Nov-2006
07:06 PM

Try reinstalling just the drivers (pick the drivers for the cable you have):
http://europe.nokia.com/A4144936

Unable to un-install Nokia Connectivity Cable Driv...

I am having the same issue as many other users with Nokia PC Suite 6.8.
I am running Windows XP SP2 on a IBM R52. In the office, they installed the latest driver updates from IBM and since then, I cannot use PC Suite. So I upgraded to 6.8 to no avail.
I am getting the message when choosing "get connected" "there is no available connection type and therefor connection to the phone cannot be established....etc"
I used PC Suite Cleaner 3.4. It does however not remove the Connectivity Cable Driver and PC Connectivity Solution. So I tried that in Control Panel. I get the message "the feature you are trying to use is on a network resource that is currently unavailable. Click ok to try again or enter an alternate path to a folder containing the installation package Nokia_Connectivity_Cable_Driver.msi in the box below". I get the same message when I try to uninstall the PC Connectivity Solution.
I have also run registry cleaners, removed PCSuite, rebooted etc etc...
I feel that I must also remove the Connectivity Cable Driver and PC Connectivity Solution but I simply can't.....
help please!! thanks in advance...
Solved!
Go to Solution.

22-Oct-2006 10:38 PM
dutchkiwi wrote:
I am having the same issue as many other users with Nokia PC Suite 6.8.
Recently because of some destructive viruses obliged reinstalling Windows XP SP2 on my lapTop-Dell Inspiron 6400 again. I installed the latest driver updates from the internet and since then, I cannot use the letest version of PC Suite. So I tried upgrad it to (Nokia_PC_Suite_rel_7_0_9_2_eng_web) .
I am getting some error messages when getting started installing above mentioned version of pc-suit. As yow know to reinstall a new program windows first remove the existing one throuh the system.
I used windows install Cleaner cleanup to clean the cable drivers and pc connectivity . It does however not remove the Connectivity Cable Driver and PC Connectivity Solution. So I tried that in Control Panel. I get the message "the feature you are trying to use is on a network resource that is currently unavailable. Click ok to try again or enter an alternate path to a folder containing the installation package Nokia_Connectivity_Cable_Driver.msi in the box below". I get the same message when I try to uninstall the PC Connectivity Solution.
I have also run registry cleaners, removed PCSuite, rebooted etc etc...
I feel that I must also remove the Connectivity Cable Driver and PC Connectivity Solution but I simply can't.....
help please!! thanks in advance...

Connecting cables For MacBook to a VGA

What connecting cables can I buy to connect my MacBook with a (I guess) standard size DVI to a VGA standard? All I can find are Mini-DVI (which I don't have on my MacBook) to VGA. Help!!!

Here is exactly what both of my MacBooks say and in the post after yours, there are two pictures of DVIs, the top one being the original, bottom the Mini-DVI... BOTH of my MacBooks have the ORIGINAL larger DVIs....THAT is my problem, I cannot find an adapter that will take me from the ORIGINAL DVI to a Standard VGA.... Incidently, I bought both of these at different times, different places so would assume MY issue would not be isolated. Past the occasional need to have a larger display, I love these machines and really don't like being forced into buying different machines to satisify my viewing needs. Thanks for you time, attention and suggestions, they are ALL appreciated! - Doc57
Model Name:          MacBook
Model Identifier:          MacBook4,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.4 GHz
Number of Processors:          1
Total Number of Cores:          2
L2 Cache:          3 MB
Memory:          4 GB
Bus Speed:          800 MHz
Boot ROM Version:          MB41.00C1.B00
SMC Version (system):          1.31f1
Serial Number (system):          W8xxxxx0P5
Hardware UUID:          9FBC6B3A-4F33-5B81-9EC0-B98B5954F93C
Sudden Motion Sensor:
State:          Enabled
<Edited By Host>

Computer reboots shortly after connecting cable to ipod

Just recent got new fifth gen ipod 30 and installed itunes, set up library and playlists. Now ready to connect cable to my USB 2.0 and within 30 seconds after connecting, BAM my computer reboots itself. I later get a signiture message 'BCCODE:19'(and more info). The ipod display prior to reboot indicates "do not disconnect" however, it freezes after the reboot. HELP!! Ipod has downloaded some songs but I need help troubleshooting possible hardware or software conflicts to make any headway. What are my options to remedy this problem forever? Thank you.

Hi Sherif
It's probably worth trying a couple of standard trouble shooting techniques:
- Reset the PRAM: http://support.apple.com/kb/HT1379
- Reset the SMC: http://support.apple.com/kb/HT3964
Resetting the SMC often fixes battery/power supply issues; resetting the PRAM probably won't make any difference but it only takes a few seconds and is quite harmless.
Bob

Connectivity cable driver

Hello,
I have a problem when I try to install PC Suite 683
I get error: "Another version of Nokia Connectivity Cable Driver has been detected. Please remove it before continuing."
I don't know what to do else.
Here is the things I tried:
1. add/remove programs->uninstall connectivity cable driver
2. pc suite cleaner
3. search and delete from registry every key where exists any of words (nokia, pc suite, connectivity cable)
4. install nokia connectivity cable driver and uninstall it
5. i'v searched and removed files containing word "nokia" (all that can be related to nokia)
and i still get the same error.
i have installed version 67 - and it works just fine
Thanks for any ideas
system:
Win XP Pro sp2Message Edited by rupertas on 08-May-200711:17 AM

Hi rupertas
Have you tried getting Windows Installer CleanUp Utlity - msicuu2.exe from Microsoft
Please see post by diving_catch concerning this issue to remove both "Nokia connectivity Driver" and "PC Connectivity Solution" programs
Happy to have helped forum in a small way with a Support Ratio = 37.0

Unable to uninstall the Nokia Connectivity Cable D...

hi,
i had nokia PC suite version 7.1 which i uninstalled but the nokia connectivity cable drivers were not getting uninstalled, every time it gives me a error about the .msi file mising. i've tried in the safe mode but no go. i've also deleted all nokia folders from the program files and the registery in safe mode but still no go... i've also tried using the PC suite cleaner.. but still the same issue...
Please help
regards,
Gulrez

You obviously deleted the files before uninstall. Just reinstall PCSuite. Use a program called Revo Uninstaller to perform a clean uninstall and clean up the registry mess after with the same prog.
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

Connectivity cable driver fatal error

Whenever I link my Nokia to the PC windows XP SP3 detects new hardware and tries to install driver. It finish the installation with error
There was a problem installing this hardware Nokia N70 USB Phone Parent
An error occurred during the installation of the device
Fatal error during installation
What can I do here?

Hi jcmn,
Could you please confirm more details regarding your issue?
Which PC Suite you are using along with your version details?
What is your connectivity cable driver version you are having?
Being a proud owner of Nokia NSeries handset, you have options of 3 pc suite you can use to connect your N70 with the PC
Nokia PC Suite 7.0.7.0
Nokia NSeries PC Suite 2.0.262.0
Nokia OVI Suite
If you have already having old connectivity cable on your PC installed ( not the latest one) then uninstall your existing connectivity cable driver and then reinstall the latest connectivity cable driver and then try to connect your phone with the PC. Best of luck

When connected cable ethernet and assign ip address windows automatically restart

Hello ,
i have windows 7 with 2 NIC ,the additional Network card working fine
but the built-in card when connected cable and assign ip address automatically restart
please help to avoid this problem
thanks

Hi,
first, try the jacky's solution, and verify if the issue is not from Hardware.
and , It looks like the definition of distributed by
policy for more secure.
I remember in the past I've set up for
such a solution for company to prevent
unauthorized access.
Please check with your network administrator
and security if is defined.
You can examine the event log to identify if you have
trigger for action .
you can see this link about the identify if you have trigger :
http://windows.microsoft.com/en-us/windows-vista/automate-tasks-with-task-scheduler-from-windows-vista-inside-out
thanks,
Israel Chemo

Can anyone help me restore an ipod itouch ,tried restore on itunes but it fails everytime the error code says it's a conection problem i have 2 computers and tried all usb ports but keephaving the same problem ,even bought a new connection cable

Went to update the ipod touch and it wiped out everything , Itunes keeps trying to restore it but fails everytime giving me an error that it cannot see my ipod yet it sees it and tries to restore it everytime i connect the ipod to the pc , the help file suggested i reinstall the latest version of I tunes so i did i tried using different ports on 2 computers and also bought a new connection cable but still won't restore can anyone help?

Try a manual install, as outlined in the link below.
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

My Internet Connection Dropping Issues...

I too am having the occasional Internet connection dropping issues. Phone and TV continue to work.
Since I had Fios installed last November I am on my third ONT and 2nd router. When I called in my latest drop yesterday the call center person told me I had a hardware issue because my computer had a valid IP address assigned. I tried to teach her something about DHCP but she would not listen to me. I asked her to please reboot the ONT and she refused because "nothing was indicating a problem with it". Whatever...
Each time the Internet goes out the router acts fat and happy. I have full green on WAN Coax, and strangely enough, a flashing green Internet activity indicator. Logging into the router shows that I am MOCA connected and assigned a WAN IP address. But I can't get out past the router at all. On the event that led to me getting a replacement router the lady said she could talk to the ONT just fine, but not the router. We reset the router and ONT port numerous times and the connection finally came back up.
I am not sure of the protocol between the ONT and router, but I think the ONT is keeping enough signal going to make the router "think" its happy, but then the ONT is not passing packets at some point. After yesterdays call and the refusal to reset the ONT I just hung up on her and reset it myself. Of course everything started working just fine...like I thought it would.
So what is the issue here? Is MOCA a mess? Is an Ethernet connection to the ONT better? I am utterly disgusted with this miserable system and can't afford to continue having these outages.
I should also add the other wonderful features I have seen. When I tried to powercycle the *new* router yesterday it decided to dump its entire config including my port forwarding. Nice... And I have given up using wireless because if I set the router for WPA it locks up so hard that it takes a master reset to get going again.
Anyone have some advice on getting this system stable?

I would try using a non-verizon router. I used the Netgear router and it fixed my problem. The Verizon router seem to be pieces of garbage and they over-hear.

Can you get an virus or trojaner through the connection-cable (PC) from your iPod touch?

I had an trojaner on my PC earlier and my iPod touch 4G was connected to my computer. Is it possible for the trojaner or viruses in general to make their way through the connection cable or something? If a photo or something wasn't infected. I mean sync-wise, etc.

It would be very difficult for a virus or trojan to get from the iPod to your PC via USB. Attaching a virus to any media file such as a photo or music track is very, very difficult, and all known exploits that would do this were blocked a long time ago. Attaching a trojan would not be possible. Unless there's a new exploit I haven't heard of, only if a trojan program was attached to an email and from there transferred to an app that could then be synced to your computer would it be possible malware come from your iPod. I think that rather unlikely and that your trojan got into your PC from some other source.
Regards.
Message was edited by: Dave Sawyer

The older version of Nokia Connectivity Cable Driv...

Trying to install the actual version (even Beta 3.1) of Ovi Suite fails with the error message "The older version of Nokia Connectivity Cable driver cannot be removed" (Error 1714)!
Im running a Win 7(64bit) Pro system and used to have PC Suite 7 installed.
PC Suite 7 was uninstalled before I attempted to install the new Ovi Suite. As it failed with the error message above, I called the Nokia hotline, deinstalled all existing Nokia software and tried to run PC-Suite Cleaner 7.1.1. Regretfully, PC Suite cleaner hangs up immediately.
Scanning my computer for Nokia entries on advise from the hotline, all Nokia files were deleted and the registry was scanned and cleaned from Nokia entries as well.
Obviously some remains of the cable driver are hidden in the system somewhere.
Could anybody please help ? I need to synchronize my X6 on a regular basis.
Thanks !

Can't you see 'Nokia Connectivity Cable drivers' in the Windows Control Panel ?

Connection pool issues with Mysql

Hi,
I have defined sufficient read connections (50) in the toplink configuration, I am finding toplink is not releasing the connections in Mysql, this is when run from Jboss App server.
Is anyone aware of toplink connection pool issues with MySql?
thanks

TopLink always closes connections, I cannot see how this could occur.
Please include your persistence.xml or sessions.xml. Also ensure you are closing your EntityManager or ClientSession, especially if using exclusive connections.
Also include the exception you are getting.
James : http://www.eclipselink.org

NSU/Nokie Connectivity Cable issues

Similar Messages

Maybe you are looking for