NTDETECT FAILED boot up error??

Every support tech I talk with has no idea what this error is and tells me my only option
is to do a clean install. Can anyone offer any help or advice.
Thanks

Welcome to Lenovo forum!
Please tell us:
What model type?
What OS ?
What applications (TVTs) if applicable
Summary of the observed conditions - "what happens, when?"
Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
Please insert your type, model (not S/N) number and used OS in your posts.
I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
English Community Deutsche Community Comunidad en Español

Similar Messages

Windows failed to start error

Windows failed to start error
I am running a Compaq mini 110c netbook and the following error message occurred on start up. The netbook does not have a slot for a disc as everything was in the netbook already. I am a complete technophobe and need help to restart my netbook.
windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
1. Insert your Windows instalation disc and restart your computer.
2. Choose your language settings, and then click "Next."
3. Click "Repair your computer."
Status: 0xc000014c
File: \Boot \ BCD
Status: 0xc000014c
Info: An error occurred while attempting to read the boot configuration data.
Help please!!! Answers must be in plain everyday language that I can understand!!!

The following 2 links should help with the issues you are having. I would suggest attempting a system restore first (not I repeat not a system recovery) make sure you are doing the restore option or you will lose everything.
Click the option to "Using System Restore when Windows 7 cannot start normally"
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01835735&lc=en&cc=us&dlc=en
The below link is for other basic troubleshooting that might help if the above doesn't work:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443371&cc=ad&dlc=en&lc=en&jumpid=reg_r1002_us...
Hopefully the steps are basic enough for you to understand and help out. Thanks
I am an HP employee.
Please post rather than sending a Private Message. It's good for the community and I might not be able to get back quickly.- Thank you.
Please click the White Kudos star on the left to say thanks.
Please mark Accept As Solution if this resolves your issue.

External Drive Disk Erase Failed with the Error Input/Output Error

I have 2 hard drives in an external FW800 enclosure that I am unable to format. When I go to initialize the drives in Disk Utility, I get the following error message: "Disk Erase failed with the error: Input/output error."
The drives show up in Disk Utility, but I can't repair them (that option is grayed out). Disk Utility correctly ID's the manufacturer of the drives (Maxtor), their size (200gb each), so it's obviously seeing that the drives are there. But it won't let me format them.
The drives are new, by the way; they don't have any data/files on them. I have Disk Warrior, but the drives don't show up there to be repaired -- probably because they aren't formatted yet.
After looking at other posts, I tried switching the jumper settings around on the drives -- from Master/Slave to cable select and back again, but it didn't help. I also tried doing a zero erase (even though the drives are new), zapping the PRAM -- again, no help.
One question I had is whether this could be a bad FW800 cable? The cable is new -- it came with the enclosure, which is an OWC Dual FW 800 enclosure. Other than that, does anyone have any other thoughts about what's causing this? Any help would be greatly appreciated.
Matthew

SOLUTION!!!!
I had the exact same problem. I have the original 20 GB hard drive that came in my Powerbook G4 550MHz and a couple of years ago I traded up for a 60 GB drive and bought a FW/USB enclosure for my original drive to use it to backup my important files. I hadn't backed up in over a year (shame on me!) and I decided maybe I should erase the drive and start from scratch. It was connected via USB.
At that point DiskUtility gave me the exact same Input/Output error. I tried partitioning the drive into 1 or more partitions but came up with the same error. I couldn't figure out what was wrong so I decided to startup in OS 9.2.2, I did that and let it start up, then plugged in the hard drive and it gave me the standard "This disk is unrecognizable, do you want to eject or erase?" so I clicked Initalize. It worked!
Just make sure you choose the MacOS Extended option when initializing out of OS 9 (instead of the MacOS Standard option) so it can be read and viewed in OS X.
If your computer is too new to be able to boot from an OS 9 folder on your drive or an OS 9 CD, then see if a friend or a local library has older computers that are running OS 9 or can boot from it. If not let me know and you can send me your drive and I'll reformat it.
Kind of crazy...I haven't used the OS 9 partition on my HD in YEARS...was even thinking about erasing it since I don't use any Classic applications anymore...good thing I didn't!
Nick
Powerbook G4 550Mhz Mac OS X (10.4.6)

Is my HD Dead? Reformat Disk Utility Error: secure disk erase failed with the error could not open disk.

Hi,
Fed up with seeing the spinning beach ball I decided to reformat my MacBook Pro...
After backing up everything on an external hard drive I put in the OSX install DVD, restarted the machine and held down 'C'.
I followed the install prcedure, clicking next a few times etc...
I then went into Utilities > Disk Utility. I chose 7-Pass to erase the Macintosh HD and set it off erasing.
I checked the process an hour in and message on screen read:
Secure disk erase failed with the error:
could not open disk
The internal hard drive no longer exists in the disk utility so I cant retry erasing it.
The only thing that appears in disk utility is the OSX install DVD.
I can't even shut down the mac as everything under the apple tab is greyed out!
I'm guessing this means my hard drive is broken right?
If anyone has any other ideas of what to try I'd really appreciate that.
How do I turn the machine off?
If my hard drive is gone then should I consider getting an SSD drive?
Any recommendations for such a drive would be great.
Hope you can help!

Did you partition the drive?
Extended Hard Drive Preparation
1. Open Disk Utility in your Utilities folder. If you need to reformat your startup volume, then you must boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Click on the Options button, set the partition scheme to GUID (only required for Intel Macs) then click on the OK button. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Steps 4-6 are optional but should be used on a drive that has never been formatted before, if the format type is not Mac OS Extended, if the partition scheme has been changed, or if a different operating system (not OS X) has been installed on the drive.

Partition Failed Partition failed with the error: POSIX reports: The operation couldn't be completed. CAN NOT ALLOCATE MEMORY

I plug usb mass storage device to my macbook pro i7 than every thing is stack and i reinforce to shutdown and than I start again but mac fail to boot again.
I tried different optiones in disk utility in mac os startup disk. but still fail to repair, erase and partition. I try to fix with the steps listed in
https://discussions.apple.com/message/13288923#13288923
but it fail to partition with the msg:
Partition Failed
Partition failed with the error: POSIX reports: The operation couldn’t be completed.cannot allocate memory
pls pls pls help urgentely on this matter I stop working.
Kind Regards,
pe

Hi again OGELTHORPE.
I've already run two hardware tests. One quick one and one extended one. It was unable to pick anything up.
It's like everything is running perfectly, but when I go to erase the HDD or partition it, it pops up with the error message. Even when I try to erase and partition using "Terminal", I received the same error message.
It's beginning to do my head in, but will see if replacing the SATA cable will make any difference. If it doesn't, I'll hazard a guess it could be the Logic Board.
Thanks again for your suggestions!
L.

Partition failed with the error: No space left on device

I used Boot Camp Assistant (for instaling Windows XP) and there was Partition error:
+*The disc cannot be partioned because some files cannot be moved.*+
+Back up the disk and use Disk Utility to format it as a single Mac OS Extended (journaled) volume. Restore your information to the disk and try using Boot Camp Assistand again.+
so I tried Yasu, verified permission, verified disk, and everything was ok, but in Disk Utility I was trying to split or change size of my disk but there is one error again:
+*Partition failed.*+
+Partition failed with the error: No space left on device+
but I have 64GB free space!
how must I "+Restore your information to the disk+" or what else can I do?
thanks!

arajs wrote:
I used Boot Camp Assistant (for instaling Windows XP) and there was Partition error:
+*The disc cannot be partioned because some files cannot be moved.*+
+Back up the disk and use Disk Utility to format it as a single Mac OS Extended (journaled) volume. Restore your information to the disk and try using Boot Camp Assistand again.+
so I tried Yasu, verified permission, verified disk, and everything was ok, but in Disk Utility I was trying to split or change size of my disk but there is one error again:
+*Partition failed.*+
+Partition failed with the error: No space left on device+
but I have 64GB free space!
how must I "+Restore your information to the disk+" or what else can I do?
thanks!
This is a standard error message.
If you would have checked into the bootcamp forum you would have instantly found the solution.
http://discussions.apple.com/forum.jspa?forumID=1244&start=0
All that error message means is that you do not have enough conguous disk space available. No big deal at all for an older system. You have bits of files strewn over the "free space."
The solution as you would find in the bootcamp forum is to clone your HD, using a file-file clone, then test the clone to be sure it is working and then to erase your HD and clone back.
Works every time.
Message was edited by: Theodore

SCCM 2012 Export Task Sequence fails with generic error message

We have a complex task sequence comprising of more than 50 applications\packages, 1975 drivers, 18 driver packages etc etc. Its long, it's big and it will not export with it's content.
We have several environments for development test and live. I am attempting to export the primary task sequence with all it's dependencies from live so that I can port it over to a new development environment.
I can export the zip file without content and it comes to 92Mb in size. The entire task sequence software set is 50Gb+. When I attempt to export with all dependencies and content the process gets about 60% of the way through and fails with the error
"Error: The filename, directory name, or volume label syntax is incorrect"
Googling the error roughly defines the problem as 'the export process cannot access the defined source path for one of the dependant items'
I wrote a PowerShell script that looks as every application, package, driver, driver package, boot image, os image and software update package in the entire SCCM software library and verifies that each and every package has a valid UNC source directory
that can be reached using test-path.
I also wrote another tool that parsed the entire source software library on the server looking for permissions errors (permissions on the structure set at a directory level rather than inherited), directories that were too long, inaccessible or otherwise
blocked, nothing was found.
It will take a very long time to go through and check each and every dependency by hand - time I do not have at present.
I looked in the TaskSequenceProvider.log as that is supposed to contain messages from the export process and found the messages in there far too high a level to use
=======================
<![LOG[Setting status complete: status code = 0x0; ]LOG]!><time="13:00:41.161-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="4168" file="exterror.cpp:128">
<![LOG[[PID: 3500] Invoking method SMS_TaskSequence.ExportXml]LOG]!><time="13:00:42.339-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="4168" file="wmiprovider.cpp:333">
<![LOG[[PID: 3500] Done with method SMS_TaskSequence.ExportXml]LOG]!><time="13:00:42.341-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="4168" file="wmiprovider.cpp:352">
<![LOG[Setting status complete: status code = 0x0; ]LOG]!><time="13:00:42.341-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="4168" file="exterror.cpp:128">
<![LOG[[1AFF658 PID:3500] Received shutdown request from WMI]LOG]!><time="13:01:36.036-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="5592" file="wmiprovider.cpp:399">
<![LOG[[1AFF658 PID:3500] Initializing provider for namespace root\sms\site_P01]LOG]!><time="13:02:36.550-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068"
file="wmiprovider.cpp:90">
<![LOG[[1AFF658 PID:3500] Initialization of provider for namespace root\sms\site_P01 succeeded]LOG]!><time="13:02:36.551-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1"
thread="7068" file="wmiprovider.cpp:107">
<![LOG[[PID: 3500] Invoking method SMS_TaskSequence.LoadFromXml]LOG]!><time="13:02:36.554-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:333">
<![LOG[[PID: 3500] Done with method SMS_TaskSequence.LoadFromXml]LOG]!><time="13:02:36.558-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:352">
<![LOG[Setting status complete: status code = 0x0; ]LOG]!><time="13:02:36.559-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="exterror.cpp:128">
<![LOG[[PID: 3500] Invoking method SMS_TaskSequence.ExportXml]LOG]!><time="13:03:05.428-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:333">
<![LOG[[PID: 3500] Done with method SMS_TaskSequence.ExportXml]LOG]!><time="13:03:05.431-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:352">
<![LOG[Setting status complete: status code = 0x0; ]LOG]!><time="13:03:05.431-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="exterror.cpp:128">
<![LOG[[1AFF658 PID:3500] Received shutdown request from WMI]LOG]!><time="13:03:36.369-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:399">
====================
Is there any way of increasing the log verbosity? I need to see what item is causing the export to fail.
Is there another log containing the information about the export & what it is doing?
All out builds that use the task sequence complete successfully, we can edit the sequence fine, make changes etc. so no internal corruption we can find.
Any ideas?

Torsten, smsprov.log did indeed prove useful, I could see every package as it was validated. Unfortunately the log was wrapping about every 4 minutes and it takes 3+ hours for the task sequence to reach the fail point so I still cannot see the offending
package as it wraps before I can get to the log.
I will increase the size of the log and see if I can maintain some details to investigate.
There was nothing of note in the event logs, certainly nothing leading me to suspect that WMI might be reaching its limits.
I will keep looking for the cause and will post here when I find it <= positive thinking :)

After re-inistalling windows 7 ultimate the validation process fails and reports error code 0xC004E003

Hi I have just reinstalled Win 7 Ultimate and the validation has failed due to error code 0xC004E003. all of the windows updates have been complete.
when I run slui 4 and I do not get an option to activate by phone and I have tried running the Command prompt "cscript %windir%\System32\slmgr.vbs /ilc %windir%\System32\licensing\ppdlic\Security-Licensing-SLC-ppdlic.xrm-ms" which errored
out
Bellow is the MGADiag tool output
Diagnostic Report (1.9.0027.0):
Windows Validation Data-->
Validation Code: 0
Cached Online Validation Code: 0x0
Windows Product Key: *****-*****-X92GV-V7DCV-P4K27
Windows Product Key Hash: aU2z1/fnhnLHmhBm699qYZT2E6s=
Windows Product ID: 00426-OEM-8992662-00400
Windows Product ID Type: 2
Windows License Type: OEM SLP
Windows OS version: 6.1.7601.2.00010100.1.0.001
ID: {58492533-DAC0-4F4B-8CB4-7C2572CD6AD2}(3)
Is Admin: Yes
TestCab: 0x0
LegitcheckControl ActiveX: N/A, hr = 0x80070002
Signed By: N/A, hr = 0x80070002
Product Name: Windows 7 Ultimate
Architecture: 0x00000009
Build lab: 7601.win7sp1_gdr.130828-1532
TTS Error:
Validation Diagnostic:
Resolution Status: N/A
Vista WgaER Data-->
ThreatID(s): N/A, hr = 0x80070002
Version: N/A, hr = 0x80070002
Windows XP Notifications Data-->
Cached Result: N/A, hr = 0x80070002
File Exists: No
Version: N/A, hr = 0x80070002
WgaTray.exe Signed By: N/A, hr = 0x80070002
WgaLogon.dll Signed By: N/A, hr = 0x80070002
OGA Notifications Data-->
Cached Result: N/A, hr = 0x80070002
Version: N/A, hr = 0x80070002
OGAExec.exe Signed By: N/A, hr = 0x80070002
OGAAddin.dll Signed By: N/A, hr = 0x80070002
OGA Data-->
Office Status: 109 N/A
OGA Version: N/A, 0x80070002
Signed By: N/A, hr = 0x80070002
Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3
Browser Data-->
Proxy settings: N/A
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
Default Browser: C:\Program Files (x86)\Mozilla Firefox\firefox.exe
Download signed ActiveX controls: Prompt
Download unsigned ActiveX controls: Disabled
Run ActiveX controls and plug-ins: Allowed
Initialize and script ActiveX controls not marked as safe: Disabled
Allow scripting of Internet Explorer Webbrowser control: Disabled
Active scripting: Allowed
Script ActiveX controls marked as safe for scripting: Allowed
File Scan Data-->
Other data-->
Office Details: <GenuineResults><MachineData><UGUID>{58492533-DAC0-4F4B-8CB4-7C2572CD6AD2}</UGUID><Version>1.9.0027.0</Version><OS>6.1.7601.2.00010100.1.0.001</OS><Architecture>x64</Architecture><PKey>*****-*****-*****-*****-P4K27</PKey><PID>00426-OEM-8992662-00400</PID><PIDType>2</PIDType><SID>S-1-5-21-3905371182-2698555194-554347162</SID><SYSTEM><Manufacturer>Dell
Inc.</Manufacturer><Model>Latitude E6520</Model></SYSTEM><BIOS><Manufacturer>Dell Inc.</Manufacturer><Version>A18</Version><SMBIOSVersion major="2" minor="6"/><Date>20130628000000.000000+000</Date></BIOS><HWID>A05B3107018400FE</HWID><UserLCID>0809</UserLCID><SystemLCID>0409</SystemLCID><TimeZone>GMT
Standard Time(GMT+00:00)</TimeZone><iJoin>0</iJoin><SBID><stat>3</stat><msppid></msppid><name></name><model></model></SBID><OEM><OEMID>DELL </OEMID><OEMTableID>CBX3
</OEMTableID></OEM><GANotification/></MachineData><Software><Office><Result>109</Result><Products/><Applications/></Office></Software></GenuineResults>
Spsys.log Content: 0x80070002
Licensing Data-->
Software licensing service version: 6.1.7601.17514
Name: Windows(R) 7, Ultimate edition
Description: Windows Operating System - Windows(R) 7, OEM_SLP channel
Activation ID: 7cfd4696-69a9-4af7-af36-ff3d12b6b6c8
Application ID: 55c92734-d682-4d71-983e-d6ec3f16059f
Extended PID: 00426-00178-926-600400-02-2057-7601.0000-0452014
Installation ID: 015022194896715926564380852615762536846771772141316646
Processor Certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338
Machine Certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339
Use License URL: http://go.microsoft.com/fwlink/?LinkID=88341
Product Key Certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340
Partial Product Key: P4K27
License Status: Initial grace period
Time remaining: 37860 minute(s) (26 day(s))
Remaining Windows rearm count: 3
Trusted time: 14/02/2014 09:02:26
Windows Activation Technologies-->
HrOffline: 0x00000000
HrOnline: 0x00000000
HealthStatus: 0x0000000000000000
Event Time Stamp: 2:14:2014 09:00
ActiveX: Registered, Version: 7.1.7600.16395
Admin Service: Registered, Version: 7.1.7600.16395
HealthStatus Bitmask Output:
HWID Data-->
HWID Hash Current: NAAAAAEAAQABAAIAAAACAAAABAABAAEAHKLYsxuJLAK4jqbIhjvuI1YXxgem9B73it4ucw==
OEM Activation 1.0 Data-->
N/A
OEM Activation 2.0 Data-->
BIOS valid for OA 2.0: yes
Windows marker version: 0x20001
OEMID and OEMTableID Consistent: yes
BIOS Information:
ACPI Table Name   OEMID Value   OEMTableID Value
APIC           DELL         CBX3
FACP           DELL         CBX3
HPET           A M I        PCHHPET
BOOT           DELL         CBX3
MCFG           DELL         SNDYBRDG
TCPA
SSDT           DELLTP       TPM
SSDT           DELLTP       TPM
SSDT           DELLTP       TPM
DMAR           INTEL        SNB
SLIC           DELL         CBX3
SSDT           DELLTP       TPM

Hi,
The error code 0xC004E003 means that the Software Licensing Service reported that license evaluation failed.
We may need to involve the phone activation center and check if they can resolve the issue:
How to contact a Microsoft Product Activation Center by telephone
http://support.microsoft.com/kb/950929/
Meanwhile, you should post your question in the forum mentioned by Kamin of Ressik. They are the most knowledgeable about the topic.
Hope it helps.
Regards,
Blair Deng
Blair Deng
TechNet Community Support

SG500X Boot Code Update fails (Boot Code too old)

Hi,
I wanted to add an SG500X to an existing stack (Native stacked pure SG500X-Stack) and it always fails, all LEDs on, System LED blinking Amber (according to the Admin Guide this is Hardware failure).
The eventlog on the Switch says, that boot code upgrade failed to deploy on the new stack unit.
I tried manually to upgrade the boot Code to the version of the Stack, but it always fails with the error "Boot Code too old".
Current Version is 1.2.0 and I want to upgrade to 1.3.0.03, in the download portal there are no versions between that.
How can I get this Switch working with the stack?
Regards,
Chris

Managed to get this working: Switched back over to image 1 (1.2.9) and updated the boot code, worked like a charm.
Then switched back to image 2 (1.3.5).
Didn't try to add this unit to stack for now, but I think it'll work for now

LOGGING IN FAILED DUE TO ERROR

Computer will not let me log in because it gives a logging in failed due to error message.

Hello Alison,
If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.
If that doesn't help Reinstall the OS.

All Windows I Install return boot\bcd error

Have a l645d-s4040.
Im Lost now.. I've read many threads similar to my problem, or exactly like my problem. Ive tried it all, and done at least 12 Different installs. heres the info:
Bought it brand new, was unaware of making the restoration disks until it was too late.
I had a virus, so I did "clean all" in diskpart, at the cmd prompt. So i can start fresh. I have a retail version of Windows 7 Home Premium 64 bit, which was the original OS. went through the installation process fine, until the reboot where its supposed to go through the second step of the installation. on reboot i get a "bcd\boot" error. Ive tried repairing the MBR, the Boot record, ive tried using align=1024, ive tried using paragon, and acronis to fix the boot record. Ive tried using boot managers. Ive tried installing windows vista, ive tried windows 7 ultimate 64 and 32 bit versions.. the only OS i can get to install is XP.. Im at a loss
of course of done : Startup Repair (http://www.sevenforums.com/tutorials/681-startup-repair.html)
So after the first step of of installation, which goes fine then reboots to continue the installation i get:
Windows Boot Manager
Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
1. Insert your Windows installation disc and restart your computer.
2. Choose your language settings, and then click “Next.”
3. Click “Repair your computer.”
If you do not have this disc, contact your system administrator or computer manufacturer for assistance.
File: \Boot\BCD
Status: 0xc000000f
Info: An error occurred while attempting to read the boot configurations data.
Enter= Continue ESC=Exit
so i reboot with the install cd. which i downloaded from www.mydigitallife.info/windows-7-iso-x86-and-x64-official-direct- download-links-ultimate-professional-and-home-premium/.
And ran the startup repair, first time no OS found and failed to save startup options. rebooted and this time the repair worked and it booted fine running the 2nd step of the installation process.. on the reboot i got same boot\bcd error.. so i repeated the repair steps above.. it finally booted and finalized the installation.. i got to the desktop fine and installed all my drivers. when i rebooted i got the same error.
WHATS UP WITH THIS???

Satellite L645D-S4040
I would restore the hard disk to its original out-of-the-box contents using Toshiba recovery media, which you can obtain from Toshiba.
Order Toshiba Recovery Media
-Jerry

Installation Succeeded but Patch Failed. Download Error Support (49)

Installation Succeeded but Patch Failed. Download Error contact Support (49)

i have the exact error. I have CC for Photographer for quite some times now and it updates on and off normally until perhaps a couple of month ago. Lr updated ok. ACR updated ok. But Ps ended up with such error. I uninstall it and tried again, same error. There was one hit that mention about disabling McAfee anti-virus. Since my machine is managed by my company, I can only disable it by booting Windows (Win 7 enterprise) in Safe Mode. I did but the same error. Any other suggestion?
By the way, my other machine which I install exactly the same CC applications have no problems at all so I am quite sure it is my company machine that is causing the problem. I just need to figure out what is wrong.

Partition failed with the error: The target Core Storage volume is locked

partition failed with the error: The target Core Storage volume is locked
Hello everybody!
Please help me.
I'm using MacBook Pro (Retina, 13-inch, Mid 2014), Processer:2.6 GHz Intel Core i5, Memory: 8 GB 1600 MHz DDR3.
my computer i have divided in 3 drives: 1-Machintosh HD (Mac OS) 2-Bootcamp (Window OS) & 3-Data (drive for data storage).
I don't want to use Window OS on my computer anymore so I decided to delete drive Data (the third drive) & Window OS (the second drive).
I want my hard drive become a single drive back but when I was formatting, there were some problem display:
then i clicked ok and it displayed like this:
then i try to format or create new partition, it's nothing happen when press button apply.
my computer has storage space 256GB but now when it is happened like this my storage space is only 127GB only.
so please help me.. what so I do with this problem.
Thank you.!

arajs wrote:
I used Boot Camp Assistant (for instaling Windows XP) and there was Partition error:
+*The disc cannot be partioned because some files cannot be moved.*+
+Back up the disk and use Disk Utility to format it as a single Mac OS Extended (journaled) volume. Restore your information to the disk and try using Boot Camp Assistand again.+
so I tried Yasu, verified permission, verified disk, and everything was ok, but in Disk Utility I was trying to split or change size of my disk but there is one error again:
+*Partition failed.*+
+Partition failed with the error: No space left on device+
but I have 64GB free space!
how must I "+Restore your information to the disk+" or what else can I do?
thanks!
This is a standard error message.
If you would have checked into the bootcamp forum you would have instantly found the solution.
http://discussions.apple.com/forum.jspa?forumID=1244&start=0
All that error message means is that you do not have enough conguous disk space available. No big deal at all for an older system. You have bits of files strewn over the "free space."
The solution as you would find in the bootcamp forum is to clone your HD, using a file-file clone, then test the clone to be sure it is working and then to erase your HD and clone back.
Works every time.
Message was edited by: Theodore

MSFC boot NVRAM error

Hi, after reloading a Catalyst 6009, MSFC2 boots in ROMmon. I've tried to boot the image from rommon but i receive the following message:
"Environment checksum in NVRAM failed.
Bus Error exception"
What does it mean?
What can i do?
does it look a hardware or software error?
Thanks

Hello,
This looks like a corrupted nvram, I'm afraid there is little you can do from rommon. In your case it seems that it can't even read the environment variable and the device won't boot without it. I agree that usually this is highlighting a bad hardware, see TAC Case collection (unfortunately you won't have access to IOS CLI as suggested there):
https://www.ciscotaccc.com/kaidara-advisor/core/showcase?case=K10149421

Disk Erase failed with the error- Operation timed out

I've checked my computer- Mac Book White in Apple store, everything is fine just the hard disk has been corrupted. Needed to erase and reinstall. By the time I wanted to erase it, I can't erase and appears "Disk Erase failed with the error- Operation timed out".
Anyone knows how to solve this question would be nice.
Thanks

Well give this a try:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Now download a utility like TinkerTool System or Leopard Cache Cleaner - VersionTracker or MacUpdate - and use it to clear out your system, user, and font caches.
And, try this for the software update issue:
Fix for Software Update
See Troubleshooting Automatic Software Update in Mac OS X.
Delete the following files:
/Library/Preferences/com.apple.SoftwareUpdate.plist
/Home/Library/Preferences/com.apple.SoftwareUpdate.plist
/Home/Library/Preferences/ByHost/com.apple.SoftwareUpdate.xxx.plist
"xxx" is a number.
/Home/Library/Caches/com.apple.SoftwareUpdate/ (delete entire folder)

NTDETECT FAILED boot up error??

Similar Messages

Maybe you are looking for