Num Lock Light Indication

Hello,           I just bought HP Pavilion Notebook - 15-p212nx, which seems very nice but I did'nt find the Num Lock Indication. I have checked also some forums and the only solution is to go for third party solution providers like Tray Status.  Is there any other way to have a num lock indication same like LIGHT. if not then how HP neglect such an important function.  Thanks in advance.  Regards Umair 

Hi  ,
Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your Looking at your manual  page 11, for your Notebook shows me that the keypad function that is active when the computer is turned off is reinstated when the computer is turned back on. This is the design of the Notebook. There is no light for this function as per the design. Thanks.  

Similar Messages

  • HP Laptop. Blank screen and caps and num lock lights flashing.

    Hi,
    I hope you can help me.
    My laptop is the HP Pavilion DV6-1216sa, bought new in September 2009. When I turn it on, I get a blank screen, the fan is working and the wifi, volume and mute lights light up. The caps lock and num lock lights flash together, once everyone 3 or 4 seconds. Normally when this happens (it has happened throughout the life of the laptop), I turn it off and turn it back on, and it works again. However this time, the problem persists. I've tried most combinations to get the bios screen up and I've tried getting it to another screen via hdmi and VGA, but no signal received. I have tried everything recommended by the HP support website. I have checked the battery, ram, and hard drive.
    Best regards,
    Jay

     The best cheapest fix is if you can remove the motherboard your self and send it to a refabricator who will check all the chips on the motherboard and reball the bad ones. Cost is about $60-120, closer to the bottom if you can ship them just the board but if necessary they will take the whole laptop and remove the board for you. 
    eBay auction for repair motherboard only
    disassembly included auction
    If this is "the Answer" please click "Accept as Solution" to help others find it. 

  • HP Pavillion dv6446 caps/num lock lights won't light

    i had my laptop screen replaced and when i got it back the caps lock/num lock lights wern't working. i took it back to the guy who fixed it and he told me it he couldn't replace the LED's because they needed to be replaced and he didn't know how to replace LED's mounted to the motherboard. i found it a bit funny that both LED's blew at the exact same time, especially since i had several other problems that appeared after he replaced the screen (those problems have since been fixed by myself). is there some controller that has been messed with that would cause the LED's to not light up?

    I am facing the same problem with my dv6500 and never had a so big issue as yours. I believe leds are ok (when I press "fn" + num lock) this led lights up. I would really appreciate a help from HP in this issue.

  • DV4 flashing caps lock and num lock lights

    My laptop, an HP Pavilion DV4-2040US, has stopped booting up recently. The day before this problem come about I was using the laptop perfectly fine. I then went one day without using. When I turn on the laptop it booted up but nothing showed up on the screen. Then the CAPS LOCK and NUM LOCK lights started to blink on and off.
    I did some researching about the blinking lights and what they mean but I don't think mine is listed on there. It says the pattern will repeat a couple of times then shut off, but mine doesn't. The pattern is the CAPS LOCK and NUM LOCK both blink once every 3 seconds (about) and keeps blinking every 3 seconds forever. The only time they stop blinking is when I shut I down by holding the power button on the laptop.
    I've tried disconnecting everything and holding for 15 seconds and even tried holding it for 30 seconds and that still didn't fix the problem. I called HP support and the guy who I talked to told me it sounded like a motherboard issue, but he wasn't sure exactly and told me to ask here for help.
    If it matters, I can hear the fan turn on for about 2 seconds then stop. Also all the touch sensitive buttons light up too$

    Please, someone, anyone help me. I am having this exact same problem as we speak It happened after i put the laptop to sleep overnight. The LEDs for capslock and numlock blink consistently but slowly-approximatelt 2-3 seconds. When started up, i hear the fan come on for maybe a second or two and then comes off.I've tried all the mentioned solutions - i removed the battery for a while and put it back in-i tried the four arrows-i tried started up with AC adapted but without battery - and still no fix. What i am worried about is the documents and files on the laptop. Are they recoverable? Please help me on this someone. Please. Thank You.

  • DV9702ea - Win7 - Num Lock LIGHT not working

    Hi guys
    I have upgraded to Win7 and after installing the ill fated "Coprocessor" driver I am now battling with the last issue:
    My Num Lock light is not working, the key works fine, I can work fine with numerical pad and all those keys there its just the light that does not come on.
    I have installed all the drivers for Vista from HP site and still nothing.
    Any ideas? Thanks guys.
    Maelito 

    Hello F1503,
    Welcome to the HP Forums, I hope you enjoy your experience! 
    I have read your post on how the light on the num lock key of your notebook is not illuminating, and I would be happy to assist you!
    To enable the light on the num lock key, I recommend following this document on Some Function Keys or Keyboard Shortcuts Do Not Work Correctly with Windows 7. This resource should help provide a hotfix for your num lock key.
    For further assistance, I will need to know:
    If your computer has completed all of its important Windows Updates.
    If you have updated your HP drivers using the HP Support Assistant.
    If this is an on-going, or recent issue.
    Please re-post with the results of your troubleshooting, and I look forward to your reply!
    Regards  
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Num lock light not working

    Hi,
    I have a HP dv7-3060US, Prod.#VM237UA#ABA.  Running windows 7 home ed.
    My num lock light does not come on.  The num lock key is working.
    Is there a way to get the num lock light to work?
    thanks

    Hello F1503,
    Welcome to the HP Forums, I hope you enjoy your experience! 
    I have read your post on how the light on the num lock key of your notebook is not illuminating, and I would be happy to assist you!
    To enable the light on the num lock key, I recommend following this document on Some Function Keys or Keyboard Shortcuts Do Not Work Correctly with Windows 7. This resource should help provide a hotfix for your num lock key.
    For further assistance, I will need to know:
    If your computer has completed all of its important Windows Updates.
    If you have updated your HP drivers using the HP Support Assistant.
    If this is an on-going, or recent issue.
    Please re-post with the results of your troubleshooting, and I look forward to your reply!
    Regards  
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Pavilion dv7-1245dx caps light and num lock light blink

    Got a Hp pavilion dv7-1245dx. When going to start the computer after hitting the power button the all the lights come on on the volume bar, the fan runs and then the caps light and the num lock light start blinking. I can tell if there is a specific number of blinks in a sequence or if it is just one blink repeatedly.  This computer is less than 2 yrs old. Please help

    I have already tried all the powering down options and nothing is helping. I really need this thing!

  • Num lock light keeps flashing

    Hi,
    I have Lenovo 560 and since few days I am observing a strange problem.. The num lock on keypad keeps toggling itself and the num lock light keeps flashing.. ?i dnt know whats the problem is.. any body faced similar problem?
    please help.
    Thanks,
    Rajan

    I don't think it is serious enough to return it. I have problems with my num lock and caps lock keys also, but I think it is a problem with the PMU firmware. Quite a few people are having an issue, so I don't think it is a hardware problem.
    There are also people having other problems related to the PMU, such as the coloured lines at startup. I suspect we will see a firmware update at some point that can hopefully fix it.
    My advice would be try resetting your PRAM with command-option-p-r at startup (until you hear the second chime). Or resetting the PMU by turning off the 'book. disconnecting power and taking battery out, then pressing power button for 5 seconds. Then turn it all back on again and it should be ok.
    Stay away from 10.4.7 too, it's just trouble.

  • CAPS & Num Lock Lights

    Hi,
    It is the second time that this happens to me; I switched on my MacBook, and the number lock light and CAPS light turn on too. By keeping them on, they work as if they were off. While if i turned them off, they work as if they were on.
    To resolve the problem i restart my mac, and everything goes back to normal..
    Does anyone have the same problem or a solution to this?
    Thank you all!
    Regards
    Val

    Well...I have to say that if it wasn't happening to my MacBook RIGHT NOW, I wouldn't belive you. As I'm typing now, BOTH caps lock and num lock lights ARE ON! If I hit the shift key, I do get caps.
    I JUST SHUT OFF THE CAPS LOCK LIGHT AND NOW ALL I GET ARE CAPS...EVEN WHEN I PRESS THE SHIFT KEY AS I"M DOING NOW.
    123456789 Both lights are on as I type now, but when I shut off the num lock, all I could get on the keyboard were the number pad numbers as I typed at the beginning of this sentence.
    With both lights off, again, all I get are the keypad numbers...no letters.
    The MacBook was working fine earlier today. I just booted it up and it started with this weird behavior. I hope rebooting fixes it.
    ~Rick

  • Blinking caps and num lock lights

    Opened up the lid on sleeping laptop and had nothing but a blank screen and blinking caps and num lock lights. I finally got vista restarted after turning it off and on a couple of times. Everything seems to be working, however the caps and num lock lights are still blinking every 2 seconds. Any thoughts on what is causing this?
    JRG
    HP Pavilion Dv4

    Hello,
    The blinking caps and numlock are a diagnostic feature of the Dv7 Notebook ( and others ). Depending on the combination it can be a number of different symptoms. They can be as minor as the battery having an insuficient charge or as serious as a CPU failure. I would recommend updating the ROM BIOS on your unit to ensure you have the latest fixes.- Make sure you have the latest one for your model - Here is a link to a document on the Blink Codes.
     http://h10025.www1.hp.com/ewfrf/wc/document?docnam​e=c01443366&cc=us&dlc=en&lc=en&jumpid=reg_R1002_US​...
    regards,
    I am an HP employee.
    "Did my response help with your issue? If so, please give me Kudos by clicking the "Kudos" button or mark the post that solved your problem as the Accepted Solution. Thanks!"

  • Replaced keyboard and now the caps lock light and num lock light are blinking and no screen???

    I just replaced my keyboard on my HP DV6-2155DX Laptop and got it all back together and now there is no display on the screen and the caps lock light that indicated that caps lock is on and the num lock indicator light are both flashing. any help and all??? thanks you

    Ouch, doesn't sound good, but...
    Have you done a PRAM reset, CMD+Option+p+r...
    http://support.apple.com/kb/HT1379
    In fact, do 3 in a row, takes a bit of time.
    Intel-based Macs: Resetting the System Management Controller (SMC)...
    http://support.apple.com/kb/HT3964

  • HP Pavilion tx2500 - Caps Lock and Num Lock lights blink once

    I turn on my HP Pavilion tx2500 and I hear the fan spinning but nothing else happens.  The lights next to the Caps Lock and above the Num Lock keys blink (a repeating single blink).  According to some HP technical support documents I found online, the repeating single blink indicates a CPU problem.  My laptop is out of warranty and the $400 to send it to HP to have it fixed is practically the same price I paid for the laptop 2 years ago. 
    Do the blinking lights mean the CPU is fried?  And is there anything I can do to fix the laptop?
    Thanks,
    -Jeff
    This question was solved.
    View Solution.

    I have the same problem. I called HP they said the same thing. But, I am BIOS engineer myself and has worked with lot of motherboards, So I felt there is no point in sending a 399$ to find what happend and on top of that fixing charges.
    I noticed the problem started when I installed Win 7 Ultimate edition to the board and let tbe board Idle for a long time and it went into sleep mode and when I hit the button for resume it would not resume, the blinking started.
    I have seen the same thing happend to my friend laptop, luckily for him it recovered and he removed the Sleep Option. SO his laptop is shutdown or running in full power.
    I thought this is not coincidence, there is defenitely a bug in HW or SW that is causing it. remove battery. I replaced the memory and removed the cmos battery and left for a long time (short the battery terminals to discharge quickly). Then I rebooted the machine, Luckuly for me it went to windows, I tht of replacing the BIOS firmware, bcos they ahve some latest on by that time I had a visitor and I was talking to him the system went into sleep mode and will never recover. The system started blinking. I dont see this as a CPU problem.
    I still evaluating this. I will try to post my findings. I have aclip to read the BIOS chip but everytime i get different read. SO I am planning to remove the BIOS chip and put a socket so that I can play with the BIOS.

  • Num lock light

    Hello everyone.
    After I updated the bios from my P6N SLi Platinum to version 1.5, my num lock won't go off when I shut the pc down.
    I've looked through my bios but I can't seem to make it go off when I shutdown
    I've also tried removing the OC from the CPU and loaded default settings but it still stays on after shutdown.
    Does anyone have any suggetions.
    My specs are below
    Thx for your help

    I completly shutdown.
    S3 is enabled in BIOS, set it to s1, doesn't make a difference.
    I'm pretty confused now 
    If I choose to not boot up num lock it's out, but when system is shutdown I still can turn it on and off 

  • Num Lock light flickers intermittently

    Hey, all! I have an L555-s7008 laptop computer. Windows 7, 1TB HDD, 8GB RAM, Intel Core i5 430M clocked at 2.2 Ghz
    I have been attempting to solve an issue with my laptop for a few months now, and I am at a loss. I got it from a friend, and when I got it, the keyboard needed replaced. The keys were ripped off. Also needed new speakers. I upgraded the hard drive and RAM to the maximum capacity. The previous owner had no issues with it, except it was unable to recognized the DVD drive, and the installation was ridden with viruses. Well, after a fresh install of the OS and drivers on the new hard drive, I am still having some issues. Every now and then, the number lock light on the keyboard will have a blinking fit, and eventually turn off, however the keypad will still work. During DVD playback in media center and it happens, you can hear dinging coming from Windows, like what happens when you press multiple keys at a time and hold them. It's annoying. I also had problems with the original DVD drive, so I swapped it out, and the problem seems smoother, but the dinging and blinking of the number lock light continues. I know this post is quite lengthy, but I thought I would get all the details. Thanks in advance for the help!

    I actually have this issue as well, and also just press it a few times to fix the issue.
    It hasn't been a big problem for me, and I'm not very bothered. You may want to check your bios for numlock settings and see if that may be causing you an issue before jumping at X being the culprit (not saying it isn't).

  • Num Lock light stays on after shut down

    Hi, I've just put this system together and I've noticed that the num locks occasionally stays on after I shut down the PC.
    I've changed the power supply to the one below and the problem continues.
    I have my keyboard plugged into the USB port nearest the the old style PS 2 Keyboard port on the rear of the PC
    MOBO FM2 A75MA E35         Bios E7721AMS      V2.2
    Processor:    AMD A6 6400K Dual Core
    Memory 1 stick of  8 gig Crucial memory   # CT10246BA1339
    HD   Kingston  SSD  120GB
    Burner   HP 24X DVD
    PS Antec BP350  350 Watt
    Keytronic Keyoard
    Logitech Mouse
    Samsung Monitor
    Win Pro SP1
    Please help.....

    It's this one:
    Quote from: kmax2 on 02-December-13, 21:42:47
    BIOS Power Management and EPU2103 was disabled. I still have the problem.
    Quote
    If I take the battery out and put it back in then would that clear the CMOS?
    Remove power cord, then clear the CMOS by jumper or button,
    i thought you already done this.
    See here for guide: >>Clear CMOS Guide<<
    Quote
    What does BIOS update with EC mean? I know what a BIOS update is but what does EC mean?
    They probably mean to update BIOS with proper parameters to include addiction ROM holes.
    You can ask them for clarify about this, which BIOS you should update and what exact flash command line options to use.
    Quote
    What should I try first?
    Try Clear Cmos 1st,
    then try to Enable EUP [but it should be already enabled after clear cmos]
    but double checking,
    else ask them back about BIOS & EC flashing clarify

Maybe you are looking for