Number range for object AUFTRAG

Hello,
we have in number range group Ztest but fot this group there is number range number missing.
Problem is when i click on ztest group and go to Interval maintain it does not allow me to put the new number range.
I dont want to deleted the exsisting Ztest group and redifne it.
Regards,

Hi Yusuf,
You have posted this under SAP Community Network Forums » SAP NetWeaver » SAP NetWeaver Platform .
Please post it under ABAP General. You will get more answers there.
Also, please have a look at Note 52390 - Transport of number ranges with group.
Regards
Prasenjit

Similar Messages

  • Internal number assignment for object AUFTRAG

    Hello,
    Previously with SAP PM module we had configured the maintenance work order number range for internal assignment to a narrow range of numbers i.e. 12000000 to 12999999.
    Following rolling out the functionality to other sites, we required to extend the internal number range (to accomodate the volume to be produced) and have updated this in configuration i.e. 300,000,000,000 to 399,999,999,999.
    We are now experiencing an information message each time we Save a new maintenance work order;
    Internal number assignment for object AUFTRAG (numbers are in critical area)
    Message no.  RU 153
    When the user clicks Enter to continue a warning message is also displayed on the status bar;
    Number XXXXXX for order type XXX within critical area
    Message no. CO 395
    However, we have investigated this and the work orders are creating normally after this. We have created in the system, the work orders with the prevous number range and also hunders of work orders with the new number range, we do not appear to be experiencing our buffer.
    I have check the settings in SNRO config setting. The settings appear as standard with a warning buffer of 5% and the No. of numbers in buffer = 20.
    Please can anyone advise how to remove this information message or how to update the system to resolve.
    Regards,
    Hayley

    The message is given by the number range function, according to the configuration of field percentage. You have entered 5% - which means when you reach within 5% of the end of the numbers, you should get the warning. Your range is 300,000,000,000 to 399,999,999,999 My calculation that you should get the warning around 395,000,000,000
    I suspect that the issue is linked to buffering of the numbers. Is it resolved??

  • Excise Number Range for Object J_1IEXCLOC

    Dear All ,
    I am having one issue regarding excise number range for object J_1IEXCLOC and sales group : 41 Domestic. i have already maintained number range for 2009 is 0000000001 to 0000000300. Now the range is exceed and the new excise invoice is created with number 0000000001. Now i am confused if i will maintain range upto 0000000500 for 2009 then what will be the new  invoice number, whether it will be 0000000002 or 0000000301.
    Pls. Give me some suggestion, What should i do now for the number range to be in continuation.
    Regards,
    Swapnil Vaidya

    >
    swapnil vaidya wrote:
    > Dear All ,
    >
    > I am having one issue regarding excise number range for object J_1IEXCLOC and sales group : 41 Domestic. i have already maintained number range for 2009 is 0000000001 to 0000000300. Now the range is exceed and the new excise invoice is created with number 0000000001. Now i am confused if i will maintain range upto 0000000500 for 2009 then what will be the new  invoice number, whether it will be 0000000002 or 0000000301.
    >
    > Pls. Give me some suggestion, What should i do now for the number range to be in continuation.
    >
    > Regards,
    >
    > Swapnil Vaidya
    It will be 2 and not 301. This is a flaw with CIN. All transactions take place by means of internal numbers and are stored in CIN transaction tables. Hence when the range gets exhausted, the number gets reset to the beginning, yet there is no error because internal number, which is the primary key, is different.
    To solve your problem. Go to SNRO and provide the object J_1IEXCLOC and click on status. Change the status to 300 and continue with your transaction.
    Regards,
    Aroop
    PS: Your question is more relevant for SD than MM.

  • Error: Number range  for object RESB does not exist

    Hi
    I'm trying to convert a planned order (to purch requisition) partially via trxn code MD04. Upon saving I get the above error msg. The complete text of msg is as  follows. I've maitained the number ranges of all the objects specified in this error msg. Can somebody explain on how to overcome this problem?
    Many thanks
    BE
    Error Msg Text:
    Number range  for object RESB does not exist
         Message no. 61501
    Diagnosis
         The system cannot create a document for an MRP element if no number
         range or interval has been maintained in Customizing of MRP or if t
         number range you have maintained is not allowed.
         Below is a list of MRP elements that are affected:
         Number range object  MRP element
         PLAF                 planned order (operative oder simulative)
         EBAN                 purchase requisition
         RESB                 dependent requirements
         MDSM                 simulative dependent reqmts (long-term plannin
         MDTB                 MRP list
    Procedure
         Check the number ranges in Customizing. If you do not have the necessa
         authorization, please get in touch with your systems administration.

    Hi
    Thanks for the reply. But I have maintained the number ranges for matl. reservations/dependant requirements at OMI2. Here is the screen shot..Do find anything wrong with it? Pl advice.
    NR Object                             MRES/DREQ
    No.                          From Number            To Number          Curr Number          Ext
    01                           0000000001               8999999999           380                    blank
    02                           9000000000               9500000000           blank                  checked
    RB                          9500000001               9999999999           blank                  checked
    Number ranges for the plants are assigned to 01 (0000000001 to 8999999999).
    thanks
    BE
    Edited by: Brian Elfie on Jan 10, 2008 11:27 AM

  • Number range  for object MDTB does not exist - Message no. 61501

    Hi All ,
      I have done the necessary configurations in PP say
    Order Type
    Order Type Dependent Parameters
    Scheduling parameters for planned & production order
    Confirmation parameters
    Availabilty check etc
    and iam able to create planned & production order and confirma the production order.
    I want to configure for MRP: -
    Settings done are
    Have activeted planning file entry for all plants.
    When i run MRP system throws a error <b>Number range  for object MDTB does not exist - Message no.61501 </b>
    Is there anything to do with plant parameters OPPQ and Mrp Group OPPR.
    I just tried plant parameters,standard 0001 is not available for copying.
    Suggest me how to proceed to set MRP.
    Shankar

    Hi shankar
      it is a good practice while creating the plant copying the plant from the standard plant so that all the standard table enteries will be copied  for the plant as the standard plant is not there youcan think of copying from any other plant similar to your plant which has the required entry. else
    in SE16N  check the NRIV table for the Object MDTB. if enteris found then make the table entry with the help of abaper.
    hope this helps
    regards
    SK

  • Number range  for object BANF does not exist

    Hi Guru's
    I have been trying to convert the Planned orders to Purchase requisition and unfortunately the system consistantly giving me the error as reflected below  despite changing the numbering range on the affectred documents. Please help.
    Number range  for object BANF does not exist
    Message no. 61501
    Diagnosis
    The system cannot create a document for an MRP element if no number range or interval has been maintained in Customizing of MRP or if the number range you have maintained is not allowed.
    Below is a list of MRP elements that are affected:
    Number range object MRP element
    PLAF planned order (operative oder simulative)
    EBAN purchase requisition
    RESB dependent requirements
    MDSM simulative dependent reqmts (long-term planning)
    MDTB MRP list

    Hello,
    You can define number range for Purchase requistions in OMH7 transaction agaist each number range number and you assign can assign these number range number to your purchase requistion document types in SPRP >> Materials management >> Purchasing >> Purchase requistion >>Define doucment type.
    E.g for NB doc type number range number is 20
    and in OMH7 number range number 20  has interval from- 2000000000 to 2099999999
    same way
    for RV doc type number range number is 21
    and in OMH7 number range number 21  has interval from- 2100000000 to 2199999999
    Regards,
    Shailesh

  • Alphanumeric number range for object QMERKRUECK

    Hi all
    I have raised a question on number range object QMERKRUECK few days back.
    Internal number assignment for object QMERKRUECK (numbers are in critical area)
    With reference to the same please let me clear, if it is possible to create alpha numeric number range for the same object.
    I tried in SNRO but system does not allow for this.Next is , if any userexits are there to achieve this.
    I know, this issue is hardly seen in any implementation but if anybody has gone through this and got a proper solution, please share your experience.
    Regards
    D Mohanty

    Hello,
    You can define number range for Purchase requistions in OMH7 transaction agaist each number range number and you assign can assign these number range number to your purchase requistion document types in SPRP >> Materials management >> Purchasing >> Purchase requistion >>Define doucment type.
    E.g for NB doc type number range number is 20
    and in OMH7 number range number 20  has interval from- 2000000000 to 2099999999
    same way
    for RV doc type number range number is 21
    and in OMH7 number range number 21  has interval from- 2100000000 to 2199999999
    Regards,
    Shailesh

  • Number range for Object (Organizational unit, Job, Position)

    Hi all,
    How to maintain number range for Organizational unit or Job or Position by Company Code or PA, EG, ...?
    Thanks,
    Quang

    Hi,
    For organizational objects maintain number ranges via OONR.
    e.g. In order to maintain number range for C - Job object in plan version 01 add the following line to OONR:
    01C  IN  EX
    Then select this line and hit "Number range maintenance"
    There create the interval you want.
    (EX 60000000 69999999)
    For PA, EG there is no number range maintained.
    Regards,
    Dilek
    Edited by: Dilek Ersoz Adak on Jan 14, 2010 8:08 AM

  • Creation of Unique Number Ranges for Organizational Objects

    Hi Gurus,
    As per our client's requirements, We need to create unique number ranges for Organizational Objects such as O,S,P to distinguish based on the Object ID. Could you please help me out to create the same.
    And also to create unique number ranges for Personnel Development Objects such as QK & Q.
    Thanks in Advance
    Regards
    Vinoth Kumar.R

    Hi,
    To maintain object specific number ranges, go to customising node Personnel management --> Org. management --> Basic settings --> Number range manitenance --> Maintain Number ranges
    Here there will already be a default entry as $$$$.
    To create different range for object say O you can use the following options:
    Create entry as $$O - number range applicable to all Org units across all plan versions.
    Create entry as 01O - number range applicable to all Org units under plan version "01"
    Then under Interval maintenance create the desired number ranges under IN for internal or EX for external (check the external tick box for external number ranges)
    In the similar manner you can create the number ranges for objects C, S , Q & QK.
    Hope this is helpful.
    Regards,
    Shreyasi.

  • Internal number assignment for object

    Hi Experts,
    While creating PM order the error comes"Internal number assignment for object AUFTRAG"(numbers are in critical area).
    I am not able to create order.
    Please help.
    Regards
    Vishal

    Hi Vishal
    Your number range might have exhausted, you need to extend it through T-code SNRO. number range object (AUFTRAG). click numbr range button then change interval & extend the to number
    shakti

  • Change in number range for Job Family

    Hi,
    We have a requirement where we need to change the existing number range for object type Job Family.
    The number range begins from 500* series. Now this needs to be changed to 90000000 number range.
    Now the question is what would be the impact if we delimit the objects with earlier JF number range and
    create the job families as part of the job catalogue with 90000000 number range.

    Hello,
    Only difference/impact is you will get new number ranges only.
    regards

  • Different Number range for different objects

    HI Gurus
    Could you please explain how can we make different Number range for different objects(O,S,P).Can we do with standards or we can go for UserExit??.
    Your early Advise will be appreciated.
    Thanks
    Chandra

    Hi Chandra,
    SM31 -> T77IV : 01S -> Number Range Maintenance.
    (or SPRO -> Pers Man -> Org Man -> Basic Settings -> Maintain Number Ranges)
    For the subgroups
    01C (plan variant 01, Object type C) Job
    01O (plan variant 01, Object type O) Org unit
    01S (plan variant 01, Object type S) Position
    Define the following number ranges respectively.
    (EX 60000000 69999999)
    (EX 70000000 79999999)
    (EX 80000000 89999999)
    Regards,
    Dilek

  • Number range for rental object

    rental object type rs and ps use the same number range ?Can  I  distribute the diffierent number range for the different type?

    Dear Pan,
    PS/RS/RU are called RO in RE-FX and use the same number range, however you can use BAdi to assign the required number to PS or RS.
    RECACUST--> Master Data --> Usage View --> Rental Object--> Implement Enhancements (BAdI) --> Number Assignment, Validation, Substitution.
    Kind regards,
    Kishore

  • How to create number range for custom object

    Hi all,
    I want to create number range for custom object or custom tables
    Thanks
    Hemalatha

    Hi,
       Thanks, I am able to create a number range for custom object through SNRO tcode.
    Thanks
    Hemalatha

  • Set Up number range for OM Objects

    Hi All,
    I have set up Ext number range for Org Unit & Position.
    example: Org Unit 50000000 - 599999999 and i have uploaded data till 50000999.
    so it should be update current number as 50000999.
    but in my scenario its not updating current number still is '0'
    Please help me.
    regards

    Hi Waseem
    I am agree with your reply as I am doing the same thng. Currently I am using External Number Range as I am going to upload data and later will change into Internal.
    but my question is in Number Range Maintanace in Current Number should be update automatically or not.
    Example Org Unit from 500000000 - 59999999 and we uploaded data till 50000900
    so  in Current it should show 50000900
    NO      From Number     To Number      Current Number     EXT
    EX      500000000          59999999     0
    but in my case it is showing '0' in current number
    so Please confirm me whether it should update automatically, if yes pls tell me how
    regards,

Maybe you are looking for