Nvidia Quadro card not working after 10.6.6

The software profiler shows the card but there is no output from the DVI and Premiere Pro CS5 (CUDA aware) no longer sees it being available for GPU acceleration

Solved thanks to http://discussions.apple.com/thread.jspa?threadID=2710351&tstart=15

Similar Messages

SB04100 Sound Blaster Card not working after computer rebuild

=SB0400 Sound Blaster Card not working after computer rebuildZ I did a full disk format and reinstall for a friend on a Dimension 3000, running XP SP3. There is no sound at all. Speakers are good, tested on another system. Model number on the back of the sound card is SB0400, so I assume this is an older 24 bit PCI SoundBlaster card. Although I reinstalled all drivers from Dell, I found no drivers for this. The Creative site has no listing for this model.
Computer does not seem to recognize the card. Have not opened the box yet but I assume if I were to remove and then reinstall the card it would be recognized (?) I then have to find an SB0400 driver.
Does anyone know where I can find an SB0400 driver ? Does the strategy of pulling and reinstalling the card make sense ? (I have really avoided tampering with any of the hardware on this box -- since it is not mine.)

Re: SB0400 Sound Blaster Card not working after computer rebuild? Thanks much for your response. Problem solved for now. I removed the board and then reinserted it, after which I was able to download the drivers directly. Some of my difficulty with this whole process has been ) I didn't know there was no working speaker in the computer and 2) I apparently misunderstood the BIOS settings for this. I re-set it up as an add-on board during the troubleshooting process. After loading the driver, I went back to the original setting (don't recall what it was but it was for integrated sound). The setting for integrated sound works fine, with external speakers and the new 24 bit driver. Still some noise (popping and static) but this board shares the bus with 2 other cards one of which is a wireless network card. May be a PCI latency issue but I'm reluctant to change that because the network card is a bit shaky anyway.
Everything works for now -- I'll be glad to get this particular computer out of my house !

HP 15-r033tx NVIDIA Graphics card sopped working after windows 7 encountered blue scree

It has been only five days since i purchased HP 15-r033tx laptop. NVIDIA 2gb graphics card stopped working when windos 7 OS encounterd blue screen. I re-intalled the OSand all drivers softwares and yet NVIDIA doesn't show up in control panel. What do i do?

Hi @Aashish_92
Welcome to the HP Support Forums!
I understand that you had a blue screen, and now the NVidia card is not working, after reinstalling your operating system.
I am happy to help with this. What method did you use to reinstall the operating system? Did you use system recovery?
After reinstalling the OS, did you make sure that all the system drivers were updated to the current ones from the HP support page for that notebook? HP 15-r033tx Notebook PC Drivers
You can try to use the system recovery manager to reload a factory installation.
Performing an HP System Recovery (Windows 7)
Troubleshooting HP System Recovery Problems (Windows 7)
Let me know if that helps.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Nvidia Quadro 4000 not working properly

Hi all,
I am really hoping that some one can help me with a very frustrating issue with my new Mac Pro and Nvidia Quadro 4000 card.
I purchased my Mac Pro from an Apple store and added the Quadro 4000, I need that card as it is supported by Adobe Premiere CS5 to enable the GPU acceleration. The reason I went to the store to buy instead of online was to get advice about the card as I have not used a Mac for 5 years now. I was told that they are not familiar with the card, but put it in and run alongside the ATI card.
When it arrived I put it all together, except for the Quadro 4000, and it all worked perfectly. I have 2 x 27” Cinema Displays attached. I installed production studio CS5 and then extremely carefully added the Quadro card.
Without going on about all the drama with it not working with the ATI card and then removing that and installing only the Quadro, it is not doing what I bought it to do. Adobe is not recognising the device, I have updated to version 5.0.3 of Premiere Pro, which supports this card.
I think I know what the problem is, but I have no idea how to resolve it. I put the Quadro in and then installed the drivers. My research says this is wrong (there were no instructions in the box and the read me file on the disc just said I need a specific cuda driver), so I removed it, put the ATI in and hunted down all the Cuda (Quadro stuff) files, deleted them, reinstalled drivers and reinstalled the card. No change, it drives one display and Premiere still cant see it.
I have tried to find answers on the internet, Apple are not very helpful as it was a third party item they have no training on (although purchased from Apple).
The only thing I have read is it may need to be on OS 10.6.5, I updated to 10.6.6 and/or because I installed the card before drivers. I have read that I need to sort out ‘Permissions’ but can’t find out how.
Any help would be greatly appreciated, I really need to get this thing working as I have a very expensive computer I can not use.
Thanks
Phil
Oh, one other thing, it is supposed to run two displays, one via display port and the other via DVI, but I am having no joy here either, and there seems to be no DVI male to MDP female adapter????

You are making it (sounds like to me) harder than it is.
You do not mention which ATI card, but you should use both side by side unless you have the 5870 which is using the two pci 6-pin power connectors on it.
With Mac OS people generally never need to delete drivers by hand.
ATI 57x0 and Quadro work better together. Or even ATI 4870 and GTX 285 in the past. Use the ATI for monitors and Quadro for CUDA and Mercury.
FYI for Quadro 4000 Mac Owners upgrading to 10.6.6:
Included in today's 10.6.6 related apple docs is one noting new Quadro 4000 owners need to Reinstall the Nvidia Quadro driver update after updating to 10.6.6.
To save you a lot of clicks (the doc links to the nvidia product page) - here's the page with the current (as of this AM) Quadro OS X 10.6.5 Driver page which still shows the 11/16/2010 driver date/v256.01.00f03. But the file I downloaded this morning is named "Retail_256.01.00f03v5.dmg" (28.9MB) - dated Dec 17th. The file I downloaded back in mid-Nov does not have the "V5" in the filename and is larger (37.3MB). I don't own this card and not dug into the pkg to see what changed (i.e. did they remove the extra kexts for other models perhaps?) but just a FYI.
http://www.xlr8yourmac.com/archives/jan11/010611.html#quadro4000
http://support.apple.com/kb/HT4499
http://www.nvidia.com/object/quadro-macosx-256.01.00f03-driver.html
Reinstall the 10.6.6 combo update manually is sometimes a good idea (some of us use only combo updates when it comes time to update OS X).
Here: http://support.apple.com/kb/DL1349

Audio / Sound Card not working after Soundblaster.USB.Audio.Support.pkg

Ok, first - confess - it was stupid. I installed the Soundblaster.USB.Audio.Support.pkg package, which i downloaded from the internet, to make the harman Kardon Soundsticks (USB-Version) working, as nothing happened when plugging them in.
First, it ruined the mouse working after reboot and also disabled the internal sound card, not even as device available anymore. I fixed the mouse problem by installing IOUSBFamily-281.4.0-log(PPC).dmg
How can I make the sound card be available and working again ? I also updated to 10.4.11. Did not help ! Can you ? Thanks !

Welcome to the Apple discussions.
First, look in system preferences, accounts, and for your login account look at login items to see if there is a Soundblaster USB module that is loaded when you reboot your system. Delete it if there is one.
If you updated to 10.4.11 by software update, download the combo update from http://www.apple.com/downloads/macosx/apple/macosx_updates/macosx10411comboupdat eppc.html . The combo update is a complete update for all updates to 10.4, and installing the combo sometimes fixes odd things.

HT4623 Data card not working after 6.1 update

After updating my ipad 3 the data card has stopped working. This happened before. With the last update, But this time I can't seem to fix it

I am having the same problem it is saying that i have headphone plugged in when i dont. i Just did the update on monday and now i am having this problem!

W520 - nVidia optimus does not work after memory upgrade

Hello,
I have W520 16Gb (4*4Gb) running Windows Server 2008R2. Everything works fine - display sets to Optimus.
I've tried to upgrade the memory to 24Gb (2*4Gb + 2*8Gb). Laptop recognizes memory just fine. Memtest+ does not report any errors. Although Windows does not boot up with Optimus set in BIOS. It stucks on black screen during OS boot.
It starts in safe mode. Nothing particularly interesting in event log. It also starts just fine if I choose to use Discrete Graphics in the BIOS but in that mode it does not support 3 monitors..
Latest drivers, latest BIOS..
Does anybody experience this issue?

Hi dwkor
How about reseating the memory in another order?
http://forums.lenovo.com/t5/W-Series-ThinkPad-Laptops/Optimizing-memory-in-W510-which-slots-to-use/t...
Following the picture in the link above
Insert your 8GB stick at Slot 0 (Keyboard Side, top) and Slot 1 (Bottom Side, nearer to the screw hole)
Insert your 4GB stick at Slot 2 (Keyboard Side, bottom) and Slot 3 (Bottom Side)
Keyboard Side (Slot2: 4GB + Slot0: 8GB)
Bottom Side (Slot1: 8GB + Slot3: 4GB)
According to Lenovo, For W510 / W520 systems with 4 memory DIMMs installed, place the largest memory DIMM into DIMM slot 0, place the second largest DIMM in DIMM slot 1, place the third largest DIMM in DIMM Slot 2, and place the fourth DIMM in DIMM Slot 3.
True, tested with Windows Experience Index on my W520 with 8GB DDR3 1333MHz RAM.
Score: 7.5 (Slot 0 + 2, 1 + 3, etc. with random BSODs)
Score: 7.6 (Slot 0 + 1)
Hope this helps!
Happy 2012!
Peter
W520 (4284-A99)
Does someone’s post help you? Give them kudos as a reward, as they will do better to improve | Mark it as solved if the solution works for you, so it could be reference for others in the future
=====================================
Sound Enthusiast and Enhancement (Post comments, share mixes, etc.)
http://forums.lenovo.com/t5/General-Discussion/Dolby-Home-Theater-v4-for-most-Lenovo-Laptops/td-p/62...

Applications on Memory Card not working after Firm...

I have an N73 that I back up regularly, including the memory card.
My PC suite informed me that there was a newer version of firmware for my phone so I decided to upgrade.
I did a complete backup of my phone and card and then did the upgrade.
I then did a restore from the backup to get all my contact etc back again.
All applications that were loaded on my phone are working but none of the applications on the card will start.
Anyone got an ideas on how I can get them working again? Preferably without having to re-load as that will mean I will have to buy them again.

juz go to application manager. in it, u can see the applications u have installed previously are stating uninstalled. juz install them once again, n they will retrieve.

Airport Card Not Working After Replacing LCD Screen

My iBook G4 had a broken screen so I bought the LCD display and replaced the screen. But now my Airport gets no signal. I know I didn't break anything on the card nor the antenna. Any ideas??? It says the airport is on, but i just have no signal.
iBook G4, PowerMac G4 Mac OS X (10.4.7)

Thanks man. I will take a look at it later on tonight and see what happens. From my understanding some of these LCD's have the airport built-in or is it the antenna? I think mine is one of those, But it looked like the antenna just runs on the side of the casing for the LCD display which is still intact as I only removed the actual LCD screen. I'm gonna see if the connector is in fact not pushed in all the way although I never touched it.

Re: Graphics card not working after Windows 10 install

Hi, i still have my original SCM installed, like from the original 8.1 install.
Is there a new version released for Windows 10 maybe? I don't know what could be causing this.

Hi there,
I am using MSI motherboard 970A-G45 and windows 7 BIOS is at 1.11
However if i upgrade to Windows 10 does that mean i have to upgrade to (Windows 8) BIOS 2.7 or wait until they release the BIOS driver for Windows 10.
They managed to update mo...

Card slot does not work after update (14/10/2011)

Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
MacBook Pro 13 OS ver. 10.6.8

Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks

PCI wireless card does not work after restart - FM2-A55M-E33

Installed TP-LINK WN751ND wireless PCI card onto FM2-A55M-E33 motherboard. The card works fine after cold start, but does not work after restart. Windows recognises the card, but it gets code 10, cannot start.
BIOS is updated (v.11.1), as well as drivers and Windows 7 64.
I suspect that this might be the issue: Incorrect ASPM Transitions on the GPP Interface as found in ChipsetMotherboard_TechDocs/48671.pdf on AMD's official support site.
Does anyone know more about this issue?

Great! I've done that and now my card shows up. Thing is, when I try to get an IP address, it won't work. Here is the command output:
ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
And then it times out and no IP is assigned. The thing is, wpa_supplicant stays alive after this time out, and I am unable to kill it (killall -9 wpa_supplicant won't kill it). At this point if I try to reboot the machine, it will stop at 'Rebooting' and won't go anywhere. If I turn off the wireless card in its switch Linux crashes. If I try to get an ip again (by running dhcpcd) the command will hang and not return to the shell anymore.
I am unable to find any useful information in the logs.
Got any more suggestions?
Thanks! (And sorry to disturb so much)

Runtime error R6025 message after log on to Vista - Flash Card not working

Hi
I'm a newbie & would appreciate any advice.
I am getting a runtime error message R6025 when I log on to Windows Vista.
When I click out of the box I then get a message saying Toshiba Flash Card not working.
I cancel that and my laptop is ok except I don't know if the flashcard is working or not because I don't know what it does.
Sorry if I sound thick
Thanks
Neelie

Hi
I found this MS knowledge base article:
+Description of the R6025 run-time error in Visual C++\+
http://support.microsoft.com/kb/125749
But I doubt this description would be useful for you or anyone here. It describes this error in Visual C++ and this is programming language.
However, I think you should simply reinstall the Value Added Package which you could download firstly from the Toshiba European page.
At first you have to remove the old Value Added Package from the system, then reboot the notebook and follow with new VAP installation.
Bye

Fine tuning nvidia quadro k4000 to work with premiere pro cc

Would anyone know the correct settings for nvidia quadro k4000 to work with premiere pro cc please?
Currently it's only using 33% of it's full power when rendering, while the CPU is running @ 95%
Mercury playback engine GPU is selected.
Thank you in advance

why would the encoder have the option to choose between mercury playback engine using GPU, or sofware encoding only!
From the article linked to earlier:
The video card and hardware MPE is not the holy grail. It helps in some circumstances to improve performance and rather significantly, but in other instances it does not help at all, as is indicated in the link above. People often think that installing a super fast video card will reduce export times by a significant amount of time. That is not true. It only helps in a limited number of situations. Keep in mind that:
Encoding to an export format is done by the CPU, not the GPU. No performance gain from a video card.
Frame rate changes, frame blending is done by a suitable video card, for instance exporting to 24P from 29.97i or 60P. Here there is a clear performance gain.
Scaling is also helped by hardware MPE, for instance going from 4K to HD or from HD to SD. Again a clear performance gain.
Rendering for preview is helped by the video card only for accelerated effects.

HT1688 My Hot Spot does not work after update to 6.0.1. Service is with ATT. Apple says problem is with ATT, ATT says problem is with Apple. Anyone else having this problem?

My Hot Spot does not work after update to 6.0.1. Any suggestions?

Ok, I had the same issue, my phone is unlocked(iphone 5 with 6.1.3). So I went to the apple store and had it replaced. it worked good for a day and started doing the same thing. When the apple tech replaced my phone, he transfered my screen protector to the new one.
so I thought it was my sim card, I put in my sisters sim card from a different carrier and it did the same, so then I was like let me take off the screen protector, and that was it.
so guys, if you have a screen protector on your phone and it's doing "low signal", "No Service", "Searching", "Full bars cycle" then take off the screen protector. so far my phone is working normal.

Nvidia Quadro card not working after 10.6.6

Similar Messages

Maybe you are looking for