NVidia RAID using existing drives?
Hi folks --
Just installed WinXP x64 (build 1218). I've been using an Adaptec 1200A RAID controller with 2 200GB Maxtor PATA133 drives in a RAID1 config.
Unfortunately, there seems to be no 64-bit driver available for that controller card (I've checked Adaptec, planetAMD64, various other places). So the question is: can I set up these drives as RAID1 on the nVidia built-in controller without losing data? These are not bootable drives -- storage only.
The MSI mobo booklet explains a "Rebuild Array" option, where if one of the drives in the array fails, the data on the remaining drive can be mirrored to a new one. Will that work if the source drive was not part of an nVidia array to start with?
I can't afford to lose that data, and I have no place to back it up (without buying another drive). So don't even wanna risk it without some guidance!
One possible complication: the system also includes a Promise Tx ATA133 controller, which is controlling the boot drive (Win64 included a 64-bit driver for this). There is no conflict under Win2k, however.
Anyone have some savvy on this? Or know where to get a 64-bit controller for the Adaptec card?
Thanks!
SYSTEM:
MSI K8N Neo2 Platinum
AMD64 3500+
1 GB Crucial PC3200 DDR
Dual boot: Win2k, WinXPx64
Promise Tx ATA133 IDE controller
ATI 9800 XT
Soundblaster Audigy2
PS: All the rest of this system is working fine, so if anyone is having probs with a similar setup, I'd be happy to help.
Earlier posts on this site, may be in the sata/raid sticky , that the only time a raid can be remade is when using the same controller. Doubt very much that Adaptec & Nvidia raid components are interchangable
i know to my cost on previous rigs that even changing a raid driver has caused the loss of data.
creating a new raid destroys any data on the target drives.
rebuild only applies to drives in an existing array created i would guess with the same controller.
Chances also are that any 64 adaptec drivers will only be beta and your raid may be at risk changing to these from existing drivers.
my advise has to be if u cant back it up dont do it
Similar Messages
-
Nvidia RAID Driver Disk
The problem is with trying to Install Windows XP [Upgrade]. (Clean Install)
K7N2 Delta2-LSR
I tried using the nForce3 SATA RAID Driver For Win2k/XP after pressing F6,
during XP Install.
They don't work, and after trying a couple of times - got an error reading.
This Motherboard has an nForce2 Chipset, so I read the Manual.
It showed how to make an Floppy SATA RAID Driver Disk.
I tried to copy the SATA RAID Drivers from the MSI Driver's CD - but
got Disk Full.
Then I downloaded an Program to Format Floppy at 1.72MB, and copied
all the necessary files to Floppy.
Tried using it after pressing F6, but got Error - Unrecoginized Format.
(The Floppy did read OK, MS-WIN ME)
BTW I thought this Motherboard used nForce2 SATA RAID, why they include
nForce3 SATA RAID Driver Floppy - I wonder.
Any way to get SATA RAID Driver's that will fit on FDD 1.44MB ?
[size=18]TheCyberDude[/size][size=18]UPDATE[/size][/b]
I looked at the nForce3 SATA RAID Driver, and the Folder raidtool was not on it.
They Manual said to copy all files (Including Folders) to Floppy.
(This wasn't posible, because of size limitation - 1.44 MB)
So I made an SATA RAID Driver from the MSI CD, except I didn't copy the
Folder raidtool.
I tried to install Windows XP Again, it Took the SATA RAID Drivers OK -
but after it said Setup loading files and the STALLS at Setup is Starting
Windows.
Tried it again, except this time I got this error:
(File txtsetup.oem caused an unexpected error (1024) at line 1747 in
d:\xpsprtm\base\boot\setup\oemdisk.c.)
If I don't Press F6, it shows the partitions:
39080 MB Disk 0 at Id 0 on bus 0 on atapi [MBR]
C: Partition1 [FAT32] 78160 MB (77280 MB free)
39080 MB Disk 0 at Id 0 on bus 0 on atapi [MBR]
Unpartitioned space 39080MB
I was able to Format with NTFS (Successfully), but it wasn't recongized.
(Figured that it wouldn't - Because I was able to get SATA RAID Driver's loaded Successfully)
Just wanted to see what it would do.
TheCyberDude -
Screen flickering and system freezes when using Nouveau driver.
I'm testing the Nouveau driver on my computer, I really want to keep this driver installed because it makes XFCE to use less resources than the Nvidia proprietary driver. But when I start some apps like firefox or make changes to the desktop, the system stop responding and then the screen breaks.
I can't use the computer in that state so I force a shutdown.
I don't know how to see what is going wrong, because the proprietary driver don't give me these problems, I don't get any errors at dmesg log and Xorg log don't have any helpful information.
dmesg output:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8.3-2-ARCH (tobias@testing) (gcc version 4.7.2 (GCC) ) #1 SMP PREEMPT Sun Mar 17 13:38:16 CET 2013
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f3ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f400-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000057feffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000057ff0000-0x0000000057ff2fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x0000000057ff3000-0x0000000057ffffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x0000000058000000-0x000000005fffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] SMBIOS 2.3 present.
[ 0.000000] DMI: Acer Aspire T180/EM61SM/EM61PM , BIOS R01-B4 06/15/2007
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x57ff0 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FFC0000000 write-back
[ 0.000000] 1 base 0040000000 mask FFE0000000 write-back
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [mem 0x000f3c90-0x000f3c9f] mapped at [c00f3c90]
[ 0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x377fdfff]
[ 0.000000] [mem 0x00000000-0x003fffff] page 4k
[ 0.000000] [mem 0x00400000-0x373fffff] page 2M
[ 0.000000] [mem 0x37400000-0x377fdfff] page 4k
[ 0.000000] kernel direct mapping tables up to 0x377fdfff @ [mem 0x01bfa000-0x01bfffff]
[ 0.000000] RAMDISK: [mem 0x37a46000-0x37d1afff]
[ 0.000000] Allocated new RAMDISK: [mem 0x37529000-0x377fd69f]
[ 0.000000] Move RAMDISK from [mem 0x37a46000-0x37d1a69f] to [mem 0x37529000-0x377fd69f]
[ 0.000000] ACPI: RSDP 000f8370 00014 (v00 ACRSYS)
[ 0.000000] ACPI: RSDT 57ff3040 0003C (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000000)
[ 0.000000] ACPI: FACP 57ff30c0 00074 (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000000)
[ 0.000000] ACPI: DSDT 57ff3180 0631A (v01 ACRSYS AWRDACPI 00001000 MSFT 0100000E)
[ 0.000000] ACPI: FACS 57ff0000 00040
[ 0.000000] ACPI: SSDT 57ff95c0 001C4 (v01 PTLTD POWERNOW 00000001 LTP 00000001)
[ 0.000000] ACPI: HPET 57ff9800 00038 (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000098)
[ 0.000000] ACPI: SLIC 57ff9880 00176 (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000001)
[ 0.000000] ACPI: MCFG 57ff9a40 0003C (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000000)
[ 0.000000] ACPI: APIC 57ff9500 0007C (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 519MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x377fdfff]
[ 0.000000] HighMem [mem 0x377fe000-0x57feffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x57feffff]
[ 0.000000] On node 0 totalpages: 360319
[ 0.000000] free_area_init_node: node 0, pgdat c15ab3c0, node_mem_map f6a28200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1040 pages used for memmap
[ 0.000000] HighMem zone: 132066 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] Detected use of extended apic ids on hypertransport bus
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfeff0000
[ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] e820: [mem 0x60000000-0xefffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @f6a05000 s32640 r0 d20608 u53248
[ 0.000000] pcpu-alloc: s32640 r0 d20608 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 357503
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=bb82c8c9-614f-4ce3-85f2-3597507c391d ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 2883328 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000377fe:00057ff0)
[ 0.000000] Memory: 1415956k/1441728k available (4184k kernel code, 25320k reserved, 1679k data, 560k init, 532424k highmem)
[ 0.000000] virtual kernel memory layout:
fixmap : 0xfff15000 - 0xfffff000 ( 936 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc15ba000 - 0xc1646000 ( 560 kB)
.data : 0xc141613e - 0xc15b9d80 (1679 kB)
.text : 0xc1000000 - 0xc141613e (4184 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=f6008000 soft=f600a000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 1908.551 MHz processor
[ 0.000000] tsc: Marking TSC unstable due to TSCs unsynchronized
[ 0.003338] Calibrating delay loop (skipped), value calculated using timer frequency.. 3818.14 BogoMIPS (lpj=6361836)
[ 0.003343] pid_max: default: 32768 minimum: 301
[ 0.003404] Security Framework initialized
[ 0.003415] AppArmor: AppArmor disabled by boot time parameter
[ 0.003432] Mount-cache hash table entries: 512
[ 0.006819] Initializing cgroup subsys cpuacct
[ 0.006822] Initializing cgroup subsys memory
[ 0.006834] Initializing cgroup subsys devices
[ 0.006837] Initializing cgroup subsys freezer
[ 0.006840] Initializing cgroup subsys net_cls
[ 0.006842] Initializing cgroup subsys blkio
[ 0.006879] CPU: Physical Processor ID: 0
[ 0.006882] CPU: Processor Core ID: 0
[ 0.006885] mce: CPU supports 5 MCE banks
[ 0.006896] LVT offset 0 assigned for vector 0xf9
[ 0.006902] process: using AMD E400 aware idle routine
[ 0.006911] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4
tlb_flushall_shift: 4
[ 0.007021] Freeing SMP alternatives: 16k freed
[ 0.007977] ACPI: Core revision 20121018
[ 0.015366] ftrace: allocating 18273 entries in 36 pages
[ 0.023490] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.024036] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.059250] smpboot: CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ (fam: 0f, model: 6b, stepping: 01)
[ 0.059999] Performance Events: AMD PMU driver.
[ 0.059999] ... version: 0
[ 0.059999] ... bit width: 48
[ 0.059999] ... generic registers: 4
[ 0.059999] ... value mask: 0000ffffffffffff
[ 0.059999] ... max period: 00007fffffffffff
[ 0.059999] ... fixed-purpose events: 0
[ 0.059999] ... event mask: 000000000000000f
[ 0.078439] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.083409] CPU 1 irqstacks, hard=f60ba000 soft=f60bc000
[ 0.083412] smpboot: Booting Node 0, Processors #1 OK
[ 0.006666] Initializing CPU#1
[ 0.176732] Brought up 2 CPUs
[ 0.176736] smpboot: Total of 2 processors activated (7637.24 BogoMIPS)
[ 0.177423] devtmpfs: initialized
[ 0.177423] PM: Registering ACPI NVS region [mem 0x57ff0000-0x57ff2fff] (12288 bytes)
[ 0.178162] RTC time: 21:06:38, date: 03/21/13
[ 0.178225] NET: Registered protocol family 16
[ 0.178397] node 0 link 0: io port [8000, ffff]
[ 0.178401] TOM: 0000000060000000 aka 1536M
[ 0.178404] node 0 link 0: mmio [a0000, bffff]
[ 0.178408] node 0 link 0: mmio [60000000, efffffff]
[ 0.178411] node 0 link 0: mmio [f4000000, fe02ffff]
[ 0.178414] node 0 link 0: mmio [f0000000, f03fffff]
[ 0.178418] bus: [bus 00-04] on node 0 link 0
[ 0.178421] bus: 00 [io 0x0000-0xffff]
[ 0.178423] bus: 00 [mem 0x000a0000-0x000bffff]
[ 0.178425] bus: 00 [mem 0x60000000-0xf3ffffff]
[ 0.178428] bus: 00 [mem 0xf4000000-0xffffffff]
[ 0.178495] ACPI: bus type pci registered
[ 0.178575] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[ 0.178579] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
[ 0.178581] PCI: Using MMCONFIG for extended config space
[ 0.178583] PCI: Using configuration type 1 for base access
[ 0.178677] mtrr: your CPUs had inconsistent variable MTRR settings
[ 0.178679] mtrr: probably your BIOS does not setup all CPUs.
[ 0.178681] mtrr: corrected configuration.
[ 0.180670] bio: create slab <bio-0> at 0
[ 0.180670] ACPI: Added _OSI(Module Device)
[ 0.180670] ACPI: Added _OSI(Processor Device)
[ 0.180670] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.180670] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.181260] ACPI: EC: Look up EC in DSDT
[ 0.186070] ACPI: Interpreter enabled
[ 0.186077] ACPI: (supports S0 S3 S4 S5)
[ 0.186098] ACPI: Using IOAPIC for interrupt routing
[ 0.193127] ACPI: No dock devices found.
[ 0.193134] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.193752] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-04])
[ 0.193756] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.193890] pci_root PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.193894] pci_root PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.195031] pci_root PNP0A08:00: host bridge window [io 0x0000-0x03af] (ignored)
[ 0.195034] pci_root PNP0A08:00: host bridge window [io 0x03e0-0x0cf7] (ignored)
[ 0.195037] pci_root PNP0A08:00: host bridge window [io 0x8000-0xffff] (ignored)
[ 0.195040] pci_root PNP0A08:00: host bridge window [io 0x03b0-0x03df] (ignored)
[ 0.195044] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.195047] pci_root PNP0A08:00: host bridge window [mem 0x60000000-0xefffffff] (ignored)
[ 0.195050] pci_root PNP0A08:00: host bridge window [mem 0xf4000000-0xfe02ffff] (ignored)
[ 0.195053] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff] (ignored)
[ 0.195057] pci_root PNP0A08:00: host bridge window [io 0x4700-0x470b] (ignored)
[ 0.195060] pci_root PNP0A08:00: host bridge window [io 0x1c00-0x1c80] (ignored)
[ 0.195063] pci_root PNP0A08:00: host bridge window [mem 0xfec80000-0xfecbffff] (ignored)
[ 0.195066] PCI: root bus 00: hardware-probed resources
[ 0.195117] PCI host bridge to bus 0000:00
[ 0.195121] pci_bus 0000:00: root bus resource [bus 00-04]
[ 0.195124] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.195127] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.195130] pci_bus 0000:00: root bus resource [mem 0x60000000-0xf3ffffff]
[ 0.195134] pci_bus 0000:00: root bus resource [mem 0xf4000000-0xffffffff]
[ 0.195161] pci 0000:00:00.0: [10de:03ea] type 00 class 0x050000
[ 0.195341] pci 0000:00:01.0: [10de:03e0] type 00 class 0x060100
[ 0.195384] pci 0000:00:01.1: [10de:03eb] type 00 class 0x0c0500
[ 0.195397] pci 0000:00:01.1: reg 10: [io 0xfc00-0xfc3f]
[ 0.195414] pci 0000:00:01.1: reg 20: [io 0x1c00-0x1c3f]
[ 0.195421] pci 0000:00:01.1: reg 24: [io 0xf400-0xf43f]
[ 0.195452] pci 0000:00:01.1: PME# supported from D3hot D3cold
[ 0.195469] pci 0000:00:01.2: [10de:03f5] type 00 class 0x050000
[ 0.195516] pci 0000:00:02.0: [10de:03f1] type 00 class 0x0c0310
[ 0.195527] pci 0000:00:02.0: reg 10: [mem 0xfe02f000-0xfe02ffff]
[ 0.195564] pci 0000:00:02.0: supports D1 D2
[ 0.195567] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.195583] pci 0000:00:02.1: [10de:03f2] type 00 class 0x0c0320
[ 0.195595] pci 0000:00:02.1: reg 10: [mem 0xfe02e000-0xfe02e0ff]
[ 0.195639] pci 0000:00:02.1: supports D1 D2
[ 0.195642] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.195665] pci 0000:00:04.0: [10de:03f3] type 01 class 0x060401
[ 0.195711] pci 0000:00:05.0: [10de:03f0] type 00 class 0x040300
[ 0.195723] pci 0000:00:05.0: reg 10: [mem 0xfe028000-0xfe02bfff]
[ 0.195768] pci 0000:00:05.0: PME# supported from D3hot D3cold
[ 0.195791] pci 0000:00:06.0: [10de:03ec] type 00 class 0x01018a
[ 0.195814] pci 0000:00:06.0: reg 20: [io 0xf000-0xf00f]
[ 0.195850] pci 0000:00:08.0: [10de:03f6] type 00 class 0x010185
[ 0.195860] pci 0000:00:08.0: reg 10: [io 0x09f0-0x09f7]
[ 0.195866] pci 0000:00:08.0: reg 14: [io 0x0bf0-0x0bf3]
[ 0.195872] pci 0000:00:08.0: reg 18: [io 0x0970-0x0977]
[ 0.195877] pci 0000:00:08.0: reg 1c: [io 0x0b70-0x0b73]
[ 0.195883] pci 0000:00:08.0: reg 20: [io 0xdc00-0xdc0f]
[ 0.195889] pci 0000:00:08.0: reg 24: [mem 0xfe02d000-0xfe02dfff]
[ 0.195922] pci 0000:00:08.1: [10de:03f6] type 00 class 0x010185
[ 0.195932] pci 0000:00:08.1: reg 10: [io 0x09e0-0x09e7]
[ 0.195938] pci 0000:00:08.1: reg 14: [io 0x0be0-0x0be3]
[ 0.195944] pci 0000:00:08.1: reg 18: [io 0x0960-0x0967]
[ 0.195949] pci 0000:00:08.1: reg 1c: [io 0x0b60-0x0b63]
[ 0.195955] pci 0000:00:08.1: reg 20: [io 0xc800-0xc80f]
[ 0.195961] pci 0000:00:08.1: reg 24: [mem 0xfe02c000-0xfe02cfff]
[ 0.196000] pci 0000:00:09.0: [10de:03e8] type 01 class 0x060400
[ 0.196032] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.196051] pci 0000:00:0b.0: [10de:03e9] type 01 class 0x060400
[ 0.196081] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.196098] pci 0000:00:0c.0: [10de:03e9] type 01 class 0x060400
[ 0.196128] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.196146] pci 0000:00:0d.0: [10de:03d0] type 00 class 0x030000
[ 0.196154] pci 0000:00:0d.0: reg 10: [mem 0xfb000000-0xfbffffff]
[ 0.196162] pci 0000:00:0d.0: reg 14: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.196169] pci 0000:00:0d.0: reg 1c: [mem 0xfc000000-0xfcffffff 64bit]
[ 0.196177] pci 0000:00:0d.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.196209] pci 0000:00:18.0: [1022:1100] type 00 class 0x060000
[ 0.196233] pci 0000:00:18.1: [1022:1101] type 00 class 0x060000
[ 0.196253] pci 0000:00:18.2: [1022:1102] type 00 class 0x060000
[ 0.196273] pci 0000:00:18.3: [1022:1103] type 00 class 0x060000
[ 0.196335] pci 0000:01:09.0: [104c:8024] type 00 class 0x0c0010
[ 0.196350] pci 0000:01:09.0: reg 10: [mem 0xfdfff000-0xfdfff7ff]
[ 0.196359] pci 0000:01:09.0: reg 14: [mem 0xfdff8000-0xfdffbfff]
[ 0.196412] pci 0000:01:09.0: supports D1 D2
[ 0.196415] pci 0000:01:09.0: PME# supported from D0 D1 D2 D3hot
[ 0.196444] pci 0000:00:04.0: PCI bridge to [bus 01] (subtractive decode)
[ 0.196448] pci 0000:00:04.0: bridge window [io 0xb000-0xbfff]
[ 0.196452] pci 0000:00:04.0: bridge window [mem 0xfdf00000-0xfdffffff]
[ 0.196456] pci 0000:00:04.0: bridge window [mem 0xfd800000-0xfd8fffff pref]
[ 0.196459] pci 0000:00:04.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.196462] pci 0000:00:04.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.196465] pci 0000:00:04.0: bridge window [mem 0x60000000-0xf3ffffff] (subtractive decode)
[ 0.196469] pci 0000:00:04.0: bridge window [mem 0xf4000000-0xffffffff] (subtractive decode)
[ 0.196493] pci 0000:00:09.0: PCI bridge to [bus 02]
[ 0.196498] pci 0000:00:09.0: bridge window [io 0xa000-0xafff]
[ 0.196501] pci 0000:00:09.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 0.196506] pci 0000:00:09.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
[ 0.196548] pci 0000:03:00.0: [11ab:4364] type 00 class 0x020000
[ 0.196565] pci 0000:03:00.0: reg 10: [mem 0xfdcfc000-0xfdcfffff 64bit]
[ 0.196575] pci 0000:03:00.0: reg 18: [io 0x9c00-0x9cff]
[ 0.196604] pci 0000:03:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.196648] pci 0000:03:00.0: supports D1 D2
[ 0.196651] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.203353] pci 0000:00:0b.0: PCI bridge to [bus 03]
[ 0.203357] pci 0000:00:0b.0: bridge window [io 0x9000-0x9fff]
[ 0.203361] pci 0000:00:0b.0: bridge window [mem 0xfdc00000-0xfdcfffff]
[ 0.203365] pci 0000:00:0b.0: bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
[ 0.203390] pci 0000:00:0c.0: PCI bridge to [bus 04]
[ 0.203394] pci 0000:00:0c.0: bridge window [io 0x8000-0x8fff]
[ 0.203398] pci 0000:00:0c.0: bridge window [mem 0xfda00000-0xfdafffff]
[ 0.203402] pci 0000:00:0c.0: bridge window [mem 0xfd900000-0xfd9fffff 64bit pref]
[ 0.203413] pci_bus 0000:00: on NUMA node 0
[ 0.203424] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.203569] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.242482] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.242536] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.242587] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.242639] ACPI: PCI Interrupt Link [LNK4] (IRQs *5 7 9 10 11 14 15)
[ 0.242689] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.242741] ACPI: PCI Interrupt Link [LNK6] (IRQs *5 7 9 10 11 14 15)
[ 0.242791] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.242842] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.242894] ACPI: PCI Interrupt Link [LIGP] (IRQs 5 7 9 10 *11 14 15)
[ 0.242944] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.242996] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15)
[ 0.243045] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.243098] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
[ 0.243148] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.243204] ACPI: PCI Interrupt Link [LSMB] (IRQs *5 7 9 10 11 14 15)
[ 0.243265] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15)
[ 0.243315] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.243375] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15)
[ 0.243432] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15)
[ 0.243524] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 0.243606] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 0.243688] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 0.243770] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
[ 0.243851] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
[ 0.243933] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0
[ 0.244014] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
[ 0.244095] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
[ 0.244176] ACPI: PCI Interrupt Link [AIGP] (IRQs 20 21 22 23) *0
[ 0.244258] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
[ 0.244340] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
[ 0.244422] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[ 0.244504] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
[ 0.244586] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[ 0.244669] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
[ 0.244751] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[ 0.244833] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 0.244921] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[ 0.245004] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
[ 0.245086] vgaarb: device added: PCI:0000:00:0d.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.245086] vgaarb: loaded
[ 0.245086] vgaarb: bridge control possible 0000:00:0d.0
[ 0.245086] PCI: Using ACPI for IRQ routing
[ 0.246696] PCI: pci_cache_line_size set to 64 bytes
[ 0.246745] e820: reserve RAM buffer [mem 0x0009f400-0x0009ffff]
[ 0.246748] e820: reserve RAM buffer [mem 0x57ff0000-0x57ffffff]
[ 0.246902] NetLabel: Initializing
[ 0.246904] NetLabel: domain hash size = 128
[ 0.246906] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.246923] NetLabel: unlabeled traffic allowed by default
[ 0.246950] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.246956] hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
[ 0.246961] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[ 0.256702] Switching to clocksource hpet
[ 0.264319] pnp: PnP ACPI init
[ 0.264346] ACPI: bus type pnp registered
[ 0.264605] system 00:00: [io 0x1000-0x107f] has been reserved
[ 0.264609] system 00:00: [io 0x1080-0x10ff] has been reserved
[ 0.264613] system 00:00: [io 0x1400-0x147f] has been reserved
[ 0.264616] system 00:00: [io 0x1480-0x14ff] has been reserved
[ 0.264620] system 00:00: [io 0x1800-0x187f] has been reserved
[ 0.264623] system 00:00: [io 0x1880-0x18ff] has been reserved
[ 0.264628] system 00:00: [mem 0xfefe0000-0xfefe01ff] has been reserved
[ 0.264631] system 00:00: [mem 0xfefe1000-0xfefe10ff] has been reserved
[ 0.264635] system 00:00: [mem 0x58000000-0x5fffffff] has been reserved
[ 0.264641] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.265431] system 00:01: [io 0x04d0-0x04d1] has been reserved
[ 0.265434] system 00:01: [io 0x0800-0x087f] has been reserved
[ 0.265438] system 00:01: [io 0x0290-0x0297] has been reserved
[ 0.265442] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.265458] pnp 00:02: [dma 4]
[ 0.265495] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.265606] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.265670] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.265714] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.265772] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.266190] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.266522] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.266948] pnp 00:09: Plug and Play ACPI device, IDs PNP0400 (active)
[ 0.267129] pnp 00:0a: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 0.267201] pnp 00:0b: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.267285] system 00:0c: [mem 0xf0000000-0xf3ffffff] has been reserved
[ 0.267290] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.267506] system 00:0d: [mem 0x000d0000-0x000d3fff] has been reserved
[ 0.267510] system 00:0d: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.267514] system 00:0d: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.267517] system 00:0d: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.267521] system 00:0d: [mem 0xfeff0000-0xfeff00ff] has been reserved
[ 0.267525] system 00:0d: [mem 0x57ff0000-0x57ffffff] could not be reserved
[ 0.267528] system 00:0d: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.267532] system 00:0d: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.267535] system 00:0d: [mem 0x00100000-0x57feffff] could not be reserved
[ 0.267539] system 00:0d: [mem 0x58000000-0x5fffffff] has been reserved
[ 0.267543] system 00:0d: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.267546] system 00:0d: [mem 0xfee00000-0xfeefffff] has been reserved
[ 0.267550] system 00:0d: [mem 0xfefff000-0xfeffffff] has been reserved
[ 0.267554] system 00:0d: [mem 0xfff80000-0xfff80fff] has been reserved
[ 0.267557] system 00:0d: [mem 0xfff90000-0xfffbffff] has been reserved
[ 0.267561] system 00:0d: [mem 0xfffed000-0xfffeffff] has been reserved
[ 0.267565] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.267589] pnp: PnP ACPI: found 14 devices
[ 0.267590] ACPI: ACPI bus type pnp unregistered
[ 0.305593] pci 0000:00:0d.0: BAR 6: assigned [mem 0x60000000-0x6001ffff pref]
[ 0.305599] pci 0000:00:04.0: PCI bridge to [bus 01]
[ 0.305603] pci 0000:00:04.0: bridge window [io 0xb000-0xbfff]
[ 0.305608] pci 0000:00:04.0: bridge window [mem 0xfdf00000-0xfdffffff]
[ 0.305612] pci 0000:00:04.0: bridge window [mem 0xfd800000-0xfd8fffff pref]
[ 0.305617] pci 0000:00:09.0: PCI bridge to [bus 02]
[ 0.305621] pci 0000:00:09.0: bridge window [io 0xa000-0xafff]
[ 0.305625] pci 0000:00:09.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 0.305629] pci 0000:00:09.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
[ 0.305635] pci 0000:03:00.0: BAR 6: assigned [mem 0xfdb00000-0xfdb1ffff pref]
[ 0.305638] pci 0000:00:0b.0: PCI bridge to [bus 03]
[ 0.305641] pci 0000:00:0b.0: bridge window [io 0x9000-0x9fff]
[ 0.305645] pci 0000:00:0b.0: bridge window [mem 0xfdc00000-0xfdcfffff]
[ 0.305649] pci 0000:00:0b.0: bridge window [mem 0xfdb00000-0xfdbfffff 64bit pref]
[ 0.305654] pci 0000:00:0c.0: PCI bridge to [bus 04]
[ 0.305657] pci 0000:00:0c.0: bridge window [io 0x8000-0x8fff]
[ 0.305661] pci 0000:00:0c.0: bridge window [mem 0xfda00000-0xfdafffff]
[ 0.305665] pci 0000:00:0c.0: bridge window [mem 0xfd900000-0xfd9fffff 64bit pref]
[ 0.305677] pci 0000:00:04.0: setting latency timer to 64
[ 0.305686] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.305689] pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
[ 0.305692] pci_bus 0000:00: resource 6 [mem 0x60000000-0xf3ffffff]
[ 0.305696] pci_bus 0000:00: resource 7 [mem 0xf4000000-0xffffffff]
[ 0.305699] pci_bus 0000:01: resource 0 [io 0xb000-0xbfff]
[ 0.305702] pci_bus 0000:01: resource 1 [mem 0xfdf00000-0xfdffffff]
[ 0.305706] pci_bus 0000:01: resource 2 [mem 0xfd800000-0xfd8fffff pref]
[ 0.305709] pci_bus 0000:01: resource 4 [io 0x0000-0xffff]
[ 0.305712] pci_bus 0000:01: resource 5 [mem 0x000a0000-0x000bffff]
[ 0.305715] pci_bus 0000:01: resource 6 [mem 0x60000000-0xf3ffffff]
[ 0.305718] pci_bus 0000:01: resource 7 [mem 0xf4000000-0xffffffff]
[ 0.305722] pci_bus 0000:02: resource 0 [io 0xa000-0xafff]
[ 0.305725] pci_bus 0000:02: resource 1 [mem 0xfde00000-0xfdefffff]
[ 0.305729] pci_bus 0000:02: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref]
[ 0.305732] pci_bus 0000:03: resource 0 [io 0x9000-0x9fff]
[ 0.305735] pci_bus 0000:03: resource 1 [mem 0xfdc00000-0xfdcfffff]
[ 0.305738] pci_bus 0000:03: resource 2 [mem 0xfdb00000-0xfdbfffff 64bit pref]
[ 0.305742] pci_bus 0000:04: resource 0 [io 0x8000-0x8fff]
[ 0.305745] pci_bus 0000:04: resource 1 [mem 0xfda00000-0xfdafffff]
[ 0.305748] pci_bus 0000:04: resource 2 [mem 0xfd900000-0xfd9fffff 64bit pref]
[ 0.305804] NET: Registered protocol family 2
[ 0.305997] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.306061] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.306122] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.306184] TCP: reno registered
[ 0.306188] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.306204] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.306279] NET: Registered protocol family 1
[ 0.306537] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
[ 0.370181] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[ 0.370249] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.370299] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.370357] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.370411] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.370469] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.370531] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.370598] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.370606] pci 0000:00:0d.0: Boot video device
[ 0.370621] PCI: CLS 64 bytes, default 64
[ 0.370687] Unpacking initramfs...
[ 0.455995] Freeing initrd memory: 2900k freed
[ 0.459106] apm: BIOS not found.
[ 0.459448] audit: initializing netlink socket (disabled)
[ 0.459468] type=2000 audit(1363899998.456:1): initialized
[ 0.474029] bounce pool size: 64 pages
[ 0.474052] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.476263] VFS: Disk quotas dquot_6.5.2
[ 0.476327] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.476593] msgmni has been set to 1731
[ 0.476998] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.477042] io scheduler noop registered
[ 0.477044] io scheduler deadline registered
[ 0.477053] io scheduler cfq registered (default)
[ 0.477195] pcieport 0000:00:09.0: irq 40 for MSI/MSI-X
[ 0.477269] pcieport 0000:00:0b.0: irq 41 for MSI/MSI-X
[ 0.477329] pcieport 0000:00:0c.0: irq 42 for MSI/MSI-X
[ 0.477469] vesafb: mode is 640x480x32, linelength=2560, pages=0
[ 0.477471] vesafb: scrolling: redraw
[ 0.477474] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.477558] vesafb: framebuffer at 0xe0000000, mapped to 0xf8080000, using 1216k, total 1216k
[ 0.484141] Console: switching to colour frame buffer device 80x30
[ 0.490611] fb0: VESA VGA frame buffer device
[ 0.490704] GHES: HEST is not enabled!
[ 0.490719] isapnp: Scanning for PnP cards...
[ 0.802592] isapnp: No Plug & Play device found
[ 0.802671] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.823231] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.843779] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.844469] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.844915] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.844951] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.845087] mousedev: PS/2 mouse device common for all mice
[ 0.845182] rtc_cmos 00:04: RTC can wake from S4
[ 0.845358] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.845400] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[ 0.845435] cpuidle: using governor ladder
[ 0.845437] cpuidle: using governor menu
[ 0.845439] EFI Variables Facility v0.08 2004-May-17
[ 0.845489] drop_monitor: Initializing network drop monitor service
[ 0.845593] TCP: cubic registered
[ 0.845736] NET: Registered protocol family 10
[ 0.845940] NET: Registered protocol family 17
[ 0.845958] Key type dns_resolver registered
[ 0.846129] Using IPI No-Shortcut mode
[ 0.846264] PM: Hibernation image not present or could not be loaded.
[ 0.846279] registered taskstats version 1
[ 0.846851] Magic number: 5:851:146
[ 0.846912] acpi device:17: hash matches
[ 0.846972] rtc_cmos 00:04: setting system clock to 2013-03-21 21:06:39 UTC (1363899999)
[ 0.847246] Freeing unused kernel memory: 560k freed
[ 0.847645] Write protecting the kernel text: 4188k
[ 0.847679] Write protecting the kernel read-only data: 1284k
[ 0.858078] systemd-udevd[45]: starting version 198
[ 0.864682] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.904637] ACPI: bus type usb registered
[ 0.904681] usbcore: registered new interface driver usbfs
[ 0.904697] usbcore: registered new interface driver hub
[ 0.904815] usbcore: registered new device driver usb
[ 0.906826] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.908458] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.908536] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 0.908541] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 0.908550] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 0.908594] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe02f000
[ 0.910252] ehci-pci: EHCI PCI platform driver
[ 0.910290] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 0.910329] firewire_ohci 0000:01:09.0: setting latency timer to 64
[ 0.912040] SCSI subsystem initialized
[ 0.915768] ACPI: bus type scsi registered
[ 0.918637] libata version 3.00 loaded.
[ 0.962268] hub 1-0:1.0: USB hub found
[ 0.962279] hub 1-0:1.0: 10 ports detected
[ 0.962535] ehci-pci 0000:00:02.1: setting latency timer to 64
[ 0.962539] ehci-pci 0000:00:02.1: EHCI Host Controller
[ 0.962547] ehci-pci 0000:00:02.1: new USB bus registered, assigned bus number 2
[ 0.962559] ehci-pci 0000:00:02.1: debug port 1
[ 0.962589] ehci-pci 0000:00:02.1: cache line size of 64 is not supported
[ 0.962617] ehci-pci 0000:00:02.1: irq 22, io mem 0xfe02e000
[ 0.970035] ehci-pci 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 0.970261] hub 2-0:1.0: USB hub found
[ 0.970268] hub 2-0:1.0: 10 ports detected
[ 0.970681] pata_amd 0000:00:06.0: version 0.4.1
[ 0.970736] pata_amd 0000:00:06.0: setting latency timer to 64
[ 0.971618] scsi0 : pata_amd
[ 0.972200] scsi1 : pata_amd
[ 0.972449] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 0.972452] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 0.972517] sata_nv 0000:00:08.0: version 3.5
[ 0.972721] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
[ 0.972802] sata_nv 0000:00:08.0: setting latency timer to 64
[ 0.973161] scsi2 : sata_nv
[ 0.973470] scsi3 : sata_nv
[ 0.973598] ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xdc00 irq 21
[ 0.973602] ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xdc08 irq 21
[ 0.973822] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
[ 0.973886] sata_nv 0000:00:08.1: setting latency timer to 64
[ 0.974209] scsi4 : sata_nv
[ 0.974369] scsi5 : sata_nv
[ 0.974488] ata5: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc800 irq 20
[ 0.974491] ata6: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc808 irq 20
[ 1.130346] ata1.00: ATAPI: HL-DT-ST DVDRAM_GSA-H40N, RA00, max UDMA/66
[ 1.130357] ata1: nv_mode_filter: 0x1f39f&0x1f39f->0x1f39f, BIOS=0x1f000 (0xc5000000) ACPI=0x1f01f (30:600:0x13)
[ 1.143604] ata1.00: configured for UDMA/66
[ 1.149515] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM_GSA-H40N RA00 PQ: 0 ANSI: 5
[ 1.149876] ata2: port disabled--ignoring
[ 1.297028] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.297032] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.633688] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.643352] firewire_ohci 0000:01:09.0: failed to read phy reg
[ 1.643576] firewire_ohci: probe of 0000:01:09.0 failed with error -16
[ 1.730033] usb 1-4: new low-speed USB device number 2 using ohci_hcd
[ 1.936808] usbcore: registered new interface driver usbhid
[ 1.936814] usbhid: USB HID core driver
[ 2.100049] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.107021] ata6.00: ATA-7: Hitachi HDS721616PLA380, P22OAB3A, max UDMA/133
[ 2.107025] ata6.00: 321672960 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.120325] ata6.00: configured for UDMA/133
[ 2.120524] scsi 5:0:0:0: Direct-Access ATA Hitachi HDS72161 P22O PQ: 0 ANSI: 5
[ 2.125055] sd 5:0:0:0: [sda] 321672960 512-byte logical blocks: (164 GB/153 GiB)
[ 2.125119] sd 5:0:0:0: [sda] Write Protect is off
[ 2.125123] sd 5:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.125149] sd 5:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.131113] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.131120] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.131457] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 2.146217] sda: sda1 sda2 sda3
[ 2.146831] sd 5:0:0:0: [sda] Attached SCSI disk
[ 2.206694] usb 1-8: new full-speed USB device number 3 using ohci_hcd
[ 2.407819] Initializing USB Mass Storage driver...
[ 2.408184] scsi6 : usb-storage 1-8:1.0
[ 2.408335] usbcore: registered new interface driver usb-storage
[ 2.408337] USB Mass Storage support registered.
[ 2.542664] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.014632] systemd[1]: Smack is not enabled in the kernel, not loading access rules.
[ 3.097131] systemd[1]: systemd 198 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 3.097800] systemd[1]: Set hostname to <acer-aspire>.
[ 3.352860] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 3.352959] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 3.352983] systemd[1]: Expecting device sys-subsystem-net-devices-enp3s0.device...
[ 3.353005] systemd[1]: Starting Remote File Systems.
[ 3.353024] systemd[1]: Reached target Remote File Systems.
[ 3.353041] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 3.353091] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 3.353108] systemd[1]: Starting LVM2 metadata daemon socket.
[ 3.353156] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 3.353173] systemd[1]: Starting Delayed Shutdown Socket.
[ 3.353206] systemd[1]: Listening on Delayed Shutdown Socket.
[ 3.353222] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 3.353253] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 3.353274] systemd[1]: Starting Journal Socket.
[ 3.353366] systemd[1]: Listening on Journal Socket.
[ 3.354821] systemd[1]: Starting Apply Kernel Variables...
[ 3.357143] systemd[1]: Mounting Huge Pages File System...
[ 3.363518] systemd[1]: Mounting POSIX Message Queue File System...
[ 3.370154] systemd[1]: Mounting Debug File System...
[ 3.385832] systemd[1]: Starting Journal Service...
[ 3.393610] systemd[1]: Started Journal Service.
[ 3.393800] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 3.393975] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 3.407359] systemd[1]: Started Set Up Additional Binary Formats.
[ 3.407389] systemd[1]: Starting Encrypted Volumes.
[ 3.407409] systemd[1]: Reached target Encrypted Volumes.
[ 3.407431] systemd[1]: Starting Setup Virtual Console...
[ 3.410492] systemd[1]: Starting udev Kernel Socket.
[ 3.410553] systemd[1]: Listening on udev Kernel Socket.
[ 3.410641] systemd[1]: Starting udev Control Socket.
[ 3.410689] systemd[1]: Listening on udev Control Socket.
[ 3.410760] systemd[1]: Starting udev Coldplug all Devices...
[ 3.417037] systemd[1]: Starting udev Kernel Device Manager...
[ 3.418761] scsi 6:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 3.436758] scsi 6:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 3.441505] systemd[1]: Started Load Kernel Modules.
[ 3.441546] systemd[1]: Mounted FUSE Control File System.
[ 3.441570] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 3.441652] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 3.441693] systemd[1]: Mounting Configuration File System...
[ 3.465751] scsi 6:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 3.476732] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 3.505747] scsi 6:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 3.516728] sd 6:0:0:1: [sdc] Attached SCSI removable disk
[ 3.549724] sd 6:0:0:2: [sdd] Attached SCSI removable disk
[ 3.553823] systemd[1]: Expecting device dev-disk-by\x2duuid-bb5a3cc3\x2d55fd\x2d4830\x2d8177\x2ddd32df9bd303.device...
[ 3.553856] systemd[1]: Mounting Temporary Directory...
[ 3.571730] sd 6:0:0:3: [sde] Attached SCSI removable disk
[ 3.744908] systemd-udevd[126]: starting version 198
[ 3.777101] systemd[1]: Started File System Check on Root Device.
[ 3.777142] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 3.790819] systemd[1]: Started udev Kernel Device Manager.
[ 3.800185] systemd[1]: Started Apply Kernel Variables.
[ 4.118718] EXT4-fs (sda2): re-mounted. Opts: data=ordered
[ 4.205364] systemd-journald[122]: Received SIGUSR1
[ 5.423026] thermal LNXTHERM:00: registered as thermal_zone0
[ 5.423033] ACPI: Thermal Zone [THRM] (40 C)
[ 5.463049] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 5.484558] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 5.484570] ACPI: Power Button [PWRB]
[ 5.484693] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 5.484697] ACPI: Power Button [PWRF]
[ 5.491085] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[ 5.542488] i2c i2c-0: nForce2 SMBus adapter at 0x1c00
[ 5.542524] i2c i2c-1: nForce2 SMBus adapter at 0xf400
[ 5.547898] Linux agpgart interface v0.103
[ 5.558914] ACPI: Fan [FAN] (on)
[ 5.559089] [drm] Initialized drm 1.1.0 20060810
[ 5.565468] microcode: AMD CPU family 0xf not supported
[ 5.567533] microcode: AMD CPU family 0xf not supported
[ 5.642735] wmi: Mapper loaded
[ 5.645076] kvm: Nested Virtualization enabled
[ 5.649689] powernow-k8: fid 0xb (1900 MHz), vid 0xc
[ 5.649696] powernow-k8: fid 0xa (1800 MHz), vid 0xd
[ 5.649699] powernow-k8: fid 0x2 (1000 MHz), vid 0x12
[ 5.649987] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ (2 cpu cores) (version 2.20.00)
[ 5.685561] checking generic (e0000000 130000) vs hw (e0000000 10000000)
[ 5.685568] fb: conflicting fb hw usage nouveaufb vs VESA VGA - removing generic driver
[ 5.685594] Console: switching to colour dummy device 80x25
[ 5.685773] nouveau 0000:00:0d.0: setting latency timer to 64
[ 5.686326] ACPI: PCI Interrupt Link [AIGP] enabled at IRQ 23
[ 5.686707] nouveau [ DEVICE][0000:00:0d.0] BOOT0 : 0x04c000a2
[ 5.686715] nouveau [ DEVICE][0000:00:0d.0] Chipset: C61 (NV4C)
[ 5.686722] nouveau [ DEVICE][0000:00:0d.0] Family : NV40
[ 5.687642] nouveau [ VBIOS][0000:00:0d.0] checking PRAMIN for image...
[ 5.733281] nouveau [ VBIOS][0000:00:0d.0] ... appears to be valid
[ 5.733287] nouveau [ VBIOS][0000:00:0d.0] using image from PRAMIN
[ 5.733560] nouveau [ VBIOS][0000:00:0d.0] BIT signature found
[ 5.733565] nouveau [ VBIOS][0000:00:0d.0] version 05.61.32.25.04
[ 5.733746] nouveau [ PFB][0000:00:0d.0] RAM type: unknown
[ 5.733749] nouveau [ PFB][0000:00:0d.0] RAM size: 128 MiB
[ 5.733752] nouveau [ PFB][0000:00:0d.0] ZCOMP: 0 tags
[ 5.761373] [TTM] Zone kernel: Available graphics memory: 443504 kiB
[ 5.761379] [TTM] Zone highmem: Available graphics memory: 709716 kiB
[ 5.761381] [TTM] Initializing pool allocator
[ 5.761831] nouveau [ DRM] VRAM: 125 MiB
[ 5.761838] nouveau [ DRM] GART: 512 MiB
[ 5.761844] nouveau [ DRM] BIT BIOS found
[ 5.761848] nouveau [ DRM] Bios version 05.61.32.25
[ 5.761852] nouveau [ DRM] TMDS table version 1.1
[ 5.761855] nouveau [ DRM] DCB version 3.0
[ 5.761859] nouveau [ DRM] DCB outp 00: 01000310 00000023
[ 5.761863] nouveau [ DRM] DCB outp 01: 00110204 98830003
[ 5.761865] nouveau [ DRM] DCB conn 00: 0000
[ 5.761869] nouveau [ DRM] DCB conn 01: 1131
[ 5.761872] nouveau [ DRM] DCB conn 02: 0110
[ 5.761875] nouveau [ DRM] DCB conn 03: 0111
[ 5.761877] nouveau [ DRM] DCB conn 04: 0113
[ 5.762420] nouveau W[ DRM] DCB type 4 not known
[ 5.762425] nouveau W[ DRM] Unknown-1 has no encoders, removing
[ 5.763281] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 5.763283] [drm] No driver support for vblank timestamp query.
[ 5.763931] nouveau [ DRM] 1 available performance level(s)
[ 5.763937] nouveau [ DRM] 0: core 425MHz shader 425MHz fanspeed 100%
[ 5.763939] nouveau [ DRM] c:
[ 5.765435] nouveau [ DRM] MM: using M2MF for buffer copies
[ 5.811870] sky2: driver version 1.30
[ 5.812122] ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
[ 5.812188] sky2 0000:03:00.0: Yukon-2 EC Ultra chip revision 2
[ 5.812268] sky2 0000:03:00.0: irq 43 for MSI/MSI-X
[ 5.812560] sky2 0000:03:00.0 eth0: addr 00:19:21:28:95:2d
[ 5.814804] composite sync not supported
[ 5.815267] nouveau [ DRM] allocated 1440x900 fb: 0x9000, bo f63fa000
[ 5.815425] fbcon: nouveaufb (fb0) is primary device
[ 5.829143] IT8726 SuperIO detected.
[ 5.829405] parport_pc 00:09: reported by Plug and Play ACPI
[ 5.829453] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 5.856121] ppdev: user-space parallel port driver
[ 5.877128] Console: switching to colour frame buffer device 180x56
[ 5.878923] nouveau 0000:00:0d.0: fb0: nouveaufb frame buffer device
[ 5.878929] nouveau 0000:00:0d.0: registered panic notifier
[ 5.878952] [drm] Initialized nouveau 1.1.0 20120801 for 0000:00:0d.0 on minor 0
[ 5.879707] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
[ 5.879730] hda_intel: Disabling MSI
[ 5.879786] snd_hda_intel 0000:00:05.0: setting latency timer to 64
[ 6.023710] systemd-udevd[151]: renamed network interface eth0 to enp3s0
[ 6.497697] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:02.0/usb1/1-4/1-4:1.0/input/input4
[ 6.498447] hid-generic 0003:093A:2510.0001: input,hidraw0: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:02.0-4/input0
[ 6.533068] Adding 997756k swap on /dev/sda3. Priority:-1 extents:1 across:997756k
[ 6.633135] sky2 0000:03:00.0 enp3s0: enabling interface
[ 6.633209] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 6.846889] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:05.0/input/input5
[ 7.603865] input: HDA NVidia Line as /devices/pci0000:00/0000:00:05.0/sound/card0/input6
[ 7.604089] input: HDA NVidia Front Mic as /devices/pci0000:00/0000:00:05.0/sound/card0/input7
[ 7.604265] input: HDA NVidia Rear Mic as /devices/pci0000:00/0000:00:05.0/sound/card0/input8
[ 7.604442] input: HDA NVidia Front Headphone as /devices/pci0000:00/0000:00:05.0/sound/card0/input9
[ 7.604616] input: HDA NVidia Line Out Side as /devices/pci0000:00/0000:00:05.0/sound/card0/input10
[ 7.604791] input: HDA NVidia Line Out CLFE as /devices/pci0000:00/0000:00:05.0/sound/card0/input11
[ 7.604969] input: HDA NVidia Line Out Surround as /devices/pci0000:00/0000:00:05.0/sound/card0/input12
[ 7.605141] input: HDA NVidia Line Out Front as /devices/pci0000:00/0000:00:05.0/sound/card0/input13
[ 8.208529] composite sync not supported
[ 8.244451] composite sync not supported
[ 8.450333] sky2 0000:03:00.0 enp3s0: Link is up at 100 Mbps, full duplex, flow control both
[ 8.450367] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
[ 20.811802] composite sync not supported
[ 23.142014] EXT4-fs (sda2): re-mounted. Opts: data=ordered,commit=0
[ 84.047784] usb 1-4: USB disconnect, device number 2
[ 85.606696] usb 1-4: new low-speed USB device number 4 using ohci_hcd
[ 85.814008] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:02.0/usb1/1-4/1-4:1.0/input/input14
[ 85.814445] hid-generic 0003:093A:2510.0002: input,hidraw0: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:02.0-4/input0
[ 389.250323] composite sync not supported
Xorg log:
[ 7.949]
X.Org X Server 1.14.0
Release Date: 2013-03-05
[ 7.949] X Protocol Version 11, Revision 0
[ 7.949] Build Operating System: Linux 3.8.2-1-ARCH i686
[ 7.949] Current Operating System: Linux acer-aspire 3.8.3-2-ARCH #1 SMP PREEMPT Sun Mar 17 13:38:16 CET 2013 i686
[ 7.949] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=bb82c8c9-614f-4ce3-85f2-3597507c391d ro quiet
[ 7.949] Build Date: 09 March 2013 11:46:22AM
[ 7.949]
[ 7.949] Current version of pixman: 0.28.2
[ 7.949] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 7.949] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 7.949] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Mar 21 15:06:46 2013
[ 7.988] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 8.001] (==) No Layout section. Using the first Screen section.
[ 8.001] (==) No screen section available. Using defaults.
[ 8.001] (**) |-->Screen "Default Screen Section" (0)
[ 8.001] (**) | |-->Monitor "<default monitor>"
[ 8.011] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 8.011] (==) Automatically adding devices
[ 8.011] (==) Automatically enabling devices
[ 8.011] (==) Automatically adding GPU devices
[ 8.060] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 8.060] Entry deleted from font path.
[ 8.060] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 8.060] Entry deleted from font path.
[ 8.060] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 8.060] Entry deleted from font path.
[ 8.060] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 8.060] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 8.060] Entry deleted from font path.
[ 8.060] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 8.060] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 8.060] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 8.060] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 8.069] (II) Loader magic: 0x825b620
[ 8.069] (II) Module ABI versions:
[ 8.069] X.Org ANSI C Emulation: 0.4
[ 8.069] X.Org Video Driver: 14.1
[ 8.069] X.Org XInput driver : 19.1
[ 8.069] X.Org Server Extension : 7.0
[ 8.069] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 8.072] (--) PCI:*(0:0:13:0) 10de:03d0:1019:2601 rev 162, Mem @ 0xfb000000/16777216, 0xe0000000/268435456, 0xfc000000/16777216, BIOS @ 0x????????/131072
[ 8.073] Initializing built-in extension Generic Event Extension
[ 8.073] Initializing built-in extension SHAPE
[ 8.073] Initializing built-in extension MIT-SHM
[ 8.073] Initializing built-in extension XInputExtension
[ 8.073] Initializing built-in extension XTEST
[ 8.073] Initializing built-in extension BIG-REQUESTS
[ 8.073] Initializing built-in extension SYNC
[ 8.073] Initializing built-in extension XKEYBOARD
[ 8.073] Initializing built-in extension XC-MISC
[ 8.073] Initializing built-in extension SECURITY
[ 8.073] Initializing built-in extension XINERAMA
[ 8.073] Initializing built-in extension XFIXES
[ 8.073] Initializing built-in extension RENDER
[ 8.073] Initializing built-in extension RANDR
[ 8.073] Initializing built-in extension COMPOSITE
[ 8.073] Initializing built-in extension DAMAGE
[ 8.073] Initializing built-in extension MIT-SCREEN-SAVER
[ 8.073] Initializing built-in extension DOUBLE-BUFFER
[ 8.073] Initializing built-in extension RECORD
[ 8.073] Initializing built-in extension DPMS
[ 8.073] Initializing built-in extension X-Resource
[ 8.073] Initializing built-in extension XVideo
[ 8.073] Initializing built-in extension XVideo-MotionCompensation
[ 8.073] Initializing built-in extension XFree86-VidModeExtension
[ 8.073] Initializing built-in extension XFree86-DGA
[ 8.073] Initializing built-in extension XFree86-DRI
[ 8.073] Initializing built-in extension DRI2
[ 8.073] (II) LoadModule: "glx"
[ 8.099] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 8.133] (II) Module glx: vendor="X.Org Foundation"
[ 8.133] compiled for 1.14.0, module version = 1.0.0
[ 8.133] ABI class: X.Org Server Extension, version 7.0
[ 8.133] (==) AIGLX enabled
[ 8.134] Loading extension GLX
[ 8.134] (==) Matched nouveau as autoconfigured driver 0
[ 8.134] (==) Matched nvidia as autoconfigured driver 1
[ 8.134] (==) Matched nv as autoconfigured driver 2
[ 8.134] (==) Matched nouveau as autoconfigured driver 3
[ 8.134] (==) Matched nvidia as autoconfigured driver 4
[ 8.134] (==) Matched nv as autoconfigured driver 5
[ 8.134] (==) Matched vesa as autoconfigured driver 6
[ 8.134] (==) Matched modesetting as autoconfigured driver 7
[ 8.134] (==) Matched fbdev as autoconfigured driver 8
[ 8.134] (==) Assigned the driver to the xf86ConfigLayout
[ 8.134] (II) LoadModule: "nouveau"
[ 8.134] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 8.154] (II) Module nouveau: vendor="X.Org Foundation"
[ 8.154] compiled for 1.14.0, module version = 1.0.6
[ 8.154] Module class: X.Org Video Driver
[ 8.154] ABI class: X.Org Video Driver, version 14.1
[ 8.154] (II) LoadModule: "nvidia"
[ 8.155] (WW) Warning, couldn't open module nvidia
[ 8.155] (II) UnloadModule: "nvidia"
[ 8.155] (II) Unloading nvidia
[ 8.155] (EE) Failed to load module "nvidia" (module does not exist, 0)
[ 8.155] (II) LoadModule: "nv"
[ 8.155] (WW) Warning, couldn't open module nv
[ 8.155] (II) UnloadModule: "nv"
[ 8.155] (II) Unloading nv
[ 8.155] (EE) Failed to load module "nv" (module does not exist, 0)
[ 8.155] (II) LoadModule: "vesa"
[ 8.156] (WW) Warning, couldn't open module vesa
[ 8.156] (II) UnloadModule: "vesa"
[ 8.156] (II) Unloading vesa
[ 8.156] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 8.156] (II) LoadModule: "modesetting"
[ 8.156] (WW) Warning, couldn't open module modesetting
[ 8.156] (II) UnloadModule: "modesetting"
[ 8.156] (II) Unloading modesetting
[ 8.157] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 8.157] (II) LoadModule: "fbdev"
[ 8.157] (WW) Warning, couldn't open module fbdev
[ 8.157] (II) UnloadModule: "fbdev"
[ 8.157] (II) Unloading fbdev
[ 8.157] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 8.157] (II) NOUVEAU driver
[ 8.157] (II) NOUVEAU driver for NVIDIA chipset families :
[ 8.157] RIVA TNT (NV04)
[ 8.157] RIVA TNT2 (NV05)
[ 8.157] GeForce 256 (NV10)
[ 8.157] GeForce 2 (NV11, NV15)
[ 8.157] GeForce 4MX (NV17, NV18)
[ 8.157] GeForce 3 (NV20)
[ 8.158] GeForce 4Ti (NV25, NV28)
[ 8.158] GeForce FX (NV3x)
[ 8.158] GeForce 6 (NV4x)
[ 8.158] GeForce 7 (G7x)
[ 8.158] GeForce 8 (G8x)
[ 8.158] GeForce GTX 200 (NVA0)
[ 8.158] GeForce GTX 400 (NVC0)
[ 8.158] (++) using VT number 7
[ 8.175] (II) [drm] nouveau interface version: 1.1.0
[ 8.175] (II) Loading sub module "dri"
[ 8.175] (II) LoadModule: "dri"
[ 8.175] (II) Module "dri" already built-in
[ 8.175] (II) NOUVEAU(0): Loaded DRI module
[ 8.175] (--) NOUVEAU(0): Chipset: "NVIDIA NV4c"
[ 8.175] (II) NOUVEAU(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 8.175] (==) NOUVEAU(0): Depth 24, (--) framebuffer bpp 32
[ 8.175] (==) NOUVEAU(0): RGB weight 888
[ 8.175] (==) NOUVEAU(0): Default visual is TrueColor
[ 8.175] (==) NOUVEAU(0): Using HW cursor
[ 8.175] (==) NOUVEAU(0): GLX sync to VBlank disabled.
[ 8.175] (==) NOUVEAU(0): Page flipping enabled
[ 8.175] (==) NOUVEAU(0): Swap limit set to 2 [Max allowed 2]
[ 8.208] (II) NOUVEAU(0): Output VGA-1 has no monitor section
[ 8.244] (II) NOUVEAU(0): EDID for output VGA-1
[ 8.244] (II) NOUVEAU(0): Manufacturer: ACR Model: ada8 Serial#: 1937803344
[ 8.244] (II) NOUVEAU(0): Year: 2007 Week: 38
[ 8.244] (II) NOUVEAU(0): EDID Version: 1.3
[ 8.244] (II) NOUVEAU(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
[ 8.244] (II) NOUVEAU(0): Sync: Separate Composite
[ 8.244] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 37 vert.: 23
[ 8.245] (II) NOUVEAU(0): Gamma: 2.20
[ 8.245] (II) NOUVEAU(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
[ 8.245] (II) NOUVEAU(0): Default color space is primary color space
[ 8.245] (II) NOUVEAU(0): First detailed timing is preferred mode
[ 8.245] (II) NOUVEAU(0): redX: 0.590 redY: 0.349 greenX: 0.328 greenY: 0.547
[ 8.245] (II) NOUVEAU(0): blueX: 0.155 blueY: 0.138 whiteX: 0.313 whiteY: 0.329
[ 8.245] (II) NOUVEAU(0): Supported established timings:
[ 8.245] (II) NOUVEAU(0): 720x400@70Hz
[ 8.245] (II) NOUVEAU(0): 640x480@60Hz
[ 8.245] (II) NOUVEAU(0): 640x480@67Hz
[ 8.245] (II) NOUVEAU(0): 640x480@72Hz
[ 8.245] (II) NOUVEAU(0): 640x480@75Hz
[ 8.245] (II) NOUVEAU(0): 800x600@56Hz
[ 8.245] (II) NOUVEAU(0): 800x600@60Hz
[ 8.245] (II) NOUVEAU(0): 800x600@72Hz
[ 8.245] (II) NOUVEAU(0): 800x600@75Hz
[ 8.245] (II) NOUVEAU(0): 832x624@75Hz
[ 8.245] (II) NOUVEAU(0): 1024x768@60Hz
[ 8.245] (II) NOUVEAU(0): 1024x768@70Hz
[ 8.245] (II) NOUVEAU(0): 1024x768@75Hz
[ 8.245] (II) NOUVEAU(0): 1152x864@75Hz
[ 8.245] (II) NOUVEAU(0): Manufacturer's mask: 0
[ 8.245] (II) NOUVEAU(0): Supported standard timings:
[ 8.245] (II) NOUVEAU(0): #0: hsize: 1280 vsize 720 refresh: 60 vid: 49281
[ 8.245] (II) NOUVEAU(0): #1: hsize: 1280 vsize 800 refresh: 75 vid: 3969
[ 8.245] (II) NOUVEAU(0): #2: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 8.245] (II) NOUVEAU(0): #3: hsize: 1440 vsize 900 refresh: 75 vid: 3989
[ 8.245] (II) NOUVEAU(0): Supported detailed timing:
[ 8.245] (II) NOUVEAU(0): clock: 106.5 MHz Image Size: 367 x 229 mm
[ 8.245] (II) NOUVEAU(0): h_active: 1440 h_sync: 1520 h_sync_end 1672 h_blank_end 1904 h_border: 0
[ 8.245] (II) NOUVEAU(0): v_active: 900 v_sync: 903 v_sync_end 909 v_blanking: 934 v_border: 0
[ 8.245] (II) NOUVEAU(0): Ranges: V min: 56 V max: 76 Hz, H min: 31 H max: 83 kHz, PixClock max 215 MHz
[ 8.245] (II) NOUVEAU(0): Monitor name: Acer AL1716W
[ 8.245] (II) NOUVEAU(0): Serial No: LA8040344303
[ 8.245] (II) NOUVEAU(0): EDID (in hex):
[ 8.245] (II) NOUVEAU(0): 00ffffffffffff000472a8ad50888073
[ 8.245] (II) NOUVEAU(0): 261101036c251778ee10d59759548c27
[ 8.246] (II) NOUVEAU(0): 235054bfee8081c0810f9500950f0101
[ 8.246] (II) NOUVEAU(0): 0101010101019a29a0d0518422305098
[ 8.246] (II) NOUVEAU(0): 36006fe510000006000000fd00384c1f
[ 8.246] (II) NOUVEAU(0): 5315000a202020202020000000fc0041
[ 8.246] (II) NOUVEAU(0): 63657220414c31373136570a000000ff
[ 8.246] (II) NOUVEAU(0): 004c41383034303334343330330a00aa
[ 8.246] (II) NOUVEAU(0): Printing probed modes for output VGA-1
[ 8.246] (II) NOUVEAU(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 +hsync +vsync (55.9 kHz eP)
[ 8.246] (II) NOUVEAU(0): Modeline "1440x900"x75.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "1280x800"x74.9 106.50 1280 1360 1488 1696 800 803 809 838 -hsync +vsync (62.8 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "1280x720"x60.0 74.44 1280 1336 1472 1664 720 721 724 746 -hsync +vsync (44.7 kHz)
[ 8.246] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e)
[ 8.246] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752I got again a total system freeze today when I wanted to launch firefox using only the openbox menu, without wbar running.
So I decided to try now the 'nouveau.noaccel=1' kernel command line parameter, and to use again wbar for my frequently used applis.
In the Xorg log, the differences are:
without 'nouveau.noaccel=1'
[ 30.761] (II) UnloadModule: "nv"
[ 30.761] (II) Unloading nv
[ 30.761] (--) Depth 24 pixmap format is 32 bpp
[ 30.762] (II) NOUVEAU(0): Opened GPU channel 0
[ 30.765] (II) NOUVEAU(0): [DRI2] Setup complete
[ 30.765] (II) NOUVEAU(0): [DRI2] DRI driver: nouveau
[ 30.765] (II) NOUVEAU(0): [DRI2] VDPAU driver: nouveau
[ 30.776] (II) EXA(0): Driver allocated offscreen pixmaps
[ 30.777] (II) EXA(0): Driver registered support for the following operations:
[ 30.777] (II) Solid
[ 30.777] (II) Copy
[ 30.777] (II) Composite (RENDER acceleration)
[ 30.777] (II) UploadToScreen
[ 30.777] (II) DownloadFromScreen
[ 30.777] (==) NOUVEAU(0): Backing store disabled
[ 30.777] (==) NOUVEAU(0): Silken mouse enabled
with 'nouveau.noaccel=1'
[ 1191.621] (II) UnloadModule: "nv"
[ 1191.621] (II) Unloading nv
[ 1191.621] (--) Depth 24 pixmap format is 32 bpp
[ 1191.621] (EE) NOUVEAU(0): Error creating GPU channel: -19
[ 1191.621] (EE) NOUVEAU(0): Error initialising acceleration. Falling back to NoAccel
[ 1191.621] (==) NOUVEAU(0): Backing store disabled
[ 1191.621] (==) NOUVEAU(0): Silken mouse enabled
[ 1191.621] (==) NOUVEAU(0): DPMS enabled
So now 3D acceleration is disabled.
I will see now if the system is stable enough for my daily usage and gives satisfactory performances.
I am almost sure that the mesa nouveau dri driver is the cause of the freezes.
Last edited by berbae (2013-03-27 10:07:42) -
Setting up a RAID of system drives
hello everyone,
I am looking to add a second system drive for more hd space. I was planning on purchasing a second Raptor and setting up a RAID 0. will I need to format my existing drive, or can I just plug in the new drive and set up my RAID in DU?
...any feedback appreciated, thanks.
Dual-core PwrPC 2.0ghz G5 2mb RAM Mac OS X (10.4.6)Ok,
You already have a Raptor as boot, most likely it's a 36 or 74GB with 8 MB cache and it's hooked up to your internal SATA ports.
To create a RAID O, you must match the two drives exactly. Erase w/Zero both of them, create the RAID O set in Disk utility and clone your boot drive back from a booted external drive using cloning software. (meaning you have to first clone the original to a external then boot from it and clone to the RAID O)
Problem: Western Digital has updated all their drives with a new SATA spec, also increased the cache to 16 MB. The PowerMac's can't handle the new SATA spec (supposedly the Quad can, but I'm hearing mixed stories)
So unless you find a 8MB cache Raptor, your going to need to spend more money.
The solution if your determined to have RAID O Raptors, is to buy two of them, preferably the new 10,000 RPM 16MB cache 150GB ones, and a Firmteck SATA PCI card (the only one that's bootable off of) with 4 internal SATA ports and 4 external ports. Then hook the internal Raptors to that.
The Firmteck card will also give you the option of hooking up external SATA drives in a powered enclosure, one cable to each drive. So you can expand if you wish.
With a RAID O, you must clone (for a whole boot drive) or backup (for files) quite regularly, like at least once a week for clone and daily backup for files. Since one should be doing this anyway, it's really no big deal. Because like the other poster said, RAID O is a bit more risky, one drive goes you lose all data as the data path is split. But the speed is worth it. So with a pair of 150GB Raptors your going to need a 250-300GB drive external Firewire 800/400 drive.
Now to keep a drives performance up, you shouldn't fill it more than 50%, and certainly shouldn't fill a boot drive more than 80%. So one can use a 250GB external drive for clone backup as long as the data on the 300GB RAID O doesn't go over around 240GB. (80%) Get it?
LaCie makes a good Firewire 800/400/USB d2 drive.
However if this is a bit too much to bear on your wallet, then what you can do is reduce what you have on the boot Raptor below 50% by moving just what you have in documents, pictures, movies and audio files into NEW folders on a second internal SATA drive (preferably one with 16MB cache not from Western Digital)
Once you have slimmed up your Raptor, then clone the whole drive to a external drive, option boot from it and make sure everything works correctly, repair permissions and test all software (some copy protected ones will need to be fixed). Once your are 100% certain it's ok, then Erase w/Zero the Raptor and clone the whole drive back.
What this will do is optimize the Raptor boot drive drive, free up disk space, de-fragment large files/apps and sort of tighten everything up to the most fastest part of your boot drive, the outer tracks, in the good part of the 50% side of your drive. (vs the inner tracks where performance starts to suffer)
Without the space hogging files that are now on the second SATA drive, your drive freshly optimized, the arm in the hard drive has less space to travel to get your data that Mac OS X, apps and random music files iTunes needs to constantly access.
Now I suggest using Carbon Copy Cloner to do your optimizations with, because I know how this program clones drives, in alphabetical order on the main directory of your boot drive. So Applications, Developer (if you have installed Developers Tools from Tiger install disk) Library, System and finally Users at the end (where it could expand without de-optimizing your drive)
Always follow these rules when cloning.
1: Don't run or do anything else while a cloning process is going on.
2: Always Disk utility Erase w/Zero option all new drives one time or in the case of a security issue.
3: Option boot from the clone and check it out.
4: Repair permissions BEFORE and AFTER each cloning.
5: Avoid partial clones because of copy protection schemes hiding files on the drive.
6: Avoid cloning to partitions, especially on the same drive, because if the drive fails mechanically your screwed out of your clone as well. Keep it a boot clone to a boot clone on a separate drive.
7: If you can keep two clones of your boot drive, just in case you get hacked or have a exploit, because when you hook up the second clone, it will get owned too and possibly erased. If this happens, C boot off the installer disk (write protected) and Erase w/Zero all infected drives and disconnect from the internet/network before hooking up that last clone.
I wrote a book, I hope it helps.
Note to others: Firmteck SATA PCI card will not work in PCI-Expressed based PowerMac's.
http://www.amug.org/amug-web/html/amug/reviews/articles/firmtek/1eve4/ -
Nvidia doesn't exist in /proc/modules
After running pacman -Syu (I should have blocked the nvidia & nvidia-utils packages from upgrading...), X won't start with nvidia and resolution only goes to 800x600 in vesa.
So I tried going to a completely minimal xorg.conf file with the bare minimums in order to rebuild my settings. I am getting this error:
ERROR: Module nvidia does not exist in /proc/modules
In order to use the new nvidia module, exit Xserver and unload it manually.
Xserver isn't running, as I am sitting on the command line, so not sure where to go from here.
Here is my output of pacman -Qs nvidia:
local/nvidia-96xx 96.43.13-2
NVIDIA drivers for kernel26, 96xx branch.
local/nvidia-96xx-utils 96.43.13-1
NVIDIA drivers utilities and libraries, 96xx branch.
I am using a GeForce 420Go on my old laptop, so it uses the old 96xx driver. This was working perfectly before the package upgrade.
Thoughts?derekr44 wrote:
Will as soon as I can get back to the command line. X is stuck on a black screen and ctrl-alt-bkspc doesn't shut it down...
CD drive doesn't work, so booting from a CD is out. This old laptop doesn't boot via USB, so that's out too.
Anyone have any ideas how I can get to the command line in order to try toxygen's suggestion?
Ctrl+Alt+F1 to get to a console. If that doesn't work, which seems likely, then do a hard reboot and add 3 to the end of your kernel command line in GRUB. (If you start a login manager via DAEMONS in rc.conf, you'll need to add 1 or S to the command line instead). -
Booting to Nvidia Raid......HELP pls!
I am starting a new installation on a K8n Neo4 Platinum PCB(1).
I am trying use 2 WD 250 GB Sata 2's as a mirrored boot drive.
I enabled the Nvidia raid in bios, enabled the SATA ports, booted & entered the Nvidia RAID format, set my drives as mirrored & boot. Then rebooted.
I am installing windows 2000 Pro SP4. At the prompt I enter [F6] & installed the supplied diskette. Pressed S when prompted & loaded both drivers. I then get a stop error during windows installation.
Tried again with only 1 driver, same thing, then the other driver, same thing.
The Disc says WINXP so I replaced the HD & went to the internet, DL's the Win 2000 drivers & repeated the installation.
Same thing.
What can I do?Quote from: selkov on 13-May-06, 00:50:44
I do have the unused SATA ports turned off.
Will try that when I get home.
Spoke with MSI this moring there response was "DUH?".
Given all the probs with SATA-2 you might want to jumper the drives to SATA-1, at least until the install is done. I'd also run the WD Diags first to make sure the drives are recognized and can be written/read through BIOS. -
I using nVidia RAID 1 Mirror setup and am wondering if there is any way to get metrics such as error counts, drive failure etc in Windows XP. Is there a software applications or does the firmware provide any hints as to the performance(Health) of the drives? My drives are WD Raptors.
Bob...
Problem solved. BIOS 1.5 two times flashed and CMOS reset. New installation went fine (and better than the tens before). -
Diamond Plus Nvidia RAID problem
Hello. I was able to set up nvidia raid in the BIOS and XP accepted the 2 drivers (F6) during install. However, when it gets to the point of formatting the array, Windows says it can't format the drive(s), "...maybe broken, etc." So, I tried the onboard Silicon Image raid and that worked fine. Windows installed without a problem. The only thing that bothered me was that HD Tach showed Burst Speed for the array as disappointingly slow. Actually, a few ticks less than the single ATA 150 drive they use for comparison. Every report I've seen with the Hitachi drives in raid 0 has them bursting above 300 mbs. But, the average read was an acceptable 97 mbs.
So, I got rid of the raid array and installed Windows on a single drive. Burst speed is 221 (a lot higher than with the SI RAID), but average read, naturally, is much less at around 47.
Questions: 1) Any suggestions on the problem I'm having with Nvidia Raid? I'd give it another try if there is a solution.
2) Is RAID 0 really worth it? I'm mainly interested in gaming and everything I've read says there is no real world difference playing games with Raid 0.
BTW, the system is very stable either way (Raid/Single Drive). Prime 95 & memtest, no errors after 4/6 hours.Quote
Do I also need to load the SATA IDE driver after/before the 2 Raid drivers?
Both drivers need to be loaded for OS to se the array as one disk . You must do this with nvidia SATA raid .
Use the "S" a second time and load the second driver during the F6 install . -
Hello All:
I have an MSI K8N SLI Platinum (7100 Rev 1.0) board.
It is running the 3.10 BIOS, using a 3800+ X2 'Manchester' rev E4 CPU and 2x1 GB of Geil 3-4-4-8 RAM.
Radeon 300 GPU (yeah, I was pinching pennies when I bought that one).
Seasonic 500 W PSU.
No OC - everything plane jane.
Cool 'n Quiet enabled
Presently I am running XP Pro SP2 and have the following drives:
2 x WDC WD740GD Raptor 74 ('SATA I') - non-raid on SATA 1&2, boots off SATA 1.
2 x WDC2500KS ('SATA II') on SATA 3&4 set up as a Nvidia Raid 0
2 x Seagate Cheetah .8 series 250 GB ('SATA II') on SATA 5&6 set up as SiI Raid 0
This rig runs fine, with very nice benchmarks for the Raid units (well north of 100 MB/s) and good reliability (no RAID disasters [yet]). I mostly use it for Photoshop.
I have tried running Photoshop under WinXP64 on another box (MSI 7207) with 2 x 1 GB RAM ans a 'Venice' 3500+ CPU and have seen nice increases in speed in many functions. However, this system does not have the Raid setup that the K8N SLI Pt has.
So I have been trying to get XP64 to install on the 7100 (K8N SLI Pt) machine.
I do the dance of two floppies with the NVidia RAID and SiI Raid drivers during install and set XP64 up on the second Raptor on SATA 2. (XP Pro is on the onther one on SATA 1).
When XP64 boots the machine hangs. I can boot into 'Safe Mode' but running MSCONFIG and disabling all the driver loading does not help - it still crashes when I boot XP64 in anything besides 'Safe Mode.'
I have tried an install w/o any of the RAID drivers and got a stable SP64 boot.
I ran MS Update and got all the relevant XP64 updates (my install disk is SP1, which is the latest SP for XP64).
I then installed the SiI drivers using Device Manager - that worked OK. Nice box, Photoshop CS2 ran well, the SiI RAID gave nice benchmarks, etc.
I then installed the Nvidia RAID drivers using Device Manager - dead box with the same issues as above.
I have also tried an install with the SiI RAID drivers only and also got a stable SP64 boot and a dead box when I installed the Nvidia RAID drivers using Device Manager.
All drivers are all the most recent release (no Betas) downloaded off the MSI site, with the Nvidia RAID set dated 8/1/2005.
Right now I'm blaming the Nvidia RAID drivers, but am open to suggestion.
Anybody had experience with XP64 on this setup?
Thanks,
ssTo clarify:
The rig in question (in the post above) is:
MSI K8N SLI Platinum (7100 Rev 1.0) board.
3.10 BIOS
CPU AMD Athlon64 X2 3800+ 'Manchester' rev E4 CPU
2x1 GB of Geil 3-4-4-8 RAM dual channel DDR 400
Radeon 300 GPU
Seasonic 500 W PSU.
No OC - everything plane jane.
Cool 'n Quiet enabled
Stable operation under XP Pro SP2 with the drives set up as follows:
2 x WDC WD740GD Raptor 74 ('SATA I') - non-raid on SATA 1&2, boots off SATA 1.
2 x WDC2500KS ('SATA II') on SATA 3&4 set up as an Nvidia RAID 0
2 x Seagate Cheetah .8 series 250 GB ('SATA II') on SATA 5&6 set up as SiI RAID 0
This mobo uses an Nforce 4 SLI chipset. I believe the Neo 2 Pt uses an Nforce 3 chipset.
Yes, I am using the latest MSI-sourced drivers with the XP64 installs.
The question is: has anyone gotten Nforce 4 SLI chipset Nvidia RAID to work with XP64?
ss -
Problems w/ on-board NVidia RAID + PCI RAID on P7N Diamond
Here's the setup and issue.
I'm booting off of the on-board NVidia RAID on my P7N Diamond. It's RAID5 w/ 4 WD 640GB drives. Works fine.
I've recently pulled a NetCell SyncRAID SR5000 PCI RAID card (runs an adapted RAID3) from an old system where it worked fine and was NOT the boot drive...just storage. Plugged it in the one and only PCI slot on my P7N Diamond. Once it's in, the system will no longer boot.
When the PCI RAID card is not installed, the mobo's BIOS boot menu shows "NVIDIA RAID5 1". As soon as I install the PCI RAID card, the NVidia RAID disappears (no longer an option at all) and is replaced by "IDE:Revolution". At that point the system cannot find any bootable source and fails.
I also get an error message "Not Enough Space to Copy PCI Option ROM".
Unfortunately, MSI's tech support is passing the buck on this one. They're saying:
Then sound like the card and the board sata controller are not compatible. If the card is connected it disable the onboard SATA controller. Once the card install the port is enable again. please check with the card manufacture. thanks
I really find this annoying as the card works just fine in other systems. It's having an issue WITH THIS MOTHERBOARD, but they tell me to go to the card manufacturer. The real problem is NetCell went out of business a few years ago, so they're not available to go to.
So, the quick and dirty is the manufacture of the only motherboard I've had a problem with concerning this card won't help, and the card manufacture cannot be reached. I'm hoping someone here may come up with a workaround.
I'm trying to consolidate down to 1 computer, and I specifically purchased a case and power supply with this RAID migration in mind. I'm gunna be PISSED if I can't use a RAID array I spent close to a grand for (a couple years ago)!MSI continues to blame the chipset or PCI card for the incompatibility (not the motherboard), saying there's nothing they can do.
Does ANYONE have an idea other than setting aside my RAID array? -
F10 for nVIDIA RAID BIOS doesnt work.
Like many others I am trying to set up a SATA 1/2 Raid on my MSI NEO2 Platinum 54-G using two WD-Raptors 74Gig.
I've read the FAQ's about how to set up the Raid Array.
So I set up the drives on SATA ports 1 and 2 in the bios (following the instrunctions in the FAQ) and they are recognised under 'Standerd CMOS Feature' in the BIOS.
When it came to rebooting and then pressing F10 to access the 'nVidia Raid BIOS'-so that I could enable Raid 0 stripping on the chosen drives.
I find that I cant get into that part of the BIOS no matter how early or how often I press the F10 button. The system just simply goes past that point as I havn't pressed anything.
I'm using a MS Natural Multimedia Keyboard and don't see why this is happening. I even tried upgrading the BIOS to version 1.2 but still can't access the 'nVidia Raid BIOS' when I press F10 when it asks me to.
Is any one else having this problem? or Knows how to get around it?usb keyboard does not work for me either for holding down insert to clear overclock. I have to use a ps/2 keyboard for that.
also with usb keyboard i have to press del to enter setup rapidly, with ps/2 i only have to press once. also perfectdisk offline defrag wont start as it cant find a keyboard.
Its all very weird as the keyboard works in bios and dos.
There is an option in bios under integrated peripherals for "legacy usb keyboard support" or something to that effect. try it at enabled. (doesnt help me) -
K8N - nVidia RAID - RAID5 no Rebuild
I have a MSI K8N Diamond Plus MB, one 300GB boot drive + a 4*400GB RAID5 array. One of the drives developed a bad block fault, a real one, confirmed by the Samsung HUTIL. I removed drives from my 4-disk RAID5 array until I found the faulty one and sent it in for warranty repair/replacement.
In the meantime I used a spare 500GB drive as the fourth drive in the array. I had everything backed up, and went on according to the User's Guide. I had downloaded the latest drivers/utilities from the MSI site, and it seemed like the program was more recent than the manual, so I downloaded a more recent manual as well. They still didn't match, and the available menu selections weren't that "hot", but having backups I continued anyway. I ended up with an array declared healthy, everything looked fine - but the files were corrupt. So it was delete array / reinitialize / restore from backup...
Now I have gotten a new 400GB disk as warranty replacement and switched it for the 500GB temp disk. Immediately when I replaced the faulty disk with the factory new one, it was added to the RAID5 array - and shown as Healthy. Never was it shown "Rebuilding", and with a TB of data it would take some time... When I checked I could in Mediashield select to rebuild any of the four disks - except the one that needed rebuilding!
One could hope that it's automatically rebuilt in the background, as the drive was automatically added to the array, but I checked with Task Manager and nothing goes on in the background using CPU cycles.
The RAID5 array immediately showed up as Healthy, not degraded as when there was a faulty disk or no disk there. As I mentioned, it never showed "Rebuilding"... I have let the computer stay on for (right now) 18 hours.
I guess the only thing to do now is to remove the connectors from another drive and see if it shows Healthy, Degraded or not usable at all (I boot from another, non-RAID disk). If it shows Degraded, I can test some RAR files on the volume. If they're corrupt, the new disk isn't rebuilt. The problem then is that it doesn't seem to be any way to force it to be rebuilt...
Newer boards with newer versions of NVRaidman/MediaShield have menu items for removing a single drive from an array, but not here. And I guess trying to DL and use nForce4 drivers/utilities from nVidia is risky, maybe something MSI-specific stops working altogether...
First, one 401LJ went bad. Array shows as Degraded, disk as Faulty.
Then, after a factory new 403LJ was added, the RAID5 array immediately shows as Healthy. When "RAID5" or any of the 401LJ drives are selected, all five menu choices are available (Hot Plug, Rebuild, Convert Array, Remove Array, Sync Array).
If the 403LJ is selected, "Rebuild" is gone.
If I anyway try to rebuild by clicking on RAID5->Rebuild, I can only chose from the 401LJ drives when selecting which to rebuild. Not the 403LJ that needs rebuilding...
As far as I know I have the latest version of the MSI utilities. The NvRaidMan program shows with tool-tip to be 5.10.2600.552 (the MSI site indicates 5.50 or something), the latest nVidia has seems to be much more recent. But it's a scary thing to even think of testing if installing the nVidia "6.86_nforce_win2kxp_international_whql. exe"...
Any ideas/help?
Maybe it helps to mark that specific drive in BIOS as a non-RAID drive and reboot, then another reboot and change that back... Maybe that will force rebuild or let me select that.I neither think Samsung knows nor cares. The 401LJ uses three 133GB platters, the 403LJ three 166GB platters with 33GB unused on each (a way of being able to use 503LJ drives that didn't make QC), seems closer than the 501LJ with four 133GB platters.
However, I just managed to trigger a Rebuild - we'll see how it goes. Should take about 25-30 hours, if not the timeframe mentioned in different forums is measured on a slower computer than mine (or faster).
What I did (I believe the first step was unnecessary, but I wanted to make it into as many steps as possible):
* Stopped the PC and removed the SATA connector from the new 403LJ drive. Rebooted and the array was degraded.
* Stopped PC again and replaced the SATA connector. Removed the 403LJ from the list of RAID drives in BIOS, started XP again.
* 403LJ showed up as a standard SATA drive, reformatted it and rebooted PC again.
* In BIOS, changed back the 403LJ to be a RAID drive, showed up in MediaShield as a second, faulty drive. Now we're back onto known territory...
* Deleted the faulty one-drive RAID and the 403LJ now became a Free Drive.
* Hot-plugged the RAID5 array, the 403LJ was added to it, Rebuild started automatically.
While I wrote this, the rebuild has reached 15%. No, I don't write that slow, seems like rebuilding is much faster on a current computer. Or it's a non-linear function.
Edit: 100% now, first tests indicates everything is alright -
G-Raid external hard drive won't mount -- have tried almost everything!
My iMac (Intel , OSX 10.4.11) has been happily working with my G-Raid external hard drive for over a year. But now, after the computer cord was disconnected yesterday, it refuses to mount the G-Raid or recognize it anywhere. Can't find it in the Disk Utilities or under "About this mac -- Firewire." Called Apple service and tried everything the agent recommended...PRAM diagnostic reboot, power surge, plugging, unplugging...nothing helped. The problem isn't with the G-Raid, which works fine plugged into my old Powerbook with the same firewire. Grateful for any help, as I really need the G-Raid -- it's got all my projects, music, photos....
Can you plug it in with a USB cable on your iMac? That might get you through your crisis and even resurrect your Firewire connection. Accidentally breaking the connection on my external Firewire drives happens too often as the connector doesn't make a snug fit compared to USB. It's not a problem unless there was something in your buffers at the time the connection was broken. You may need to Repair the drive using Disk Utility when it eventually reconnects or all may be well without more intervention.
-
Can you swap existing drives into new MacPro tower?
I have an old MacPro silver tower with 1.3GHz processors in it and not a lot of RAM. My buddy has a slightly newer one that looks the same but with I think 2.6GHz processors and a lot more RAM. He said I could have his except for the hard drives because he got a new Mac, but I'm wondering, if he gives me his, can i just take all the drives out of mine and put them in his drive-less machine in the same slots they exist in in mine, and everything should work right? or does it not work like that
There never was a Mac Pro 1,1 or any other that had 1.3GHz (but it did have 1300MHz front side bus, with 2.0 - 2.66 - 3.0GHz processor)
About this Mac.... or system profile.
Yes you can use your drives though you probably need to use his drive bay sleds.
Any Mac Pro other than the new current model can run 10.6.x or Lion. -
Mac Mini with RAID - 4x USB Drives
I've got an older Mac mini 2007 Core 2 Duo machine that isn't doing much since I got the MacBook so I thought about using it to replace my Windows Server.
I did want to have some form of redundancy attached to this server so I hoped to use 4 USB drives of 4tb capacity. I hoped to use two drives "doubled up" to get the capacity I needed (8tb) and another two to "mirror" the first two for redundancy.
I'm aware that OSX has RAID partitioning available but wondered if what I want to do is possible, has anyone tried this setup?Thanks both for your thoughts.
I'm now having a rethink myself as USB2 does have limitations I want to avoid, and have come up with options:
A new Mac mini with USB3/Thunderbolt to speed up the throughput (I will be using it to stream HD to Apple TV, for the iPhoto Library and for Time Machine Backups) on which I would use either a Direct Attached Storage solution with RAID 5
or
A standalone NAS box. Is there a NAS that could do all three jobs? I guess it would have to natively format HFS+ because of iPhoto...and have an iTunes server and be Time Machine compatible. A tall order?
Thoughts?
Maybe you are looking for
-
Hi Friends, I am running Payables Open Interface Import to load invoices from invoice interface table in R12. But I am facing below error: MSG-00883: After Repport Trigger: Setting the Org Context to Multiple I have done below steps further to fix my
-
How use the method hasPermission in weblogic server 6.1
Hello everybody ! In my application web ,i restrict access to some ressources (some jsp) to some specified groups . So,i create permissions in the file web.xml , as indicated in the doc 6.0 . For example only the user : system can access to all the j
-
hello forumers. i bumped into a post about flash cs6 and adobe has created a wish list gaining propositions about its next suite.so is there a wish list for illustrator c6???? this link is for the wish list for flash users just to get an idea http://
-
Intermittent of error "ORA-12203: TNS:unable to connect to destination"
Hi, One of my application (run 24 hours each day) face intermittent of error "ORA-12203: TNS:unable to connect to destination", any one face the same issue ? any solution for this ? The error may occur weekly, some time monthly, occur randomly. My Or
-
How to change file type from .zip to .dock
I would like to know how to change the saved file type (.zip) to other file types such as (.txt), (.doc), (.dock) or (.pdf).