NW2004s SPS13 RFC rfconnect fails

Hi all,
I am running a sample rfc program on solaris m/c.
SAP server details
2004s SPS13
I am using a communication user to connect to server using RFC SDK.
If i connect to the server with password in smaller case it gives aerror message
"Name or password is incorrect"
But if i give the password in capital case,it works fine.
BAsically i have to create a user with acapital password to work fine on SPS13
ON SPS12 it worked fine for lower case password.
Best Regards
Manoj

check the password settings in your instance profile using tx. RSPFPAR. check for settings with 'pass' in it.

Similar Messages

  • Error in START_SHDI_FIRST... RFC logon fails

    Hello All,
    I cannot get past a step in the enhancement package 4  installation.  The step is called:  START_SHDI_FIRST. The error says to troubleshoot by looking at 2 logs,  STARTSFI.LOG  and DEVTRACE.log.   extracted below.
    The problem can be described this way. The step begins as the installer tries to start the shadow system.   The first attempt stopped and I could see that the shadow was not started.  I used the information in note 525677 to manually start the shadow and could verify that it was starting. 
    The screen says to retry until I can logon to the shadow.   I am able to logon as user SAP* with password pass in client 000.   I am not able to logon as myself and receive the message: Logon not possible (error in license check). 
    As SAP* I use the transaction SLICENSE, and could see that the maintenance certificate had expired. I loaded that certificate without an error.
    I also see that the hardware key information is missing.  SAP* is not allowed to update that information.
    I believe that no other user will be able to logon as long as the license is an issue.   The installer is trying to do a remote logon to verify that the system is up (my interpretation) .
    I also see this information in the shadow system dev_W1 log.
    M  *** ERROR => ThMsGetHardwareId: ThOpcodeToMsg failed (1) [thxxmsg.c    3095]                                                                
    M  ***LOG Q16=> ThGetMsHwId, DpMBufHwIdGet (HWID_PENDING) [thxxmbuf.c   511]                                                                   
    M  *** ERROR => SlicLikeyGetHardwareKey: no hwid from MSG server: -1 [sliclikey.c  1301]                                                       
    M  *** ERROR => likey_get_validity_dates: Error getting the hardware key. You might find some information in file "dev_ms" on the message server
    M                                                                               
    M Thu Jul 29 15:18:28 2010                                                                               
    M  *** ERROR => ThCheckReqInfo: message send/receive failed [thxxhead.c   17580]                                                               
    M                                                                               
    M  Modeinfo for User T8/M1                                                                               
    So, am I correct in seeing that the missing hardware key is the problem in the shadow system?   Any ideas would be appreciated,  otherwise I will clear the systems out and start over.  Thanks.
    Pat.
    Below is the DEVTRACE   (extract)
    Directory:  /usr/sap/TEH/EHPI/abap/log
    Name:       DEVTRACE.LOG
    trc file: "dev_disp.new", trc level: 1, release: "701"
    sysno      15
    sid        TEH
    systemid   324 (IBM iSeries with OS400)
    relno      7010
    patchlevel 0
    patchno    69
    intno      20020600
    make:      single threaded, ASCII, 64 bit, optimized
    pid        103802
    Thu Jul 29 14:54:58 2010
    kernel runs with dp version 243(ext=110) (@(#) DPLIB-INT-VERSION-243)
    length of sys_adm_ext is 364 bytes
    SWITCH TRC-HIDE on ***
    ***LOG Q00=> DpSapEnvInit, DPStart (15 103802) [dpxxdisp.c   1287]
         shared lib "dw_xml.so" version 69 successfully loaded
         shared lib "dw_xtc.so" version 69 successfully loaded
         shared lib "dw_stl.so" version 69 successfully loaded
         shared lib "dw_gui.so" version 69 successfully loaded
         shared lib "dw_mdm.so" version 69 successfully loaded
    rdisp/softcancel_sequence :  -> 0,5,-1
    use internal message server connection to port 3615
    MtxInit: 30000 0 0
    Thu Jul 29 14:54:59 2010
    MBUF state OFF
    DpCommInitTable: init table for 500 entries
    rdisp/queue_size_check_value :  -> off
    ThTaskStatus: rdisp/reset_online_during_debug 0
    EmInit: MmSetImplementation( 2 ).
    MM global diagnostic options set: 0
    <ES> client 0 initializing ....
    <ES> InitFreeList
    <ES> block size is 4096 kByte.
    Using implementation std
    <ES> Info: use normal pages (no huge table support available)
    EsStdUnamFileMapInit: ES base = 0x7000000b0000000
    EsStdInit: Extended Memory 4096 MB allocated
    <ES> 1023 blocks reserved for free list.
    ES initialized.
    mm.dump: set maximum dump mem to 96 MB
    Thu Jul 29 14:55:00 2010
    WARNING => System running without ICM - check rdisp/start_icman [dpxxdisp.c   13279]
    DpSetProcessPriority: Run priority for work process startup adjusted to 20
    DpSetProcessPriority: Run priority for work process startup adjusted to 20
    Thu Jul 29 14:55:01 2010
    rdisp/http_min_wait_dia_wp : 1 -> 1
    ***LOG Q0I=> NiPConnect: connect (79: Connection refused) [nixxi.cpp 2519]
    ERROR => NiPConnect: SiConnect failed for hdl 2 / sock 9
        (SI_ECONN_REFUSE/79; I4; ST; 10.127.0.100:3615) [nixxi.cpp    2519]
    ERROR => MsIAttachEx: NiBufConnect to omni/3615 failed (rc=NIECONN_REFUSED) [msxxi.c      652]
    ***LOG Q0L=> DpLoopInit, nomscon () [dpxxdisp.c   1816]
    Thu Jul 29 14:55:19 2010
    CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
    Thu Jul 29 14:55:53 2010
    ***LOG Q0I=> NiPConnect: connect (79: Connection refused) [nixxi.cpp 2519]
    ERROR => NiPConnect: SiConnect failed for hdl 3 / sock 10
        (SI_ECONN_REFUSE/79; I4; ST; 10.127.0.100:3615) [nixxi.cpp    2519]
    ERROR => MsIAttachEx: NiBufConnect to omni/3615 failed (rc=NIECONN_REFUSED) [msxxi.c      652]
    Thu Jul 29 14:56:34 2010
    ERROR => MsISnd2: not_attached [msxxi.c      1321]
    ***LOG Q0N=> DpRqNoWpHandle, MsSndName () [dpxxdisp.c   5007]
    trc file: "dev_ms", trc level: 1, release: "701"
    [Thr 01] Thu Jul 29 14:54:56 2010
    [Thr 01] MsSOsPrivInit: Run priority adjusted to 12
    [Thr 01] MsSSetTrcLog: trc logging active, max size = 20971520 bytes
    systemid   324 (IBM iSeries with OS400)
    relno      7010
    patchlevel 0
    patchno    63
    intno      20020600
    make:      multithreaded, ASCII, 64 bit, optimized
    pid        103801
    [Thr 01] ***LOG Q01=> MsSInit, MSStart (Msg Server 1 103801) [msxxserv_mt. 1853]
    [Thr 01] Thu Jul 29 14:54:57 2010
    [Thr 01] SigISetDefaultAction : default handling for signal 20
    [Thr 01] ***LOG Q0I=> NiIBindSocket: bind (67: Address already in use) [nixxi.cpp 3239]
    [Thr 01] *** ERROR => NiIBindSocket: SiBind failed for hdl 1 / sock 7
        (SI_EPORT_INUSE/67; I4; ST; 0.0.0.0:3615) [nixxi.cpp    3239]
    [Thr 01] *** ERROR => MsSCommInit: NiBufListen(3615) (rc=NIESERV_USED) [msxxserv_mt. 10222]
    [Thr 01] *** ERROR => MsSInit: MsSCommInit (internal) [msxxserv_mt. 1903]
    [Thr 01] *** ERROR => main: MsSInit [msxxserv_mt. 5983]
    [Thr 01] ***LOG Q02=> MsSHalt, MSStop (Msg Server 103801) [msxxserv_mt. 6030]
    trc file: "dev_rd", trc level: 1, release: "701"
    Thu Jul 29 14:55:00 2010
    Shared memory semaphore administration area size = 10608
    Thu Jul 29 14:55:06 2010
    ***LOG S00=> GwInitReader, gateway started ( 103807) [gwxxrd.c     1758]
    systemid   324 (IBM iSeries with OS400)
    relno      7010
    patchlevel 0
    patchno    68
    intno      20020600
    make:      single threaded, ASCII, 64 bit, optimized
    pid        103807
    gateway runs with dp version 243(ext=110) (@(#) DPLIB-INT-VERSION-243)
    gateway (version=701.2009.09.28)
    gw/local_addr : 0.0.0.0
    CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
    CCMS: Initalizing shared memory of size 40000000 for monitoring segment.
    Thu Jul 29 14:55:09 2010
    CCMS: Checking Downtime Configuration of Monitoring Segment.
    Bind service sapgw15 (socket) to port 3315
    GwPrintMyHostAddr: my host addresses are :
      1 : [10.127.0.100] omni (HOSTNAME)
      2 : [127.0.0.1] LOOPBACK (LOCALHOST)
    Full qualified hostname = omni.plastekgroup.com
    DpSysAdmExtCreate: ABAP is active
    DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active
    MtxInit: -2 0 0
    Thu Jul 29 14:55:47 2010
    GwDpInit: attached to gw_adm at 700000080599e90
    Thu Jul 29 14:55:48 2010
    DpSetProcessPriority: Run priority for gwrd adjusted to 12
    AN EXTRACT OF STARTSFI_LOG
    Directory:  /usr/sap/TEH/EHPI/abap/log
    Name:       STARTSFI.LOG
    1 ETQ201 Entering upgrade-phase "START_SHDI_FIRST" ("20100729145436")
    2 ETQ367 Connect variables are set for standard instance access
    4 ETQ399 System-nr = '14', GwService = 'sapgw14'
    4 ETQ399 Environment variables:
    4 ETQ399   dbs_db4_schema=<null>
    4 ETQ399   auth_shadow_upgrade=<null>
    4 ETQ399 Set environment for standard connect:
    4 ETQ399 ENV: dbs_db4_schema=SAPR3
    4 ETQ399 ENV: auth_shadow_upgrade=0
    4 ETQ399 Set RFC variables for standard connect:
    4 ETQ399 System-nr = '14', GwService = 'sapgw14'
    4 ETQ399 Set tool parameters for standard connect:
    4 ETQ399   default TPPARAM: DEFAULT.TPP
    1 ETQ206 Executing pre-phase DB specific actions.
    1 ETQ206 Executing pre-phase DB specific actions.
    1 ETQ200 Executing actual phase 'MAIN_SHADOW/START_SHDI_FIRST'.
    1 ETQ399 Phase arguments:
    2 ETQ399 Arg[0] = 'DEVTRACE.LOG'
    4 ETQ399 Set environment for shadow connect:
    4 ETQ399 ENV: dbs_db4_schema=SAPR3
    4 ETQ399 ENV: auth_shadow_upgrade=1
    4 ETQ399 Set RFC variables for shadow connect:
    4 ETQ399 System-nr = '15', GwService = 'sapgw15'
    4 ETQ399 Set tool parameters for shadow connect:
    4 ETQ380 computing toolpath for request "TP_SHADOW_CONNECT"
    4 ETQ381 request "TP_SHADOW_CONNECT" means "tp needs to connect to shadow system"
    4 ETQ382 translates to group "R3UP_TOOL_GROUP_NEW"
    4 ETQ383 translates to path "exe"
    4 ETQ383 translates to path "exe"
    4 ETQ399   default TPPARAM: SHADOW.TPP
    4 ETQ380 computing toolpath for request "TP_ALWAYS_NEW"
    4 ETQ381 request "TP_ALWAYS_NEW" means "always tp from DIR_PUT/exe, for phase KX_SWITCH"
    4 ETQ382 translates to group "R3UP_TOOL_GROUP_NEW"
    4 ETQ383 translates to path "exe"
    4 ETQ383 translates to path "exe"
    2 ETQ399 Starting shadow instance
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2 ETQ399 Stopping shadow instance
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    2 ETQ231 RFC Login failed
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    2 ETQ231 RFC Login failed
    2 ETQ353 Starting system
    3 ETQ399 Executing command: 'startsap  SID(TEH) INSTANCE(15) PROFILE('/usr/sap/TEH/EHPI/abap/TEH/SYS/profile/START_DVEBMGS15_omni')'.
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-1"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-1"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-1"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-1"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-1"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-1"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="TEH", Nr="15", GwHost="omni", GwService="sapgw15"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-1"
    2EETQ399 Starting shadow instance failed
    2EETQ399 Test RFC failed finally

    Hi,
    You are getting this error because your hardware key in the license installed in slicense is wrong. Since upgrade tries to login with ddic user and if there is problem with license then only SAP* user is allowed.
    Please perform below steps to resolve the problem. Check at OS level what is the hardware key, if the hardware key that is present in slicense is different then generate a permanent license of that hardware key and apply it in shadow instance. After that check whether you are able to login with user other than SAP*, if yes, then repeat the phase.
    Please perform above steps and let us know the result.
    Thanks
    Sunny

  • RFC logon failed with message: Failed: Connect to SAP  gateway failed

    I installed CI instance fine and i am stopped here with this error at the end of DB instance install. Could someone let me know what could  be the reason for this. Is there any fix or workaround to continue the install.
    INFO       2006-09-16 01:13:02 [iaxxrfcimp.cpp:398]
              CAbRfcImpl::setRfcConnectParam
    RFC parameter ASHOST set to value hostSAP.
    INFO       2006-09-16 01:13:02 [iaxxrfcimp.cpp:398]
              CAbRfcImpl::setRfcConnectParam
    RFC parameter SYSNR set to value 09.
    INFO       2006-09-16 01:13:02 [iaxxrfcimp.cpp:543]
              CAbRfcImpl::checkConnectInfo
    RFC connection information checked successfully.
    ERROR      2006-09-16 01:13:02 [iaxxrfcimp.cpp:450]
              CAbRfcImpl::openRfcConn
    FRF-00007  Unable to open RFC connection.
    ERROR      2006-09-16 01:13:02
              CJSlibModule::writeError_impl()
    FRF-00063  RFC logon failed with message: Failed: Connect to SAP  gateway failed
    Connect_PM  GWHOST=hostSAP, GWSERV=sapgw09, ASHOST=hostSAP, SYSNR=09
    LOCATION    CPIC (TCP/IP) on local host
    ERROR       partner not reached (host hostSAP, service 3309)
    TIME        Sat Sep 16 01:13:02 2006
    RELEASE     640
    COMPONENT   NI (network interface)
    VERSION     37
    RC          -10
    MODULE      nixxi_r_mt.cpp
    LINE        8528
    DETAIL      NiPConnect
    SYSTEM CALL connect
    ERRNO       146
    ERRNO TEXT  Connection refused
    COUNTER     4
    Thanks,
    Ram

    at the end of the database instance installation SAPInst is doing some RFCs to the CI.
    The logfile states that the gateway on host hostSAP with the systemnumber 09 is not reachable.
    Please check if you have started the central instance on this machine.
    peter

  • RFC call failed: JCO.Server could not find server function 'SET_SLD_DATA'

    Hi, All
    the system is PI 7.0 EHP1 oraclei Win2003 server, I configured SLD but I run RZ70, having error "RFC call failed: JCO.Server could not find server function 'SET_SLD_DATA' ". I know there are lot of tread about this error, but none of themsolve my problem. all JCO, RFC connections and SDL DATA supplier(VA) seem OK. error message in SM21 is "Could not send SLD data"
    detail from SM21
    The system could not send the data that has been collected automatical
    for the System Landscape Directory (SLD). Check whether the gateway
    configured in transaction RZ70 has been started and whether the SLD
    bridge has been registered with this gateway.
    You can use transaction SM59 to check this in the sending system for t
    implemented RFC destinations. The RFC destinations have the standard
    names "SLD_UC" for Unicode sending systems and "SLD_NUC" for non-Unico
    sending systems. If a different RFC destination has been entered in
    RZ70, check this destination instead.
    You can use the Gateway Monitor to check the target gateways. In ABAP
    systems, this monitor is started with transaction SMGW, or you can use
    the external SAP program "gwmon". Check whether the specified gateway
    has an active registration.
    OF COURSE I checked  RFC of  SLD_UC and SMGW
    any different ideas
    Regards
    ABH

    Hi
    Please check the following notes are implemented
    Note 906454                           
    Note 907729
    You may be aware but if you are not --->RZ70 creates the required SLD* RFCs during runtime - therefore if you have defined these RFCs manually first using the same namespace you can get RFC conflicts which result in a failed submission    
    Please also check the user in the RFC is known to both systems and has required authorization to write to SLD
    Generally with SLD you have to install or select a suitable gateway to handle incoming data supply traffic
    Also the gateway you are using has be known to SLD and reflected in RZ70 - i.e these defintions have to be the same
    It is also recommended to delete all references to SLD_* RFCs in data supplier and target SLD
    after a failed submission attempt to allow RZ70 to recreate these consistently once the above has been checked
    Best wishes
    Stuart

  • First RFC call failed, config not loaded. Check the System landscape configuration.

    Dear Experts,
    We are getting below error on portal while using the BEX query in BI system.
    Error:
    BEx Web Application
    Error: First RFC call failed, config not loaded. Check the System landscape configuration.
    Exception occurred while processing the current request; this exception cannot be handled by the application or framework
    Failed to process request; contact your system administrator
    To facilitate analysis of the problem, keep a copy of this error page
    We are sorry for the inconvenience.
    As the ITS & WEB AS connection tests go successful on object created for BI system in portal.
    Kindly suggest me on this issue..
    Thanks,
    Bharath.

    Hi Bharath,
    Please go through the below SAP Note and let me know if this helps.
    1903392 - Error: First RFC call failed, config not loaded
    BR,
    Anurag

  • RFC call failed : Error when opening an RFC connection

    Hi,
    As a result of "Start Data Collection" operation in the t-code RZ70, I have got this error.
    "RFC call failed : Error when opening an RFC connection"
    Others things are with success message.
    Regards,
    Bala Raja

    hi
    check this links
    http://help.sap.com/saphelp_nw04s/helpdata/en/9b/da0f41026df223e10000000a155106/frameset.htm
    http://help.sap.com/saphelp_nw04s/helpdata/en/9b/da0f41026df223e10000000a155106/frameset.htm
    also check Tcode: SLDAPICUST.
    run tcode SLDCHECK? any error?
    Thanks
    Rodrigo
    PS: If useful reward points

  • Connect from SAP gateway to RFC server failed - Java StandAlone app X SAP RAC System

    Dears,
    I'm developing a Java application (RFC SERVER) with JCo3 and I need to connect to SAP RAC system.
    I have configured the TCP/IP connection via transaction SM59, but when I try to start my server I face the error below (dev_jco_rfc.trc):
    ==========================================================================================
    **** Error file opened at 20140714 112024 Brasilia Time Rel 3.0.10 (2013-08-08) [720.440]
    Error:  >Mon Jul 14 11:20:24,636<    RfcException: [null]
        message: Connect from SAP gateway to RFC server failed
    Connection parameters: TYPE=A DEST=VSPAGUE ASHOST=cpe1601 SYSNR=01 SAPROUTER=/H/155.56.49.28 PCS=1
    LOCATION    SAP-Gateway on host ld7624.dmzwdf.sap.corp / sapgw01
    ERROR       hostname 'cpe1601' unknown
    TIME        Mon Jul 14 16:20:25 2014
    RELEASE     740
    COMPONENT   NI (network interface)
    VERSION     40
    RC          -2
    MODULE      /bas/740_REL/src/base/ni/nixxhl.cpp
    LINE        193
    DETAIL      NiHLGetNodeAddr: hostname cached as unknown
    COUNTER     3
        Return code: RFC_FAILURE(1)
        error group: 102
        key: RFC_ERROR_COMMUNICATION
    ==========================================================================================
    This problem happens when my app executes the line:
    JCoServer myServer = JCoServerFactory.getServer(myServerName);
    My system properties:
    jco.client.lang=EN
    jco.destination.peak_limit=10
    jco.client.client=800
    jco.client.passwd=********
    jco.client.user=********
    jco.client.sysnr=01
    jco.destination.pool_capacity=3
    jco.client.ashost=/H/155.56.49.28/H/cpe1601
    jco.server.connection_count=3
    jco.server.gwhost=/H/155.56.49.28/H/cpe1601
    jco.server.progid=VSPAGUE
    jco.server.gwserv=sapgw01
    jco.server.repository_destination=VSPAGUE
    Using SAP Logon i can connect to server cpe1601 system E16 without problems.
    Please, I really need some help, because my knowledge on SAP platform is minimum.

    Hi Markus,
    Changing ASHOST=ld7624.dmzwdf.sap.corp as you have suggested, I got the error message: Connect to SAP gateway failed ...
    As you could see, the host I'm connecting is from SAP RAC Service.
    Here in our company we have only SAP Logon and my RFC Application, and I can connect to SAP remote system via SAP Logon with this settings:
    System Connection Parameters
    Description: SAP ECC 6.0
    Application Server: cpe1601
    Instance Number: 01
    System ID: E16
    SAProuter String: /H/155.56.49.28/H/
    Below the connection information I received from SAP RAC SUPPORT for testing purposes:
        E16 System:
        SID: E16
        Client: 800
        System Number: 01
        Server: cpe1601
        Component Version: SAP ERP Central Component 6.0 Enhancement Pack 6 Suite on HANA
        User: ********
       Password: ********
       SAProuter String:
       If you don't plan to use SAPRouter at your end,
       /H/155.56.49.28/H/    

  • Crystal report- Connect from SAP gateway to RFC server failed

    Hi All,
    I am trying to connect to a SAP R3 system from crystal reports but it gives me below error.
    Please note : Transports have been imported and also the roles CRYSTAL_ENTITLEMENT and CRYSTAL_DESIGNER. My user is a member of these roles which were release along with Best practice reports v1.31
    Error :
    Logon failed.
    Details: CMALLC : rc= 27 > Connect from SAP gateway to RFC server failed
    Connect_pm GWHOST=10.10.4.63, gwserv=SAPGW30, SYSNR= 30
    Location SAP-gateway on host ply.log.com/sapgw30
    Error timeout during allocate
    TIME ....
    Release 700
    Component SAP Gateway
    Version 2
    RC 242
    Module gwr3cpic.c
    LINE 1996
    Detail no connect of TP sapdb30 from host 10.10.4.63 after 20 sec
    Can you please help us solving this error.
    Thanks
    Chetan

    Hi Stratos,
    The SAP Version is ECC 6.0.
    The below transports have been imported.
    u2022 Open SQL Connectivity transport (K900574.r21 and R900574.r21)
    u2022 Info Set Connectivity transport (K900575.r21 and R900575.r21)
    u2022 Row-level Security Definition transport (K900576.r21 and R900576.r21)
    u2022 Cluster Definition transport (K900585.r21 and R900585.r21)
    u2022 Authentication Helpers transport (K900578.r21 and R900578.r21)
    Thanks & Regards,
    Chetan

  • Connect from SAP gateway to RFC server failed

    Good day and a happy new year to you all!
    I am failing to connect to my SAP BW system from BEx. The logon fails with this message:
    >>>>>Start<<<<<<<<<<
    Error Group
    RFC_ERROR_COMMUNICATION
    Message
    Connect from SAP gateway to RFC server failed
    Connect_PM  GWHOST=10.16.64.77, GWSERV=sapgw02, ASHOST=10.16.64.77, SYSNR=02
    LOCATION    SAP-Gateway on host bwsys / sapgw02
    ERROR       timeout during allocate
    TIME        Sat Dec 31 13:16:19 2005
    RELEASE     640
    COMPONENT   SAP-Gateway
    VERSION     2
    RC          242
    MODULE      gwr3cpic.c
    LINE        1785
    DETAIL      no connect of TP sapdp02 from host 10.16.64.77 after 22 sec
    COUNTER     2
    >>>>>>>>>END<<<<<<<<<<<<
    I only experience this problem when connecting using any BEx component, but, I can successfully connect to the SAP BW system from SAP gui.
    Additionally, I have the service 'sapdp02' defined in the services file, both on the workstation and the server.
    What could be wrong or missing in my configuration?
    Regards,
    Joao.

    hi Joao,
    check if oss note 447882 relevant
    you may ask basis for help
    Symptom
    You want to access the customer system using the BEx Analyzer.The connenction fails:The system displays the error RFC_ERROR_COMMUNICATION.In the detail screen, the system displays message "Partner not reached" (host 192.168.4.2, service sapgw 00).
    Other terms
    SAP Gateway, RFC_ERROR_COMMUNICATION, partner not reached
    Reason and Prerequisites
    The SAP gateway host is deactivated or the TCP/IP port 33xx (where xx corresponds to the system number) is not open.
    Solution
    Issue statement ping <IP address> (In this example:192.168.4.2) No reply: Boot SAP Gateway host required.
    An answer:Check whether the TCP/IP port 33xx is open (where xx corresponds to the system number) and start the SAP gateway.
    The TCP/IP port is also partially defined in the services file as an sapgw<SID> or sapgwxx entry (where xx corresponds to the system number). The services file is in the Windows directory or in WinNT/System32/drivers/etc.

  • Error: Connect from SAP gateway to RFC Server failed

    Hi
    I am trying to connect SAP server using the java (JCO connection), and getting following error. While I am able to connect to the same sever using SAP Logon pad with the same ipaddress (hostname) and logon credentials.
    Please kindly help.
    Erro: Connect from SAP gateway to RFC server failed.
    Connect_PM GWHOST = hostname, GWSER = sapgw03, ASHOST=hostname, SYSNR=03
    LOCATION  SAP-Gateway on host hostname / sapgw03
    ERROR       timeout during allocate
    TIME Wed Oct 31 05:31:45 2007
    RELEASE 640
    COMPONENT SAP-Gateway
    VERSION 2
    RC 242
    MODULE gwr3cpic.c
    LINE 1795
    DETAIL no connect of TP sapdp03 from host hostname after 22 sec
    COUNTER 3

    Hi K Patil,
    Acording to me you are faceing this issue because the entry of your backend System is not in the SLD (System Landscape Directory ) of your server.
    to make this work you have to make entry in the SLD of your server
    fort that plesae acess this link.
    Re: JCo connection Error
    Re: wt is SLD.. how to do configure it
    Please Reward Points if Helpfull.
    Regards
    Vinit
    Edited by: Vinit Soni on Dec 19, 2007 7:20 AM

  • Unable to connect to SAP gateway to RFC server failed(hostname unknow)

    Hi All,
    I am trying to create a new Model(to connect to SAP R/3 server) using the following steps:
    1.Selecting Import Adaptive RFC Model
    2.Entering Model name,package,default logical system names
    3.Selecting the single server option and giving the details of the SAP R/3 server.
    When I try to connect it gives me the following error :
    -Connect from SAP gateway to RFC server failed.
    Also it mentions :
    <b>"ERROR hostname 'sapR3' unknown "</b>
    Where <b>sapR3</b> is the entry corresponding to the IP address in the host file.
    Further I am able to establish a telnet session using the same hostname in command prompt.
    I have searched the Internet for solutions, but I haven't found any yet.Any ideas?
    Regards,
    Kshitij Agrawal

    Hi,
    Please check if the hostname that you specify in the "Reimport Model" GUI of NWDS matches with the application server name specified in your R/3 system.The same can be verified by following three simple steps:
    1) Open the SAP LogOn.
    2) Choose the server to which you wanted to connect and right click on it to get the "properties" in the context menu.
    3) Look for the value entered in the field "Application Server" in the properties window.
    Hope this helps.

  • FRF-00063  RFC logon failed with message: Failed: Connect to SAP gateway fa

    We are getting below error while installing CRM 4.1 on oralce,sunsolaris.
    ERROR      2007-09-27 01:19:46
               CJSlibModule::writeError_impl()
    FRF-00063  RFC logon failed with message: Failed: Connect to SAP gateway failed
    Connect_PM  GWHOST=uapkb2dh, GWSERV=sapgw29, ASHOST=uapkb2dh, SYSNR=29
    LOCATION    CPIC (TCP/IP) on local host
    ERROR       partner not reached (host uapkb2dh, service 3329)
    TIME        Thu Sep 27 01:19:46 2007
    RELEASE     640
    COMPONENT   NI (network interface)
    VERSION     37
    RC          -10
    MODULE      nixxi_r_mt.cpp
    LINE        8642
    DETAIL      NiPConnect
    SYSTEM CALL connect
    ERRNO       146
    ERRNO TEXT  Connection refused
    COUNTER     2
    Regards,
    Madhu.

    We are getting below error while installing CRM 4.1 on oralce,sunsolaris.
    ERROR      2007-09-27 01:19:46
               CJSlibModule::writeError_impl()
    FRF-00063  RFC logon failed with message: Failed: Connect to SAP gateway failed
    Connect_PM  GWHOST=uapkb2dh, GWSERV=sapgw29, ASHOST=uapkb2dh, SYSNR=29
    LOCATION    CPIC (TCP/IP) on local host
    ERROR       partner not reached (host uapkb2dh, service 3329)
    TIME        Thu Sep 27 01:19:46 2007
    RELEASE     640
    COMPONENT   NI (network interface)
    VERSION     37
    RC          -10
    MODULE      nixxi_r_mt.cpp
    LINE        8642
    DETAIL      NiPConnect
    SYSTEM CALL connect
    ERRNO       146
    ERRNO TEXT  Connection refused
    COUNTER     2
    Regards,
    Madhu.

  • RFC connection failed - When using code created by "GENERATE PHP" button

    Hi All,
    I can use the saprfc_test.php to login, call a BAPI and return data from SAP. But on the same BAPI screen if I click the generate php button and copy the new .php file into my /htdocs/saprfc folder and execute it the browser it returns with "RFC connection failed"
    I am totally stuck, please can anybody help?
    Rob.

    I needed to specify "MSHOST"=>"",    Its strange that this was not neccessary for interactive scripts but the problem is solved

  • SAP Installation RFC LOGON FAILED- SQl ERROR ON PROGRAM SPAM (SAPMSSY1)

    Dear Gurus,
    during the SAP installation, i got the RFC logon failed error: SQL Error on program SPAM (SAPMSSY1)
    I am pasting the disp_w0 file.....................
    http://www.4shared.com/file/89058633/ac7a0547/_2__dev_w0.html
    pls let me know the how to lovve this.
    the basic error is like....
    Generating ABAP/4 Program SAPMS380                                .
    A  Source SAPMS380                                 Line 8.
    A  Error Code GEN_SOURCE_FORMAT.
    A  Module  $Id: //bas/620/src/krn/gen/screads.c#7 $ SAP.
    A  Function sc_getstring Line 624.
    A  Error when reading program SAPMS380
    Its showing this kinda error for a max of program like SAPMSSY1, SAPMSSY2, SAPMS380 and lots more which are clearly depicted in disp_w0 file.
    what is the error??? is there any error in program SAPMSSY1??
    if this is true pls let me know hot to solve this? where i can access this SAPMSSY1 ?? remember i can not use any T-code like SE36 as my installation is not finished.
    Kindly have a detail look on the disp_w0 file.
    Abhishek

    HI
    can u tell me how 2 acces the ABAP program like SAPMSSY1 etc. without entering into SAP by T-code.
    as i can not login right now. i want to do certain changes in these programs.
    Abhishek

  • RFC Reimporting failed

    Hi,
    during a reimporting process model, the system return to me this dump :
    <i>
    com.sap.ide.metamodel.importers.rfcmodel.RFCImportFailedException: RFC Import failed. Cause: class java.lang.NullPointerException:null
    java.lang.NullPointerException
         at com.sap.ide.metamodel.importers.rfcmodel.DynamicRFCModelImporter.ImportRFC(DynamicRFCModelImporter.java:316)
         at com.sap.ide.metamodel.importers.rfcmodel.DynamicRFCModelImporter.doImport(DynamicRFCModelImporter.java:196)
         at com.sap.ide.metamodel.importers.rfcmodel.reimport.DynamicRFCModelReimporter.doImport(DynamicRFCModelReimporter.java:331)
         at com.sap.ide.metamodel.importers.rfcmodel.reimport.DynamicRFCModelReimporter.getImportLog(DynamicRFCModelReimporter.java:264)
         at com.sap.ide.webdynpro.modeleditor.wizards.model.creation.ModelWizard$11.run(ModelWizard.java:1344)
         at org.eclipse.jface.operation.ModalContext.runInCurrentThread(ModalContext.java:302)
    </i>
    oddly, I can reimport a model with three bapi inside, but that dump appear for a model with broadly 9 BAPIs.
    Regards

    Hi Berthe,
    That`s the reason why it is recommended to keep model in a separate DC.
    Backup you WD project. Try to delete model files (*.wdmodel, *.wdmodelclass, *.dtlogicalddic, *.dtsimpletype and related *.dtsimpletype.xlf) physicaly from file system. Open NWDS,  make "Reload" ("ReloadRebuild") and import model again. Make sure that the model name is still thee same! Restart NWDS, make "Reload" ("ReloadRebuild") for WD project. If neccessary right click on controller (component, custom or view) and select "Repair".
    Best regards, Maksim Rashchynski.

Maybe you are looking for