NX-OS 6.2 Cannot specify interface vlan as source-interface for logging
I have the following config on Catalyst:
logging source-interface Vlan1024
I want to be able to specify an interface vlan as the source-interface on NX-OS. The only option I can get is to use a loopback interface as the source-interface, but I want to specify an SVI. Is that possible with NX-OS?
NEXUS-7710(config)# logging source-interface ?
loopback Loopback interface
Hello
AppleWorks is bundled with only SOME machines, the iBook, iMac G5, eMac and macMini.
Of course, as the media used is a DVD with a huge capacity, the app is stored on the support wher the operating system SPECIFIC to the machine is also stored.
But this implies NO link with the two products.
AppleWorks 6 was carbonised in a hurry to show that the thing was do-able.
My point of view is that it was done assuming that a replacement app would be available quickly. So, stick to human guidelines was certainly not a priority.
In fact, what was thought to be a short period beame a long one because Mac OS X needed a lot of time to become a sufficiently stable basis on which Apple was able to build a successor to AppleWorks and, as we all know, the successor named iWork is far from a complete product. There is nothing like a spreadsheet or a database tool.
So, we have to continue to use our old fashioned AppleWorks (which is also, for many of us an old friend whith sympathetic wrinkles.)
Yvan KOENIG (from FRANCE lundi 30 janvier 2006 19:00:44)
Similar Messages
-
[switchport port-security mac ] on [interface VLAN n?]
Hello,
did anyone tried to use the command [switchport port-security mac-address n?] on [interface VLAN n?] ? (for example in a 2950).
I don't have the material to make that test, and I am not sure if it works or not.
Many thanks!Hi,
Switchport port-security as the name implies is to be configured on switchport. VLAN interface on the switch is a routed interface and hence, you can't apply any switchport configuration on it and that includes, port security.
HTH
Sundar -
EoMPLS over interface VLAN on 7600??
Hi all,
I ve read EoMPLS will not work on interface VLAN's in 7600 series routers... Is it for any specific IOS bug (if so is the same be fixed?) or the platform itsefl will not support...
Because we have an EoMPLS customer who is not able to work on interface VLAN..
Thanks in advance....I got the below message as well:
LAB-R5-7604-CDAC-II(config-if)#mpls ip
MPLS CONFIG on LAN NOT RECOMMENDED: Cross-connect is currently configured
on interface vlans and WAN interfaces are facing the MPLS core.
By configuring MPLS on LAN interfaces, AToM on vlan interfaces may be non
functional.
LAB-R5-7604-CDAC-II(config-if)#mpls mtu 1546 -
Interface vlan does not up!
Hi all,
I create a vlan follows an interface vlan, but the interface vlan does not up.
I'm using RSP7600 Adv IP Service with ES20 line card. Please help.
Thanks million!Hello,
A SVI interface for a VLAN X will be up/up if there is an access port alive in the VLAN X on the switch, or if there is a trunk port alive on the switch on which the VLAN X is allowed. Are these requirements met in your particular case?
Best regards,
Peter -
MGRE in VRF and Source Interface Issue
friends,
I have a scenario where i need to use multiple multi-point GRE tunnels and put them in VRF for each customer. The problem i am facing is that for each Tunnel i use Routers loopback in global table as source address. It works fine for one Tunnel. But as soon as i create another tunnel using the same loopback as source. Both tunnels go down. If i use different loopback addresses for each tunnel, all tunnels stays up. Can anyone tell me why i cannot use one loopback as source-address for all tunnels?? creating indiviual loopback for each tunnel doesn't seem scalable.
interface Tunnel0
ip vrf forwarding RED
ip address 10.0.0.1 255.255.255.0
no ip redirects
ip nhrp map 10.0.0.4 172.16.1.4
ip nhrp map 10.0.0.5 172.16.1.5
ip nhrp network-id 1
tunnel source Loopback0
tunnel mode gre multipoint
end
interface Tunnel1
ip vrf forwarding BLUE
ip address 11.0.0.1 255.255.255.0
no ip redirects
ip nhrp map 11.0.0.6 172.16.1.6
ip nhrp network-id 2
tunnel source Loopback1
tunnel mode gre multipoint
end
interface FastEthernet0/0
description *** Connected to Customers for mGRE ***
ip address 172.16.1.1 255.255.255.0
end
interface Loopback0
ip address 1.1.1.254 255.255.255.255
endHello
Can you provide show interface tunnel
Harish -
What is the idea behind specifying the voice VLAN under the interface
Hi,
What is the idea behind specifying the voice VLAN under the interface? (Is it needed for both 802.1P and 802.1Q?)
Regards
MThe voice vlan command is what tells the IP phone what VLAN it should use...
The idea is that setting the native vlan on the port controls what VLAN the attached PC goes into, and the voice vlan tells the phone which VLAN it should go into.
It doesn't have any direct relation to QoS, as the port could be configured to ignore or take action on QoS markings with or without the voice vlan command.
Aaron -
RV180 Router: Cannot get Inter-VLAN Routing to work.
I have been banging at this now for two days and just cannot get Inter-VLAN routing working to work on this router.
Here is the est-up:.
Upgraded to latest Cisco firmware (1.0.1.9).
Starting with factory default settings, I added 2 VLANS as follows:
vlan default(id=1): dhcpmode=server IP=192.168.1.1/24 port 1
vlan vlan2 (id=2): dhcpmode=server IP=192.168.2.1/24 port 2
vlan vlan3 (id=3): dhcpmode=server IP=192.168.3.1/24 port 3
(unconnected)
WAN port
|
Routing/NAT
|
vlan ip 192.168.1.1 192.168.2.1 192.168.3.1
vlan name default vlan2 vlan3
vlan id ID=1 ID=2 ID=3
Inter-VLAN Routing No Yes Yes
Port 1 Untagged Excluded Excluded
Port 2 Excluded Untagged Excluded
Port 3 Excluded Excluded Untagged
Port 4(not of interest) Untagged Excluded Excluded
Port 1 Port 2 Port 3
| | |
AdminPC PC2 PC3
192.168.2.191 192.168.3.181
PC2 gets assigned an IP Address of 192.168.2.191 (DGW=192.168.2.1) - OK
PC3 gets assigned an IP Address of 192.168.3.181 (DGW=192.168.3.1) - OK
PC2 with (IP 192.168.2.191) can ping 192.168.2.1 and 192.168.3.1 - OK
PC3 with (IP 192.168.3.181) can ping 192.168.3.1 and 192.168.2.1 - OK
BUT....
PC2 cannot ping PC3 - NOT WORKING
PC3 cannot ping PC2 - NOT WORKING
(does not work in both Gateway Mode and Router Mode)
ANYONE CAN HELP ME FIGURE OUT WHY ??????
Your help is much appreciated.
I bought this device specifically because it supported inter-VLAN routing!.
Venu
Supporting Information:
Screen captures:
VLAN Membership:
VLAN ID Description Inter VLAN Device Port 1 Port 2 Port 3 Port 4
Routing Mgment
1 Default Disabled Enabled Untagged Excluded Excluded Untagged
2 VLAN2 Enabled Enabled Excluded Untagged Excluded Excluded
3 VLAN3 Enabled Enabled Excluded Excluded Untagged Excluded
Multiple VLAN Subnets:
VLAN ID IP Address Subnet Mask DHCP Mode DNS Proxy Status
1 192.168.1.1 255.255.255.0 DHCP Server Enabled
2 192.168.2.1 255.255.255.0 DHCP Server Enabled
3 192.168.3.1 255.255.255.0 DHCP Server Enabled
Routing Table (Gateway Mode)
Destination Gateway Genmask Metric Ref Use Interface Type Flags
127.0.0.1 127.0.0.1 255.255.255.255 1 0 0 lo Static UP,Gateway,Host
192.168.3.0 0.0.0.0 255.255.255.0 0 0 0 bdg3 Dynamic UP
192.168.2.0 0.0.0.0 255.255.255.0 0 0 0 bdg2 Dynamic UP
192.168.1.0 0.0.0.0 255.255.255.0 0 0 0 bdg1 Static UP
192.168.1.0 192.168.1.1 255.255.255.0 1 0 0 bdg1 Static UP,Gateway
127.0.0.0 0.0.0.0 255.0.0.0 0 0 0 lo Dynamic
Routing Table (Router Mode)
(Same)cadet alain, you hit the nail on the head. The router was doing Iner-VLAN routing, but the PCs were blocking the pings because they came from another subnet. Thank you for your help in resolving this.
I have a follow-up question if I may - I need to add a default route but can't seem to find a way to do that. Tried adding a static route with IP=0.0.0.0 Mask=0.0.0.0 but it will not allow it. My current routing table looks like this:
Destination Gateway Genmask Metric Ref Use Interface Type Flags
127.0.0.1 127.0.0.1 255.255.255.255 1 0 0 lo Static UP,Gateway,Host
192.168.2.0 0.0.0.0 255.255.255.0 0 0 0 bdg2 Dynamic UP
192.168.1.0 0.0.0.0 255.255.255.0 0 0 0 bdg1 Static UP
127.0.0.0 0.0.0.0 255.0.0.0 0 0 0 lo Dynamic UP
It routes all packets to VLAN2 and VLAN3 correctly; but if a packet arrives to any other network address, I would like to get it to forward to another gateway on VLAN2 (at address 192.168.2.254). Can't seem to find a way to add a default route. -
Re: sub-interfaces - VLAN - Multiple contexts.
Ok so here is the scenario.
1) create 3 sub-interfaces on a physical interface.
2) create a VLAN and assign the same VLAN to sub-interfaces.
3) create 3 contexts and assign them to sub-interface.
Unfortunately I cannot assign the same VLAN to the 3 sub-interfaces as in step 2).
Therefore I am looking for an alernative solution.
Thanks, gordonOk I have some alternative solutions:
VLAN bridging.
seperate VRF.
Use other layer 3 device.
Vmware instance on host server.
Add Ethernet module to ASA.
The most cost effective although not standard is to use the management interface and implement VLAN bridging to overcome the conflict in step 2. -
I have setting the Management Interface Vlan Identifier to 0 or untagged.
If i change this to a vlan, I am unable to manage the device, is this correct?
SteveIf u make it untagged then specify the NATIVE vlan on the switchport..
If u tag the management interface, then dont configure the native vlan on the switchport..
Both the cases u will be able to access!!
Lemme know if this answered ur question!!
Regards
Surendra -
Hi guys,
I am trying to share two vlans in two different contexts but when I try to add the same vlan in the second context I receive this message: “Interface Vlan15 cannot be allocated to context. Interface is allocated to another context in a different failover group”. I have seen same example where you can share the same vlans; so I don’t know where is my fail.
http://www.cisco.com/en/US/docs/security/fwsm/fwsm31/configuration/guide/exampl_f.html#wp1029314
thanks.It sounds like what you're asking is about the concept of switched virtual interfaces - "interface vlan 10", for instance, is a switched virtual interface. This is different than a VLAN in that a VLAN is a logical network segment, a broadcast domain, whereas an SVI is a logical interface.
If SW2 is a layer 3 switch, you don't HAVE to have the SVI configured there. You could operate both SW1 and SW2 entirely as layer 2 devices, configure an interface on R1 to handle the inter-VLAN traffic, and configure the links from SW1-SW2 and SW2-R1 as trunks.
But that wastes the l3 capability of the switch. The idea is that you don't need to involve a router. When you have a vlan (layer 2), it has no way to communicate with other vlans (layer 2). That's where an SVI on a layer 3 switch, or an interface on a router (router-on-a-stick) using dot1q encapsulation comes in. It gives your devices in that VLAN something to point to as a gateway, something for routable traffic to address. So, think of a VLAN as a self contained network, and an SVI as the door that allows it to talk to everything else.
Also, in practice, assigning each discrete switch an IP address for management traffic makes things much easier - how else can you telnet/SSH into it? Beats having to use the console all the time!
HTH -
WiSM - Interface Vlan Overlapping within AP Group
Hi there,
Need help on this. Wism that deployed on the network had found issue in interface vlan overlapping. Had configured the vlan interface and assign to a group. The group had been define on specific lwapp APs. However user that manage to associate with the particular AP had used the different group that not specify to that APs. It had been using the group that been specify to other APs that located at different location.
Any ideas on this? Is this internal bugs? I had checked with the bugs listed in Cisco software. But not mentioned about this. Fyi, we are running on software version 4.1.171.0. and also we are operates almost of 80 Aps under 40 interface vlan assign to the groups.Could you provide the details of the wism configuration?
-
Hi
i need to know with detail what does it mean this command"passive interface vlan 50"?;description;usefulllink it is very much appreciated.
10xs
aliHi Ali,
"passive-interface" router configuration command is applied to stop sending routing updates on an interface.
It behaves different for different routing protocol like for EIGRP the passive-interface command disables the transmission and receipt of EIGRP hello packets on an interface so the neighborship will not form on that interface which is configured as passive interface.
In OSPF, hello packets are not sent on an interface that is specified as passive. Hence, the router will not be able to discover any neighbors, and none of the OSPF neighbors will be able to see the router on that network.
But for RIP and IGRP it does not send the routing updates out on that interface which is configured as passive but still that interface will be advertised out from other interfaces.
Have a look at this link for more details
http://www.cisco.com/en/US/products/sw/iosswrel/ps1830/products_feature_guide09186a008008784e.html#wp11573
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fipr_c/ipcprt2/1cfindep.htm#wp1019396
Now depending upon the routing protocol you have configured interface vlan 50 will not advertise the routes out from the interface vlan 50 and if you have configured eigrp or ospf it will not form any neighborship with peer on interface vlan 50.
HTH, if yes please rate the post.
Ankur -
I cannot get my MacBook Pro to print greyscale on my Canon MG6450. I cannot access the printer driver panel on the Macbook. So I am stuck printing everything in colour and cannot specify which pages I want printed.
Try resetting the printing system:
OS X Mavericks: Reset the printing system
Next try deleting the system and reinstall the printer..
BTW this is Mac Pro desktop forum -
"The interface name given does not specify a valid and existing interface."
Hi nice guys,
I'm trying to use the XNET APIs to set Master task to Slave with LIN protocol. As I have no Experience before, there's something problem like the Interface of the NI USB-8476S can't be detected. The prompted windows presents following infomation:
Error -1074384758 occurred at XNET Create Session (Signal Output Single-point).vi:1
Possible reason(s):
NI-XNET: (Hex 0xBFF6308A) The interface name given does not specify a valid and existing interface. Solution: Use a valid and existing interface. These can be obtained using MAX, XNET system properties, or the LabVIEW XNET Interface IO name. If you are using CompactRIO, refer to the topic "Getting Started with CompactRIO" in the NI-XNET Hardware and Software Help.
but in the NI MAX, the device is detected as "LIN0". Even the interface input control in the NI examples shows the error. But if I take the CAN Frame API, it works well.
Does anyone have some idea. I'm so preciate. Tanks in advance.
best regards
MeloMelonetern,
When do you receive these errors? Does this happen when you try to run your code or our examples? On top of that, does this error happen immediately or does it take a while? Is this happening in LabVIEW or another interface?
If you could give us the versions of software you are using as well as the XNET driver versions that would be very helpful.
Matt J
Professional Googler and Kudo Addict
National Instruments -
A constructor cannot specify a return type.
I have a shuffleList.as file with this code...
package {
import flash.display.MovieClip;
public class shuffleList extends MovieClip{
function shuffleList(arr:Array):Array{
var shuffled:Array = arr.slice();
for (var i:int=0; i<arr.length; i++) {
var element:Object = shuffled
var rnd:int = Math.floor(arr.length * Math.random());
shuffled = shuffled[rnd];
shuffled[rnd] = element;
return shuffled;
In the first frame i put this code...
import shuffleList
var numA:Array = [0,1,2,3,4,5,6,7,8,9,10]
var numB:Array = shuffleList(numB);
var myText:String = numB.pop()
fieldA.text = myText
With this code I want to put in random order the numbers from
0 to 10 in the fieldA.
When run this file the compiler report this error: "A
constructor cannot specify a return type."
Where I'm wrong;
I'm new in actionscript..
Please help...Hey Petros,
I had a similar problem and the response I got was:
1) the constructor is used to set up the class but it doesn't
really exist until it is instantiated and therefore cannot include
any 'interaction' including a return.
2) Therefore, you might try replacing
function.shuffleList ... with
function.shuffleList() { // to enable instantiation
public function doit(arr:Array):Array { // to enable
interaction
The rest of the code follows this then the call in the first
frame replaces
var numB:Array ... with
new shuffleList(); // instantiate the class
var numB:Array = shuffleList.doit(numB) // interact with the
class
Let me know how it goes...Daniel
Maybe you are looking for
-
How do I stop my contacts saving on 2 different iPhones???
I use the same apple account on 2 different iPhones.... How can I stop my contacts from saving on both phones???
-
Error Message When Uploading Book "One of Your Files.."
Hi, When I go to 'BUY' the book I created I keep getting the "Error Occurred with one of your files" message, and the upload does not go through. How can I tell what this error is(which photos), and is there another way to send the book in? Dina
-
Dear @all; do you know how I can change the Alert text language for my system log alert messages? In this case the MTE text is EN and the Alert Text is DE... where are these language settings active? ALERT for CRP icocma11_CRP_00 R3Syslog BasisSys
-
MBAM 2.0 - Complex PIN support
Hi Referring to windowsteamblog I found the following: Additionally, to protect machines during the pre-boot authentication process, we're adding complex PIN support to address situations where users attempt to set a weak PIN. How can configure compl
-
Hi ppl, The status of java instance is green in MMC but its not running. But when we try to reach the URL "http://hostname:50000/rep/start/index.html" its throwing an error stating "The Page cannot be displayed". what could be the reason behind